On 16/07/15 09:10, Peter Meerwald wrote:
>
>> Few notes on the content.
>> - HTU21 is already present in hwmon, however all the features wished by
>> Meas-Spec and the reuse between other HW makes that I have added a new one in
>> iio. Should the hwmon be removed in that case ?
>> - There are things that can be commonalized with drivers ms5611/ms5607 pushed
>> by Thomas. The proposal is to have this done once this patch is approved.
>> - The HW resolution when configurable can be modified using SAMPLE_FREQ channel
>> as requested to avoid private ABI.
>> - Summary on HW :
>> TSYS01 : I2C / SPI - Temp sensor (only I2C supported in this patch)
>> TSYS02D : I2C only - Temp sensor
>> HTU21 : I2C only - Temp & Humidity (T part common with TSYS02D)
>> MS5637 : I2C only - Temp & Pressure
>> MS8607 : I2C only - Temp, Pressure & Humidity sensor (T&P part comon with MS563$
>
> pretty cool, some comments inline below
>
> please check the ABI document (Documentation/ABI/testing/sysfs-bus-iio) I
> think some units might be wrong
>
> the ABI does not mention _processed at all,
That's a quirk of naming when we were actively matching hwmon back at the beginning.
Channels that are 'processed' have attributes with a _input suffix (which is comic
for outputs). Sadly as we can't change existing ABI (well not easily) we are kind
of stuck with this situation.
> but I guess
> in_something_processed should have the same unit as
> specified for in_something_raw (after application of offset and scale)
>
>> Signed-off-by: Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>
>> ---
>> drivers/iio/common/Kconfig | 1 +
>> drivers/iio/common/Makefile | 1 +
>> drivers/iio/common/ms_sensors/Kconfig | 6 +
>> drivers/iio/common/ms_sensors/Makefile | 5 +
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c | 496 +++++++++++++++++++++++++
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.h | 59 +++
>> drivers/iio/humidity/Kconfig | 11 +
>> drivers/iio/humidity/Makefile | 1 +
>> drivers/iio/humidity/htu21.c | 237 ++++++++++++
>> drivers/iio/pressure/Kconfig | 22 ++
>> drivers/iio/pressure/Makefile | 2 +
>> drivers/iio/pressure/ms5637.c | 189 ++++++++++
>> drivers/iio/pressure/ms8607.c | 330 ++++++++++++++++
>> drivers/iio/temperature/Kconfig | 30 ++
>> drivers/iio/temperature/Makefile | 3 +
>> drivers/iio/temperature/tsys01.c | 191 ++++++++++
>> drivers/iio/temperature/tsys01.h | 43 +++
>> drivers/iio/temperature/tsys01_i2c.c | 67 ++++
>> drivers/iio/temperature/tsys02d.c | 206 ++++++++++
>> 19 files changed, 1900 insertions(+)
>> create mode 100644 drivers/iio/common/ms_sensors/Kconfig
>> create mode 100644 drivers/iio/common/ms_sensors/Makefile
>> create mode 100644 drivers/iio/common/ms_sensors/ms_sensors_i2c.c
>> create mode 100644 drivers/iio/common/ms_sensors/ms_sensors_i2c.h
>> create mode 100644 drivers/iio/humidity/htu21.c
>> create mode 100644 drivers/iio/pressure/ms5637.c
>> create mode 100644 drivers/iio/pressure/ms8607.c
>> create mode 100644 drivers/iio/temperature/tsys01.c
>> create mode 100644 drivers/iio/temperature/tsys01.h
>> create mode 100644 drivers/iio/temperature/tsys01_i2c.c
>> create mode 100644 drivers/iio/temperature/tsys02d.c
>>
>> diff --git a/drivers/iio/common/Kconfig b/drivers/iio/common/Kconfig
>> index 790f106..26a6026 100644
>> --- a/drivers/iio/common/Kconfig
>> +++ b/drivers/iio/common/Kconfig
>> @@ -3,5 +3,6 @@
>> #
>>
>> source "drivers/iio/common/hid-sensors/Kconfig"
>> +source "drivers/iio/common/ms_sensors/Kconfig"
>> source "drivers/iio/common/ssp_sensors/Kconfig"
>> source "drivers/iio/common/st_sensors/Kconfig"
>> diff --git a/drivers/iio/common/Makefile b/drivers/iio/common/Makefile
>> index b1e4d9c..585da6a 100644
>> --- a/drivers/iio/common/Makefile
>> +++ b/drivers/iio/common/Makefile
>> @@ -8,5 +8,6 @@
>>
>> # When adding new entries keep the list in alphabetical order
>> obj-y += hid-sensors/
>> +obj-y += ms_sensors/
>> obj-y += ssp_sensors/
>> obj-y += st_sensors/
>> diff --git a/drivers/iio/common/ms_sensors/Kconfig b/drivers/iio/common/ms_sensors/Kconfig
>> new file mode 100644
>> index 0000000..b28a92b
>> --- /dev/null
>> +++ b/drivers/iio/common/ms_sensors/Kconfig
>> @@ -0,0 +1,6 @@
>> +#
>> +# Measurements Specialties sensors common library
>> +#
>> +
>> +config IIO_MS_SENSORS_I2C
>> + tristate
>> diff --git a/drivers/iio/common/ms_sensors/Makefile b/drivers/iio/common/ms_sensors/Makefile
>> new file mode 100644
>> index 0000000..7846428
>> --- /dev/null
>> +++ b/drivers/iio/common/ms_sensors/Makefile
>> @@ -0,0 +1,5 @@
>> +#
>> +# Makefile for the Measurement Specialties sensor common modules.
>> +#
>> +
>> +obj-$(CONFIG_IIO_MS_SENSORS_I2C) += ms_sensors_i2c.o
>> diff --git a/drivers/iio/common/ms_sensors/ms_sensors_i2c.c b/drivers/iio/common/ms_sensors/ms_sensors_i2c.c
>> new file mode 100644
>> index 0000000..a79ea48
>> --- /dev/null
>> +++ b/drivers/iio/common/ms_sensors/ms_sensors_i2c.c
>> @@ -0,0 +1,496 @@
>> +/*
>> + * Measurements Specialties driver common i2c functions
>> + *
>> + * Copyright (c) 2015 Measurement-Specialties
>> + *
>> + * Licensed under the GPL-2.
>> + *
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/iio/iio.h>
>> +#include <linux/device.h>
>> +#include <linux/delay.h>
>> +
>> +#include "ms_sensors_i2c.h"
>> +
>> +static const u16 ms_sensors_ht_t_conversion_time[] = { 50000, 25000,
>> + 13000, 7000 };
>
> I'd appreciate a comment indicating the time unit
>
>> +static const u16 ms_sensors_ht_h_conversion_time[] = { 16000, 3000,
>> + 5000, 8000 };
>> +static const u16 ms_sensors_tp_conversion_time[] = { 500, 1100, 2100,
>> + 4100, 8220, 16440 };
>> +
>> +#define MS_SENSORS_SERIAL_READ_MSB 0xFA0F
>> +#define MS_SENSORS_SERIAL_READ_LSB 0xFCC9
>> +#define MS_SENSORS_USER_REG_WRITE 0xE6
>> +#define MS_SENSORS_USER_REG_READ 0xE7
>> +#define MS_SENSORS_HT_T_CONVERSION_START 0xF3
>> +#define MS_SENSORS_HT_H_CONVERSION_START 0xF5
>> +
>> +#define MS_SENSORS_TP_PROM_READ 0xA0
>> +#define MS_SENSORS_TP_T_CONVERSION_START 0x50
>> +#define MS_SENSORS_TP_P_CONVERSION_START 0x40
>> +#define MS_SENSORS_TP_ADC_READ 0x00
>> +
>> +#define MS_SENSORS_NO_READ_CMD 0xFF
>> +
>> +int ms_sensors_i2c_reset(void *cli, u8 cmd, unsigned int delay)
>> +{
>> + int ret;
>> + struct i2c_client *client = cli;
>> +
>> + ret = i2c_smbus_write_byte(client, cmd);
>> + if (ret) {
>> + dev_err(&client->dev, "Failed to reset device\n");
>> + return ret;
>> + }
>> + usleep_range(delay, delay + 1000);
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_reset);
>> +
>> +int ms_sensors_i2c_read_prom_word(void *cli, int cmd, u16 *word)
>> +{
>> + int ret;
>> + struct i2c_client *client = (struct i2c_client *)cli;
>> +
>> + ret = i2c_smbus_read_word_swapped(client, cmd);
>> + if (ret < 0) {
>> + dev_err(&client->dev, "Failed to read prom word\n");
>> + return ret;
>> + }
>> + *word = ret;
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_read_prom_word);
>> +
>> +int ms_sensors_i2c_convert_and_read(void *cli, u8 conv, u8 rd,
>> + unsigned int delay, u32 *adc)
>> +{
>> + int ret;
>> + u32 buf = 0;
>> + struct i2c_client *client = (struct i2c_client *)cli;
>> +
>> + /* Trigger conversion */
>> + ret = i2c_smbus_write_byte(client, conv);
>> + if (ret)
>> + goto err;
>> + usleep_range(delay, delay + 1000);
>> +
>> + /* Retrieve ADC value */
>> + if (rd != MS_SENSORS_NO_READ_CMD)
>> + ret = i2c_smbus_read_i2c_block_data(client, rd, 3, (u8 *)&buf);
>> + else
>> + ret = i2c_master_recv(client, (u8 *)&buf, 3);
>> + if (ret < 0)
>> + goto err;
>> +
>> + dev_dbg(&client->dev, "ADC raw value : %x\n", cpu_to_be32(buf) >> 8);
>
> be32_to_cpu() would make more sense to me; the device provides the data in
> be32 and we need it in cpu endianness; cpu_to_be32() seems backwards
>
>> + *adc = cpu_to_be32(buf) >> 8;
>> +
>> + return 0;
>> +err:
>> + dev_err(&client->dev, "Unable to make sensor adc conversion\n");
>> + return ret;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_convert_and_read);
>> +
>> +static bool ms_sensors_crc_valid(u32 value)
>> +{
>> + u32 polynom = 0x988000; /* x^8 + x^5 + x^4 + 1 */
>> + u32 msb = 0x800000;
>> + u32 mask = 0xFF8000;
>> + u32 result = value & 0xFFFF00;
>> + u8 crc = value & 0xFF;
>> +
>> + while (msb != 0x80) {
>> + if (result & msb)
>> + result = ((result ^ polynom) & mask)
>> + | (result & ~mask);
>> + msb >>= 1;
>> + mask >>= 1;
>> + polynom >>= 1;
>> + }
>> +
>> + return result == crc;
>> +}
>> +
>> +int ms_sensors_i2c_read_serial(struct i2c_client *client, u64 *sn)
>> +{
>> + u8 i;
>> + u64 rcv_buf = 0;
>> + u16 send_buf;
>> + int ret;
>> +
>> + struct i2c_msg msg[2] = {
>> + {
>> + .addr = client->addr,
>> + .flags = client->flags,
>> + .len = 2,
>> + .buf = (char *)&send_buf,
>> + },
>> + {
>> + .addr = client->addr,
>> + .flags = client->flags | I2C_M_RD,
>> + .buf = (char *)&rcv_buf,
>> + },
>> + };
>> +
>> + /* Read MSB part of serial number */
>> + send_buf = be16_to_cpu(MS_SENSORS_SERIAL_READ_MSB);
>
> cpu_to_be16()?
>
>> + msg[1].len = 8;
>> + ret = i2c_transfer(client->adapter, msg, 2);
>> + if (ret < 0)
>> + goto err;
>> +
>> + rcv_buf = cpu_to_be64(rcv_buf);
>> + dev_dbg(&client->dev, "Serial MSB raw : %llx\n", rcv_buf);
>> +
>> + for (i = 0; i < 64; i += 16) {
>> + if (!ms_sensors_crc_valid((rcv_buf >> i) & 0xFFFF))
>> + return -ENODEV;
>> + }
>> +
>> + *sn = (((rcv_buf >> 32) & 0xFF000000) |
>> + ((rcv_buf >> 24) & 0x00FF0000) |
>> + ((rcv_buf >> 16) & 0x0000FF00) |
>> + ((rcv_buf >> 8) & 0x000000FF)) << 16;
>> +
>> + /* Read LSB part of serial number */
>> + send_buf = be16_to_cpu(MS_SENSORS_SERIAL_READ_LSB);
>> + msg[1].len = 6;
>> + rcv_buf = 0;
>> + ret = i2c_transfer(client->adapter, msg, 2);
>> + if (ret < 0)
>> + goto err;
>> +
>> + rcv_buf = cpu_to_be64(rcv_buf) >> 16;
>> + dev_dbg(&client->dev, "Serial MSB raw : %llx\n", rcv_buf);
>> +
>> + for (i = 0; i < 48; i += 24) {
>> + if (!ms_sensors_crc_valid((rcv_buf >> i) & 0xFFFFFF))
>> + return -ENODEV;
>> + }
>> +
>> + *sn |= (rcv_buf & 0xFFFF00) << 40 | (rcv_buf >> 32);
>> +
>> + return 0;
>> +
>> +err:
>> + dev_err(&client->dev, "Unable to read device serial number");
>> + return ret;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_read_serial);
>> +
>> +static int ms_sensors_i2c_read_user_reg(struct i2c_client *client,
>> + u8 *user_reg)
>> +{
>> + int ret;
>> +
>> + ret = i2c_smbus_write_byte(client, MS_SENSORS_USER_REG_READ);
>> + if (ret)
>> + goto err;
>> +
>> + ret = i2c_master_recv(client, user_reg, 1);
>> + if (ret < 0)
>> + goto err;
>> + dev_dbg(&client->dev, "User register :%x\n", *user_reg);
>> +
>> + return 0;
>> +err:
>> + dev_err(&client->dev, "Unable to read user reg");
>> + return ret;
>> +}
>> +
>> +ssize_t ms_sensors_i2c_write_resolution(struct ms_ht_dev *dev_data,
>> + u8 i)
>> +{
>> + u8 user_reg;
>> + int ret;
>> +
>> + ret = ms_sensors_i2c_read_user_reg(dev_data->client, &user_reg);
>> + if (ret)
>> + return ret;
>> +
>> + user_reg &= 0x7E;
>> + user_reg |= ((i & 1) << 7) + ((i & 2) >> 1);
>> +
>> + ret = i2c_smbus_write_byte_data(dev_data->client,
>> + MS_SENSORS_USER_REG_WRITE,
>> + user_reg);
>> +
>
> return directly w/o assigning to ret
>
>> + return ret;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_write_resolution);
>> +
>> +ssize_t ms_sensors_i2c_show_serial(struct ms_ht_dev *dev_data, char *buf)
>> +{
>> + int ret = sprintf(buf, "%08llx\n", dev_data->serial_number);
>> +
>
> same here
>
>> + return ret;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_show_serial);
>> +
>> +ssize_t ms_sensors_i2c_show_battery_low(struct ms_ht_dev *dev_data,
>> + char *buf)
>> +{
>> + int ret;
>> + u8 user_reg;
>> +
>> + mutex_lock(&dev_data->lock);
>> + ret = ms_sensors_i2c_read_user_reg(dev_data->client, &user_reg);
>> + mutex_unlock(&dev_data->lock);
>> + if (ret)
>> + return ret;
>> +
>> + return sprintf(buf, "%d\n", (user_reg & 0x40) >> 6);
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_show_battery_low);
>> +
>> +ssize_t ms_sensors_i2c_show_heater(struct ms_ht_dev *dev_data,
>> + char *buf)
>> +{
>> + u8 user_reg;
>> + int ret;
>> +
>> + mutex_lock(&dev_data->lock);
>> + ret = ms_sensors_i2c_read_user_reg(dev_data->client, &user_reg);
>> + mutex_unlock(&dev_data->lock);
>> + if (ret)
>> + return ret;
>> +
>> + return sprintf(buf, "%d\n", (user_reg & 0x4) >> 2);
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_show_heater);
>> +
>> +ssize_t ms_sensors_i2c_write_heater(struct ms_ht_dev *dev_data,
>> + const char *buf, size_t len)
>> +{
>> + u8 val, user_reg;
>> + int ret;
>> +
>> + ret = kstrtou8(buf, 10, &val);
>> + if (ret)
>> + return ret;
>> +
>> + if (val > 1)
>> + return -EINVAL;
>> +
>> + mutex_lock(&dev_data->lock);
>> + ret = ms_sensors_i2c_read_user_reg(dev_data->client, &user_reg);
>> + if (ret) {
>> + mutex_unlock(&dev_data->lock);
>> + return ret;
>> + }
>> +
>> + user_reg &= 0xFB;
>> + user_reg |= val << 2;
>> +
>> + ret = i2c_smbus_write_byte_data(dev_data->client,
>> + MS_SENSORS_USER_REG_WRITE,
>> + user_reg);
>> + mutex_unlock(&dev_data->lock);
>> + if (ret) {
>> + dev_err(&dev_data->client->dev, "Unable to write user reg\n");
>> + return ret;
>> + }
>> +
>> + return len;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_write_heater);
>> +
>> +int ms_sensors_i2c_ht_read_temperature(struct ms_ht_dev *dev_data,
>> + s32 *temperature)
>> +{
>> + int ret;
>> + u32 adc;
>> + u16 delay;
>> +
>> + mutex_lock(&dev_data->lock);
>> + delay = ms_sensors_ht_t_conversion_time[dev_data->res_index];
>> + ret = ms_sensors_i2c_convert_and_read(dev_data->client,
>> + MS_SENSORS_HT_T_CONVERSION_START,
>> + MS_SENSORS_NO_READ_CMD,
>> + delay, &adc);
>> + mutex_unlock(&dev_data->lock);
>> + if (ret)
>> + return ret;
>> +
>> + if (!ms_sensors_crc_valid(adc)) {
>> + dev_err(&dev_data->client->dev,
>> + "Temperature read crc check error\n");
>> + return -ENODEV;
>> + }
>> +
>> + /* Temperature algorithm */
>> + *temperature = (((s64)(adc >> 8) * 175720) >> 16) - 46850;
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_ht_read_temperature);
>> +
>> +int ms_sensors_i2c_ht_read_humidity(struct ms_ht_dev *dev_data,
>> + u32 *humidity)
>> +{
>> + int ret;
>> + u32 adc;
>> + u16 delay;
>> +
>> + mutex_lock(&dev_data->lock);
>> + delay = ms_sensors_ht_h_conversion_time[dev_data->res_index];
>> + ret = ms_sensors_i2c_convert_and_read(dev_data->client,
>> + MS_SENSORS_HT_H_CONVERSION_START,
>> + MS_SENSORS_NO_READ_CMD,
>> + delay, &adc);
>> + mutex_unlock(&dev_data->lock);
>> + if (ret)
>> + return ret;
>> +
>> + if (!ms_sensors_crc_valid(adc)) {
>> + dev_err(&dev_data->client->dev,
>> + "Humidity read crc check error\n");
>> + return -ENODEV;
>> + }
>> +
>> + /* Humidity algorithm */
>> + *humidity = (((s32)(adc >> 8) * 12500) >> 16) - 600;
>> + if (*humidity >= 10000)
>> + *humidity = 10000;
>
> IIO relative humidity should be in milli percent; what is the max value
> exposed to userspace
>
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_i2c_ht_read_humidity);
>> +
>> +static bool ms_sensors_tp_crc_valid(u16 *prom, u8 len)
>> +{
>> + unsigned int cnt, n_bit;
>> + u16 n_rem = 0x0000, crc_read = prom[0], crc = (*prom & 0xF000) >> 12;
>> +
>> + prom[len - 1] = 0;
>> + prom[0] &= 0x0FFF; /* Clear the CRC computation part */
>> +
>> + for (cnt = 0; cnt < len * 2; cnt++) {
>> + if (cnt % 2 == 1)
>> + n_rem ^= prom[cnt >> 1] & 0x00FF;
>> + else
>> + n_rem ^= prom[cnt >> 1] >> 8;
>> +
>> + for (n_bit = 8; n_bit > 0; n_bit--) {
>> + if (n_rem & 0x8000)
>> + n_rem = (n_rem << 1) ^ 0x3000;
>> + else
>> + n_rem <<= 1;
>> + }
>> + }
>> + n_rem >>= 12;
>> + prom[0] = crc_read;
>> +
>> + return n_rem == crc;
>> +}
>> +
>> +int ms_sensors_tp_read_prom(struct ms_tp_dev *dev_data)
>> +{
>> + int i, ret;
>> +
>> + for (i = 0; i < MS_SENSORS_TP_PROM_WORDS_NB; i++) {
>> + ret = ms_sensors_i2c_read_prom_word(
>> + dev_data->client,
>> + MS_SENSORS_TP_PROM_READ + (i << 1),
>> + &dev_data->prom[i]);
>> +
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + if (!ms_sensors_tp_crc_valid(dev_data->prom,
>> + MS_SENSORS_TP_PROM_WORDS_NB + 1)) {
>> + dev_err(&dev_data->client->dev,
>> + "Calibration coefficients crc check error\n");
>> + return -ENODEV;
>> + }
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_tp_read_prom);
>> +
>> +int ms_sensors_read_temp_and_pressure(struct ms_tp_dev *dev_data,
>> + int *temperature,
>> + unsigned int *pressure)
>> +{
>> + int ret;
>> + u32 t_adc, p_adc;
>> + s32 dt, temp;
>> + s64 off, sens, t2, off2, sens2;
>> + u16 *prom = dev_data->prom, delay;
>> + u8 i;
>> +
>> + mutex_lock(&dev_data->lock);
>> + i = dev_data->res_index * 2;
>> + delay = ms_sensors_tp_conversion_time[dev_data->res_index];
>> + ret = ms_sensors_i2c_convert_and_read(
>> + dev_data->client,
>> + MS_SENSORS_TP_T_CONVERSION_START + i,
>> + MS_SENSORS_TP_ADC_READ,
>> + delay, &t_adc);
>> + if (ret) {
>> + mutex_unlock(&dev_data->lock);
>> + return ret;
>> + }
>> + ret = ms_sensors_i2c_convert_and_read(
>> + dev_data->client,
>> + MS_SENSORS_TP_P_CONVERSION_START + i,
>> + MS_SENSORS_TP_ADC_READ,
>> + delay, &p_adc);
>> + mutex_unlock(&dev_data->lock);
>> + if (ret)
>> + return ret;
>> +
>> + dt = (s32)t_adc - (prom[5] << 8);
>> +
>> + /* Actual temperature = 2000 + dT * TEMPSENS */
>> + temp = 2000 + (((s64)dt * prom[6]) >> 23);
>> +
>> + /* Second order temperature compensation */
>> + if (temp < 2000) {
>> + s64 tmp = (s64)temp - 2000;
>> +
>> + t2 = (3 * ((s64)dt * (s64)dt)) >> 33;
>> + off2 = (61 * tmp * tmp) >> 4;
>> + sens2 = (29 * tmp * tmp) >> 4;
>> +
>> + if (temp < -1500) {
>> + s64 tmp = (s64)temp + 1500;
>> +
>> + off2 += 17 * tmp * tmp;
>> + sens2 += 9 * tmp * tmp;
>> + }
>> + } else {
>> + t2 = (5 * ((s64)dt * (s64)dt)) >> 38;
>> + off2 = 0;
>> + sens2 = 0;
>> + }
>> +
>> + /* OFF = OFF_T1 + TCO * dT */
>> + off = (((s64)prom[2]) << 17) + ((((s64)prom[4]) * (s64)dt) >> 6);
>> + off -= off2;
>> +
>> + /* Sensitivity at actual temperature = SENS_T1 + TCS * dT */
>> + sens = (((s64)prom[1]) << 16) + (((s64)prom[3] * dt) >> 7);
>> + sens -= sens2;
>> +
>> + /* Temperature compensated pressure = D1 * SENS - OFF */
>> + *temperature = (temp - t2) * 10;
>> + *pressure = (u32)(((((s64)p_adc * sens) >> 21) - off) >> 15);
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL(ms_sensors_read_temp_and_pressure);
>> +
>> +MODULE_DESCRIPTION("Measurement-Specialties common i2c driver");
>> +MODULE_AUTHOR("William Markezana <william.markezana@xxxxxxxxxxxxx>");
>> +MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>");
>> +MODULE_LICENSE("GPL v2");
>> +
>> diff --git a/drivers/iio/common/ms_sensors/ms_sensors_i2c.h b/drivers/iio/common/ms_sensors/ms_sensors_i2c.h
>> new file mode 100644
>> index 0000000..45e49ed
>> --- /dev/null
>> +++ b/drivers/iio/common/ms_sensors/ms_sensors_i2c.h
>> @@ -0,0 +1,59 @@
>> +/*
>> + * Measurements Specialties common sensor driver
>> + *
>> + * Copyright (c) 2015 Measurement-Specialties
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + *
>> + */
>> +
>> +#ifndef _MS_SENSORS_I2C_H
>> +#define _MS_SENSORS_I2C_H
>> +
>> +#include <linux/i2c.h>
>> +#include <linux/mutex.h>
>> +
>> +#define MS_SENSORS_TP_PROM_WORDS_NB 7
>> +
>> +#define MS_SENSORS_ATTR_SERIAL 0
>> +#define MS_SENSORS_ATTR_BAT 1
>> +#define MS_SENSORS_ATTR_HEATER 2
>> +
>> +struct ms_ht_dev {
>> + struct i2c_client *client;
>> + struct mutex lock; /* mutex protecting data structure */
>> + u64 serial_number;
>> + u8 res_index;
>> +};
>> +
>> +struct ms_tp_dev {
>> + struct i2c_client *client;
>> + struct mutex lock; /* mutex protecting data structure */
>> + /* Added element for CRC computation */
>> + u16 prom[MS_SENSORS_TP_PROM_WORDS_NB + 1];
>> + u8 res_index;
>> +};
>> +
>> +int ms_sensors_i2c_reset(void *cli, u8 cmd, unsigned int delay);
>> +int ms_sensors_i2c_read_prom_word(void *cli, int cmd, u16 *word);
>> +int ms_sensors_i2c_convert_and_read(void *cli, u8 conv, u8 rd,
>> + unsigned int delay, u32 *adc);
>> +int ms_sensors_i2c_read_serial(struct i2c_client *client, u64 *sn);
>> +ssize_t ms_sensors_i2c_show_serial(struct ms_ht_dev *dev_data, char *buf);
>> +ssize_t ms_sensors_i2c_write_resolution(struct ms_ht_dev *dev_data, u8 i);
>> +ssize_t ms_sensors_i2c_show_battery_low(struct ms_ht_dev *dev_data, char *buf);
>> +ssize_t ms_sensors_i2c_show_heater(struct ms_ht_dev *dev_data, char *buf);
>> +ssize_t ms_sensors_i2c_write_heater(struct ms_ht_dev *dev_data,
>> + const char *buf, size_t len);
>> +int ms_sensors_i2c_ht_read_temperature(struct ms_ht_dev *dev_data,
>> + s32 *temperature);
>> +int ms_sensors_i2c_ht_read_humidity(struct ms_ht_dev *dev_data,
>> + u32 *humidity);
>> +int ms_sensors_tp_read_prom(struct ms_tp_dev *dev_data);
>> +int ms_sensors_read_temp_and_pressure(struct ms_tp_dev *dev_data,
>> + int *temperature,
>> + unsigned int *pressure);
>> +
>> +#endif /* _MS_SENSORS_I2C_H */
>> diff --git a/drivers/iio/humidity/Kconfig b/drivers/iio/humidity/Kconfig
>> index 4813b79..ccb2de3 100644
>> --- a/drivers/iio/humidity/Kconfig
>> +++ b/drivers/iio/humidity/Kconfig
>> @@ -12,6 +12,17 @@ config DHT11
>> Other sensors should work as well as long as they speak the
>> same protocol.
>>
>> +config HTU21
>> + tristate "Measurement Specialities HTU21 humidity & temperature sensor"
>
> Specialties
>
>> + depends on I2C
>> + select IIO_MS_SENSORS_I2C
>> + help
>> + If you say yes here you get support for the Measurement Specialties
>> + HTU21 humidity and temperature sensor.
>> +
>> + This driver can also be built as a module. If so, the module will
>> + be called htu21.
>> +
>> config SI7005
>> tristate "SI7005 relative humidity and temperature sensor"
>> depends on I2C
>> diff --git a/drivers/iio/humidity/Makefile b/drivers/iio/humidity/Makefile
>> index 86e2d26..826b1d5 100644
>> --- a/drivers/iio/humidity/Makefile
>> +++ b/drivers/iio/humidity/Makefile
>> @@ -3,5 +3,6 @@
>> #
>>
>> obj-$(CONFIG_DHT11) += dht11.o
>> +obj-$(CONFIG_HTU21) += htu21.o
>> obj-$(CONFIG_SI7005) += si7005.o
>> obj-$(CONFIG_SI7020) += si7020.o
>> diff --git a/drivers/iio/humidity/htu21.c b/drivers/iio/humidity/htu21.c
>> new file mode 100644
>> index 0000000..1efc291
>> --- /dev/null
>> +++ b/drivers/iio/humidity/htu21.c
>> @@ -0,0 +1,237 @@
>> +/*
>> + * htu21.c - Support for Measurement-Specialties
>> + * htu21 temperature & humidity sensor
>> + *
>> + * Copyright (c) 2014 Measurement-Specialties
>> + *
>> + * Licensed under the GPL-2.
>> + *
>> + * (7-bit I2C slave address 0x40)
>> + *
>> + * Datasheet:
>> + * http://www.meas-spec.com/downloads/HTU21D.pdf
>> + *
>> + */
>> +
>> +#include <linux/init.h>
>> +#include <linux/device.h>
>> +#include <linux/kernel.h>
>> +#include <linux/stat.h>
>> +#include <linux/module.h>
>> +#include <linux/iio/iio.h>
>> +#include <linux/iio/sysfs.h>
>> +
>> +#include "../common/ms_sensors/ms_sensors_i2c.h"
>> +
>> +#define HTU21_RESET 0xFE
>> +
>> +static const int htu21_samp_freq[4] = { 20, 40, 70, 120 };
>> +/* String copy of the above const for readability purpose */
>> +static const char htu21_show_samp_freq[] = "20 40 70 120";
>> +
>> +static int htu21_read_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *channel, int *val,
>> + int *val2, long mask)
>> +{
>> + int ret, temperature;
>> + unsigned int humidity;
>> + struct ms_ht_dev *dev_data = iio_priv(indio_dev);
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_PROCESSED:
>> + switch (channel->type) {
>> + case IIO_TEMP: /* in °C */
>
> should be in milli °C
>
>> + ret = ms_sensors_i2c_ht_read_temperature(dev_data,
>> + &temperature);
>> + if (ret)
>> + return ret;
>> + *val = temperature / 1000;
>> + *val2 = (temperature % 1000) * 1000;
>> +
>> + return IIO_VAL_INT_PLUS_MICRO;
>> + case IIO_HUMIDITYRELATIVE: /* in %RH */
>
> should be in milli %
>
>> + ret = ms_sensors_i2c_ht_read_humidity(dev_data,
>> + &humidity);
>> + if (ret)
>> + return ret;
>> + *val = humidity / 100;
>> + *val2 = (humidity % 100) * 10000;
>> +
>> + return IIO_VAL_INT_PLUS_MICRO;
>> + default:
>> + return -EINVAL;
>> + }
>> + case IIO_CHAN_INFO_SAMP_FREQ:
>> + *val = htu21_samp_freq[dev_data->res_index];
>> +
>> + return IIO_VAL_INT;
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static int htu21_write_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *chan,
>> + int val, int val2, long mask)
>> +{
>> + struct ms_ht_dev *dev_data = iio_priv(indio_dev);
>> + int i, ret;
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_SAMP_FREQ:
>> + i = ARRAY_SIZE(htu21_samp_freq);
>> + while (i-- > 0)
>> + if (val == htu21_samp_freq[i])
>> + break;
>> + if (i < 0)
>> + return -EINVAL;
>> + mutex_lock(&dev_data->lock);
>> + dev_data->res_index = i;
>> + ret = ms_sensors_i2c_write_resolution(dev_data, i);
>> + mutex_unlock(&dev_data->lock);
>> +
>> + return ret;
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static const struct iio_chan_spec htu21_channels[] = {
>> + {
>> + .type = IIO_TEMP,
>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_PROCESSED),
>> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
>> + },
>> + {
>> + .type = IIO_HUMIDITYRELATIVE,
>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_PROCESSED),
>> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
>> + }
>> +};
>> +
>> +static ssize_t htu21_i2c_write_heater(struct device *dev,
>> + struct device_attribute *attr,
>> + const char *buf, size_t len)
>> +{
>> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
>> + struct ms_ht_dev *dev_data = iio_priv(indio_dev);
>> +
>> + return ms_sensors_i2c_write_heater(dev_data, buf, len);
>> +}
>> +
>> +static ssize_t htu21_attr_read(struct device *dev,
>> + struct device_attribute *attr, char *buf)
>> +{
>> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
>> + struct ms_ht_dev *dev_data = iio_priv(indio_dev);
>> + struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
>> +
>> + switch (this_attr->address) {
>> + case MS_SENSORS_ATTR_SERIAL:
>
> maybe drop newlines here
>
>> +
>> + return ms_sensors_i2c_show_serial(dev_data, buf);
>> + case MS_SENSORS_ATTR_BAT:
>> +
>> + return ms_sensors_i2c_show_battery_low(dev_data, buf);
>> + case MS_SENSORS_ATTR_HEATER:
>> +
>> + return ms_sensors_i2c_show_heater(dev_data, buf);
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static IIO_CONST_ATTR_SAMP_FREQ_AVAIL(htu21_show_samp_freq);
>> +static IIO_DEVICE_ATTR(in_serial, S_IRUGO,
>> + htu21_attr_read, NULL, MS_SENSORS_ATTR_SERIAL);
>> +static IIO_DEVICE_ATTR(in_battery_low, S_IRUGO,
>> + htu21_attr_read, NULL, MS_SENSORS_ATTR_BAT);
>> +static IIO_DEVICE_ATTR(heater_enable,
>> + S_IRUGO | S_IWUSR,
>> + htu21_attr_read,
>> + htu21_i2c_write_heater, MS_SENSORS_ATTR_HEATER);
>> +
>> +static struct attribute *htu21_attributes[] = {
>> + &iio_const_attr_sampling_frequency_available.dev_attr.attr,
>> + &iio_dev_attr_in_serial.dev_attr.attr,
>> + &iio_dev_attr_in_battery_low.dev_attr.attr,
>> + &iio_dev_attr_heater_enable.dev_attr.attr,
>> + NULL,
>> +};
>> +
>> +static const struct attribute_group htu21_attribute_group = {
>> + .attrs = htu21_attributes,
>> +};
>> +
>> +static const struct iio_info htu21_info = {
>> + .read_raw = htu21_read_raw,
>> + .write_raw = htu21_write_raw,
>> + .attrs = &htu21_attribute_group,
>> + .driver_module = THIS_MODULE,
>> +};
>> +
>> +int htu21_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct ms_ht_dev *dev_data;
>> + struct iio_dev *indio_dev;
>> + int ret;
>> +
>> + if (!i2c_check_functionality(client->adapter,
>> + I2C_FUNC_SMBUS_WRITE_BYTE_DATA |
>> + I2C_FUNC_SMBUS_WRITE_BYTE |
>> + I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
>> + dev_err(&client->dev,
>> + "Adapter does not support some transaction\n");
>
> maybe indicate that this related to I2C?
>
>> + return -ENODEV;
>> + }
>> +
>> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*dev_data));
>> + if (!indio_dev)
>> + return -ENOMEM;
>> +
>> + dev_data = iio_priv(indio_dev);
>> + dev_data->client = client;
>> + dev_data->res_index = 0;
>> + mutex_init(&dev_data->lock);
>> +
>> + indio_dev->info = &htu21_info;
>> + indio_dev->name = id->name;
>> + indio_dev->dev.parent = &client->dev;
>> + indio_dev->modes = INDIO_DIRECT_MODE;
>> + indio_dev->channels = htu21_channels;
>> + indio_dev->num_channels = ARRAY_SIZE(htu21_channels);
>> +
>> + i2c_set_clientdata(client, indio_dev);
>> +
>> + ret = ms_sensors_i2c_reset(client, HTU21_RESET, 15000);
>> + if (ret)
>> + return ret;
>> +
>> + ret = ms_sensors_i2c_read_serial(client, &dev_data->serial_number);
>> + if (ret)
>> + return ret;
>> +
>> + return devm_iio_device_register(&client->dev, indio_dev);
>> +}
>> +
>> +static const struct i2c_device_id htu21_id[] = {
>> + {"htu21", 0},
>> + {}
>> +};
>> +
>> +static struct i2c_driver htu21_driver = {
>> + .probe = htu21_probe,
>> + .id_table = htu21_id,
>> + .driver = {
>> + .name = "htu21",
>> + .owner = THIS_MODULE,
>> + },
>> +};
>> +
>> +module_i2c_driver(htu21_driver);
>> +
>> +MODULE_DESCRIPTION("Measurement-Specialties htu21 temperature and humidity driver");
>> +MODULE_AUTHOR("William Markezana <william.markezana@xxxxxxxxxxxxx>");
>> +MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig
>> index fa62950..8108597 100644
>> --- a/drivers/iio/pressure/Kconfig
>> +++ b/drivers/iio/pressure/Kconfig
>> @@ -79,6 +79,28 @@ config MS5611_SPI
>> To compile this driver as a module, choose M here: the module will
>> be called ms5611_spi.
>>
>> +config MS5637
>> + tristate "Measurement Specialities MS5637 pressure & temperature sensor"
>
> Specialties
>
>> + depends on I2C
>> + select IIO_MS_SENSORS_I2C
>> + help
>> + If you say yes here you get support for the Measurement Specialties
>> + MS5637 pressure and temperature sensor.
>> +
>> + This driver can also be built as a module. If so, the module will
>> + be called ms5637.
>> +
>> +config MS8607
>> + tristate "Measurement Specialities MS8607 pressure, temperature & humidity sensor"
>
> Specialties
>
>> + depends on I2C
>> + select IIO_MS_SENSORS_I2C
>> + help
>> + If you say yes here you get support for the Measurement Specialties
>> + MS8607 pressure, temperature and humidity sensor.
>> +
>> + This driver can also be built as a module. If so, the module will
>> + be called ms8607.
>> +
>> config IIO_ST_PRESS
>> tristate "STMicroelectronics pressure sensor Driver"
>> depends on (I2C || SPI_MASTER) && SYSFS
>> diff --git a/drivers/iio/pressure/Makefile b/drivers/iio/pressure/Makefile
>> index a4f98f8..89c9e37 100644
>> --- a/drivers/iio/pressure/Makefile
>> +++ b/drivers/iio/pressure/Makefile
>> @@ -10,6 +10,8 @@ obj-$(CONFIG_MPL3115) += mpl3115.o
>> obj-$(CONFIG_MS5611) += ms5611_core.o
>> obj-$(CONFIG_MS5611_I2C) += ms5611_i2c.o
>> obj-$(CONFIG_MS5611_SPI) += ms5611_spi.o
>> +obj-$(CONFIG_MS5637) += ms5637.o
>> +obj-$(CONFIG_MS8607) += ms8607.o
>> obj-$(CONFIG_IIO_ST_PRESS) += st_pressure.o
>> st_pressure-y := st_pressure_core.o
>> st_pressure-$(CONFIG_IIO_BUFFER) += st_pressure_buffer.o
>> diff --git a/drivers/iio/pressure/ms5637.c b/drivers/iio/pressure/ms5637.c
>> new file mode 100644
>> index 0000000..2f50772
>> --- /dev/null
>> +++ b/drivers/iio/pressure/ms5637.c
>> @@ -0,0 +1,189 @@
>> +/*
>> + * ms5637.c - Support for Measurement-Specialties ms5637
>> + * pressure & temperature sensor
>> + *
>> + * Copyright (c) 2015 Measurement-Specialties
>> + *
>> + * Licensed under the GPL-2.
>> + *
>> + * (7-bit I2C slave address 0x76)
>> + *
>> + * Datasheet:
>> + * http://www.meas-spec.com/downloads/MS5637-02BA03.pdf
>> + *
>> + */
>> +#include <linux/init.h>
>> +#include <linux/device.h>
>> +#include <linux/kernel.h>
>> +#include <linux/stat.h>
>> +#include <linux/module.h>
>> +#include <linux/i2c.h>
>> +#include <linux/iio/iio.h>
>> +#include <linux/iio/sysfs.h>
>> +#include <linux/mutex.h>
>> +
>> +#include "../common/ms_sensors/ms_sensors_i2c.h"
>> +
>> +static const int ms5637_samp_freq[6] = { 960, 480, 240, 120, 60, 30 };
>> +/* String copy of the above const for readability purpose */
>> +static const char ms5637_show_samp_freq[] = "960 480 240 120 60 30";
>> +
>> +static int ms5637_read_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *channel, int *val,
>> + int *val2, long mask)
>> +{
>> + int ret;
>> + int temperature;
>> + unsigned int pressure;
>> + struct ms_tp_dev *dev_data = iio_priv(indio_dev);
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_PROCESSED:
>> + ret = ms_sensors_read_temp_and_pressure(dev_data,
>> + &temperature,
>> + &pressure);
>> + if (ret)
>> + return ret;
>> +
>> + switch (channel->type) {
>> + case IIO_TEMP: /* in °C */
>> + *val = temperature / 1000;
>> + *val2 = (temperature % 1000) * 1000;
>> +
>> + return IIO_VAL_INT_PLUS_MICRO;
>> + case IIO_PRESSURE: /* in kPa */
>> + *val = pressure / 1000;
>> + *val2 = (pressure % 1000) * 1000;
>> +
>> + return IIO_VAL_INT_PLUS_MICRO;
>> + default:
>> + return -EINVAL;
>> + }
>> + case IIO_CHAN_INFO_SAMP_FREQ:
>> + *val = ms5637_samp_freq[dev_data->res_index];
>> +
>> + return IIO_VAL_INT;
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static int ms5637_write_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *chan,
>> + int val, int val2, long mask)
>> +{
>> + struct ms_tp_dev *dev_data = iio_priv(indio_dev);
>> + int i;
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_SAMP_FREQ:
>> + i = ARRAY_SIZE(ms5637_samp_freq);
>> + while (i-- > 0)
>> + if (val == ms5637_samp_freq[i])
>> + break;
>> + if (i < 0)
>> + return -EINVAL;
>> + dev_data->res_index = i;
>> +
>> + return 0;
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static const struct iio_chan_spec ms5637_channels[] = {
>> + {
>> + .type = IIO_TEMP,
>> + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
>> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
>> + },
>> + {
>> + .type = IIO_PRESSURE,
>> + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
>> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
>> + }
>> +};
>> +
>> +static IIO_CONST_ATTR_SAMP_FREQ_AVAIL(ms5637_show_samp_freq);
>> +
>> +static struct attribute *ms5637_attributes[] = {
>> + &iio_const_attr_sampling_frequency_available.dev_attr.attr,
>> + NULL,
>> +};
>> +
>> +static const struct attribute_group ms5637_attribute_group = {
>> + .attrs = ms5637_attributes,
>> +};
>> +
>> +static const struct iio_info ms5637_info = {
>> + .read_raw = ms5637_read_raw,
>> + .write_raw = ms5637_write_raw,
>> + .attrs = &ms5637_attribute_group,
>> + .driver_module = THIS_MODULE,
>> +};
>> +
>> +static int ms5637_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct ms_tp_dev *dev_data;
>> + struct iio_dev *indio_dev;
>> + int ret;
>> +
>> + if (!i2c_check_functionality(client->adapter,
>> + I2C_FUNC_SMBUS_READ_WORD_DATA |
>> + I2C_FUNC_SMBUS_WRITE_BYTE |
>> + I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
>> + dev_err(&client->dev,
>> + "Adapter does not support some transaction\n");
>> + return -ENODEV;
>> + }
>> +
>> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*dev_data));
>> + if (!indio_dev)
>> + return -ENOMEM;
>> +
>> + dev_data = iio_priv(indio_dev);
>> + dev_data->client = client;
>> + dev_data->res_index = 5;
>> + mutex_init(&dev_data->lock);
>> +
>> + indio_dev->info = &ms5637_info;
>> + indio_dev->name = id->name;
>> + indio_dev->dev.parent = &client->dev;
>> + indio_dev->modes = INDIO_DIRECT_MODE;
>> + indio_dev->channels = ms5637_channels;
>> + indio_dev->num_channels = ARRAY_SIZE(ms5637_channels);
>> +
>> + i2c_set_clientdata(client, indio_dev);
>> +
>> + ret = ms_sensors_i2c_reset(client, 0x1E, 3000);
>> + if (ret)
>> + return ret;
>> +
>> + ret = ms_sensors_tp_read_prom(dev_data);
>> + if (ret)
>> + return ret;
>> +
>> + return devm_iio_device_register(&client->dev, indio_dev);
>> +}
>> +
>> +static const struct i2c_device_id ms5637_id[] = {
>> + {"ms5637", 0},
>> + {}
>> +};
>> +
>> +static struct i2c_driver ms5637_driver = {
>> + .probe = ms5637_probe,
>> + .id_table = ms5637_id,
>> + .driver = {
>> + .name = "ms5637",
>> + .owner = THIS_MODULE,
>> + },
>> +};
>> +
>> +module_i2c_driver(ms5637_driver);
>> +
>> +MODULE_DESCRIPTION("Measurement-Specialties ms5637 temperature & pressure driver");
>> +MODULE_AUTHOR("William Markezana <william.markezana@xxxxxxxxxxxxx>");
>> +MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/iio/pressure/ms8607.c b/drivers/iio/pressure/ms8607.c
>> new file mode 100644
>> index 0000000..32de648
>> --- /dev/null
>> +++ b/drivers/iio/pressure/ms8607.c
>> @@ -0,0 +1,330 @@
>> +/*
>> + * ms8607.c - Support for Measurement-Specialties
>> + * ms8607 temperature, pressure and humidity sensor
>> + *
>> + * Copyright (c) 2014 Measurement-Specialties
>> + *
>> + * Licensed under the GPL-2.
>> + *
>> + * (7-bit I2C slave address 0x40 and 0x77)
>> + *
>> + * Datasheet:
>> + * http://www.meas-spec.com/downloads/MS8607-02BA01.pdf
>> + *
>> + */
>> +
>> +#include <linux/init.h>
>> +#include <linux/device.h>
>> +#include <linux/kernel.h>
>> +#include <linux/stat.h>
>> +#include <linux/module.h>
>> +#include <linux/i2c.h>
>> +#include <linux/iio/iio.h>
>> +#include <linux/iio/sysfs.h>
>> +#include <linux/mutex.h>
>> +
>> +#include "../common/ms_sensors/ms_sensors_i2c.h"
>> +
>> +/* MS8607 uses 2 I2C addresses. First one is defined in device tree */
>> +#define MS8607_H_ADDRESS 0x40
>> +
>> +struct ms8607_dev {
>> + struct ms_tp_dev tp;
>> + struct ms_ht_dev ht;
>> +};
>> +
>> +static const int ms8607_samp_freq_tp[6] = { 960, 480, 240, 120, 60, 30 };
>> +/* String copy of the above const for readability purpose */
>> +static const char ms8607_show_samp_freq_tp[] = "960 480 240 120 60 30";
>> +
>> +static const int ms8607_samp_freq_ht[4] = { 20, 40, 70, 120 };
>> +/* String copy of the above const for readability purpose */
>> +static const char ms8607_show_samp_freq_ht[] = "20 40 70 120";
>> +
>> +static int ms8607_read_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *chan, int *val,
>> + int *val2, long mask)
>> +{
>> + int ret;
>> + int temperature;
>> + unsigned int pressure;
>> + unsigned int humidity;
>> + struct ms8607_dev *dev_data = iio_priv(indio_dev);
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_PROCESSED:
>> + switch (chan->type) {
>> + case IIO_TEMP: /* in °C */
>> + ret = ms_sensors_read_temp_and_pressure(&dev_data->tp,
>> + &temperature,
>> + &pressure);
>> + if (ret)
>> + return ret;
>> + *val = temperature / 1000;
>> + *val2 = (temperature % 1000) * 1000;
>> +
>> + return IIO_VAL_INT_PLUS_MICRO;
>> + case IIO_PRESSURE: /* in kPa */
>> + ret = ms_sensors_read_temp_and_pressure(&dev_data->tp,
>> + &temperature,
>> + &pressure);
>> + if (ret)
>> + return ret;
>> + *val = pressure / 1000;
>> + *val2 = (pressure % 1000) * 1000;
>> +
>> + return IIO_VAL_INT_PLUS_MICRO;
>> + case IIO_HUMIDITYRELATIVE: /* in %RH */
>> + ret = ms_sensors_i2c_ht_read_humidity(&dev_data->ht,
>> + &humidity);
>> + if (ret)
>> + return ret;
>> + *val = humidity / 100;
>> + *val2 = (humidity % 100) * 10000;
>> +
>> + return IIO_VAL_INT_PLUS_MICRO;
>> + default:
>> + return -EINVAL;
>> + }
>> + ret = IIO_VAL_INT;
>> + break;
>> + case IIO_CHAN_INFO_SAMP_FREQ:
>> + switch (chan->type) {
>> + case IIO_PRESSURE:
>> + case IIO_TEMP:
>> + *val = ms8607_samp_freq_tp[dev_data->tp.res_index];
>> +
>> + return IIO_VAL_INT;
>> + case IIO_HUMIDITYRELATIVE:
>> + *val = ms8607_samp_freq_ht[dev_data->ht.res_index];
>> +
>> + return IIO_VAL_INT;
>> + default:
>> + return -EINVAL;
>> + }
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static int ms8607_write_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *chan,
>> + int val, int val2, long mask)
>> +{
>> + struct ms8607_dev *dev_data = iio_priv(indio_dev);
>> + int i, ret;
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_SAMP_FREQ:
>> + switch (chan->type) {
>> + case IIO_TEMP:
>> + case IIO_PRESSURE:
>> + i = ARRAY_SIZE(ms8607_samp_freq_tp);
>> + while (i-- > 0)
>> + if (val == ms8607_samp_freq_tp[i])
>> + break;
>> + if (i < 0)
>> + return -EINVAL;
>> + dev_data->tp.res_index = i;
>> +
>> + return 0;
>> + case IIO_HUMIDITYRELATIVE:
>> + i = ARRAY_SIZE(ms8607_samp_freq_ht);
>> + while (i-- > 0)
>> + if (val == ms8607_samp_freq_ht[i])
>> + break;
>> + if (i < 0)
>> + return -EINVAL;
>> + mutex_lock(&dev_data->ht.lock);
>> + dev_data->ht.res_index = i;
>> + ret = ms_sensors_i2c_write_resolution(&dev_data->ht,
>> + i);
>> + mutex_unlock(&dev_data->ht.lock);
>> +
>> + return ret;
>> + default:
>> + return -EINVAL;
>> + }
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static const struct iio_chan_spec ms8607_channels[] = {
>> + {
>> + .type = IIO_TEMP,
>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_PROCESSED) |
>> + BIT(IIO_CHAN_INFO_SAMP_FREQ),
>> + },
>> + {
>> + .type = IIO_PRESSURE,
>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_PROCESSED) |
>> + BIT(IIO_CHAN_INFO_SAMP_FREQ),
>> + },
>> + {
>> + .type = IIO_HUMIDITYRELATIVE,
>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_PROCESSED) |
>> + BIT(IIO_CHAN_INFO_SAMP_FREQ),
>> + }
>> +};
>> +
>> +static ssize_t ms8607_i2c_write_heater(struct device *dev,
>> + struct device_attribute *attr,
>> + const char *buf, size_t len)
>> +{
>> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
>> + struct ms8607_dev *dev_data = iio_priv(indio_dev);
>> +
>> + return ms_sensors_i2c_write_heater(&dev_data->ht, buf, len);
>> +}
>> +
>> +static ssize_t ms8607_attr_read(struct device *dev,
>> + struct device_attribute *attr, char *buf)
>> +{
>> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
>> + struct ms8607_dev *dev_data = iio_priv(indio_dev);
>> + struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
>> +
>> + switch (this_attr->address) {
>> + case MS_SENSORS_ATTR_SERIAL:
>> +
>> + return ms_sensors_i2c_show_serial(&dev_data->ht, buf);
>> + case MS_SENSORS_ATTR_BAT:
>> +
>> + return ms_sensors_i2c_show_battery_low(&dev_data->ht, buf);
>> + case MS_SENSORS_ATTR_HEATER:
>> +
>> + return ms_sensors_i2c_show_heater(&dev_data->ht, buf);
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +IIO_CONST_ATTR(sampling_frequency_available_tp, ms8607_show_samp_freq_tp);
>> +IIO_CONST_ATTR(sampling_frequency_available_h, ms8607_show_samp_freq_ht);
>> +static IIO_DEVICE_ATTR(in_serial, S_IRUGO,
>> + ms8607_attr_read, NULL, MS_SENSORS_ATTR_SERIAL);
>> +static IIO_DEVICE_ATTR(in_battery_low, S_IRUGO,
>> + ms8607_attr_read, NULL, MS_SENSORS_ATTR_BAT);
>> +static IIO_DEVICE_ATTR(heater_enable,
>> + S_IRUGO | S_IWUSR,
>> + ms8607_attr_read,
>> + ms8607_i2c_write_heater, MS_SENSORS_ATTR_HEATER);
>> +
>> +static struct attribute *ms8607_attributes[] = {
>> + &iio_const_attr_sampling_frequency_available_tp.dev_attr.attr,
>> + &iio_const_attr_sampling_frequency_available_h.dev_attr.attr,
>> + &iio_dev_attr_in_serial.dev_attr.attr,
>> + &iio_dev_attr_in_battery_low.dev_attr.attr,
>> + &iio_dev_attr_heater_enable.dev_attr.attr,
>> + NULL,
>> +};
>> +
>> +static const struct attribute_group ms8607_attribute_group = {
>> + .attrs = ms8607_attributes,
>> +};
>> +
>> +static const struct iio_info ms8607_info = {
>> + .read_raw = ms8607_read_raw,
>> + .write_raw = ms8607_write_raw,
>> + .attrs = &ms8607_attribute_group,
>> + .driver_module = THIS_MODULE,
>> +};
>> +
>> +static int ms8607_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct ms8607_dev *dev_data;
>> + struct iio_dev *indio_dev;
>> + int ret;
>> +
>> + if (!i2c_check_functionality(client->adapter,
>> + I2C_FUNC_SMBUS_READ_WORD_DATA |
>> + I2C_FUNC_SMBUS_WRITE_BYTE |
>> + I2C_FUNC_SMBUS_READ_I2C_BLOCK |
>> + I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) {
>> + dev_err(&client->dev,
>> + "Adapter does not support some transaction\n");
>> + return -ENODEV;
>> + }
>> +
>> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*dev_data));
>> + if (!indio_dev)
>> + return -ENOMEM;
>> +
>> + dev_data = iio_priv(indio_dev);
>> + dev_data->tp.client = client;
>> + dev_data->ht.client = i2c_new_dummy(client->adapter, MS8607_H_ADDRESS);
>> + if (!dev_data->ht.client) {
>> + dev_err(&client->dev, "%s: new i2c device failed\n", __func__);
>> + return -ENODEV;
>> + }
>> + dev_data->tp.res_index = 5;
>> + dev_data->ht.res_index = 0;
>> +
>> + mutex_init(&dev_data->tp.lock);
>> + mutex_init(&dev_data->ht.lock);
>> +
>> + indio_dev->info = &ms8607_info;
>> + indio_dev->name = id->name;
>> + indio_dev->dev.parent = &client->dev;
>> + indio_dev->modes = INDIO_DIRECT_MODE;
>> + indio_dev->channels = ms8607_channels;
>> + indio_dev->num_channels = ARRAY_SIZE(ms8607_channels);
>> +
>> + i2c_set_clientdata(client, indio_dev);
>> +
>> + ret = ms_sensors_i2c_reset(client, 0x1E, 3000);
>> + if (ret)
>> + return ret;
>> +
>> + ret = ms_sensors_i2c_reset(dev_data->ht.client, 0xFE, 15000);
>> + if (ret)
>> + return ret;
>> +
>> + ret = ms_sensors_i2c_read_serial(dev_data->ht.client,
>> + &dev_data->ht.serial_number);
>> + if (ret)
>> + return ret;
>> +
>> + ret = ms_sensors_tp_read_prom(&dev_data->tp);
>> + if (ret)
>> + return ret;
>> +
>> + return devm_iio_device_register(&client->dev, indio_dev);
>> +}
>> +
>> +static int ms8607_remove(struct i2c_client *client)
>> +{
>> + struct iio_dev *indio_dev = i2c_get_clientdata(client);
>> + struct ms8607_dev *dev_data = iio_priv(indio_dev);
>> +
>> + i2c_unregister_device(dev_data->ht.client);
>> + devm_iio_device_unregister(&client->dev, indio_dev);
>> +
>> + return 0;
>> +}
>> +
>> +static const struct i2c_device_id ms8607_id[] = {
>> + {"ms8607", 0},
>> + {}
>> +};
>> +
>> +static struct i2c_driver ms8607_driver = {
>> + .probe = ms8607_probe,
>> + .remove = ms8607_remove,
>> + .id_table = ms8607_id,
>> + .driver = {
>> + .name = "ms8607",
>> + .owner = THIS_MODULE,
>> + },
>> +};
>> +
>> +module_i2c_driver(ms8607_driver);
>> +
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_DESCRIPTION("Measurement-Specialties ms8607 temperature, pressure & humidity driver");
>> +MODULE_AUTHOR("William Markezana <william.markezana@xxxxxxxxxxxxx>");
>> +MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>");
>> diff --git a/drivers/iio/temperature/Kconfig b/drivers/iio/temperature/Kconfig
>> index 21feaa4..d9b30de 100644
>> --- a/drivers/iio/temperature/Kconfig
>> +++ b/drivers/iio/temperature/Kconfig
>> @@ -23,4 +23,34 @@ config TMP006
>> This driver can also be built as a module. If so, the module will
>> be called tmp006.
>>
>> +config TSYS01
>> + tristate "Measurement Specialities TSYS01 temperature sensor"
>> + help
>> + If you say yes here you get support for the Measurement Specialties
>> + TSYS01 temperature sensor.
>> +
>> + This driver can also be built as a module. If so, the module will
>> + be called tsys01.
>> +
>> +config TSYS01_I2C
>> + tristate "Measurement Specialities TSYS01 support I2C bus connection"
>> + depends on I2C && TSYS01
>> + select IIO_MS_SENSORS_I2C
>> + help
>> + If you say yes here you build I2C bus for TSYS01.
>> +
>> + This driver can also be built as a module. If so, the module will
>> + be called tsys01_i2c.
>> +
>> +config TSYS02D
>> + tristate "Measurement Specialities TSYS02D temperature sensor"
>> + depends on I2C
>> + select IIO_MS_SENSORS_I2C
>> + help
>> + If you say yes here you get support for the Measurement Specialties
>> + TSYS02D temperature sensor.
>> +
>> + This driver can also be built as a module. If so, the module will
>> + be called tsys02d.
>> +
>> endmenu
>> diff --git a/drivers/iio/temperature/Makefile b/drivers/iio/temperature/Makefile
>> index 40710a8..bcebd17 100644
>> --- a/drivers/iio/temperature/Makefile
>> +++ b/drivers/iio/temperature/Makefile
>> @@ -4,3 +4,6 @@
>>
>> obj-$(CONFIG_MLX90614) += mlx90614.o
>> obj-$(CONFIG_TMP006) += tmp006.o
>> +obj-$(CONFIG_TSYS01) += tsys01.o
>> +obj-$(CONFIG_TSYS01_I2C) += tsys01_i2c.o
>> +obj-$(CONFIG_TSYS02D) += tsys02d.o
>> diff --git a/drivers/iio/temperature/tsys01.c b/drivers/iio/temperature/tsys01.c
>> new file mode 100644
>> index 0000000..6788c23
>> --- /dev/null
>> +++ b/drivers/iio/temperature/tsys01.c
>> @@ -0,0 +1,191 @@
>> +/*
>> + * tsys01.c - Support for Measurement-Specialties tsys01 temperature sensor
>> + *
>> + * Copyright (c) 2015 Measurement-Specialties
>> + *
>> + * Licensed under the GPL-2.
>> + *
>> + * Datasheet:
>> + * http://www.meas-spec.com/downloads/TSYS01_Digital_Temperature_Sensor.pdf
>> + *
>> + */
>> +
>> +#include "tsys01.h"
>> +
>> +#include <linux/init.h>
>> +#include <linux/kernel.h>
>> +#include <linux/stat.h>
>> +#include <linux/iio/sysfs.h>
>> +
>> +/* Multiplication coefficients for temperature computation */
>> +static const int coeff_mul[] = { -1500000, 1000000, -2000000,
>> + 4000000, -2000000 };
>> +
>> +static int tsys01_read_temperature(struct iio_dev *indio_dev,
>> + s32 *temperature)
>> +{
>> + int ret, i;
>> + u32 adc;
>> + s64 temp = 0;
>> + struct tsys01_dev *dev_data = iio_priv(indio_dev);
>> +
>> + mutex_lock(&dev_data->lock);
>> + ret = dev_data->convert_and_read(dev_data->client,
>> + TSYS01_CONVERSION_START,
>> + TSYS01_ADC_READ, 9000, &adc);
>> + mutex_unlock(&dev_data->lock);
>> + if (ret)
>> + return ret;
>> +
>> + adc >>= 8;
>> +
>> + /* Temperature algorithm */
>> + for (i = 4; i > 0; i--) {
>> + temp += coeff_mul[i] *
>> + (s64)dev_data->prom[5 - i];
>> + temp *= (s64)adc;
>> + temp = div64_s64(temp, 100000);
>> + }
>> + temp *= 10;
>> + temp += coeff_mul[0] * (s64)dev_data->prom[5];
>> + temp = div64_s64(temp, 100000);
>> +
>> + *temperature = temp;
>> +
>> + return 0;
>> +}
>> +
>> +static int tsys01_read_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *channel, int *val,
>> + int *val2, long mask)
>> +{
>> + int ret;
>> + s32 temperature;
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_PROCESSED:
>> + switch (channel->type) {
>> + case IIO_TEMP: /* in °C */
>> + ret = tsys01_read_temperature(indio_dev, &temperature);
>> + if (ret)
>> + return ret;
>> + *val = temperature / 1000;
>> + *val2 = (temperature % 1000) * 1000;
>> +
>> + return IIO_VAL_INT_PLUS_MICRO;
>> + default:
>> + return -EINVAL;
>> + }
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static const struct iio_chan_spec tsys01_channels[] = {
>> + {
>> + .type = IIO_TEMP,
>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_PROCESSED),
>> + }
>> +};
>> +
>> +static ssize_t tsys01_show_avail(struct device *dev,
>> + struct device_attribute *attr, char *buf)
>> +{
>> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
>> + struct tsys01_dev *dev_data = iio_priv(indio_dev);
>> + ssize_t len;
>> + int i;
>> + char *ptr = buf;
>> +
>> + for (i = 0 ; i < TSYS01_PROM_WORDS_NB ; i++) {
>> + len = sprintf(ptr, "%x ",
>> + dev_data->prom[i]);
>> + ptr += len;
>> + }
>> + len = ptr - buf;
>> + len += sprintf(ptr, "\n");
>> +
>> + return len;
>> +}
>> +
>> +static IIO_DEVICE_ATTR(in_prom, S_IRUGO,
>> + tsys01_show_avail, NULL, TSYS01_ATTR_PROM);
>> +
>> +static struct attribute *tsys01_attributes[] = {
>> + &iio_dev_attr_in_prom.dev_attr.attr,
>> + NULL,
>> +};
>> +
>> +static const struct attribute_group tsys01_attribute_group = {
>> + .attrs = tsys01_attributes,
>> +};
>> +
>> +static const struct iio_info tsys01_info = {
>> + .read_raw = tsys01_read_raw,
>> + .attrs = &tsys01_attribute_group,
>> + .driver_module = THIS_MODULE,
>> +};
>> +
>> +static bool tsys01_crc_valid(u16 *n_prom)
>> +{
>> + u8 cnt;
>> + u8 sum = 0;
>> +
>> + for (cnt = 0; cnt < TSYS01_PROM_WORDS_NB; cnt++)
>> + sum += ((n_prom[0] >> 8) + (n_prom[0] & 0xFF));
>> +
>> + return (sum == 0);
>> +}
>> +
>> +static int tsys01_read_prom(struct iio_dev *indio_dev)
>> +{
>> + int i, ret;
>> + struct tsys01_dev *dev_data = iio_priv(indio_dev);
>> +
>> + for (i = 0; i < TSYS01_PROM_WORDS_NB; i++) {
>> + ret = dev_data->read_prom_word(dev_data->client,
>> + TSYS01_PROM_READ + (i << 1),
>> + &dev_data->prom[i]);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + if (!tsys01_crc_valid(dev_data->prom)) {
>> + dev_err(&indio_dev->dev,
>> + "prom crc check error\n");
>> + return -ENODEV;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +int tsys01_probe(struct iio_dev *indio_dev, struct device *dev)
>> +{
>> + int ret;
>> + struct tsys01_dev *dev_data = iio_priv(indio_dev);
>> +
>> + mutex_init(&dev_data->lock);
>> +
>> + indio_dev->info = &tsys01_info;
>> + indio_dev->name = dev->driver->name;
>> + indio_dev->dev.parent = dev;
>> + indio_dev->modes = INDIO_DIRECT_MODE;
>> + indio_dev->channels = tsys01_channels;
>> + indio_dev->num_channels = ARRAY_SIZE(tsys01_channels);
>> +
>> + ret = dev_data->reset(dev_data->client, TSYS01_RESET, 3000);
>> + if (ret)
>> + return ret;
>> +
>> + ret = tsys01_read_prom(indio_dev);
>> + if (ret)
>> + return ret;
>> +
>> + return devm_iio_device_register(dev, indio_dev);
>> +}
>> +EXPORT_SYMBOL(tsys01_probe);
>> +
>> +MODULE_DESCRIPTION("Measurement-Specialties tsys01 temperature driver");
>> +MODULE_AUTHOR("William Markezana <william.markezana@xxxxxxxxxxxxx>");
>> +MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/iio/temperature/tsys01.h b/drivers/iio/temperature/tsys01.h
>> new file mode 100644
>> index 0000000..8dc2bcc
>> --- /dev/null
>> +++ b/drivers/iio/temperature/tsys01.h
>> @@ -0,0 +1,43 @@
>> +/*
>> + * TSYS01 temperature sensor driver
>> + *
>> + * Copyright (c) 2015 Measurement-Specialties
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + *
>> + */
>> +
>> +#ifndef _TSYS01_H
>> +#define _TSYS01_H
>> +
>> +#include <linux/device.h>
>> +#include <linux/iio/iio.h>
>> +#include <linux/mutex.h>
>> +#include <linux/module.h>
>> +
>> +/* TSYS01 Commands */
>> +#define TSYS01_RESET 0x1E
>> +#define TSYS01_CONVERSION_START 0x48
>> +#define TSYS01_ADC_READ 0x00
>> +#define TSYS01_PROM_READ 0xA0
>> +
>> +#define TSYS01_PROM_WORDS_NB 8
>> +#define TSYS01_ATTR_PROM 0
>> +
>> +struct tsys01_dev {
>> + void *client;
>> + struct mutex lock; /* lock during conversion */
>> +
>> + int (*reset)(void *cli, u8 cmd, unsigned int delay);
>> + int (*convert_and_read)(void *cli, u8 conv, u8 rd,
>> + unsigned int delay, u32 *adc);
>> + int (*read_prom_word)(void *cli, int cmd, u16 *word);
>> +
>> + u16 prom[TSYS01_PROM_WORDS_NB];
>> +};
>> +
>> +int tsys01_probe(struct iio_dev *indio_dev, struct device *dev);
>> +
>> +#endif /* _TSYS01_H */
>> diff --git a/drivers/iio/temperature/tsys01_i2c.c b/drivers/iio/temperature/tsys01_i2c.c
>> new file mode 100644
>> index 0000000..9bb8b1e
>> --- /dev/null
>> +++ b/drivers/iio/temperature/tsys01_i2c.c
>> @@ -0,0 +1,67 @@
>> +/*
>> + * TSYS01 Measurement-Specialties temperature sensor (i2c bus)
>> + *
>> + * Copyright (c) 2015 Measurement-Specialties
>> + *
>> + * Licensed under the GPL-2.
>> + *
>> + * (7-bit I2C slave address 0x76 or 0x77 depending on CSB bit HW configuration)
>> + *
>> + */
>> +
>> +#include <linux/i2c.h>
>> +
>> +#include "tsys01.h"
>> +#include "../common/ms_sensors/ms_sensors_i2c.h"
>> +
>> +static int tsys01_i2c_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct tsys01_dev *dev_data;
>> + struct iio_dev *indio_dev;
>> +
>> + if (!i2c_check_functionality(client->adapter,
>> + I2C_FUNC_SMBUS_WORD_DATA |
>> + I2C_FUNC_SMBUS_WRITE_BYTE |
>> + I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
>> + dev_err(&client->dev,
>> + "Adapter does not support some transaction\n");
>> + return -ENODEV;
>> + }
>> +
>> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*dev_data));
>> + if (!indio_dev)
>> + return -ENOMEM;
>> +
>> + dev_data = iio_priv(indio_dev);
>> + dev_data->client = client;
>> + dev_data->reset = ms_sensors_i2c_reset;
>> + dev_data->read_prom_word = ms_sensors_i2c_read_prom_word;
>> + dev_data->convert_and_read = ms_sensors_i2c_convert_and_read;
>> +
>> + i2c_set_clientdata(client, indio_dev);
>> +
>> + return tsys01_probe(indio_dev, &client->dev);
>> +}
>> +
>> +static const struct i2c_device_id tsys01_id[] = {
>> + {"tsys01", 0},
>> + {}
>> +};
>> +MODULE_DEVICE_TABLE(i2c, tsys01_id);
>> +
>> +static struct i2c_driver tsys01_driver = {
>> + .probe = tsys01_i2c_probe,
>> + .id_table = tsys01_id,
>> + .driver = {
>> + .name = "tsys01",
>> + .owner = THIS_MODULE,
>> + },
>> +};
>> +
>> +module_i2c_driver(tsys01_driver);
>> +
>> +MODULE_DESCRIPTION("Measurement-Specialties tsys01 temperature driver");
>> +MODULE_AUTHOR("William Markezana <william.markezana@xxxxxxxxxxxxx>");
>> +MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/iio/temperature/tsys02d.c b/drivers/iio/temperature/tsys02d.c
>> new file mode 100644
>> index 0000000..9e2e807
>> --- /dev/null
>> +++ b/drivers/iio/temperature/tsys02d.c
>> @@ -0,0 +1,206 @@
>> +/*
>> + * tsys02d.c - Support for Measurement-Specialties tsys02d temperature sensor
>> + *
>> + * Copyright (c) 2015 Measurement-Specialties
>> + *
>> + * Licensed under the GPL-2.
>> + *
>> + * (7-bit I2C slave address 0x40)
>> + *
>> + * Datasheet:
>> + * http://www.meas-spec.com/downloads/Digital_Sensor_TSYS02D.pdf
>> + *
>> + */
>> +
>> +#include <linux/init.h>
>> +#include <linux/device.h>
>> +#include <linux/kernel.h>
>> +#include <linux/stat.h>
>> +#include <linux/module.h>
>> +#include <linux/iio/iio.h>
>> +#include <linux/iio/sysfs.h>
>> +
>> +#include "../common/ms_sensors/ms_sensors_i2c.h"
>> +
>> +#define TSYS02D_RESET 0xFE
>> +
>> +static const int tsys02d_samp_freq[4] = { 20, 40, 70, 140 };
>> +/* String copy of the above const for readability purpose */
>> +static const char tsys02d_show_samp_freq[] = "20 40 70 140";
>> +
>> +static int tsys02d_read_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *channel, int *val,
>> + int *val2, long mask)
>> +{
>> + int ret;
>> + s32 temperature;
>> + struct ms_ht_dev *dev_data = iio_priv(indio_dev);
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_PROCESSED:
>> + switch (channel->type) {
>> + case IIO_TEMP: /* in °C */
>> + ret = ms_sensors_i2c_ht_read_temperature(dev_data,
>> + &temperature);
>> + if (ret)
>> + return ret;
>> + *val = temperature / 1000;
>> + *val2 = (temperature % 1000) * 1000;
>> +
>> + return IIO_VAL_INT_PLUS_MICRO;
>> + default:
>> + return -EINVAL;
>> + }
>> + case IIO_CHAN_INFO_SAMP_FREQ:
>> + *val = tsys02d_samp_freq[dev_data->res_index];
>> +
>> + return IIO_VAL_INT;
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static int tsys02d_write_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *chan,
>> + int val, int val2, long mask)
>> +{
>> + struct ms_ht_dev *dev_data = iio_priv(indio_dev);
>> + int i, ret;
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_SAMP_FREQ:
>> + i = ARRAY_SIZE(tsys02d_samp_freq);
>> + while (i-- > 0)
>> + if (val == tsys02d_samp_freq[i])
>> + break;
>> + if (i < 0)
>> + return -EINVAL;
>> + mutex_lock(&dev_data->lock);
>> + dev_data->res_index = i;
>> + ret = ms_sensors_i2c_write_resolution(dev_data, i);
>> + mutex_unlock(&dev_data->lock);
>> +
>> + return ret;
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static const struct iio_chan_spec tsys02d_channels[] = {
>> + {
>> + .type = IIO_TEMP,
>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_PROCESSED),
>> + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
>> + }
>> +};
>> +
>> +static ssize_t tsys02_attr_read(struct device *dev,
>> + struct device_attribute *attr, char *buf)
>> +{
>> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
>> + struct ms_ht_dev *dev_data = iio_priv(indio_dev);
>> + struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
>> +
>> + switch (this_attr->address) {
>> + case MS_SENSORS_ATTR_SERIAL:
>> +
>> + return ms_sensors_i2c_show_serial(dev_data, buf);
>> + case MS_SENSORS_ATTR_BAT:
>> +
>> + return ms_sensors_i2c_show_battery_low(dev_data, buf);
>> + default:
>> + return -EINVAL;
>> + }
>> +}
>> +
>> +static IIO_CONST_ATTR_SAMP_FREQ_AVAIL(tsys02d_show_samp_freq);
>> +static IIO_DEVICE_ATTR(in_serial, S_IRUGO,
>> + tsys02_attr_read, NULL,
>> + 0);
>> +static IIO_DEVICE_ATTR(in_battery_low, S_IRUGO,
>> + tsys02_attr_read, NULL,
>> + 0);
>> +
>> +static struct attribute *tsys02d_attributes[] = {
>> + &iio_const_attr_sampling_frequency_available.dev_attr.attr,
>> + &iio_dev_attr_in_serial.dev_attr.attr,
>> + &iio_dev_attr_in_battery_low.dev_attr.attr,
>> + NULL,
>> +};
>> +
>> +static const struct attribute_group tsys02d_attribute_group = {
>> + .attrs = tsys02d_attributes,
>> +};
>> +
>> +static const struct iio_info tsys02d_info = {
>> + .read_raw = tsys02d_read_raw,
>> + .write_raw = tsys02d_write_raw,
>> + .attrs = &tsys02d_attribute_group,
>> + .driver_module = THIS_MODULE,
>> +};
>> +
>> +int tsys02d_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct ms_ht_dev *dev_data;
>> + struct iio_dev *indio_dev;
>> + int ret;
>> +
>> + if (!i2c_check_functionality(client->adapter,
>> + I2C_FUNC_SMBUS_WRITE_BYTE_DATA |
>> + I2C_FUNC_SMBUS_WRITE_BYTE |
>> + I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
>> + dev_err(&client->dev,
>> + "Adapter does not support some transaction\n");
>> + return -ENODEV;
>> + }
>> +
>> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*dev_data));
>> + if (!indio_dev)
>> + return -ENOMEM;
>> +
>> + dev_data = iio_priv(indio_dev);
>> + dev_data->client = client;
>> + dev_data->res_index = 0;
>> + mutex_init(&dev_data->lock);
>> +
>> + indio_dev->info = &tsys02d_info;
>> + indio_dev->name = id->name;
>> + indio_dev->dev.parent = &client->dev;
>> + indio_dev->modes = INDIO_DIRECT_MODE;
>> + indio_dev->channels = tsys02d_channels;
>> + indio_dev->num_channels = ARRAY_SIZE(tsys02d_channels);
>> +
>> + i2c_set_clientdata(client, indio_dev);
>> +
>> + ret = ms_sensors_i2c_reset(client, TSYS02D_RESET, 15000);
>> + if (ret)
>> + return ret;
>> +
>> + ret = ms_sensors_i2c_read_serial(client, &dev_data->serial_number);
>> + if (ret)
>> + return ret;
>> +
>> + return devm_iio_device_register(&client->dev, indio_dev);
>> +}
>> +
>> +static const struct i2c_device_id tsys02d_id[] = {
>> + {"tsys02d", 0},
>> + {}
>> +};
>> +
>> +static struct i2c_driver tsys02d_driver = {
>> + .probe = tsys02d_probe,
>> + .id_table = tsys02d_id,
>> + .driver = {
>> + .name = "tsys02d",
>> + .owner = THIS_MODULE,
>> + },
>> +};
>> +
>> +module_i2c_driver(tsys02d_driver);
>> +
>> +MODULE_DESCRIPTION("Measurement-Specialties tsys02d temperature driver");
>> +MODULE_AUTHOR("William Markezana <william.markezana@xxxxxxxxxxxxx>");
>> +MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>");
>> +MODULE_LICENSE("GPL v2");
>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
