On 11 April 2016 at 14:12, Linus Walleij <linus.walleij@xxxxxxxxxx> wrote:
> This is a reimplementation of the old misc device driver for the
> ROHM BH1780 ambient light sensor (drivers/misc/bh1780gli.c).
>
> Differences from the old driver:
> - Uses the IIO framework
> - Uses runtime PM to idle the hardware after 5 seconds
> - No weird custom power management from userspace
> - No homebrewn values in sysfs
>
> This uses the same (undocumented) device tree compatible-string
> as the old driver ("rohm,bh1780gli").
>
> Cc: Arnd Bergmann <arnd@xxxxxxxx>
> Cc: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
> Cc: Daniel Mack <daniel@xxxxxxxx>
> Cc: Peter Meerwald-Stadler <pmeerw@xxxxxxxxxx>
> Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
Reviewed-by: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
Kind regards
Uffe
> ---
> ChangeLog v4->v5:
> - Make sure to power down the device also in the module .remove()
> - Augment state container to contain a proper pointer to the
> indio device so it can be removed in .remove()
> - Use i2c_smbus_read_word_data() to read both LSB+MSB in
> one swift transaction and return it back to IIO.
> ChangeLog v3->v4:
> - Set the system suspend PM ops to pm_force_[suspend|resume]
> so we are in low power also in system suspend.
> - Error prints for failed I2C transactions in runtime
> suspend/resume
> ChangeLog v2->v3:
> - Dropped the _scale information just returning "1" from
> sysfs, userspace should assume scale by 1 if not present.
> - Dropped CC to maintainers who seemingly fell off the planet.
> ChangeLog v1->v2:
> - Use <linux/bitops.h>, BIT(), GENMASK()
> - Do not read state first when suspending.
> - Do not cast debug reg access return value.
> - Whitespace, comments.
>
> I want to phase out the old misc driver, but don't know how that
> should properly be handled. The driver has an old (totally
> undocumented) sysfs ABI for raw measurements, should I add
> this as backward-compatibility and symlink the device to the old
> location?
> ---
> drivers/iio/light/Kconfig | 11 ++
> drivers/iio/light/Makefile | 1 +
> drivers/iio/light/bh1780.c | 298 +++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 310 insertions(+)
> create mode 100644 drivers/iio/light/bh1780.c
>
> diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig
> index cfd3df8416bb..5ee1d453b3d8 100644
> --- a/drivers/iio/light/Kconfig
> +++ b/drivers/iio/light/Kconfig
> @@ -73,6 +73,17 @@ config BH1750
> To compile this driver as a module, choose M here: the module will
> be called bh1750.
>
> +config BH1780
> + tristate "ROHM BH1780 ambient light sensor"
> + depends on I2C
> + depends on !SENSORS_BH1780
> + help
> + Say Y here to build support for the ROHM BH1780GLI ambient
> + light sensor.
> +
> + To compile this driver as a module, choose M here: the module will
> + be called bh1780.
> +
> config CM32181
> depends on I2C
> tristate "CM32181 driver"
> diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile
> index b2c31053db0c..4aeee2bd8f49 100644
> --- a/drivers/iio/light/Makefile
> +++ b/drivers/iio/light/Makefile
> @@ -9,6 +9,7 @@ obj-$(CONFIG_AL3320A) += al3320a.o
> obj-$(CONFIG_APDS9300) += apds9300.o
> obj-$(CONFIG_APDS9960) += apds9960.o
> obj-$(CONFIG_BH1750) += bh1750.o
> +obj-$(CONFIG_BH1780) += bh1780.o
> obj-$(CONFIG_CM32181) += cm32181.o
> obj-$(CONFIG_CM3232) += cm3232.o
> obj-$(CONFIG_CM3323) += cm3323.o
> diff --git a/drivers/iio/light/bh1780.c b/drivers/iio/light/bh1780.c
> new file mode 100644
> index 000000000000..d78a3cf81551
> --- /dev/null
> +++ b/drivers/iio/light/bh1780.c
> @@ -0,0 +1,298 @@
> +/*
> + * ROHM 1780GLI Ambient Light Sensor Driver
> + *
> + * Copyright (C) 2016 Linaro Ltd.
> + * Author: Linus Walleij <linus.walleij@xxxxxxxxxx>
> + * Loosely based on the previous BH1780 ALS misc driver
> + * Copyright (C) 2010 Texas Instruments
> + * Author: Hemanth V <hemanthv@xxxxxx>
> + */
> +#include <linux/i2c.h>
> +#include <linux/slab.h>
> +#include <linux/platform_device.h>
> +#include <linux/delay.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/sysfs.h>
> +#include <linux/bitops.h>
> +
> +#define BH1780_CMD_BIT BIT(7)
> +#define BH1780_REG_CONTROL 0x00
> +#define BH1780_REG_PARTID 0x0A
> +#define BH1780_REG_MANFID 0x0B
> +#define BH1780_REG_DLOW 0x0C
> +#define BH1780_REG_DHIGH 0x0D
> +
> +#define BH1780_REVMASK GENMASK(3,0)
> +#define BH1780_POWMASK GENMASK(1,0)
> +#define BH1780_POFF (0x0)
> +#define BH1780_PON (0x3)
> +
> +/* power on settling time in ms */
> +#define BH1780_PON_DELAY 2
> +/* max time before value available in ms */
> +#define BH1780_INTERVAL 250
> +
> +struct bh1780_data {
> + struct i2c_client *client;
> + struct iio_dev *indio_dev;
> +};
> +
> +static int bh1780_write(struct bh1780_data *bh1780, u8 reg, u8 val)
> +{
> + int ret = i2c_smbus_write_byte_data(bh1780->client,
> + BH1780_CMD_BIT | reg,
> + val);
> + if (ret < 0)
> + dev_err(&bh1780->client->dev,
> + "i2c_smbus_write_byte_data failed error "
> + "%d, register %01x\n",
> + ret, reg);
> + return ret;
> +}
> +
> +static int bh1780_read(struct bh1780_data *bh1780, u8 reg)
> +{
> + int ret = i2c_smbus_read_byte_data(bh1780->client,
> + BH1780_CMD_BIT | reg);
> + if (ret < 0)
> + dev_err(&bh1780->client->dev,
> + "i2c_smbus_read_byte_data failed error "
> + "%d, register %01x\n",
> + ret, reg);
> + return ret;
> +}
> +
> +static int bh1780_read_word(struct bh1780_data *bh1780, u8 reg)
> +{
> + int ret = i2c_smbus_read_word_data(bh1780->client,
> + BH1780_CMD_BIT | reg);
> + if (ret < 0)
> + dev_err(&bh1780->client->dev,
> + "i2c_smbus_read_word_data failed error "
> + "%d, register %01x\n",
> + ret, reg);
> + return ret;
> +}
> +
> +int bh1780_debugfs_reg_access(struct iio_dev *indio_dev,
> + unsigned int reg, unsigned int writeval,
> + unsigned int *readval)
> +{
> + struct bh1780_data *bh1780 = iio_priv(indio_dev);
> + int ret;
> +
> + if (!readval)
> + bh1780_write(bh1780, (u8)reg, (u8)writeval);
> +
> + ret = bh1780_read(bh1780, (u8)reg);
> + if (ret < 0)
> + return ret;
> +
> + *readval = ret;
> +
> + return 0;
> +}
> +
> +static int bh1780_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + struct bh1780_data *bh1780 = iio_priv(indio_dev);
> + int value;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + switch (chan->type) {
> + case IIO_LIGHT:
> + pm_runtime_get_sync(&bh1780->client->dev);
> + value = bh1780_read_word(bh1780, BH1780_REG_DLOW);
> + if (value < 0)
> + return value;
> + pm_runtime_mark_last_busy(&bh1780->client->dev);
> + pm_runtime_put_autosuspend(&bh1780->client->dev);
> + *val = value;
> +
> + return IIO_VAL_INT;
> + default:
> + return -EINVAL;
> + }
> + case IIO_CHAN_INFO_INT_TIME:
> + *val = 0;
> + *val2 = BH1780_INTERVAL * 1000;
> + return IIO_VAL_INT_PLUS_MICRO;
> + default:
> + return -EINVAL;
> + }
> +}
> +
> +static const struct iio_info bh1780_info = {
> + .driver_module = THIS_MODULE,
> + .read_raw = bh1780_read_raw,
> + .debugfs_reg_access = bh1780_debugfs_reg_access,
> +};
> +
> +static const struct iio_chan_spec bh1780_channels[] = {
> + {
> + .type = IIO_LIGHT,
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
> + BIT(IIO_CHAN_INFO_INT_TIME)
> + }
> +};
> +
> +static int bh1780_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + int ret;
> + struct bh1780_data *bh1780;
> + struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
> + struct iio_dev *indio_dev;
> +
> + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
> + return -EIO;
> +
> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*bh1780));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + bh1780 = iio_priv(indio_dev);
> + bh1780->client = client;
> + bh1780->indio_dev = indio_dev;
> + i2c_set_clientdata(client, bh1780);
> +
> + /* Power up the device */
> + ret = bh1780_write(bh1780, BH1780_REG_CONTROL, BH1780_PON);
> + if (ret < 0)
> + return ret;
> + msleep(BH1780_PON_DELAY);
> + pm_runtime_get_noresume(&client->dev);
> + pm_runtime_set_active(&client->dev);
> + pm_runtime_enable(&client->dev);
> +
> + ret = bh1780_read(bh1780, BH1780_REG_PARTID);
> + if (ret < 0)
> + goto out_disable_pm;
> + dev_info(&client->dev,
> + "Ambient Light Sensor, Rev : %lu\n",
> + (ret & BH1780_REVMASK));
> +
> + /*
> + * As the device takes 250 ms to even come up with a fresh
> + * measurement after power-on, do not shut it down unnecessarily.
> + * Set autosuspend to a five seconds.
> + */
> + pm_runtime_set_autosuspend_delay(&client->dev, 5000);
> + pm_runtime_use_autosuspend(&client->dev);
> + pm_runtime_put(&client->dev);
> +
> + indio_dev->dev.parent = &client->dev;
> + indio_dev->info = &bh1780_info;
> + indio_dev->name = id->name;
> + indio_dev->channels = bh1780_channels;
> + indio_dev->num_channels = ARRAY_SIZE(bh1780_channels);
> + indio_dev->modes = INDIO_DIRECT_MODE;
> +
> + ret = iio_device_register(indio_dev);
> + if (ret)
> + goto out_disable_pm;
> + return 0;
> +
> +out_disable_pm:
> + pm_runtime_put_noidle(&client->dev);
> + pm_runtime_disable(&client->dev);
> + return ret;
> +}
> +
> +static int bh1780_remove(struct i2c_client *client)
> +{
> + struct bh1780_data *bh1780 = i2c_get_clientdata(client);
> + int ret;
> +
> + iio_device_unregister(bh1780->indio_dev);
> + pm_runtime_get_sync(&client->dev);
> + pm_runtime_put_noidle(&client->dev);
> + pm_runtime_disable(&client->dev);
> + ret = bh1780_write(bh1780, BH1780_REG_CONTROL, BH1780_POFF);
> + if (ret < 0) {
> + dev_err(&client->dev, "failed to power off\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_PM
> +static int bh1780_runtime_suspend(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct bh1780_data *bh1780 = i2c_get_clientdata(client);
> + int ret;
> +
> + ret = bh1780_write(bh1780, BH1780_REG_CONTROL, BH1780_POFF);
> + if (ret < 0) {
> + dev_err(dev, "failed to runtime suspend\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int bh1780_runtime_resume(struct device *dev)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct bh1780_data *bh1780 = i2c_get_clientdata(client);
> + int ret;
> +
> + ret = bh1780_write(bh1780, BH1780_REG_CONTROL, BH1780_PON);
> + if (ret < 0) {
> + dev_err(dev, "failed to runtime resume\n");
> + return ret;
> + }
> +
> + /* Wait for power on, then for a value to be available */
> + msleep(BH1780_PON_DELAY + BH1780_INTERVAL);
> +
> + return 0;
> +}
> +#endif /* CONFIG_PM */
> +
> +static const struct dev_pm_ops bh1780_dev_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> + pm_runtime_force_resume)
> + SET_RUNTIME_PM_OPS(bh1780_runtime_suspend,
> + bh1780_runtime_resume, NULL)
> +};
> +
> +static const struct i2c_device_id bh1780_id[] = {
> + { "bh1780", 0 },
> + { },
> +};
> +
> +MODULE_DEVICE_TABLE(i2c, bh1780_id);
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id of_bh1780_match[] = {
> + { .compatible = "rohm,bh1780gli", },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, of_bh1780_match);
> +#endif
> +
> +static struct i2c_driver bh1780_driver = {
> + .probe = bh1780_probe,
> + .remove = bh1780_remove,
> + .id_table = bh1780_id,
> + .driver = {
> + .name = "bh1780",
> + .pm = &bh1780_dev_pm_ops,
> + .of_match_table = of_match_ptr(of_bh1780_match),
> + },
> +};
> +
> +module_i2c_driver(bh1780_driver);
> +
> +MODULE_DESCRIPTION("ROHM BH1780GLI Ambient Light Sensor Driver");
> +MODULE_LICENSE("GPL");
> +MODULE_AUTHOR("Linus Walleij <linus.walleij@xxxxxxxxxx>");
> --
> 2.4.3
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
