Am 25. Oktober 2015 12:05:05 MEZ, schrieb Jonathan Cameron <jic23@xxxxxxxxxx>:
>On 22/10/15 19:22, Rob Herring wrote:
>> On Thu, Oct 15, 2015 at 8:10 AM, Martin Kepplinger
><martink@xxxxxxxxx> wrote:
>>> This change is important in order for everyone to be easily able to
>use the
>>> driver for one of the supported accelerometer chips!
>>>
>>> Until now, the driver blindly assumed that the INT1 interrupt line
>is wired
>>> on a user's board. But these devices have 2 interrupt lines and can
>route
>>> their interrupt sources to one of them. Now, if "INT2" is found and
>matches
>>> i2c_client->irq, INT2 will be used.
>>>
>>> The chip's default actually is INT2, which is why probably many
>boards will
>>> have it wired and can make use of this.
>>>
>>> Of course, this also falls back to assuming INT1, so for existing
>users
>>> nothing will break. The new functionality is described in the
>bindings doc.
>>>
>>> Signed-off-by: Martin Kepplinger
><martin.kepplinger@xxxxxxxxxxxxxxxxxxxxx>
>>> ---
>>> changelog:
>>> v4: use irq that matches client->irq, backwards compatible
>>> v3: correctly assign irq if both pins are described in DT
>>> v2: don't warn but normally handle if both pins are described in dts
>>> thanks Mark Rutland
>>> v1: initial post
>>>
>>> .../devicetree/bindings/iio/accel/mma8452.txt | 6 ++++++
>>
>> For the binding:
>>
>> Rob Herring <robh@xxxxxxxxxx>
>I've guessed that was an Acked-by :)
>
>Anyhow, applied to the togreg branch of iio.git.
>
>I'm afraid after my hiatus for a couple of weeks (day job work crisis
>now
>over) this has missed going in for the current cycle.
>
>IIO merge closes more than a week before the merge window opens and
>Linus
>just announced probably release a week today.
>
>Sorry about that, will be queued up for an early entry into linux next
>after the merge window closes.
>
>Jonathan
That's fine. Thanks
>>
>>> drivers/iio/accel/mma8452.c | 21
>+++++++++++++++------
>>> 2 files changed, 21 insertions(+), 6 deletions(-)
>>>
>>> diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt
>b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
>>> index e3c3746..3c10e85 100644
>>> --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt
>>> +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
>>> @@ -7,13 +7,18 @@ Required properties:
>>> * "fsl,mma8453"
>>> * "fsl,mma8652"
>>> * "fsl,mma8653"
>>> +
>>> - reg: the I2C address of the chip
>>>
>>> Optional properties:
>>>
>>> - interrupt-parent: should be the phandle for the interrupt
>controller
>>> +
>>> - interrupts: interrupt mapping for GPIO IRQ
>>>
>>> + - interrupt-names: should contain "INT1" and/or "INT2", the
>accelerometer's
>>> + interrupt line in use.
>>> +
>>> Example:
>>>
>>> mma8453fc@1d {
>>> @@ -21,4 +26,5 @@ Example:
>>> reg = <0x1d>;
>>> interrupt-parent = <&gpio1>;
>>> interrupts = <5 0>;
>>> + interrupt-names = "INT2";
>>> };
>>> diff --git a/drivers/iio/accel/mma8452.c
>b/drivers/iio/accel/mma8452.c
>>> index 1eccc2d..116a6e4 100644
>>> --- a/drivers/iio/accel/mma8452.c
>>> +++ b/drivers/iio/accel/mma8452.c
>>> @@ -29,6 +29,7 @@
>>> #include <linux/iio/events.h>
>>> #include <linux/delay.h>
>>> #include <linux/of_device.h>
>>> +#include <linux/of_irq.h>
>>>
>>> #define MMA8452_STATUS 0x00
>>> #define MMA8452_STATUS_DRDY (BIT(2) | BIT(1) |
>BIT(0))
>>> @@ -1130,13 +1131,21 @@ static int mma8452_probe(struct i2c_client
>*client,
>>> MMA8452_INT_FF_MT;
>>> int enabled_interrupts = MMA8452_INT_TRANS |
>>> MMA8452_INT_FF_MT;
>>> + int irq2;
>>>
>>> - /* Assume wired to INT1 pin */
>>> - ret = i2c_smbus_write_byte_data(client,
>>> - MMA8452_CTRL_REG5,
>>> -
>supported_interrupts);
>>> - if (ret < 0)
>>> - return ret;
>>> + irq2 = of_irq_get_byname(client->dev.of_node,
>"INT2");
>>> +
>>> + if (irq2 == client->irq) {
>>> + dev_dbg(&client->dev, "using interrupt line
>INT2\n");
>>> + } else {
>>> + ret = i2c_smbus_write_byte_data(client,
>>> +
>MMA8452_CTRL_REG5,
>>> +
>supported_interrupts);
>>> + if (ret < 0)
>>> + return ret;
>>> +
>>> + dev_dbg(&client->dev, "using interrupt line
>INT1\n");
>>> + }
>>>
>>> ret = i2c_smbus_write_byte_data(client,
>>> MMA8452_CTRL_REG4,
>>> --
>>> 2.1.4
>>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-iio"
>in
>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
