Configure the two accelerometers sharing GPIO line 82 as:
- Open drain so that they can share the same interrupt line.
Configure the corresponding interrupt pin:
- Trigger on the falling edge since open drain implies that we
do not actively drive the line high, but we will actively drive
it low to generate interrupts and then it moves from high to low
i.e. a falling edge.
- Pulled up so the line will be biased to high unless an IRQ
is active on any device on the line, and thus it goes high
again after the interrupt is deasserted.
Cc: linux-iio@xxxxxxxxxxxxxxx
Cc: Jonathan Cameron <jic23@xxxxxxxxx>
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
ChangeLog v1->v2:
- Switch to using the drive-mode-open-drain; setting
---
arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 12 +++++++-----
1 file changed, 7 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
index 55f9d0cc90f3..aec816c8ecb6 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
@@ -93,14 +93,15 @@
/* Accelerometer */
compatible = "st,lsm303dlh-accel";
st,drdy-int-pin = <1>;
+ drive-open-drain;
reg = <0x18>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&accel_tvk_mode>;
interrupt-parent = <&gpio2>;
- interrupts = <18 IRQ_TYPE_EDGE_RISING>,
- <19 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
+ <19 IRQ_TYPE_EDGE_FALLING>;
};
lsm303dlh@1e {
/*
@@ -118,14 +119,15 @@
/* Accelerometer */
compatible = "st,lis331dl-accel";
st,drdy-int-pin = <1>;
+ drive-open-drain;
reg = <0x1c>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&accel_tvk_mode>;
interrupt-parent = <&gpio2>;
- interrupts = <18 IRQ_TYPE_EDGE_RISING>,
- <19 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <18 IRQ_TYPE_EDGE_FALLING>,
+ <19 IRQ_TYPE_EDGE_FALLING>;
};
ak8974@0f {
/* Magnetometer */
@@ -216,7 +218,7 @@
/* Accelerometer interrupt lines 1 & 2 */
tvk_cfg {
pins = "GPIO82_C1", "GPIO83_D3";
- ste,config = <&gpio_in_pd>;
+ ste,config = <&gpio_in_pu>;
};
};
};
--
2.4.3
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
