Hello, Mr. Meerwald
Thank you for your advice.
2013년 09월 09일 16:57, Peter Meerwald 쓴 글:
>
>> This patch add a new driver for Capella CM36651 proximity and RGB light
>> sensor.
>> The driver exposes two channels: light and proximity. It also support
>> detection proximity event.
>
> comments inline;
> I do not have the chip, but I don't think that the code will work and
> intended
>
After I have made this driver, I have checked device working on test board.
>> This driver supports:
>> - events - rising and falling proximity events.
>> - reading channels through read_raw callback.
>>
>> Signed-off-by: Beomho Seo <beomho.seo@xxxxxxxxxxx>
>> ---
>> drivers/iio/light/Kconfig | 11 +
>> drivers/iio/light/cm36651.c | 607
>> +++++++++++++++++++++++++++++++++++++++++++
>> 2 files changed, 618 insertions(+)
>> create mode 100644 drivers/iio/light/cm36651.c
>>
>> diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig
>> index bf9fa0d..66fb76f 100644
>> --- a/drivers/iio/light/Kconfig
>> +++ b/drivers/iio/light/Kconfig
>> @@ -75,4 +75,15 @@ config VCNL4000
>> To compile this driver as a module, choose M here: the
>> module will be called vcnl4000.
>>
>> +config CM36651
>
> sensors to be listed in alphabetical order
>
I have fixed it.
>> + depends on I2C
>> + tristate "CM36651 driver"
>> + help
>> + Say Y here if you use cm36651.
>> + This option enables proximity & RGB sensor using
>> + Capella cm36651 device driver.
>> +
>> + To compile this driver as a module, choose M here:
>> + the module will be called cm36651.
>> +
>> endmenu
>> diff --git a/drivers/iio/light/cm36651.c b/drivers/iio/light/cm36651.c
>> new file mode 100644
>> index 0000000..b3e1f0d
>> --- /dev/null
>> +++ b/drivers/iio/light/cm36651.c
>> @@ -0,0 +1,607 @@
>> +/*
>> + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
>> + * Author: Beomho Seo <beomho.seo@xxxxxxxxxxx>
>> + *
>> + * This program is free software; you can redistribute it and/or modify it
>> + * under the terms of the GNU General Public License version 2, as
>> published
>> + * by the Free Software Foundation.
>> + */
>> +
>> +#include <linux/delay.h>
>> +#include <linux/i2c.h>
>> +#include <linux/mutex.h>
>> +#include <linux/module.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/regulator/consumer.h>
>> +#include <linux/iio/iio.h>
>> +#include <linux/iio/sysfs.h>
>> +#include <linux/iio/events.h>
>> +
>> +/* slave address 0x19 for PS of 7 bit addressing protocol for I2C */
> consistently start comments with uppercase letter
>
I use uppercase letter starting comments.
>> +#define CM36651_I2C_ADDR_PS 0x19
>
> interesting, the chip seems to have two i2c addresses, the other one is
> 0x18
>
> is this really one chip? an option would be to do two drivers: one for
> ALS, one for proximity
>
CM36651 is one chip. I have checked it. CM36651 apply slave address 0x18 for CS and 0x19 for PS of 7 bit addressing protocol for I2C. CM36651 contains are 8-bit command register following each of slave address. All operations can ve contrroled by the command register.
>> +
>> +/* Ambient light sensor */
>> +#define CS_CONF1 0x00
>> +#define CS_CONF2 0x01
>> +#define CS_CONF3 0x06
>> +
>> +#define RED 0x00
>> +#define GREEN 0x01
>> +#define BLUE 0x02
>> +#define WHITE 0x03
>> +
>> +/* Proximity sensor */
>> +#define PS_CONF1 0x00
>> +#define PS_THD 0x01
>> +#define PS_CANC 0x02
>> +#define PS_CONF2 0x03
>> +
>> +#define ALS_REG_NUM 3
>> +#define PS_REG_NUM 4
>> +#define ALS_CHANNEL_NUM 4
>> +#define INITIAL_THD 0x09
>> +#define SCAN_MODE_LIGHT 0
>> +#define SCAN_MODE_PROX 1
>> +
>> +enum {
>> + CM36651_LIGHT_EN,
>> + CM36651_PROXIMITY_EN,
>> + CM36651_PROXIMITY_EV_EN,
>> +};
>> +
>> +enum cm36651_cmd {
>> + CM36651_CMD_READ_RAW_LIGHT,
>> + CM36651_CMD_READ_RAW_PROXIMITY,
>> + CM36651_CMD_PROX_EV_EN,
>> + CM36651_CMD_PROX_EV_DIS,
>> +};
>> +
>> +enum {
>> + CM36651_CLOSE_PROXIMITY,
>> + CM36651_FAR_PROXIMITY,
>> +};
>> +
>> +/* register settings */
>> +static const u8 als_reg_setting[ALS_REG_NUM][2] = {
>> + { 0x00, 0x04 }, /* CS_CONF1 */
>
> use your #defines instead of a comment, e.g. { CS_CONF1, 0x04 }
>
> what are the magic constants 0x04, 0x08?
>
I'll use #defines instedad of a comment next version.
And magic constants(e.g. 0x04, 0x08) will be made to #defines also.
>> + { 0x01, 0x08 }, /* CS_CONF2 */
>> + { 0x06, 0x00 } /* CS_CONF3 */
>> +};
>> +
>> +static const u8 ps_reg_setting[PS_REG_NUM][2] = {
>> + { 0x00, 0x3C }, /* PS_CONF1 */
>> + { 0x01, 0x09 }, /* PS_THD */
>> + { 0x02, 0x00 }, /* PS_CANC */
>> + { 0x03, 0x13 }, /* PS_CONF2 */
>> +};
>> +
>> +struct cm36651_data {
>> + const struct cm36651_platform_data *pdata;
>> + struct i2c_client *client;
>> + struct i2c_client *ps_client;
>> + struct mutex lock;
>> + struct regulator *vled_reg;
>> + unsigned long flags;
>> + u8 thres;
>> + u16 color[4];
>> +};
>> +
>> +int cm36651_i2c_read_byte(struct i2c_client *client, u8 *val)
>> +{
>> + int ret = 0;
>> + struct i2c_msg msg[1];
>> +
>> + if (!client->adapter)
>> + return -ENODEV;
>> +
>> + /* send slave address & command */
>> + msg->addr = client->addr;
>> + msg->flags = I2C_M_RD;
>> + msg->len = 1;
>> + msg->buf = val;
>> +
>> + ret = i2c_transfer(client->adapter, msg, 1);
>> + if (ret != 1) {
>> + dev_err(&client->dev, "i2c transfer error ret: %d\n", ret);
>> + ret = -EIO;
>> + }
>> +
>> + return ret;
>> +}
>
> use i2c_smbus_read_byte_data() instead?
>
I'll try use i2c_smbus_* API at next patch.
>> +
>> +int cm36651_i2c_read_word(struct i2c_client *client, u8 command, u16 *val)
>> +{
>> + int ret = 0;
>> + struct i2c_msg msg[2];
>> + unsigned char data[2] = { 0, };
>> +
>> + if (!client->adapter)
>> + return -ENODEV;
>> +
>> + /* send slave address & command */
>> + msg[0].addr = client->addr;
>> + msg[0].flags = 0;
>> + msg[0].len = 1;
>> + msg[0].buf = &command;
>> +
>> + /* read word data */
>> + msg[1].addr = client->addr;
>> + msg[1].flags = I2C_M_RD;
>> + msg[1].len = 2;
>> + msg[1].buf = data;
>> +
>> + ret = i2c_transfer(client->adapter, msg, 2);
>> + if (ret != 2) {
>> + dev_err(&client->dev, "i2c transfer error ret: %d\n", ret);
>> + ret = -EIO;
>> + }
>> + *val = le16_to_cpup((__le16 *)data);
>> +
>> + return ret;
>> +}
>
> use i2c_smbus_read_word_data() instead?
>
>> +
>> +int cm36651_i2c_write_byte(struct i2c_client *client, u8 command, u8 val)
>> +{
>> + int ret;
>> + struct i2c_msg msg[1];
>> + unsigned char data[2] = { command, val };
>> +
>> + if (!client->adapter)
>> + return -ENODEV;
>> +
>> + /* send slave address & command */
>> + msg->addr = client->addr;
>> + msg->flags = 0;
>> + msg->len = 2;
>> + msg->buf = data;
>> +
>> + ret = i2c_transfer(client->adapter, msg, 1);
>> + if (ret != 1) {
>> + dev_err(&client->dev, "i2c transfer error ret: %d\n", ret);
>> + ret = -EIO;
>> + }
>> +
>> + return ret;
>> +}
>
> use i2c_smbus_write_byte_data() instead?
>
>> +
>> +static int cm36651_setup_reg(struct cm36651_data *cm36651)
>> +{
>> + struct i2c_client *client = cm36651->client;
>> + int ret = 0, i = 0;
>
> no need to initialize ret, tmp and i
>
I'll fix on your comment.
>> + u8 tmp = 0;
>> +
>> + /* ALS initialization */
>> + for (i = 0; i < ALS_REG_NUM; i++) {
>> + ret = cm36651_i2c_write_byte(client,
>> + als_reg_setting[i][0], als_reg_setting[i][1]);
>> + if (ret < 0)
>> + goto err_setup_reg;
>> + }
>> +
>> + /* PS initialization */
>> + for (i = 0; i < PS_REG_NUM; i++) {
>> + ret = cm36651_i2c_write_byte(cm36651->ps_client,
>> + ps_reg_setting[i][0], ps_reg_setting[i][1]);
>> + if (ret < 0)
>> + goto err_setup_reg;
>> + }
>> +
>> + ret = cm36651_i2c_read_byte(cm36651->ps_client, &tmp);
>> + if (ret < 0)
>> + goto err_setup_reg;
>> +
>> + /* printing the initial proximity value with no contact */
>> + dev_dbg(&client->dev, "initial proximity value: %d\n", tmp);
>> +
>> + /* device turn off */
>> + ret = cm36651_i2c_write_byte(client, CS_CONF1, 0x01);
>
> use a #define for 0x01 to describe function
>
OK. I'll use a #define for 0x01 to describe function.
>> + if (ret < 0)
>> + goto err_setup_reg;
>> +
>> + ret = cm36651_i2c_write_byte(cm36651->ps_client, PS_CONF1, 0x01);
>> + if (ret < 0)
>> + goto err_setup_reg;
>> +
>> + return 0;
>> +
>> +err_setup_reg:
>> + dev_err(&client->dev, "cm36651_setup_reg() failed: %d\n", ret);
>> + return ret;
>> +}
>> +
>> +static int cm36651_read_output(struct cm36651_data *cm36651,
>> + int scan_index, int *val)
>> +{
>
> val is not used?
>
I'll check it, and then fix.
>> + struct i2c_client *client = cm36651->client;
>> + int i;
>> + int ret = -EINVAL;
>> + u8 prox_val;
>> +
>> + switch (scan_index) {
>> + case SCAN_MODE_LIGHT:
>> + for (i = 0; i < ALS_CHANNEL_NUM; i++) {
>> + ret = cm36651_i2c_read_word(client, i,
>> + &cm36651->color[i]);
>
> I think this is wrong: i is 0,1,2,3,4 but CS_CONF1, CS_CONF2 is 0, 1 as
> well -- so the config registers are read here?
>
> the channel data (red,green,blue,clear) is at addresses 0x02 .. 0x05
> (according to
> https://github.com/mozilla-b2g/kernel-android-galaxy-s2-ics/blob/master/drivers/sensor/cm36651.c)
>
i is 0, 1, 2, 3. Also in above link, you can refer to loghtsensor_lux_show and cm36641_work_func_light function, cm36651_i2c_read_word function need to cm36651_data struct,
address, command, and val data. Where, color Macros(RED, GREEN, BLUE, WHITE) are command data. Not address. Address is fixed on CM36651_ALS Macro.
And then, ALS_WH_M, ... ALS_WL_L(0x02...0x05) registers like below:
ALS_WH_M 0x02 ALS High Threshold Window setting [15:8]
ALS_WH_L 0x03 ALS High Threshold Whndow setting [7:0]
...
ALS_WL_M 0x05 ALS Low Threshold Window setting [7:0]
>> + if (ret < 0)
>> + goto read_err;
>> + }
>> +
>> + dev_dbg(&client->dev, "red: %d, green: %d, blue: %d, white: %d\n",
>> + cm36651->color[0] + 1, cm36651->color[1] + 1,
>> + cm36651->color[2] + 1, cm36651->color[3] + 1);
>> +
>> + ret = cm36651_i2c_write_byte(client, CS_CONF1, 0x01);
>
> what does this do?
>
Above code is light sensor disable setting.
>> + if (ret < 0)
>> + goto write_err;
>> +
>> + break;
>> + case SCAN_MODE_PROX:
>> + ret = cm36651_i2c_read_byte(cm36651->ps_client, &prox_val);
>> + if (ret < 0)
>> + goto read_err;
>> +
>> + dev_dbg(&client->dev, "proximity value: %d\n", prox_val);
>
> prox_val is not returned?
>
I'll check and fix at next version patch.
>> +
>> + ret = cm36651_i2c_write_byte(cm36651->ps_client,
>> + PS_CONF1, 0x01);
>> + if (ret < 0)
>> + goto write_err;
>> +
>> + break;
>> + }
>> +
>> + return ret;
>> +
>> +read_err:
>> + dev_err(&client->dev, "register read failed\n");
>> + return ret;
>> +
>> +write_err:
>> + dev_err(&client->dev, "register write failed\n");
>> + return ret;
>> +}
>> +
>> +static irqreturn_t cm36651_irq_handler(int irq, void *data)
>> +{
>> + struct iio_dev *indio_dev = data;
>> + struct cm36651_data *cm36651 = iio_priv(indio_dev);
>> + struct i2c_client *client = cm36651->client;
>> + int ev_dir, val, ret;
>> + u64 ev_code;
>> + u8 tmp;
>> +
>
> tmp must be initialized with the command?
>
I'll fix it on your advice.
>> + ret = cm36651_i2c_read_byte(cm36651->ps_client, &tmp);
>> + if (ret < 0) {
>> + dev_err(&client->dev,
>> + "%s: data read failed: %d\n", __func__, ret);
>> + return IRQ_NONE;
>
> should always return IRQ_HANDLED
>
I'll fix it on your advice.
>> + }
>> +
>> + if (tmp < ps_reg_setting[1][1]) {
>> + ev_dir = IIO_EV_DIR_RISING;
>> + val = CM36651_FAR_PROXIMITY;
>> + } else {
>> + ev_dir = IIO_EV_DIR_FALLING;
>> + val = CM36651_CLOSE_PROXIMITY;
>> + }
>> +
>> + ev_code = IIO_UNMOD_EVENT_CODE(IIO_PROXIMITY,
>> + CM36651_CMD_READ_RAW_PROXIMITY,
>> + IIO_EV_TYPE_THRESH, ev_dir);
>> +
>> + iio_push_event(indio_dev, ev_code, iio_get_time_ns());
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static int cm36651_set_operation_mode(struct cm36651_data *cm36651,
>> + enum cm36651_cmd cmd)
>> +{
>> + struct i2c_client *client = cm36651->client;
>> + int ret = 0;
>> + int i;
>> +
>> + switch (cmd) {
>> + case CM36651_CMD_READ_RAW_LIGHT:
>> + ret = cm36651_i2c_write_byte(client, CS_CONF1, 0x04);
>> + break;
>> + case CM36651_CMD_READ_RAW_PROXIMITY:
>> + ret = cm36651_i2c_write_byte(cm36651->ps_client,
>> + PS_CONF1, 0x3C);
>> + break;
>> + case CM36651_CMD_PROX_EV_EN:
>> + if (test_bit(CM36651_PROXIMITY_EV_EN, &cm36651->flags)) {
>> + dev_err(&client->dev,
>> + "Already proximity event enable state\n");
>> + return ret;
>> + }
>> + set_bit(CM36651_PROXIMITY_EV_EN, &cm36651->flags);
>> + for (i = 0; i < 4; i++) {
>> + ret = cm36651_i2c_write_byte(cm36651->ps_client,
>> + ps_reg_setting[i][0], ps_reg_setting[i][1]);
>> + if (ret < 0)
>> + goto write_err;
>> + }
>> + enable_irq(client->irq);
>> + break;
>> + case CM36651_CMD_PROX_EV_DIS:
>> + if (!test_bit(CM36651_PROXIMITY_EV_EN, &cm36651->flags)) {
>> + dev_err(&client->dev,
>> + "Already proximity event disable state\n");
>> + return ret;
>> + }
>> + clear_bit(CM36651_PROXIMITY_EV_EN, &cm36651->flags);
>> + disable_irq(client->irq);
>> + ret = cm36651_i2c_write_byte(cm36651->ps_client,
>> + PS_CONF1, 0x01);
>> + break;
>> + }
>> +
>> + if (ret < 0)
>> + dev_err(&client->dev, "write register failed\n");
>> +
>> + return ret;
>> +
>> +write_err:
>> + dev_err(&client->dev, "proximity event toe enable is failed\n");
>
> typo: toe; rephase
>
I have fixed on correct typo.
>> + return ret;
>> +}
>> +
>> +static int cm36651_read_channel(struct cm36651_data *cm36651,
>> + struct iio_chan_spec const *chan, int *val)
>> +{
>> + struct i2c_client *client = cm36651->client;
>> + enum cm36651_cmd cmd = 0;
>> + int ret;
>> +
>> + if (chan->scan_index == SCAN_MODE_LIGHT)
>> + cmd = CM36651_CMD_READ_RAW_LIGHT;
>> + else /* SCAN_MODE_PROX */
>> + cmd = CM36651_CMD_READ_RAW_PROXIMITY;
>> +
>> + ret = cm36651_set_operation_mode(cm36651, cmd);
>> + if (ret < 0) {
>> + dev_err(&client->dev, "cm36651 set operation mode failed\n");
>> + return ret;
>> + }
>> + /* raw data integration time */
>> + msleep(50);
>> + ret = cm36651_read_output(cm36651, chan->scan_index, val);
>
> _read_output() does not return data in val!
>
OK. I'll fix it.
>> + if (ret < 0) {
>> + dev_err(&client->dev, "cm36651 read output failed\n");
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cm36651_read_raw(struct iio_dev *indio_dev,
>> + struct iio_chan_spec const *chan,
>> + int *val, int *val2, long mask)
>> +{
>> + struct cm36651_data *cm36651 = iio_priv(indio_dev);
>> + int ret = -EINVAL;
>> +
>> + mutex_lock(&cm36651->lock);
>> +
>> + switch (mask) {
>> + case IIO_CHAN_INFO_RAW:
>> + ret = cm36651_read_channel(cm36651, chan, val);
>> + break;
>> + }
>> + mutex_unlock(&cm36651->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static int cm36651_read_thresh(struct iio_dev *indio_dev,
>> + u64 event_code, int *val)
>> +{
>> + struct cm36651_data *cm36651 = iio_priv(indio_dev);
>> + int chan_type = IIO_EVENT_CODE_EXTRACT_CHAN_TYPE(event_code);
>> + int event_type = IIO_EVENT_CODE_EXTRACT_TYPE(event_code);
>> +
>> + if (event_type != IIO_EV_TYPE_THRESH || chan_type != IIO_PROXIMITY)
>> + return -EINVAL;
>> +
>> + if (!cm36651->thres)
>> + *val = ps_reg_setting[1][1]; /* initial threshold value */
>> + else
>> + *val = cm36651->thres;
>> +
>> + return 0;
>> +}
>> +
>> +static int cm36651_write_thresh(struct iio_dev *indio_dev,
>> + u64 event_code, int val)
>> +{
>> + struct cm36651_data *cm36651 = iio_priv(indio_dev);
>> + struct i2c_client *client = cm36651->client;
>> + int ret;
>> +
>> + cm36651->thres = val;
>> + ret = cm36651_i2c_write_byte(cm36651->ps_client,
>> + PS_THD, cm36651->thres);
>> +
>> + if (ret < 0) {
>> + dev_err(&client->dev, "PS register read faied: %d\n", ret);
>> + return ret;
>> + }
>> + dev_dbg(&client->dev, "new threshold is 0x%x\n", cm36651->thres);
>> +
>> + return 0;
>> +}
>> +
>> +static int cm36651_write_event_config(struct iio_dev *indio_dev,
>> + u64 event_code, int state)
>> +{
>> + struct cm36651_data *cm36651 = iio_priv(indio_dev);
>> + enum cm36651_cmd cmd;
>> + int chan_type = IIO_EVENT_CODE_EXTRACT_CHAN_TYPE(event_code);
>> + int ret = -EINVAL;
>> +
>> + mutex_lock(&cm36651->lock);
>> +
>> + if (chan_type == IIO_PROXIMITY) {
>> + cmd = state ? CM36651_CMD_PROX_EV_EN : CM36651_CMD_PROX_EV_DIS;
>> + ret = cm36651_set_operation_mode(cm36651, cmd);
>> + }
>> +
>> + mutex_unlock(&cm36651->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static int cm36651_read_event_config(struct iio_dev *indio_dev, u64
>> event_code)
>> +{
>> + struct cm36651_data *cm36651 = iio_priv(indio_dev);
>> + int chan_type = IIO_EVENT_CODE_EXTRACT_CHAN_TYPE(event_code);
>> + int event_en = -EINVAL;
>> +
>> + mutex_lock(&cm36651->lock);
>> +
>> + if (chan_type == IIO_PROXIMITY)
>> + event_en = test_bit(CM36651_PROXIMITY_EV_EN, &cm36651->flags);
>> +
>> + mutex_unlock(&cm36651->lock);
>> +
>> + return event_en;
>> +}
>> +
>> +static const struct iio_chan_spec cm36651_channels[] = {
>> + {
>> + .type = IIO_LIGHT,
>> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
>> + .scan_type = {
>> + .sign = 'u',
>> + .realbits = 16,
>> + .shift = 0,
>> + .storagebits = 16,
>> + },
>> + .scan_index = SCAN_MODE_LIGHT
>> + },
>> + {
>> + .type = IIO_PROXIMITY,
>> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
>> + .scan_type = {
>> + .sign = 'u',
>> + .realbits = 8,
>> + .shift = 0,
>> + .storagebits = 8,
>> + },
>> + .scan_index = SCAN_MODE_PROX,
>> + .event_mask = IIO_EV_BIT(IIO_EV_TYPE_THRESH, IIO_EV_DIR_EITHER)
>> + },
>> +};
>> +
>> +static const struct iio_info cm36651_info = {
>> + .driver_module = THIS_MODULE,
>> + .read_raw = &cm36651_read_raw,
>> + .read_event_value = &cm36651_read_thresh,
>> + .write_event_value = &cm36651_write_thresh,
>> + .read_event_config = &cm36651_read_event_config,
>> + .write_event_config = &cm36651_write_event_config,
>> +};
>> +
>> +static int cm36651_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct cm36651_data *cm36651;
>> + struct iio_dev *indio_dev;
>> + unsigned long irqflag;
>> + int ret;
>> +
>> + dev_dbg(&client->dev, "cm36651 light/proxymity sensor probe\n");
>> +
>> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*cm36651));
>> + if (!indio_dev)
>> + return -ENOMEM;
>> +
>> + cm36651 = iio_priv(indio_dev);
>> +
>> + cm36651->vled_reg = devm_regulator_get(&client->dev, "vled");
>> + if (IS_ERR(cm36651->vled_reg)) {
>> + dev_err(&client->dev, "get regulator vled failed\n");
>> + return PTR_ERR(cm36651->vled_reg);
>> + }
>> +
>> + ret = regulator_enable(cm36651->vled_reg);
>> + if (ret) {
>> + dev_err(&client->dev, "enable regulator failed\n");
>> + return ret;
>> + }
>> +
>> + i2c_set_clientdata(client, indio_dev);
>> +
>> + cm36651->client = client;
>> + cm36651->ps_client = i2c_new_dummy(client->adapter,
>> + CM36651_I2C_ADDR_PS);
>> + mutex_init(&cm36651->lock);
>> + indio_dev->dev.parent = &client->dev;
>> + indio_dev->channels = cm36651_channels;
>> + indio_dev->num_channels = ARRAY_SIZE(cm36651_channels);
>> + indio_dev->info = &cm36651_info;
>> + indio_dev->name = id->name;
>> + indio_dev->modes = INDIO_DIRECT_MODE;
>> +
>> + ret = cm36651_setup_reg(cm36651);
>> +
>> + irqflag = IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | IRQF_ONESHOT;
>
> rising and falling?
>
There are distance from sensor device. Rising is far from device. on the contrary to this Falling is close from device.
>> + ret = request_threaded_irq(client->irq, NULL, cm36651_irq_handler,
>> + irqflag, "cm36651_proximity", indio_dev);
>> + if (ret) {
>> + dev_err(&client->dev, "%s: request irq failed\n", __func__);
>> + return ret;
>> + }
>> + disable_irq(client->irq);
>> +
>> + ret = iio_device_register(indio_dev);
>> + if (ret) {
>> + regulator_disable(cm36651->vled_reg);
>
> irq not freed
>
It will be fixed.
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int cm36651_remove(struct i2c_client *client)
>> +{
>> + struct iio_dev *indio_dev = i2c_get_clientdata(client);
>> + struct cm36651_data *cm36651 = iio_priv(indio_dev);
>> +
>> + iio_device_unregister(indio_dev);
>> + regulator_disable(cm36651->vled_reg);
>> + free_irq(client->irq, indio_dev);
>> + iio_device_free(indio_dev);
>
> iio_device_free() not needed since using devm_iio_device_alloc()
>
It will be fixed.
>> +
>> + return 0;
>> +}
>> +
>> +static const struct i2c_device_id cm36651_id[] = {
>> + { "cm36651", 0 },
>> + { }
>> +};
>> +
>> +MODULE_DEVICE_TABLE(i2c, cm36651_id);
>> +
>> +static const struct of_device_id cm36651_of_match[] = {
>> + { .compatible = "capella,cm36651" },
>> + { }
>> +};
>> +
>> +static struct i2c_driver cm36651_driver = {
>> + .driver = {
>> + .name = "cm36651",
>> + .of_match_table = of_match_ptr(cm36651_of_match),
>> + .owner = THIS_MODULE,
>> + },
>> + .probe = cm36651_probe,
>> + .remove = cm36651_remove,
>> + .id_table = cm36651_id,
>> +};
>> +
>> +module_i2c_driver(cm36651_driver);
>> +
>> +MODULE_AUTHOR("Beomho Seo <beomho.seo@xxxxxxxxxxx>");
>> +MODULE_DESCRIPTION("CM36651 proximity/ambient light sensor driver");
>> +MODULE_LICENSE("GPL v2");
>>
>
I will fix and send v2 patch soon.
Best regards,
Beomho Seo
--
Beomho Seo, Assistant Engineer
System S/W Lab., S/W Platform Team, Software Center
Samsung Electronics
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
