On 04/01/16 14:49, Harald Geyer wrote:
> Jonathan Cameron writes:
>> On 30/12/15 14:26, Harald Geyer wrote:
>>> * Unify log messages
>>> * Add more DEBUG messages
>>>
>>> Apparently this driver is working unreliably on some platforms that I can't
>>> test. Therefore I want an easy way for bug reporters to provide useful
>>> information without making the driver too chatty by default.
>>>
>>> Signed-off-by: Harald Geyer <harald@xxxxxxxxx>
>> Basically fine, though I'd loose the #ifdefs.
>>
>> Jonathan
>>> ---
>>> drivers/iio/humidity/dht11.c | 40 ++++++++++++++++++++++++++++++++++------
>>> 1 file changed, 34 insertions(+), 6 deletions(-)
>>>
>>> diff --git a/drivers/iio/humidity/dht11.c b/drivers/iio/humidity/dht11.c
>>> index cd1477d..f0cb28c 100644
>>> --- a/drivers/iio/humidity/dht11.c
>>> +++ b/drivers/iio/humidity/dht11.c
>>> @@ -96,6 +96,24 @@ struct dht11 {
>>> struct {s64 ts; int value; } edges[DHT11_EDGES_PER_READ];
>>> };
>>>
>>> +#ifdef CONFIG_DYNAMIC_DEBUG
>>> +/*
>>> + * dht11_edges_print: show the data as actually received by the
>>> + * driver.
>>> + */
>>> +static void dht11_edges_print(struct dht11 *dht11)
>>> +{
>>> + int i;
>>> +
>>> + dev_dbg(dht11->dev, "%d edges detected:\n", dht11->num_edges);
>>> + for (i = 1; i < dht11->num_edges; ++i) {
>>> + dev_dbg(dht11->dev, "%d: %lld ns %s\n", i,
>>> + dht11->edges[i].ts - dht11->edges[i - 1].ts,
>>> + dht11->edges[i - 1].value ? "high" : "low");
>>> + }
>>> +}
>>> +#endif /* CONFIG_DYNAMIC_DEBUG */
>> Hmm. I guess the ifdef is to avoid having the overhead in all cases.
>> I'd be more included to leave it out as the overhead isn't huge...
>
> Actually my reason was that this particular function is very chatty
> writing more than 80 lines of output. This can easily push more important
> lines out of the ring buffer. So I thought an easy way to turn it off
> without recompiling the kernel is appropriate.
>
>> Also it's more than possible people will want to use traditional
>> non dynamic debug for this...
>
> I don't expect so, but I entirely rely on your judgement in this case.
> What do you want to have there instead?
Not sure there is a good solution to this. The issues is accidental enabling
of the function by setting DEBUG as well as the dynamic config option as that
will make all the dynamic stuff default to on. You can turn it off explicitly
but it seems unlikely that will be done by users...
I guess perhaps your solution is the best one though it's not exactly
a tidy solution!
Jonathan
>
> Thanks,
> Harald
>
>>> +
>>> static unsigned char dht11_decode_byte(char *bits)
>>> {
>>> unsigned char ret = 0;
>>> @@ -119,8 +137,12 @@ static int dht11_decode(struct dht11 *dht11, int offset)
>>> for (i = 0; i < DHT11_BITS_PER_READ; ++i) {
>>> t = dht11->edges[offset + 2 * i + 2].ts -
>>> dht11->edges[offset + 2 * i + 1].ts;
>>> - if (!dht11->edges[offset + 2 * i + 1].value)
>>> - return -EIO; /* lost synchronisation */
>>> + if (!dht11->edges[offset + 2 * i + 1].value) {
>>> + dev_dbg(dht11->dev,
>>> + "lost synchronisation at edge %d\n",
>>> + offset + 2 * i + 1);
>>> + return -EIO;
>>> + }
>>> bits[i] = t > DHT11_THRESHOLD ? 1 : 0;
>>> }
>>>
>>> @@ -130,8 +152,10 @@ static int dht11_decode(struct dht11 *dht11, int offset)
>>> temp_dec = dht11_decode_byte(&bits[24]);
>>> checksum = dht11_decode_byte(&bits[32]);
>>>
>>> - if (((hum_int + hum_dec + temp_int + temp_dec) & 0xff) != checksum)
>>> + if (((hum_int + hum_dec + temp_int + temp_dec) & 0xff) != checksum) {
>>> + dev_dbg(dht11->dev, "invalid checksum\n");
>>> return -EIO;
>>> + }
>>>
>>> dht11->timestamp = ktime_get_real_ns();
>>> if (hum_int < 20) { /* DHT22 */
>>> @@ -182,6 +206,7 @@ static int dht11_read_raw(struct iio_dev *iio_dev,
>>> mutex_lock(&dht11->lock);
>>> if (dht11->timestamp + DHT11_DATA_VALID_TIME < ktime_get_real_ns()) {
>>> timeres = ktime_get_resolution_ns();
>>> + dev_dbg(dht11->dev, "current timeresolution: %dns\n", timeres);
>>> if (timeres > DHT11_MIN_TIMERES) {
>>> dev_err(dht11->dev, "timeresolution %dns too low\n",
>>> timeres);
>>> @@ -219,10 +244,13 @@ static int dht11_read_raw(struct iio_dev *iio_dev,
>>>
>>> free_irq(dht11->irq, iio_dev);
>>>
>>> +#ifdef CONFIG_DYNAMIC_DEBUG
>>> + dht11_edges_print(dht11);
>>> +#endif
>>> +
>>> if (ret == 0 && dht11->num_edges < DHT11_EDGES_PER_READ - 1) {
>>> - dev_err(&iio_dev->dev,
>>> - "Only %d signal edges detected\n",
>>> - dht11->num_edges);
>>> + dev_err(dht11->dev, "Only %d signal edges detected\n",
>>> + dht11->num_edges);
>>> ret = -ETIMEDOUT;
>>> }
>>> if (ret < 0)
>>>
>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
