On 04/10/15 15:10, Jonathan Cameron wrote: > On 01/10/15 15:13, Ludovic Tancerel wrote: >> Support for HTU21 temperature & humidity sensor >> >> Signed-off-by: Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx> > Applied. A bit of fuzz due to other drivers having gone in recently > plus a bit of space to tab conversion for the documentation file. Also, the probe function was not marked as static. Is now. > > Thanks, > Jonathan >> --- >> Documentation/ABI/testing/sysfs-bus-iio | 10 ++ >> drivers/iio/humidity/Kconfig | 11 ++ >> drivers/iio/humidity/Makefile | 1 + >> drivers/iio/humidity/htu21.c | 226 ++++++++++++++++++++++++++++++++ >> 4 files changed, 248 insertions(+) >> create mode 100644 drivers/iio/humidity/htu21.c >> >> diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio >> index 70c9b1a..aac134a 100644 >> --- a/Documentation/ABI/testing/sysfs-bus-iio >> +++ b/Documentation/ABI/testing/sysfs-bus-iio >> @@ -1461,3 +1461,13 @@ Description: >> measurements and return the average value as output data. Each >> value resulted from <type>[_name]_oversampling_ratio measurements >> is considered as one sample for <type>[_name]_sampling_frequency. >> + >> +What: /sys/bus/iio/devices/iio:deviceX/heater_enable >> +KernelVersion: 4.1.0 >> +Contact: linux-iio@xxxxxxxxxxxxxxx >> +Description: >> + A '1' (enable) or '0' (disable) specifying the enable >> + of heater function. Same reading values apply >> + This ABI is especially applicable for humidity sensors >> + to heatup the device and get rid of any condensation >> + in some humidity environment >> diff --git a/drivers/iio/humidity/Kconfig b/drivers/iio/humidity/Kconfig >> index 688c0d1..3fab60c 100644 >> --- a/drivers/iio/humidity/Kconfig >> +++ b/drivers/iio/humidity/Kconfig >> @@ -12,6 +12,17 @@ config DHT11 >> Other sensors should work as well as long as they speak the >> same protocol. >> >> +config HTU21 >> + tristate "Measurement Specialties HTU21 humidity & temperature sensor" >> + depends on I2C >> + select IIO_MS_SENSORS_I2C >> + help >> + If you say yes here you get support for the Measurement Specialties >> + HTU21 humidity and temperature sensor. >> + >> + This driver can also be built as a module. If so, the module will >> + be called htu21. >> + >> config SI7005 >> tristate "SI7005 relative humidity and temperature sensor" >> depends on I2C >> diff --git a/drivers/iio/humidity/Makefile b/drivers/iio/humidity/Makefile >> index 86e2d26..826b1d5 100644 >> --- a/drivers/iio/humidity/Makefile >> +++ b/drivers/iio/humidity/Makefile >> @@ -3,5 +3,6 @@ >> # >> >> obj-$(CONFIG_DHT11) += dht11.o >> +obj-$(CONFIG_HTU21) += htu21.o >> obj-$(CONFIG_SI7005) += si7005.o >> obj-$(CONFIG_SI7020) += si7020.o >> diff --git a/drivers/iio/humidity/htu21.c b/drivers/iio/humidity/htu21.c >> new file mode 100644 >> index 0000000..4406b61 >> --- /dev/null >> +++ b/drivers/iio/humidity/htu21.c >> @@ -0,0 +1,226 @@ >> +/* >> + * htu21.c - Support for Measurement-Specialties >> + * htu21 temperature & humidity sensor >> + * >> + * Copyright (c) 2014 Measurement-Specialties >> + * >> + * Licensed under the GPL-2. >> + * >> + * (7-bit I2C slave address 0x40) >> + * >> + * Datasheet: >> + * http://www.meas-spec.com/downloads/HTU21D.pdf >> + */ >> + >> +#include <linux/init.h> >> +#include <linux/device.h> >> +#include <linux/kernel.h> >> +#include <linux/stat.h> >> +#include <linux/module.h> >> +#include <linux/iio/iio.h> >> +#include <linux/iio/sysfs.h> >> + >> +#include "../common/ms_sensors/ms_sensors_i2c.h" >> + >> +#define HTU21_RESET 0xFE >> + >> +static const int htu21_samp_freq[4] = { 20, 40, 70, 120 }; >> +/* String copy of the above const for readability purpose */ >> +static const char htu21_show_samp_freq[] = "20 40 70 120"; >> + >> +static int htu21_read_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *channel, int *val, >> + int *val2, long mask) >> +{ >> + int ret, temperature; >> + unsigned int humidity; >> + struct ms_ht_dev *dev_data = iio_priv(indio_dev); >> + >> + switch (mask) { >> + case IIO_CHAN_INFO_PROCESSED: >> + switch (channel->type) { >> + case IIO_TEMP: /* in milli °C */ >> + ret = ms_sensors_ht_read_temperature(dev_data, >> + &temperature); >> + if (ret) >> + return ret; >> + *val = temperature; >> + >> + return IIO_VAL_INT; >> + case IIO_HUMIDITYRELATIVE: /* in milli %RH */ >> + ret = ms_sensors_ht_read_humidity(dev_data, >> + &humidity); >> + if (ret) >> + return ret; >> + *val = humidity; >> + >> + return IIO_VAL_INT; >> + default: >> + return -EINVAL; >> + } >> + case IIO_CHAN_INFO_SAMP_FREQ: >> + *val = htu21_samp_freq[dev_data->res_index]; >> + >> + return IIO_VAL_INT; >> + default: >> + return -EINVAL; >> + } >> +} >> + >> +static int htu21_write_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *chan, >> + int val, int val2, long mask) >> +{ >> + struct ms_ht_dev *dev_data = iio_priv(indio_dev); >> + int i, ret; >> + >> + switch (mask) { >> + case IIO_CHAN_INFO_SAMP_FREQ: >> + i = ARRAY_SIZE(htu21_samp_freq); >> + while (i-- > 0) >> + if (val == htu21_samp_freq[i]) >> + break; >> + if (i < 0) >> + return -EINVAL; >> + mutex_lock(&dev_data->lock); >> + dev_data->res_index = i; >> + ret = ms_sensors_write_resolution(dev_data, i); >> + mutex_unlock(&dev_data->lock); >> + >> + return ret; >> + default: >> + return -EINVAL; >> + } >> +} >> + >> +static const struct iio_chan_spec htu21_channels[] = { >> + { >> + .type = IIO_TEMP, >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_PROCESSED), >> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), >> + }, >> + { >> + .type = IIO_HUMIDITYRELATIVE, >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_PROCESSED), >> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), >> + } >> +}; >> + >> +static ssize_t htu21_show_battery_low(struct device *dev, >> + struct device_attribute *attr, char *buf) >> +{ >> + struct iio_dev *indio_dev = dev_to_iio_dev(dev); >> + struct ms_ht_dev *dev_data = iio_priv(indio_dev); >> + >> + return ms_sensors_show_battery_low(dev_data, buf); >> +} >> + >> +static ssize_t htu21_show_heater(struct device *dev, >> + struct device_attribute *attr, char *buf) >> +{ >> + struct iio_dev *indio_dev = dev_to_iio_dev(dev); >> + struct ms_ht_dev *dev_data = iio_priv(indio_dev); >> + >> + return ms_sensors_show_heater(dev_data, buf); >> +} >> + >> +static ssize_t htu21_write_heater(struct device *dev, >> + struct device_attribute *attr, >> + const char *buf, size_t len) >> +{ >> + struct iio_dev *indio_dev = dev_to_iio_dev(dev); >> + struct ms_ht_dev *dev_data = iio_priv(indio_dev); >> + >> + return ms_sensors_write_heater(dev_data, buf, len); >> +} >> + >> +static IIO_CONST_ATTR_SAMP_FREQ_AVAIL(htu21_show_samp_freq); >> +static IIO_DEVICE_ATTR(battery_low, S_IRUGO, >> + htu21_show_battery_low, NULL, 0); >> +static IIO_DEVICE_ATTR(heater_enable, S_IRUGO | S_IWUSR, >> + htu21_show_heater, htu21_write_heater, 0); >> + >> +static struct attribute *htu21_attributes[] = { >> + &iio_const_attr_sampling_frequency_available.dev_attr.attr, >> + &iio_dev_attr_battery_low.dev_attr.attr, >> + &iio_dev_attr_heater_enable.dev_attr.attr, >> + NULL, >> +}; >> + >> +static const struct attribute_group htu21_attribute_group = { >> + .attrs = htu21_attributes, >> +}; >> + >> +static const struct iio_info htu21_info = { >> + .read_raw = htu21_read_raw, >> + .write_raw = htu21_write_raw, >> + .attrs = &htu21_attribute_group, >> + .driver_module = THIS_MODULE, >> +}; >> + >> +int htu21_probe(struct i2c_client *client, >> + const struct i2c_device_id *id) >> +{ >> + struct ms_ht_dev *dev_data; >> + struct iio_dev *indio_dev; >> + int ret; >> + u64 serial_number; >> + >> + if (!i2c_check_functionality(client->adapter, >> + I2C_FUNC_SMBUS_WRITE_BYTE_DATA | >> + I2C_FUNC_SMBUS_WRITE_BYTE | >> + I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { >> + dev_err(&client->dev, >> + "Adapter does not support some i2c transaction\n"); >> + return -ENODEV; >> + } >> + >> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*dev_data)); >> + if (!indio_dev) >> + return -ENOMEM; >> + >> + dev_data = iio_priv(indio_dev); >> + dev_data->client = client; >> + dev_data->res_index = 0; >> + mutex_init(&dev_data->lock); >> + >> + indio_dev->info = &htu21_info; >> + indio_dev->name = id->name; >> + indio_dev->dev.parent = &client->dev; >> + indio_dev->modes = INDIO_DIRECT_MODE; >> + indio_dev->channels = htu21_channels; >> + indio_dev->num_channels = ARRAY_SIZE(htu21_channels); >> + >> + i2c_set_clientdata(client, indio_dev); >> + >> + ret = ms_sensors_reset(client, HTU21_RESET, 15000); >> + if (ret) >> + return ret; >> + >> + ret = ms_sensors_read_serial(client, &serial_number); >> + if (ret) >> + return ret; >> + dev_info(&client->dev, "Serial number : %llx", serial_number); >> + >> + return devm_iio_device_register(&client->dev, indio_dev); >> +} >> + >> +static const struct i2c_device_id htu21_id[] = { >> + {"htu21", 0}, >> + {} >> +}; >> + >> +static struct i2c_driver htu21_driver = { >> + .probe = htu21_probe, >> + .id_table = htu21_id, >> + .driver = { >> + .name = "htu21", >> + }, >> +}; >> + >> +module_i2c_driver(htu21_driver); >> + >> +MODULE_DESCRIPTION("Measurement-Specialties htu21 temperature and humidity driver"); >> +MODULE_AUTHOR("William Markezana <william.markezana@xxxxxxxxxxxxx>"); >> +MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>"); >> +MODULE_LICENSE("GPL v2"); >> > > -- > To unsubscribe from this list: send the line "unsubscribe linux-iio" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html