Add support for Freescale MMA9551L Intelligent Motion-Sensing Platform. The driver supports raw reads for acceleration and inclination, as well as configuring an inclination rate-of-change events. The events can be used similarly to an Android sensor Tilt event. The specifications can be downloaded from: http://www.freescale.com/files/sensors/doc/ref_manual/MMA955xLSWRM.pdf Signed-off-by: Irina Tirdea <irina.tirdea@xxxxxxxxx> Signed-off-by: Vlad Dogaru <vlad.dogaru@xxxxxxxxx> --- Changes since v2: - all three events can be enabled at the same time, each using a separate GPIO line. - simplify GPIO config code. - style fixes as suggested by Jonathan. Changes since v1: - invert logic in mma9551_set_device_state(). Setting the sleep bit to 1 puts the device into sleep. - do not use scan_index for channels, since we don't support buffering. - style fixes as suggested by Peter. drivers/iio/accel/Kconfig | 10 + drivers/iio/accel/Makefile | 1 + drivers/iio/accel/mma9551.c | 960 ++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 971 insertions(+) create mode 100644 drivers/iio/accel/mma9551.c diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig index 9b9be87..d80616d 100644 --- a/drivers/iio/accel/Kconfig +++ b/drivers/iio/accel/Kconfig @@ -105,4 +105,14 @@ config KXCJK1013 To compile this driver as a module, choose M here: the module will be called kxcjk-1013. +config MMA9551 + tristate "Freescale MMA9551L Intelligent Motion-Sensing Platform Driver" + depends on I2C + help + Say yes here to build support for the Freescale MMA9551L + Intelligent Motion-Sensing Platform Driver. + + To compile this driver as a module, choose M here: the module + will be called mma9551. + endmenu diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile index a593996..de5b9cb 100644 --- a/drivers/iio/accel/Makefile +++ b/drivers/iio/accel/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o obj-$(CONFIG_KXCJK1013) += kxcjk-1013.o obj-$(CONFIG_KXSD9) += kxsd9.o obj-$(CONFIG_MMA8452) += mma8452.o +obj-$(CONFIG_MMA9551) += mma9551.o obj-$(CONFIG_IIO_ST_ACCEL_3AXIS) += st_accel.o st_accel-y := st_accel_core.o diff --git a/drivers/iio/accel/mma9551.c b/drivers/iio/accel/mma9551.c new file mode 100644 index 0000000..d677042 --- /dev/null +++ b/drivers/iio/accel/mma9551.c @@ -0,0 +1,960 @@ +/* + * Freescale MMA9551L Intelligent Motion-Sensing Platform driver + * Copyright (c) 2014, Intel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ + +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/slab.h> +#include <linux/acpi.h> +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> +#include <linux/iio/events.h> + +#define MMA9551_DRV_NAME "mma9551" +#define MMA9551_IRQ_NAME "mma9551_event" +#define MMA9551_GPIO_NAME "mma9551_int" +#define MMA9551_GPIO_COUNT 4 + +/* Applications IDs */ +#define MMA9551_APPID_VERSION 0x00 +#define MMA9551_APPID_GPIO 0x03 +#define MMA9551_APPID_AFE 0x06 +#define MMA9551_APPID_TILT 0x0B +#define MMA9551_APPID_SLEEP_WAKE 0x12 +#define MMA9551_APPID_RESET 0x17 +#define MMA9551_APPID_NONE 0xff + +/* Command masks for mailbox write command */ +#define MMA9551_CMD_READ_VERSION_INFO 0x00 +#define MMA9551_CMD_READ_CONFIG 0x10 +#define MMA9551_CMD_WRITE_CONFIG 0x20 +#define MMA9551_CMD_READ_STATUS 0x30 + +enum mma9551_gpio_pin { + mma9551_gpio6 = 0, + mma9551_gpio7, + mma9551_gpio8, + mma9551_gpio9, + mma9551_gpio_max = mma9551_gpio9, +}; + +/* Mailbox read command */ +#define MMA9551_RESPONSE_COCO BIT(7) + +/* Error-Status codes returned in mailbox read command */ +#define MMA9551_MCI_ERROR_NONE 0x00 +#define MMA9551_MCI_ERROR_PARAM 0x04 +#define MMA9551_MCI_INVALID_COUNT 0x19 +#define MMA9551_MCI_ERROR_COMMAND 0x1C +#define MMA9551_MCI_ERROR_INVALID_LENGTH 0x21 +#define MMA9551_MCI_ERROR_FIFO_BUSY 0x22 +#define MMA9551_MCI_ERROR_FIFO_ALLOCATED 0x23 +#define MMA9551_MCI_ERROR_FIFO_OVERSIZE 0x24 + +/* GPIO Application */ +#define MMA9551_GPIO_POL_MSB 0x08 +#define MMA9551_GPIO_POL_LSB 0x09 + +/* Sleep/Wake application */ +#define MMA9551_SLEEP_CFG 0x06 +#define MMA9551_SLEEP_CFG_SNCEN BIT(0) +#define MMA9551_SLEEP_CFG_SCHEN BIT(2) + +/* AFE application */ +#define MMA9551_AFE_X_ACCEL_REG 0x00 +#define MMA9551_AFE_Y_ACCEL_REG 0x02 +#define MMA9551_AFE_Z_ACCEL_REG 0x04 + +/* Tilt application (inclination in IIO terms). */ +#define MMA9551_TILT_XZ_ANG_REG 0x00 +#define MMA9551_TILT_YZ_ANG_REG 0x01 +#define MMA9551_TILT_XY_ANG_REG 0x02 +#define MMA9551_TILT_XY_QUAD_SHIFT 0 +#define MMA9551_TILT_YZ_QUAD_SHIFT 2 +#define MMA9551_TILT_XZ_QUAD_SHIFT 4 +#define MMA9551_TILT_ANGFLG BIT(7) +#define MMA9551_TILT_QUAD_REG 0x03 +#define MMA9551_TILT_CFG_REG 0x01 +#define MMA9551_TILT_ANG_THRESH_MASK 0x0f + +/* Tilt events are mapped to the first three GPIO pins. */ +enum mma9551_tilt_axis { + mma9551_x = 0, + mma9551_y, + mma9551_z, +}; + +/* + * A response is composed of: + * - control registers: MB0-3 + * - data registers: MB4-31 + * + * A request is composed of: + * - mbox to write to (always 0) + * - control registers: MB1-4 + * - data registers: MB5-31 + */ +#define MMA9551_MAILBOX_CTRL_REGS 4 +#define MMA9551_MAX_MAILBOX_DATA_REGS 28 +#define MMA9551_MAILBOX_REGS 32 + +#define MMA9551_I2C_READ_RETRIES 5 +#define MMA9551_I2C_READ_DELAY 50 /* us */ + +struct mma9551_mbox_request { + u8 start_mbox; /* Always 0. */ + u8 app_id; + /* + * See Section 5.3.1 of the MMA955xL Software Reference Manual. + * + * Bit 7: reserved, always 0 + * Bits 6-4: command + * Bits 3-0: upper bits of register offset + */ + u8 cmd_off; + u8 lower_off; + u8 nbytes; + u8 buf[MMA9551_MAX_MAILBOX_DATA_REGS - 1]; +} __packed; + +struct mma9551_mbox_response { + u8 app_id; + /* + * See Section 5.3.3 of the MMA955xL Software Reference Manual. + * + * Bit 7: COCO + * Bits 6-0: Error code. + */ + u8 coco_err; + u8 nbytes; + u8 req_bytes; + u8 buf[MMA9551_MAX_MAILBOX_DATA_REGS]; +} __packed; + +struct mma9551_version_info { + __be32 device_id; + u8 rom_version[2]; + u8 fw_version[2]; + u8 hw_version[2]; + u8 fw_build[2]; +}; + +struct mma9551_data { + struct i2c_client *client; + struct mutex mutex; + int event_enabled[3]; + int irqs[MMA9551_GPIO_COUNT]; +}; + +static int mma9551_transfer(struct i2c_client *client, + u8 app_id, u8 command, u16 offset, + u8 *inbytes, int num_inbytes, + u8 *outbytes, int num_outbytes) +{ + struct mma9551_mbox_request req; + struct mma9551_mbox_response rsp; + struct i2c_msg in, out; + u8 req_len, err_code; + int ret; + int retries; + + if (offset >= 1 << 12) { + dev_err(&client->dev, "register offset too large\n"); + return -EINVAL; + } + + req_len = 1 + MMA9551_MAILBOX_CTRL_REGS + num_inbytes; + req.start_mbox = 0; + req.app_id = app_id; + req.cmd_off = command | (offset >> 8); + req.lower_off = offset; + + if (command == MMA9551_CMD_WRITE_CONFIG) + req.nbytes = num_inbytes; + else + req.nbytes = num_outbytes; + if (num_inbytes) + memcpy(req.buf, inbytes, num_inbytes); + + out.addr = client->addr; + out.flags = 0; + out.len = req_len; + out.buf = (u8 *)&req; + + ret = i2c_transfer(client->adapter, &out, 1); + if (ret < 0) { + dev_err(&client->dev, "i2c write failed\n"); + return ret; + } + + retries = MMA9551_I2C_READ_RETRIES; + do { + udelay(MMA9551_I2C_READ_DELAY); + + in.addr = client->addr; + in.flags = I2C_M_RD; + in.len = sizeof(rsp); + in.buf = (u8 *)&rsp; + + ret = i2c_transfer(client->adapter, &in, 1); + if (ret < 0) { + dev_err(&client->dev, "i2c read failed\n"); + return ret; + } + + if (rsp.coco_err & MMA9551_RESPONSE_COCO) + break; + } while (--retries > 0); + + if (retries == 0) { + dev_err(&client->dev, + "timed out while waiting for command response\n"); + return -ETIMEDOUT; + } + + if (rsp.app_id != app_id) { + dev_err(&client->dev, + "app_id mismatch in response got %02x expected %02x\n", + rsp.app_id, app_id); + return -EINVAL; + } + + err_code = rsp.coco_err & ~MMA9551_RESPONSE_COCO; + if (err_code != MMA9551_MCI_ERROR_NONE) { + dev_err(&client->dev, "read returned error %x\n", err_code); + return -EINVAL; + } + + if (rsp.nbytes != rsp.req_bytes) { + dev_err(&client->dev, + "output length mismatch got %d expected %d\n", + rsp.nbytes, num_outbytes); + return -EINVAL; + } + + if (num_outbytes) + memcpy(outbytes, rsp.buf, num_outbytes); + + return 0; +} + +static int mma9551_read_config_byte(struct i2c_client *client, u8 app_id, + u16 reg, u8 *val) +{ + return mma9551_transfer(client, app_id, MMA9551_CMD_READ_CONFIG, + reg, NULL, 0, val, 1); +} + +static int mma9551_write_config_byte(struct i2c_client *client, u8 app_id, + u16 reg, u8 val) +{ + return mma9551_transfer(client, app_id, MMA9551_CMD_WRITE_CONFIG, reg, + &val, 1, NULL, 0); +} + +static int mma9551_read_status_byte(struct i2c_client *client, u8 app_id, + u16 reg, u8 *val) +{ + return mma9551_transfer(client, app_id, MMA9551_CMD_READ_STATUS, + reg, NULL, 0, val, 1); +} + +static int mma9551_read_status_word(struct i2c_client *client, u8 app_id, + u16 reg, u16 *val) +{ + int ret; + __be16 v; + + ret = mma9551_transfer(client, app_id, MMA9551_CMD_READ_STATUS, + reg, NULL, 0, (u8 *)&v, 2); + *val = be16_to_cpu(v); + + return ret; +} + +static int mma9551_update_config_bits(struct i2c_client *client, u8 app_id, + u8 reg, u8 mask, u8 val) +{ + int ret; + u8 tmp, orig; + + ret = mma9551_read_config_byte(client, app_id, reg, &orig); + if (ret < 0) + return ret; + + tmp = orig & ~mask; + tmp |= val & mask; + + if (tmp == orig) + return 0; + + return mma9551_write_config_byte(client, app_id, reg, tmp); +} + +/* + * The polarity parameter is described in section 6.2.2, page 66, of the + * Software Reference Manual. Basically, polarity=0 means the interrupt + * line has the same value as the selected bit, while polarity=1 means + * the line is inverted. + */ +static int mma9551_gpio_config(struct i2c_client *client, + enum mma9551_gpio_pin pin, + u8 app_id, u8 bitnum, int polarity) +{ + u8 reg, pol_mask, pol_val; + int ret; + + if (pin > mma9551_gpio_max) { + dev_err(&client->dev, "bad GPIO pin\n"); + return -EINVAL; + } + + /* + * Pin 6 is configured by regs 0x00 and 0x01, pin 7 by 0x02 and + * 0x03, and so on. + */ + reg = pin * 2; + + ret = mma9551_write_config_byte(client, MMA9551_APPID_GPIO, + reg, app_id); + if (ret < 0) { + dev_err(&client->dev, "error setting GPIO app_id\n"); + return ret; + } + + ret = mma9551_write_config_byte(client, MMA9551_APPID_GPIO, + reg + 1, bitnum); + if (ret < 0) { + dev_err(&client->dev, "error setting GPIO bit number\n"); + return ret; + } + + switch (pin) { + case mma9551_gpio6: + reg = MMA9551_GPIO_POL_LSB; + pol_mask = 1 << 6; + break; + case mma9551_gpio7: + reg = MMA9551_GPIO_POL_LSB; + pol_mask = 1 << 7; + break; + case mma9551_gpio8: + reg = MMA9551_GPIO_POL_MSB; + pol_mask = 1 << 0; + break; + case mma9551_gpio9: + reg = MMA9551_GPIO_POL_MSB; + pol_mask = 1 << 1; + break; + } + pol_val = polarity ? pol_mask : 0; + + ret = mma9551_update_config_bits(client, MMA9551_APPID_GPIO, reg, + pol_mask, pol_val); + if (ret < 0) + dev_err(&client->dev, "error setting GPIO polarity\n"); + + return ret; +} + +static int mma9551_read_version(struct i2c_client *client) +{ + struct mma9551_version_info info; + int ret; + + ret = mma9551_transfer(client, MMA9551_APPID_VERSION, 0x00, 0x00, + NULL, 0, (u8 *)&info, sizeof(info)); + if (ret < 0) + return ret; + + dev_info(&client->dev, "Device ID 0x%x, firmware version %02x.%02x\n", + be32_to_cpu(info.device_id), info.fw_version[0], + info.fw_version[1]); + + return 0; +} + +/* + * Use 'false' as the second parameter to cause the device to enter + * sleep. + */ +static int mma9551_set_device_state(struct i2c_client *client, + bool enable) +{ + return mma9551_update_config_bits(client, MMA9551_APPID_SLEEP_WAKE, + MMA9551_SLEEP_CFG, + MMA9551_SLEEP_CFG_SNCEN, + enable ? 0 : MMA9551_SLEEP_CFG_SNCEN); +} + +static int mma9551_read_incli_chan(struct i2c_client *client, + const struct iio_chan_spec *chan, + int *val) +{ + u8 quad_shift, quad_mask, angle, quadrant; + u16 reg_addr; + int ret; + + switch (chan->channel2) { + case IIO_MOD_X: + reg_addr = MMA9551_TILT_YZ_ANG_REG; + quad_shift = MMA9551_TILT_YZ_QUAD_SHIFT; + break; + case IIO_MOD_Y: + reg_addr = MMA9551_TILT_XZ_ANG_REG; + quad_shift = MMA9551_TILT_XZ_QUAD_SHIFT; + break; + case IIO_MOD_Z: + reg_addr = MMA9551_TILT_XY_ANG_REG; + quad_shift = MMA9551_TILT_XY_QUAD_SHIFT; + break; + default: + return -EINVAL; + } + + ret = mma9551_read_status_byte(client, MMA9551_APPID_TILT, + reg_addr, &angle); + if (ret < 0) + return ret; + + ret = mma9551_read_status_byte(client, MMA9551_APPID_TILT, + MMA9551_TILT_QUAD_REG, &quadrant); + if (ret < 0) + return ret; + + angle &= ~MMA9551_TILT_ANGFLG; + quad_mask = 0x03 << quad_shift; + quadrant = (quadrant & quad_mask) >> quad_shift; + + if (quadrant == 1 || quadrant == 3) + *val = 90 * (quadrant + 1) - angle; + else + *val = angle + 90 * quadrant; + + return IIO_VAL_INT; +} + +static int mma9551_read_accel_chan(struct i2c_client *client, + const struct iio_chan_spec *chan, + int *val, int *val2) +{ + u16 reg_addr; + s16 raw_accel; + int ret; + + switch (chan->channel2) { + case IIO_MOD_X: + reg_addr = MMA9551_AFE_X_ACCEL_REG; + break; + case IIO_MOD_Y: + reg_addr = MMA9551_AFE_Y_ACCEL_REG; + break; + case IIO_MOD_Z: + reg_addr = MMA9551_AFE_Z_ACCEL_REG; + break; + default: + return -EINVAL; + } + + ret = mma9551_read_status_word(client, MMA9551_APPID_AFE, + reg_addr, &raw_accel); + if (ret < 0) + return ret; + + *val = raw_accel; + + return IIO_VAL_INT; +} + +static int mma9551_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct mma9551_data *data = iio_priv(indio_dev); + int ret; + + switch (mask) { + case IIO_CHAN_INFO_PROCESSED: + switch (chan->type) { + case IIO_INCLI: + mutex_lock(&data->mutex); + ret = mma9551_read_incli_chan(data->client, + chan, val); + mutex_unlock(&data->mutex); + return ret; + default: + return -EINVAL; + } + case IIO_CHAN_INFO_RAW: + switch (chan->type) { + case IIO_ACCEL: + mutex_lock(&data->mutex); + ret = mma9551_read_accel_chan(data->client, + chan, val, val2); + mutex_unlock(&data->mutex); + return ret; + default: + return -EINVAL; + } + case IIO_CHAN_INFO_SCALE: + switch (chan->type) { + case IIO_ACCEL: + *val = 0; + *val2 = 2440; + return IIO_VAL_INT_PLUS_MICRO; + default: + return -EINVAL; + } + default: + return -EINVAL; + } +} + +static int mma9551_read_event_config(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir) +{ + struct mma9551_data *data = iio_priv(indio_dev); + + switch (chan->type) { + case IIO_INCLI: + /* IIO counts axes from 1, because IIO_NO_MOD is 0. */ + return data->event_enabled[chan->channel2 - 1]; + default: + return -EINVAL; + } +} + +static int mma9551_config_incli_event(struct iio_dev *indio_dev, + enum iio_modifier axis, + int state) +{ + struct mma9551_data *data = iio_priv(indio_dev); + enum mma9551_tilt_axis mma_axis; + int ret; + + /* IIO counts axes from 1, because IIO_NO_MOD is 0. */ + mma_axis = axis - 1; + + if (data->event_enabled[mma_axis] == state) + return 0; + + if (state == 0) { + ret = mma9551_gpio_config(data->client, mma_axis, + MMA9551_APPID_NONE, 0, 0); + if (ret < 0) + return ret; + } else { + int bitnum; + + /* Bit 7 of each angle register holds the angle flag. */ + switch (axis) { + case IIO_MOD_X: + bitnum = 7 + 8 * MMA9551_TILT_YZ_ANG_REG; + break; + case IIO_MOD_Y: + bitnum = 7 + 8 * MMA9551_TILT_XZ_ANG_REG; + break; + case IIO_MOD_Z: + bitnum = 7 + 8 * MMA9551_TILT_XY_ANG_REG; + break; + default: + return -EINVAL; + } + + ret = mma9551_gpio_config(data->client, mma_axis, + MMA9551_APPID_TILT, bitnum, 0); + if (ret < 0) + return ret; + } + + data->event_enabled[mma_axis] = state; + + return ret; +} + +static int mma9551_write_event_config(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + int state) +{ + struct mma9551_data *data = iio_priv(indio_dev); + int ret; + + switch (chan->type) { + case IIO_INCLI: + mutex_lock(&data->mutex); + ret = mma9551_config_incli_event(indio_dev, + chan->channel2, state); + mutex_unlock(&data->mutex); + return ret; + default: + return -EINVAL; + } +} + +static int mma9551_write_event_value(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + enum iio_event_info info, + int val, int val2) +{ + struct mma9551_data *data = iio_priv(indio_dev); + int ret; + + switch (chan->type) { + case IIO_INCLI: + if (val2 != 0 || val < 1 || val > 10) + return -EINVAL; + mutex_lock(&data->mutex); + ret = mma9551_update_config_bits(data->client, + MMA9551_APPID_TILT, + MMA9551_TILT_CFG_REG, + MMA9551_TILT_ANG_THRESH_MASK, + val); + mutex_unlock(&data->mutex); + return ret; + default: + return -EINVAL; + } +} + +static int mma9551_read_event_value(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + enum iio_event_info info, + int *val, int *val2) +{ + struct mma9551_data *data = iio_priv(indio_dev); + int ret; + u8 tmp; + + switch (chan->type) { + case IIO_INCLI: + mutex_lock(&data->mutex); + ret = mma9551_read_config_byte(data->client, + MMA9551_APPID_TILT, + MMA9551_TILT_CFG_REG, &tmp); + mutex_unlock(&data->mutex); + if (ret < 0) + return ret; + *val = tmp & MMA9551_TILT_ANG_THRESH_MASK; + *val2 = 0; + return IIO_VAL_INT; + default: + return -EINVAL; + } +} + +static const struct iio_event_spec mma9551_incli_event = { + .type = IIO_EV_TYPE_ROC, + .dir = IIO_EV_DIR_RISING, + .mask_separate = BIT(IIO_EV_INFO_ENABLE), + .mask_shared_by_type = BIT(IIO_EV_INFO_VALUE), +}; + +#define MMA9551_ACCEL_CHANNEL(axis) { \ + .type = IIO_ACCEL, \ + .modified = 1, \ + .channel2 = axis, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ +} + +#define MMA9551_INCLI_CHANNEL(axis) { \ + .type = IIO_INCLI, \ + .modified = 1, \ + .channel2 = axis, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), \ + .event_spec = &mma9551_incli_event, \ + .num_event_specs = 1, \ +} + +static const struct iio_chan_spec mma9551_channels[] = { + MMA9551_ACCEL_CHANNEL(IIO_MOD_X), + MMA9551_ACCEL_CHANNEL(IIO_MOD_Y), + MMA9551_ACCEL_CHANNEL(IIO_MOD_Z), + + MMA9551_INCLI_CHANNEL(IIO_MOD_X), + MMA9551_INCLI_CHANNEL(IIO_MOD_Y), + MMA9551_INCLI_CHANNEL(IIO_MOD_Z), +}; + +static const struct iio_info mma9551_info = { + .driver_module = THIS_MODULE, + .read_raw = mma9551_read_raw, + .read_event_config = mma9551_read_event_config, + .write_event_config = mma9551_write_event_config, + .read_event_value = mma9551_read_event_value, + .write_event_value = mma9551_write_event_value, +}; + +static irqreturn_t mma9551_event_handler(int irq, void *private) +{ + struct iio_dev *indio_dev = private; + struct mma9551_data *data = iio_priv(indio_dev); + int mma_axis, ret, i; + u16 reg; + u8 val; + + mutex_lock(&data->mutex); + + mma_axis = -1; + for (i = 0; i < 3; i++) + if (irq == data->irqs[i]) { + mma_axis = i; + break; + } + + if (mma_axis == -1) { + /* IRQ was triggered on 4th line, which we don't use. */ + dev_warn(&data->client->dev, + "irq triggered on unused line %d\n", data->irqs[3]); + goto out; + } + + switch (mma_axis) { + case mma9551_x: + reg = MMA9551_TILT_YZ_ANG_REG; + break; + case mma9551_y: + reg = MMA9551_TILT_XZ_ANG_REG; + break; + case mma9551_z: + reg = MMA9551_TILT_XY_ANG_REG; + break; + } + + /* + * Read the angle even though we don't use it, otherwise we + * won't get any further interrupts. + */ + ret = mma9551_read_status_byte(data->client, MMA9551_APPID_TILT, + reg, &val); + if (ret < 0) { + dev_err(&data->client->dev, + "error %d reading tilt register in IRQ\n", ret); + goto out; + } + + iio_push_event(indio_dev, + IIO_MOD_EVENT_CODE(IIO_INCLI, 0, + (mma_axis + 1), + IIO_EV_TYPE_ROC, + IIO_EV_DIR_RISING), + iio_get_time_ns()); + +out: + mutex_unlock(&data->mutex); + + return IRQ_HANDLED; +} + +static int mma9551_init(struct mma9551_data *data) +{ + int ret; + + ret = mma9551_read_version(data->client); + if (ret) + return ret; + + /* Power on chip and enable doze mode. */ + ret = mma9551_update_config_bits(data->client, + MMA9551_APPID_SLEEP_WAKE, + MMA9551_SLEEP_CFG, + MMA9551_SLEEP_CFG_SCHEN | MMA9551_SLEEP_CFG_SNCEN, + MMA9551_SLEEP_CFG_SCHEN); + if (ret < 0) + return ret; + + return 0; +} + +static int mma9551_gpio_probe(struct iio_dev *indio_dev) +{ + struct gpio_desc *gpio; + int i, ret; + struct mma9551_data *data = iio_priv(indio_dev); + struct device *dev = &data->client->dev; + + for (i = 0; i < MMA9551_GPIO_COUNT; i++) { + gpio = devm_gpiod_get_index(dev, MMA9551_GPIO_NAME, i); + if (IS_ERR(gpio)) { + dev_err(dev, "acpi gpio get index failed\n"); + return PTR_ERR(gpio); + } + + ret = gpiod_direction_input(gpio); + if (ret) + return ret; + + data->irqs[i] = gpiod_to_irq(gpio); + ret = devm_request_threaded_irq(dev, data->irqs[i], + NULL, mma9551_event_handler, + IRQF_TRIGGER_RISING | IRQF_ONESHOT, + MMA9551_IRQ_NAME, indio_dev); + if (ret < 0) { + dev_err(dev, "request irq %d failed\n", data->irqs[i]); + return ret; + } + + dev_dbg(dev, "gpio resource, no:%d irq:%d\n", + desc_to_gpio(gpio), data->irqs[i]); + } + + return 0; +} + +static const char *mma9551_match_acpi_device(struct device *dev) +{ + const struct acpi_device_id *id; + + id = acpi_match_device(dev->driver->acpi_match_table, dev); + if (!id) + return NULL; + + return dev_name(dev); +} + +static int mma9551_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct mma9551_data *data; + struct iio_dev *indio_dev; + const char *name = NULL; + int ret; + + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); + if (!indio_dev) + return -ENOMEM; + + data = iio_priv(indio_dev); + i2c_set_clientdata(client, indio_dev); + data->client = client; + + if (id) + name = id->name; + else if (ACPI_HANDLE(&client->dev)) + name = mma9551_match_acpi_device(&client->dev); + + ret = mma9551_init(data); + if (ret < 0) + return ret; + + mutex_init(&data->mutex); + memset(data->event_enabled, 0, sizeof(data->event_enabled)); + + indio_dev->dev.parent = &client->dev; + indio_dev->channels = mma9551_channels; + indio_dev->num_channels = ARRAY_SIZE(mma9551_channels); + indio_dev->name = name; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->info = &mma9551_info; + + ret = mma9551_gpio_probe(indio_dev); + if (ret < 0) + return ret; + + ret = iio_device_register(indio_dev); + if (ret < 0) { + dev_err(&client->dev, "unable to register iio device\n"); + return ret; + } + + return 0; +} + +static int mma9551_remove(struct i2c_client *client) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(client); + struct mma9551_data *data = iio_priv(indio_dev); + + iio_device_unregister(indio_dev); + mutex_lock(&data->mutex); + mma9551_set_device_state(data->client, false); + mutex_unlock(&data->mutex); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int mma9551_suspend(struct device *dev) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); + struct mma9551_data *data = iio_priv(indio_dev); + + mutex_lock(&data->mutex); + mma9551_set_device_state(data->client, false); + mutex_unlock(&data->mutex); + + return 0; +} + +static int mma9551_resume(struct device *dev) +{ + struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev)); + struct mma9551_data *data = iio_priv(indio_dev); + + mutex_lock(&data->mutex); + mma9551_set_device_state(data->client, true); + mutex_unlock(&data->mutex); + + return 0; +} +#else +#define mma9551_suspend NULL +#define mma9551_resume NULL +#endif + +static const struct dev_pm_ops mma9551_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(mma9551_suspend, mma9551_resume) +}; + +static const struct acpi_device_id mma9551_acpi_match[] = { + {"MMA9551", 0}, + {}, +}; + +MODULE_DEVICE_TABLE(acpi, mma9551_acpi_match); + +static const struct i2c_device_id mma9551_id[] = { + {"mma9551", 0}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, mma9551_id); + +static struct i2c_driver mma9551_driver = { + .driver = { + .name = MMA9551_DRV_NAME, + .acpi_match_table = ACPI_PTR(mma9551_acpi_match), + .pm = &mma9551_pm_ops, + }, + .probe = mma9551_probe, + .remove = mma9551_remove, + .id_table = mma9551_id, +}; + +module_i2c_driver(mma9551_driver); + +MODULE_AUTHOR("Irina Tirdea <irina.tirdea@xxxxxxxxx>"); +MODULE_AUTHOR("Vlad Dogaru <vlad.dogaru@xxxxxxxxx>"); +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("MMA9551L motion-sensing platform driver"); -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html