Add support for HopeRF pressure and temperature sensor.
This device uses two fixed I2C addresses, one for storing
calibration coefficients and another for accessing the ADC.
Signed-off-by: Marek Vasut <marex@xxxxxxx>
Cc: Matt Ranostay <mranostay@xxxxxxxxx>
Cc: Jonathan Cameron <jic23@xxxxxxxxxx>
---
V2: - Expand the binding document with more details on the XCLR pin
- Switch from IIO_CHAN_INFO_PROCESSED to RAW + SCALE
- Add failpath into hp03_update_temp_pressure() for the case
when ADC readout fails. This correctly sets the XCLR pin back
to LO now.
- Add comment explaining the need for allocation of child device
in hp03_probe().
---
.../devicetree/bindings/iio/pressure/hp03.txt | 17 ++
drivers/iio/pressure/Kconfig | 11 +
drivers/iio/pressure/Makefile | 1 +
drivers/iio/pressure/hp03.c | 314 +++++++++++++++++++++
4 files changed, 343 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/pressure/hp03.txt
create mode 100644 drivers/iio/pressure/hp03.c
diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt
new file mode 100644
index 0000000..ceec03e
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/pressure/hp03.txt
@@ -0,0 +1,17 @@
+HopeRF HP03 digital pressure/temperature sensors
+
+Required properties:
+- compatible: must be "hoperf,hp03"
+- xclr-gpio: must be device tree identifier of the XCLR pin .
+ The XCLR pin is a reset of the ADC in the chip,
+ it must be pulled HI before the conversion and
+ readout of the value from the ADC registers and
+ pulled LO afterward.
+
+Example:
+
+hp03@0x77 {
+ compatible = "hoperf,hp03";
+ reg = <0x77>;
+ xclr-gpio = <&portc 0 0x0>;
+};
diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig
index 31c0e1f..3f2b1ed 100644
--- a/drivers/iio/pressure/Kconfig
+++ b/drivers/iio/pressure/Kconfig
@@ -30,6 +30,17 @@ config HID_SENSOR_PRESS
To compile this driver as a module, choose M here: the module
will be called hid-sensor-press.
+config HP03
+ tristate "Hope RF HP03 temperature and pressure sensor driver"
+ depends on I2C
+ select REGMAP_I2C
+ help
+ Say yes here to build support for Hope RF HP03 pressure and
+ temperature sensor.
+
+ To compile this driver as a module, choose M here: the module
+ will be called hp03.
+
config MPL115
tristate
diff --git a/drivers/iio/pressure/Makefile b/drivers/iio/pressure/Makefile
index d336af1..cb21ab1 100644
--- a/drivers/iio/pressure/Makefile
+++ b/drivers/iio/pressure/Makefile
@@ -5,6 +5,7 @@
# When adding new entries keep the list in alphabetical order
obj-$(CONFIG_BMP280) += bmp280.o
obj-$(CONFIG_HID_SENSOR_PRESS) += hid-sensor-press.o
+obj-$(CONFIG_HP03) += hp03.o
obj-$(CONFIG_MPL115) += mpl115.o
obj-$(CONFIG_MPL115_I2C) += mpl115_i2c.o
obj-$(CONFIG_MPL115_SPI) += mpl115_spi.o
diff --git a/drivers/iio/pressure/hp03.c b/drivers/iio/pressure/hp03.c
new file mode 100644
index 0000000..4df1729
--- /dev/null
+++ b/drivers/iio/pressure/hp03.c
@@ -0,0 +1,314 @@
+/*
+ * Copyright (c) 2016 Marek Vasut <marex@xxxxxxx>
+ *
+ * Driver for Hope RF HP03 digital temperature and pressure sensor.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define pr_fmt(fmt) "hp03: " fmt
+
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+
+/*
+ * The HP03 sensor occupies two fixed I2C addresses:
+ * 0x50 ... read-only EEPROM with calibration data
+ * 0x77 ... read-write ADC for pressure and temperature
+ */
+#define HP03_EEPROM_ADDR 0x50
+#define HP03_ADC_ADDR 0x77
+
+#define HP03_EEPROM_CX_OFFSET 0x10
+#define HP03_EEPROM_AB_OFFSET 0x1e
+#define HP03_EEPROM_CD_OFFSET 0x20
+
+#define HP03_ADC_WRITE_REG 0xff
+#define HP03_ADC_READ_REG 0xfd
+#define HP03_ADC_READ_PRESSURE 0xf0 /* D1 in datasheet */
+#define HP03_ADC_READ_TEMP 0xe8 /* D2 in datasheet */
+
+struct hp03_priv {
+ struct i2c_client *client;
+ struct mutex lock;
+ struct gpio_desc *xclr_gpio;
+
+ struct i2c_client *eeprom_client;
+ struct regmap *eeprom_regmap;
+
+ s32 pressure; /* kPa */
+ s32 temp; /* Deg. C */
+};
+
+static const struct iio_chan_spec hp03_channels[] = {
+ {
+ .type = IIO_PRESSURE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
+ },
+ {
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
+ },
+};
+
+static bool hp03_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+ return false;
+}
+
+static bool hp03_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ return false;
+}
+
+static const struct regmap_config hp03_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = HP03_EEPROM_CD_OFFSET + 1,
+ .cache_type = REGCACHE_RBTREE,
+
+ .writeable_reg = hp03_is_writeable_reg,
+ .volatile_reg = hp03_is_volatile_reg,
+};
+
+static int hp03_get_temp_pressure(struct hp03_priv *priv, const u8 reg)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(priv->client, HP03_ADC_WRITE_REG, reg);
+ if (ret < 0)
+ return ret;
+
+ msleep(50); /* Wait for conversion to finish */
+
+ return i2c_smbus_read_word_data(priv->client, HP03_ADC_READ_REG);
+}
+
+static int hp03_update_temp_pressure(struct hp03_priv *priv)
+{
+ struct device *dev = &priv->client->dev;
+ u8 coefs[18];
+ u16 cx_val[7];
+ int ab_val, d1_val, d2_val, diff_val, dut, off, sens, x;
+ int i, ret;
+
+ /* Sample coefficients from EEPROM */
+ ret = regmap_bulk_read(priv->eeprom_regmap, HP03_EEPROM_CX_OFFSET,
+ coefs, sizeof(coefs));
+ if (ret < 0) {
+ dev_err(dev, "Failed to read EEPROM (reg=%02x)\n",
+ HP03_EEPROM_CX_OFFSET);
+ return ret;
+ }
+
+ /* Sample Temperature and Pressure */
+ gpiod_set_value_cansleep(priv->xclr_gpio, 1);
+
+ ret = hp03_get_temp_pressure(priv, HP03_ADC_READ_PRESSURE);
+ if (ret < 0) {
+ dev_err(dev, "Failed to read pressure\n");
+ goto err_adc;
+ }
+ d1_val = ret;
+
+ ret = hp03_get_temp_pressure(priv, HP03_ADC_READ_TEMP);
+ if (ret < 0) {
+ dev_err(dev, "Failed to read temperature\n");
+ goto err_adc;
+ }
+ d2_val = ret;
+
+ gpiod_set_value_cansleep(priv->xclr_gpio, 0);
+
+ /* The Cx coefficients and Temp/Pressure values are MSB first. */
+ for (i = 0; i < 7; i++)
+ cx_val[i] = (coefs[2 * i] << 8) | (coefs[(2 * i) + 1] << 0);
+ d1_val = ((d1_val >> 8) & 0xff) | ((d1_val & 0xff) << 8);
+ d2_val = ((d2_val >> 8) & 0xff) | ((d2_val & 0xff) << 8);
+
+ /* Coefficient voodoo from the HP03 datasheet. */
+ if (d2_val >= cx_val[4])
+ ab_val = coefs[14]; /* A-value */
+ else
+ ab_val = coefs[15]; /* B-value */
+
+ diff_val = d2_val - cx_val[4];
+ dut = (ab_val * (diff_val >> 7) * (diff_val >> 7)) >> coefs[16];
+ dut = diff_val - dut;
+
+ off = (cx_val[1] + (((cx_val[3] - 1024) * dut) >> 14)) * 4;
+ sens = cx_val[0] + ((cx_val[2] * dut) >> 10);
+ x = ((sens * (d1_val - 7168)) >> 14) - off;
+
+ priv->pressure = ((x * 100) >> 5) + (cx_val[6] * 10);
+ priv->temp = 250 + ((dut * cx_val[5]) >> 16) - (dut >> coefs[17]);
+
+ return 0;
+
+err_adc:
+ gpiod_set_value_cansleep(priv->xclr_gpio, 0);
+ return ret;
+}
+
+static int hp03_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ struct hp03_priv *priv = iio_priv(indio_dev);
+ int ret;
+
+ mutex_lock(&priv->lock);
+ ret = hp03_update_temp_pressure(priv);
+ mutex_unlock(&priv->lock);
+
+ if (ret)
+ return ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ switch (chan->type) {
+ case IIO_PRESSURE:
+ *val = priv->pressure / 100;
+ *val2 = (priv->pressure % 100) * 10000;
+ ret = IIO_VAL_INT_PLUS_MICRO;
+ break;
+ case IIO_TEMP:
+ *val = priv->temp / 100;
+ *val2 = (priv->temp % 100) * 10000;
+ ret = IIO_VAL_INT_PLUS_MICRO;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+ break;
+ case IIO_CHAN_INFO_SCALE:
+ switch (chan->type) {
+ case IIO_PRESSURE:
+ case IIO_TEMP:
+ *val = 0;
+ *val2 = 10000;
+ ret = IIO_VAL_INT_PLUS_MICRO;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+ break;
+
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ return ret;
+}
+
+static const struct iio_info hp03_info = {
+ .driver_module = THIS_MODULE,
+ .read_raw = &hp03_read_raw,
+};
+
+static int hp03_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct iio_dev *indio_dev;
+ struct hp03_priv *priv;
+ int ret;
+
+ indio_dev = devm_iio_device_alloc(dev, sizeof(*priv));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ priv = iio_priv(indio_dev);
+ priv->client = client;
+ mutex_init(&priv->lock);
+
+ indio_dev->dev.parent = dev;
+ indio_dev->name = id->name;
+ indio_dev->channels = hp03_channels;
+ indio_dev->num_channels = ARRAY_SIZE(hp03_channels);
+ indio_dev->info = &hp03_info;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+
+ /*
+ * Allocate another device for the on-sensor EEPROM,
+ * which has it's dedicated I2C address and contains
+ * the calibration constants for the sensor.
+ */
+ priv->eeprom_client = i2c_new_dummy(client->adapter, HP03_EEPROM_ADDR);
+ if (!priv->eeprom_client) {
+ dev_err(dev, "New EEPROM I2C device failed\n");
+ return -ENODEV;
+ }
+
+ priv->eeprom_regmap = devm_regmap_init_i2c(priv->eeprom_client,
+ &hp03_regmap_config);
+ if (IS_ERR(priv->eeprom_regmap)) {
+ dev_err(dev, "Failed to allocate EEPROM regmap\n");
+ ret = PTR_ERR(priv->eeprom_regmap);
+ goto err;
+ }
+
+ priv->xclr_gpio = devm_gpiod_get_index(dev, "xclr", 0, GPIOD_OUT_HIGH);
+ if (IS_ERR(priv->xclr_gpio)) {
+ dev_err(dev, "Failed to claim XCLR GPIO\n");
+ ret = PTR_ERR(priv->xclr_gpio);
+ goto err;
+ }
+
+ ret = devm_iio_device_register(dev, indio_dev);
+ if (ret) {
+ dev_err(dev, "Failed to register IIO device\n");
+ goto err;
+ }
+
+ i2c_set_clientdata(client, indio_dev);
+
+ return 0;
+
+err:
+ i2c_unregister_device(priv->eeprom_client);
+ return ret;
+}
+
+static int hp03_remove(struct i2c_client *client)
+{
+ struct iio_dev *indio_dev = i2c_get_clientdata(client);
+ struct hp03_priv *priv = iio_priv(indio_dev);
+
+ i2c_unregister_device(priv->eeprom_client);
+
+ return 0;
+}
+
+static const struct i2c_device_id hp03_id[] = {
+ { "hp03", 0 },
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, hp03_id);
+
+static struct i2c_driver hp03_driver = {
+ .driver = {
+ .name = "hp03",
+ },
+ .probe = hp03_probe,
+ .remove = hp03_remove,
+ .id_table = hp03_id,
+};
+module_i2c_driver(hp03_driver);
+
+MODULE_AUTHOR("Marek Vasut <marex@xxxxxxx>");
+MODULE_DESCRIPTION("Driver for Hope RF HP03 pressure and temperature sensor");
+MODULE_LICENSE("GPL v2");
--
2.7.0
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
