On 06/07/15 13:34, Martin Kepplinger wrote:
> For the devices supported by the mma8452 driver, two interrupt pins are
> available to route the interrupt signals to. By default INT1 is assumed.
>
> This adds a simple boolean DT property, for users to configure it for
> INT2, if that is the wired interrupt pin for them.
>
> This is important for everyone to be able to use this driver, no matter
> how their chip is wired.
>
> Since this doesn't change the default behaviour, it doesn't break anything
> for existing users.
>
> Signed-off-by: Martin Kepplinger <martin.kepplinger@xxxxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Christoph Muellner <christoph.muellner@xxxxxxxxxxxxxxxxxxxxx>
The whole series looks good to me. Just want those acks from Peter and / or
Martin before I apply it.
Thanks,
Jonathan
> ---
> Documentation/devicetree/bindings/iio/accel/mma8452.txt | 2 ++
> drivers/iio/accel/mma8452.c | 14 ++++++++------
> 2 files changed, 10 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
> index 8d98e05..9bad1fc 100644
> --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt
> +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
> @@ -10,6 +10,7 @@ Optional properties:
>
> - interrupt-parent: should be the phandle for the interrupt controller
> - interrupts: interrupt mapping for GPIO IRQ
> + - use_int2: assume interrupt pin wired to INT2 instead of INT1
>
> Example:
>
> @@ -18,4 +19,5 @@ Example:
> reg = <0x1d>;
> interrupt-parent = <&gpio1>;
> interrupts = <5 0>;
> + use_int2;
> };
> diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
> index 2b8ed67..f8ba146 100644
> --- a/drivers/iio/accel/mma8452.c
> +++ b/drivers/iio/accel/mma8452.c
> @@ -1105,12 +1105,14 @@ static int mma8452_probe(struct i2c_client *client,
> int enabled_interrupts = MMA8452_INT_TRANS |
> MMA8452_INT_FF_MT;
>
> - /* Assume wired to INT1 pin */
> - ret = i2c_smbus_write_byte_data(client,
> - MMA8452_CTRL_REG5,
> - supported_interrupts);
> - if (ret < 0)
> - return ret;
> + /* Assume wired to INT1 pin, except "use_int2" is found in DT */
> + if (!of_property_read_bool(client->dev.of_node, "use_int2")) {
> + ret = i2c_smbus_write_byte_data(client,
> + MMA8452_CTRL_REG5,
> + supported_interrupts);
> + if (ret < 0)
> + return ret;
> + }
>
> ret = i2c_smbus_write_byte_data(client,
> MMA8452_CTRL_REG4,
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
