On 03/12/14 13:31, Daniel Baluta wrote:
> By default both sensors are ACTIVE, in this way the driver
> will work even if CONFIG_PM_RUNTIME is not selected.
>
> Signed-off-by: Daniel Baluta <daniel.baluta@xxxxxxxxx>
Applied to the togreg branch of iio.git
Thanks,
Jonathan
> ---
> drivers/iio/imu/kmx61.c | 114 +++++++++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 112 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/iio/imu/kmx61.c b/drivers/iio/imu/kmx61.c
> index 893f7c8..7536043 100644
> --- a/drivers/iio/imu/kmx61.c
> +++ b/drivers/iio/imu/kmx61.c
> @@ -15,6 +15,8 @@
> #include <linux/i2c.h>
> #include <linux/acpi.h>
> #include <linux/gpio/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/pm_runtime.h>
> #include <linux/iio/iio.h>
> #include <linux/iio/sysfs.h>
>
> @@ -69,6 +71,8 @@
> #define KMX61_ACC_ODR_MASK 0x0F
> #define KMX61_MAG_ODR_MASK 0xF0
>
> +#define KMX61_SLEEP_DELAY_MS 2000
> +
> #define KMX61_CHIP_ID 0x12
>
> /* KMX61 devices */
> @@ -85,6 +89,10 @@ struct kmx61_data {
> bool acc_stby;
> bool mag_stby;
>
> + /* power state */
> + bool acc_ps;
> + bool mag_ps;
> +
> /* config bits */
> u8 range;
> u8 odr_bits;
> @@ -457,6 +465,58 @@ static int kmx61_chip_init(struct kmx61_data *data)
> return 0;
> }
>
> +/**
> + * kmx61_set_power_state() - set power state for kmx61 @device
> + * @data - kmx61 device private pointer
> + * @on - power state to be set for @device
> + * @device - bitmask indicating device for which @on state needs to be set
> + *
> + * Notice that when ACC power state needs to be set to ON and MAG is in
> + * OPERATION then we know that kmx61_runtime_resume was already called
> + * so we must set ACC OPERATION mode here. The same happens when MAG power
> + * state needs to be set to ON and ACC is in OPERATION.
> + */
> +static int kmx61_set_power_state(struct kmx61_data *data, bool on, u8 device)
> +{
> +#ifdef CONFIG_PM_RUNTIME
> + int ret;
> +
> + if (device & KMX61_ACC) {
> + if (on && !data->acc_ps && !data->mag_stby) {
> + ret = kmx61_set_mode(data, 0, KMX61_ACC, true);
> + if (ret < 0)
> + return ret;
> + }
> + data->acc_ps = on;
> + }
> + if (device & KMX61_MAG) {
> + if (on && !data->mag_ps && !data->acc_stby) {
> + ret = kmx61_set_mode(data, 0, KMX61_MAG, true);
> + if (ret < 0)
> + return ret;
> + }
> + data->mag_ps = on;
> + }
> +
> + if (on) {
> + ret = pm_runtime_get_sync(&data->client->dev);
> + } else {
> + pm_runtime_mark_last_busy(&data->client->dev);
> + ret = pm_runtime_put_autosuspend(&data->client->dev);
> + }
> + if (ret < 0) {
> + dev_err(&data->client->dev,
> + "Failed: kmx61_set_power_state for %d, ret %d\n",
> + on, ret);
> + if (on)
> + pm_runtime_put_noidle(&data->client->dev);
> +
> + return ret;
> + }
> +#endif
> + return 0;
> +}
> +
> static int kmx61_read_measurement(struct kmx61_data *data, u8 base, u8 offset)
> {
> int ret;
> @@ -491,13 +551,16 @@ static int kmx61_read_raw(struct iio_dev *indio_dev,
> }
> mutex_lock(&data->lock);
>
> + kmx61_set_power_state(data, true, chan->address);
> ret = kmx61_read_measurement(data, base_reg, chan->scan_index);
> if (ret < 0) {
> + kmx61_set_power_state(data, false, chan->address);
> mutex_unlock(&data->lock);
> return ret;
> }
> *val = sign_extend32(ret >> chan->scan_type.shift,
> chan->scan_type.realbits - 1);
> + kmx61_set_power_state(data, false, chan->address);
>
> mutex_unlock(&data->lock);
> return IIO_VAL_INT;
> @@ -693,12 +756,22 @@ static int kmx61_probe(struct i2c_client *client,
> ret = iio_device_register(data->mag_indio_dev);
> if (ret < 0) {
> dev_err(&client->dev, "Failed to register mag iio device\n");
> - goto err_iio_unregister;
> + goto err_iio_unregister_acc;
> }
>
> + ret = pm_runtime_set_active(&client->dev);
> + if (ret < 0)
> + goto err_iio_unregister_mag;
> +
> + pm_runtime_enable(&client->dev);
> + pm_runtime_set_autosuspend_delay(&client->dev, KMX61_SLEEP_DELAY_MS);
> + pm_runtime_use_autosuspend(&client->dev);
> +
> return 0;
>
> -err_iio_unregister:
> +err_iio_unregister_mag:
> + iio_device_unregister(data->mag_indio_dev);
> +err_iio_unregister_acc:
> iio_device_unregister(data->acc_indio_dev);
> err_chip_uninit:
> kmx61_set_mode(data, KMX61_ALL_STBY, KMX61_ACC | KMX61_MAG, true);
> @@ -709,6 +782,10 @@ static int kmx61_remove(struct i2c_client *client)
> {
> struct kmx61_data *data = i2c_get_clientdata(client);
>
> + pm_runtime_disable(&client->dev);
> + pm_runtime_set_suspended(&client->dev);
> + pm_runtime_put_noidle(&client->dev);
> +
> iio_device_unregister(data->acc_indio_dev);
> iio_device_unregister(data->mag_indio_dev);
>
> @@ -719,6 +796,38 @@ static int kmx61_remove(struct i2c_client *client)
> return 0;
> }
>
> +
> +#ifdef CONFIG_PM_RUNTIME
> +static int kmx61_runtime_suspend(struct device *dev)
> +{
> + struct kmx61_data *data = i2c_get_clientdata(to_i2c_client(dev));
> + int ret;
> +
> + mutex_lock(&data->lock);
> + ret = kmx61_set_mode(data, KMX61_ALL_STBY, KMX61_ACC | KMX61_MAG, true);
> + mutex_unlock(&data->lock);
> +
> + return ret;
> +}
> +
> +static int kmx61_runtime_resume(struct device *dev)
> +{
> + struct kmx61_data *data = i2c_get_clientdata(to_i2c_client(dev));
> + u8 stby = 0;
> +
> + if (!data->acc_ps)
> + stby |= KMX61_ACC_STBY_BIT;
> + if (!data->mag_ps)
> + stby |= KMX61_MAG_STBY_BIT;
> +
> + return kmx61_set_mode(data, stby, KMX61_ACC | KMX61_MAG, true);
> +}
> +#endif
> +
> +static const struct dev_pm_ops kmx61_pm_ops = {
> + SET_RUNTIME_PM_OPS(kmx61_runtime_suspend, kmx61_runtime_resume, NULL)
> +};
> +
> static const struct acpi_device_id kmx61_acpi_match[] = {
> {"KMX61021", 0},
> {}
> @@ -737,6 +846,7 @@ static struct i2c_driver kmx61_driver = {
> .driver = {
> .name = KMX61_DRV_NAME,
> .acpi_match_table = ACPI_PTR(kmx61_acpi_match),
> + .pm = &kmx61_pm_ops,
> },
> .probe = kmx61_probe,
> .remove = kmx61_remove,
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
