On 08/16/2013 08:47 AM, Jacek Anaszewski wrote:
> Hi all,
>
> I'd like to consult the implementation of DT binding for the I2C device
> that exposes two interrupt pins (INT1 and INT2). Both pins can be
> configured to generate either data ready interrupts or event interrupts.
> I want to implement DT binding that will handle also the situation
> when only one of the interrupt sources is routed from the device
> to the CPU.
>
> Below is my implementation using interrupt-map:
> + - interrupt-parent : phandle to the interrupt map subnode
When using interrupt-parent to point at an interrupt map, I believe you
usually just point at the current node; there's no need to a child node.
> + - interrupts : interrupt mapping for LPS331AP interrupt sources:
> + 2 sources: 0 - data ready, 1 - threshold event
> + - irq-map : irq sub-node defining interrupt map
> + (all properties listed below are required):
So, this node isn't required.
> + - #interrupt-cells : should be 1
> + - #address-cells : should be 0
> + - #size-cells : should be 0
There are no addressed entities in this node, so I don't see why those
two properties are needed.
> + - interrupt-map : table of entries consisting of three child elements:
> + - unit_interrupt_specifier - 0 : data ready, 1 : threshold event
> + - interrupt parent phandle
> + - parent unit interrupt specifier consisiting of two elements:
> + - index of the interrupt within the controller
> + - flags : should be 0
It's up to the binding for the node referenced by the phandle to define
how many cells need be present for "flags", and their meaning. This
binding shouldn't attempt to describe those. Equally, the concept of
interrupt-map should be defined elsewwere (e.g.
Documentation/devicetree/bindings/interrupt-controller/interrupts.txt);
it's a generic that shouldn't need duplication in each binding that uses
interrupts.
> +Example:
> +
> +lps331ap@5d {
> + compatible = "st,lps331ap";
> + reg = <0x5d>;
> + drdy-int-pin = /bits/ 8 <2>;
> + interrupt-parent = <&irq_map>;
> + interrupts = <0>, <1>;
> +
> + irq_map: irq-map {
> + #interrupt-cells = <1>;
> + #address-cells = <0>;
> + #size-cells = <0>;
> + interrupt-map = <0 &gpf0 5 0>;
> + };
> +};
>
> And here is how the driver uses this information:
>
> - if interrupt-map is empty then the driver configures
> itself to work without interrupt support
The presence or lack of interrupt support should be driven by the
presence of the interrupts property. interrupt-map should only be used
(if present) to assist in the parsing of the interrupts property.
> - if only one interrupt source is available then the driver
> configures the device to generate data ready interrupts on
> the corresponding INTx pin (in this case the driver must know which
> of the device pins is routed to the cpu -
> st,data-ready-interrupt-pin property conveys this information)
> - if both interrupt sources are available then the driver configures
> the device to generate data ready interrupts on the interrupt pin
> corresponding to the interrupt source with index 0 and event
> interrupts to the interrupt source with index 1.
>
> This solution seems to be a little awkward so I'd like to ask
> if there is any neater way to handle presented requirements.
> The solution must facilitate passing information about two
> interrupt sources two the I2C driver. I have been unable to find
> similar solution in the kernel so far.
Indeed. I think it would be better to work as follows:
interrupts: contains one or two interrupt specifiers. The first entry
always defines the data ready interrupt. The second entry, if present,
defines the threshold event interrupt. This at least allows the
following combinations to be very simple expressed:
* no interrrupts
* just data
* both data and threshold (assuming they're routed to the same parent)
(you could swap the order if it's likely to be more common to have just
a threshold interrupt without any data interrupt).
In order to allow the presence of a threshold interrupt but no data
interrupt, then I think you would need interrupt-map:
lps331ap: lps331ap@5d {
compatible = "st,lps331ap";
reg = <0x5d>;
interrupt-parent = <&lps331ap>;
interrupts = <0>, <1>;
interrupt-map = <0 0>, /* nowhere */
<1 &gpf0 6 0>;
};
In either of those interrupt-map entries, you should be able to set the
phandle to 0 to indicate no interrupt, hence allowing the first entry to
have "no interrupt". Whether that works currently in the code, I have no
idea.
If only the interrupts property were (phandle, args*)*, we could just
set the phandle to 0 in the interrupts property directly. Oh well, roll
on DT 2.0;-)
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
