Hello Tomasz, Thank you for notifying me and your feedback, there is a wish from Measurement Specialties to have a separate driver for MS5637 and MS5611. There are a few differences in HW, moreover the driver you pushed does not support resolution change. Note additional drivers from Measurement Specialties will be added soon. I will include your comments in corrections. Thank you, Ludovic Le 16 juin 2015 à 22:42, Tomasz Duszynski <tduszyns@xxxxxxxxx> a écrit : > On Tue, Jun 16, 2015 at 02:33:29PM +0200, Ludovic wrote: >> MS5637 spec : http://www.meas-spec.com/product/pressure/MS5637-02BA03.aspx >> >> This patch has already been submitted some time ago by William Markezana, it was originally developped by me. >> Thank you for all the comments done. Hopefully, everything is ok now. >> >> Thank you in advance for reviewing again. >> > Hi Ludovic, > > Not so long ago I added support for ms5611. Comparing both chips datasheets > didn't reveal much difference, so maybe two patches can somehow be combined to > avoid code duplication. > > A few additional comments below. >> Regards, >> Ludovic >> >> Signed-off-by: Ludovic <ludovic.tancerel@xxxxxxxxxxxxxxxxx> >> --- >> drivers/iio/pressure/Kconfig | 10 + >> drivers/iio/pressure/Makefile | 1 + >> drivers/iio/pressure/ms5637.c | 475 ++++++++++++++++++++++++++++++++++++++++++ >> 3 files changed, 486 insertions(+) >> create mode 100644 drivers/iio/pressure/ms5637.c >> >> diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig >> index a3be537..6c7faa1 100644 >> --- a/drivers/iio/pressure/Kconfig >> +++ b/drivers/iio/pressure/Kconfig >> @@ -52,6 +52,16 @@ config MPL3115 >> To compile this driver as a module, choose M here: the module >> will be called mpl3115. >> >> +config MS5637 >> + tristate "MS5637 pressure & temperature sensor" >> + depends on I2C >> + help >> + If you say yes here you get support for the Measurement Specialties >> + MS5637 pressure and temperature sensor. >> + >> + This driver can also be built as a module. If so, the module will >> + be called ms5637. >> + >> config IIO_ST_PRESS >> tristate "STMicroelectronics pressure sensor Driver" >> depends on (I2C || SPI_MASTER) && SYSFS >> diff --git a/drivers/iio/pressure/Makefile b/drivers/iio/pressure/Makefile >> index 88011f2..2455f8e 100644 >> --- a/drivers/iio/pressure/Makefile >> +++ b/drivers/iio/pressure/Makefile >> @@ -7,6 +7,7 @@ obj-$(CONFIG_BMP280) += bmp280.o >> obj-$(CONFIG_HID_SENSOR_PRESS) += hid-sensor-press.o >> obj-$(CONFIG_MPL115) += mpl115.o >> obj-$(CONFIG_MPL3115) += mpl3115.o >> +obj-$(CONFIG_MS5637) += ms5637.o >> obj-$(CONFIG_IIO_ST_PRESS) += st_pressure.o >> st_pressure-y := st_pressure_core.o >> st_pressure-$(CONFIG_IIO_BUFFER) += st_pressure_buffer.o >> diff --git a/drivers/iio/pressure/ms5637.c b/drivers/iio/pressure/ms5637.c >> new file mode 100644 >> index 0000000..9c647d7 >> --- /dev/null >> +++ b/drivers/iio/pressure/ms5637.c >> @@ -0,0 +1,475 @@ >> +/* >> + * ms5637.c - Support for Measurement-Specialties ms5637 >> + * pressure & temperature sensor >> + * >> + * Copyright (c) 2014 Measurement-Specialties >> + * >> + * Licensed under the GPL-2. >> + * >> + * (7-bit I2C slave address 0x76) >> + * >> + */ >> +#include <linux/init.h> >> +#include <linux/device.h> >> +#include <linux/kernel.h> >> +#include <linux/stat.h> >> +#include <linux/module.h> >> +#include <linux/i2c.h> >> +#include <linux/iio/iio.h> >> +#include <linux/iio/sysfs.h> >> +#include <linux/jiffies.h> >> +#include <linux/delay.h> >> +#include <linux/mutex.h> >> + >> +/* MS5637 Commands */ >> +#define MS5637_RESET 0x1E >> +#define MS5637_TEMPERATURE_CONVERSION_START 0x50 >> +#define MS5637_PRESSURE_CONVERSION_START 0x40 >> +#define MS5637_ADC_READ 0x00 >> +#define MS5637_PROM_READ 0xA0 >> +#define MS5637_PROM_ELEMENTS_NB 7 >> + >> +static const u16 ms5637_conversion_time[] = { 1000, 2000, 3000, >> + 5000, 9000, 17000 }; >> +static const int ms5637_samp_freq[6][2] = { {1800, 0}, {900, 0}, >> + {450, 0}, {225, 0}, >> + {112, 500000}, {56, 250000}, >> + }; >> + >> +struct ms5637_dev { >> + struct i2c_client *client; >> + struct mutex lock; /* mutex protecting this data structure */ >> + u16 calibration_coeffs[MS5637_PROM_ELEMENTS_NB]; >> + bool got_calibration_words; >> + unsigned long last_update; >> + bool valid; >> + int temperature; >> + unsigned int pressure; >> + u8 resolution_index; >> +}; >> + >> +static int ms5637_get_calibration_coeffs(struct ms5637_dev *dev_data, >> + unsigned char index, u16 *word) >> +{ >> + int ret = 0; >> + >> + ret = i2c_smbus_read_word_swapped(dev_data->client, >> + MS5637_PROM_READ + (index << 1)); >> + if (ret < 0) >> + return ret; >> + *word = (u16)ret & 0xFFFF; >> + return 0; >> +} >> + >> +static bool ms5637_crc_check(u16 *n_prom, u8 crc) >> +{ >> + unsigned int cnt, n_bit; >> + u16 n_rem, crc_read; >> + >> + n_rem = 0x0000; >> + crc_read = n_prom[0]; >> + n_prom[MS5637_PROM_ELEMENTS_NB] = 0; >> + n_prom[0] &= 0x0FFF; /* Clear the CRC byte */ >> + >> + for (cnt = 0; cnt < (MS5637_PROM_ELEMENTS_NB + 1) * 2; cnt++) { >> + if (cnt % 2 == 1) >> + n_rem ^= n_prom[cnt >> 1] & 0x00FF; >> + else >> + n_rem ^= n_prom[cnt >> 1] >> 8; >> + >> + for (n_bit = 8; n_bit > 0; n_bit--) { >> + if (n_rem & 0x8000) >> + n_rem = (n_rem << 1) ^ 0x3000; >> + else >> + n_rem <<= 1; >> + } >> + } >> + n_rem >>= 12; >> + n_prom[0] = crc_read; >> + return (n_rem == crc); >> +} >> + >> +static int ms5637_fill_calibration_coeffs(struct ms5637_dev *dev_data) >> +{ >> + int i, ret = 0; >> + >> + for (i = 0; i < MS5637_PROM_ELEMENTS_NB; i++) { >> + ret = ms5637_get_calibration_coeffs( >> + dev_data, i, >> + &dev_data->calibration_coeffs[i]); >> + >> + if (ret < 0) { >> + dev_err(&dev_data->client->dev, >> + "Unable to get calibration coefficients at address %d\n", >> + i + 1); >> + return ret; >> + } >> + >> + dev_dbg(&dev_data->client->dev, "Coeff %d : %d", i, >> + dev_data->calibration_coeffs[i]); >> + } >> + >> + ret = ms5637_crc_check( >> + dev_data->calibration_coeffs, >> + (dev_data->calibration_coeffs[0] & 0xF000) >> 12); >> + if (ret == 0) >> + dev_err(&dev_data->client->dev, >> + "Calibration coefficients crc check error\n"); >> + >> + return 0; >> +} >> + >> +static int ms5637_read_adc_value(struct ms5637_dev *dev_data, u32 *adc_value) >> +{ >> + int ret; >> + u8 buf[3]; >> + >> + ret = >> + i2c_smbus_read_i2c_block_data(dev_data->client, MS5637_ADC_READ, 3, >> + buf); >> + if (ret < 0) >> + return ret; >> + dev_dbg(&dev_data->client->dev, "ADC raw value : %x %x %x\n", buf[0], >> + buf[1], buf[2]); >> + *adc_value = (buf[0] << 16) + (buf[1] << 8) + buf[2]; >> + return 0; >> +} >> + >> +static int ms5637_conversion_and_read_adc(struct ms5637_dev *dev_data, >> + u32 *t_adc, u32 *p_adc) >> +{ >> + int ret; >> + >> + dev_dbg(&dev_data->client->dev, "ms5637_conversion_and_read_adc"); >> + /* Trigger Temperature conversion */ >> + ret = i2c_smbus_write_byte(dev_data->client, >> + MS5637_TEMPERATURE_CONVERSION_START >> + + dev_data->resolution_index * 2); >> + if (ret < 0) >> + return ret; >> + usleep_range(ms5637_conversion_time[dev_data->resolution_index], >> + ms5637_conversion_time[dev_data->resolution_index] + 3000); >> + /* Retrieve ADC value */ >> + ret = ms5637_read_adc_value(dev_data, t_adc); >> + if (ret < 0) >> + return ret; >> + >> + /* Trigger Pressure conversion */ >> + ret = i2c_smbus_write_byte(dev_data->client, >> + MS5637_PRESSURE_CONVERSION_START >> + + dev_data->resolution_index * 2); >> + if (ret < 0) >> + return ret; >> + usleep_range(ms5637_conversion_time[dev_data->resolution_index], >> + ms5637_conversion_time[dev_data->resolution_index] + 3000); >> + /* Retrieve ADC value */ >> + ret = ms5637_read_adc_value(dev_data, p_adc); >> + if (ret < 0) >> + return ret; >> + >> + return 0; >> +} >> + >> +static int ms5637_read_temperature_and_pressure(struct ms5637_dev *dev_data) >> +{ >> + int ret = 0; >> + u32 t_adc, p_adc; >> + s32 dt, temp; >> + s64 off, sens, t2, off2, sens2; >> + >> + mutex_lock(&dev_data->lock); >> + >> + if (time_after(jiffies, dev_data->last_update + HZ / 2) || >> + !dev_data->valid) { >> + if (!dev_data->got_calibration_words) { >> + ret = ms5637_fill_calibration_coeffs(dev_data); >> + if (ret != 0) >> + goto out; >> + >> + dev_data->got_calibration_words = true; >> + } >> + >> + ret = ms5637_conversion_and_read_adc(dev_data, &t_adc, &p_adc); >> + if (ret < 0) { >> + dev_data->got_calibration_words = false; >> + dev_err(&dev_data->client->dev, >> + "Unable to make sensor adc conversion\n"); >> + goto out; >> + } >> + >> + dt = (s32)t_adc - (dev_data->calibration_coeffs[5] << 8); >> + >> + /* Actual temperature = 2000 + dT * TEMPSENS */ >> + temp = >> + 2000 + (((s64)dt * dev_data->calibration_coeffs[6]) >> 23); >> + >> + /* Second order temperature compensation */ >> + if (temp < 2000) { >> + s64 tmp = (s64)temp - 2000; >> + >> + t2 = (3 * ((s64)dt * (s64)dt)) >> 33; >> + off2 = (61 * tmp * tmp) >> 4; >> + sens2 = (29 * tmp * tmp) >> 4; >> + >> + if (temp < -1500) { >> + s64 tmp = (s64)temp + 1500; >> + >> + off2 += 17 * tmp * tmp; >> + sens2 += 9 * tmp * tmp; >> + } >> + } else { >> + t2 = (5 * ((s64)dt * (s64)dt)) >> 38; >> + off2 = 0; >> + sens2 = 0; >> + } >> + >> + /* OFF = OFF_T1 + TCO * dT */ >> + off = (((s64)dev_data->calibration_coeffs[2]) << 17) + >> + ((((s64)dev_data->calibration_coeffs[4]) * (s64)dt) >> 6); >> + off -= off2; >> + >> + /* Sensitivity at actual temperature = SENS_T1 + TCS * dT */ >> + sens = (((s64)dev_data->calibration_coeffs[1]) << 16) >> + + (((s64)dev_data->calibration_coeffs[3] * dt) >> 7); >> + sens -= sens2; >> + >> + /* Temperature compensated pressure = D1 * SENS - OFF */ >> + dev_data->temperature = (temp - t2) * 10; >> + dev_data->pressure = (u32)(((((s64)p_adc * sens) >> 21) >> + - off) >> 15); >> + >> + dev_data->last_update = jiffies; >> + dev_data->valid = true; >> + } >> + out: >> + mutex_unlock(&dev_data->lock); >> + >> + return ret >= 0 ? 0 : ret; >> +} >> + >> +static int ms5637_get_int_plus_micros_index(const int (*vals)[2], int n, >> + int val, int val2) >> +{ >> + while (n-- > 0) >> + if (val == vals[n][0] && val2 == vals[n][1]) >> + return n; >> + return -EINVAL; >> +} >> + >> +static int ms5637_get_samp_freq_index(struct ms5637_dev *dev_data, >> + int val, int val2) >> +{ >> + return ms5637_get_int_plus_micros_index(ms5637_samp_freq, >> + ARRAY_SIZE(ms5637_samp_freq), val, val2); >> +} >> + >> +static ssize_t ms5637_show_int_plus_micros(char *buf, >> + const int (*vals)[2], int n) >> +{ >> + size_t len = 0; >> + >> + while (n-- > 0) >> + len += scnprintf(buf + len, PAGE_SIZE - len, >> + "%d.%06d ", vals[n][0], vals[n][1]); >> + >> + /* replace trailing space by newline */ >> + buf[len - 1] = '\n'; >> + >> + return len; >> +} >> + >> +static ssize_t ms5637_show_samp_freq_avail(struct device *dev, >> + struct device_attribute *attr, >> + char *buf) >> +{ >> + return ms5637_show_int_plus_micros(buf, ms5637_samp_freq, >> + ARRAY_SIZE(ms5637_samp_freq)); >> +} >> + >> +static int ms5637_read_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *channel, int *val, >> + int *val2, long mask) >> +{ >> + int ret; >> + struct ms5637_dev *dev_data = iio_priv(indio_dev); >> + >> + switch (mask) { >> + case IIO_CHAN_INFO_PROCESSED: >> + ret = ms5637_read_temperature_and_pressure(dev_data); >> + if (ret) >> + goto err; >> + switch (channel->type) { >> + case IIO_TEMP: /* in °C */ > probably iio wants milli C >> + *val = dev_data->temperature / 1000; >> + *val2 = (dev_data->temperature - >> + (dev_data->temperature / 1000) * 1000 >> + ) * 1000; > (dev->data->temperature % 1000) * 1000 has same effect but is much shorter >> + break; >> + case IIO_PRESSURE: /* in kPa */ >> + *val = dev_data->pressure / 1000; >> + *val2 = (dev_data->pressure - >> + (dev_data->pressure / 1000) * 1000) * 1000; >> + break; >> + default: >> + return -EINVAL; >> + } >> + break; >> + case IIO_CHAN_INFO_SAMP_FREQ: >> + *val = ms5637_samp_freq[dev_data->resolution_index][0]; >> + *val2 = ms5637_samp_freq[dev_data->resolution_index][1]; >> + break; >> + default: >> + return -EINVAL; >> + } >> + >> + return IIO_VAL_INT_PLUS_MICRO; >> + err: >> + dev_err(&indio_dev->dev, "Device read error\n"); >> + return ret; >> +} >> + >> +static int ms5637_write_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *chan, >> + int val, int val2, long mask) >> +{ >> + struct ms5637_dev *dev_data = iio_priv(indio_dev); >> + int i; >> + >> + switch (mask) { >> + case IIO_CHAN_INFO_SAMP_FREQ: >> + i = ms5637_get_samp_freq_index(dev_data, val, val2); >> + if (i < 0) >> + return -EINVAL; >> + >> + dev_data->resolution_index = i; >> + break; >> + default: >> + return -EINVAL; >> + } >> + return 0; >> +} >> + >> +static const struct iio_chan_spec ms5637_channels[] = { >> + { >> + .type = IIO_TEMP, >> + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ), >> + }, >> + { >> + .type = IIO_PRESSURE, >> + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ), >> + } >> +}; >> + >> +static IIO_DEV_ATTR_SAMP_FREQ_AVAIL(ms5637_show_samp_freq_avail); >> + >> +static struct attribute *ms5637_attributes[] = { >> + &iio_dev_attr_sampling_frequency_available.dev_attr.attr, >> + NULL, >> +}; >> + >> +static const struct attribute_group ms5637_attribute_group = { >> + .attrs = ms5637_attributes, >> +}; >> + >> +static const struct iio_info ms5637_info = { >> + .read_raw = ms5637_read_raw, >> + .write_raw = ms5637_write_raw, >> + .attrs = &ms5637_attribute_group, >> + .driver_module = THIS_MODULE, >> +}; >> + >> +static int ms5637_probe(struct i2c_client *client, >> + const struct i2c_device_id *id) >> +{ >> + struct ms5637_dev *dev_data; >> + struct iio_dev *indio_dev; >> + int ret; >> + >> + if (!i2c_check_functionality(client->adapter, >> + I2C_FUNC_SMBUS_READ_WORD_DATA)) { >> + dev_err(&client->dev, >> + "Adapter does not support SMBus read word transactions\n"); >> + return -ENODEV; >> + } >> + >> + if (!i2c_check_functionality(client->adapter, >> + I2C_FUNC_SMBUS_WRITE_BYTE)) { >> + dev_err(&client->dev, >> + "Adapter does not support SMBus write byte transactions\n"); >> + return -ENODEV; >> + } >> + >> + if (!i2c_check_functionality(client->adapter, >> + I2C_FUNC_SMBUS_READ_I2C_BLOCK)) { >> + dev_err(&client->dev, >> + "Adapter does not support SMBus read block transactions\n"); >> + return -ENODEV; >> + } >> + >> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*dev_data)); >> + if (!indio_dev) >> + return -ENOMEM; >> + >> + dev_data = iio_priv(indio_dev); >> + dev_data->client = client; >> + mutex_init(&dev_data->lock); >> + >> + indio_dev->info = &ms5637_info; >> + indio_dev->name = id->name; >> + indio_dev->dev.parent = &client->dev; >> + indio_dev->modes = INDIO_DIRECT_MODE; >> + indio_dev->channels = ms5637_channels; >> + indio_dev->num_channels = ARRAY_SIZE(ms5637_channels); >> + >> + i2c_set_clientdata(client, indio_dev); >> + ret = i2c_smbus_write_byte(client, MS5637_RESET); >> + if (ret < 0) >> + return ret; >> + usleep_range(3000, 6000); >> + >> + ret = ms5637_fill_calibration_coeffs(dev_data); >> + if (ret == 0) >> + dev_data->got_calibration_words = true; >> + else >> + return ret; >> + >> + ret = iio_device_register(indio_dev); >> + if (ret < 0) >> + return ret; >> + >> + dev_dbg(&client->dev, "Driver initialization done"); >> + return 0; >> +} >> + >> +static int ms5637_remove(struct i2c_client *client) >> +{ >> + struct iio_dev *indio_dev = i2c_get_clientdata(client); >> + >> + devm_iio_device_unregister(&client->dev, indio_dev); >> + >> + return 0; >> +} > seems that nothing special happens on removal, so maybe use > devm_iio_device_register and drop *_remove(). >> + >> +static const struct i2c_device_id ms5637_id[] = { >> + {"ms5637", 0}, >> + {} >> +}; >> + >> +static struct i2c_driver ms5637_driver = { >> + .probe = ms5637_probe, >> + .remove = ms5637_remove, >> + .id_table = ms5637_id, >> + .driver = { >> + .name = "ms5637", >> + .owner = THIS_MODULE, >> + }, >> +}; >> + >> +module_i2c_driver(ms5637_driver); >> + >> +MODULE_LICENSE("GPL"); >> +MODULE_DESCRIPTION("Measurement-Specialties ms5637 temperature driver"); >> +MODULE_AUTHOR("William Markezana <william.markezana@xxxxxxxxxxxxx>"); >> +MODULE_AUTHOR("Ludovic Tancerel <ludovic.tancerel@xxxxxxxxxxxxxxxxx>"); >> -- >> 2.3.7 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-iio" in >> the body of a message to majordomo@xxxxxxxxxxxxxxx >> More majordomo info at http://vger.kernel.org/majordomo-info.html > -- > To unsubscribe from this list: send the line "unsubscribe linux-iio" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
