On 07/05/2013 05:59 PM, Marek Vasut wrote:
> Dear Hector Palacios,
>
>> Dear Marek,
>>
>> On 07/05/2013 01:41 PM, Marek Vasut wrote:
>>> Dear Hector Palacios,
>>>
>>>> Some LRADC channels have a fixed pre-divider, and all can have enabled
>>>> an optional divisor by two which allows a maximum input voltage of
>>>> VDDIO - 50mV.
>>>>
>>>> This patch
>>>>
>>>> - adds the scaling info flag to all channels
>>>> - adds a lookup table with max reference voltage per channel
>>>>
>>>> (where the fixed pre-dividers apply)
>>>>
>>>> - allows to read the scaling attribute (computed from the Vref)
>>>>
>>>> Signed-off-by: Hector Palacios <hector.palacios@xxxxxxxx>
>>>> ---
>>>>
>>>> drivers/staging/iio/adc/mxs-lradc.c | 122
>>>>
>>>> +++++++++++++++++++++++++++--------- 1 file changed, 93 insertions(+),
>>>> 29 deletions(-)
>>>>
>>>> diff --git a/drivers/staging/iio/adc/mxs-lradc.c
>>>> b/drivers/staging/iio/adc/mxs-lradc.c index d65a594..012c42e 100644
>>>> --- a/drivers/staging/iio/adc/mxs-lradc.c
>>>> +++ b/drivers/staging/iio/adc/mxs-lradc.c
>>>> @@ -107,19 +107,63 @@ static const char * const mx28_lradc_irq_names[] =
>>>> {
>>>>
>>>> "mxs-lradc-button1",
>>>>
>>>> };
>>>>
>>>> +/*
>>>> + * Max reference voltage (mV) for each channel
>>>> + */
>>>> +static const int mx23_vref_mv[LRADC_MAX_TOTAL_CHANS] = {
>>>> + 1850, /* CH0 */
>>>> + 1850, /* CH1 */
>>>> + 1850, /* CH2 */
>>>> + 1850, /* CH3 */
>>>> + 1850, /* CH4 */
>>>> + 1850, /* CH5 */
>>>> + 1850 * 2, /* CH6 VDDIO */
>>>> + 1850 * 4, /* CH7 VBATT */
>>>> + 1850, /* CH8 Temp sense 0 */
>>>> + 1850, /* CH9 Temp sense 1 */
>>>> + 1850, /* CH10 */
>>>> + 1850, /* CH11 */
>>>> + 1850, /* CH12 USB_DP */
>>>> + 1850, /* CH13 USB_DN */
>>>> + 1850, /* CH14 VBG */
>>>> + 1850 * 4, /* CH15 VDD5V */
>>>> +};
>>>> +
>>>> +static const int mx28_vref_mv[LRADC_MAX_TOTAL_CHANS] = {
>>>> + 1850, /* CH0 */
>>>> + 1850, /* CH1 */
>>>> + 1850, /* CH2 */
>>>> + 1850, /* CH3 */
>>>> + 1850, /* CH4 */
>>>> + 1850, /* CH5 */
>>>> + 1850, /* CH6 */
>>>> + 1850 * 4, /* CH7 VBATT */
>>>> + 1850, /* CH8 Temp sense 0 */
>>>> + 1850, /* CH9 Temp sense 1 */
>>>> + 1850 * 2, /* CH10 VDDIO */
>>>> + 1850, /* CH11 VTH */
>>>> + 1850 * 2, /* CH12 VDDA */
>>>> + 1850, /* CH13 VDDD */
>>>> + 1850, /* CH14 VBG */
>>>> + 1850 * 4, /* CH15 VDD5V */
>>>> +};
>>>
>>> Should the above not be in DT ?
>>
>> Do you mean for example:
>>
>> lradc@80050000 {
>> compatible = "fsl,imx28-lradc";
>> reg = <0x80050000 0x2000>;
>> interrupts = <10 14 15 16 17 18 19
>> 20 21 22 23 24 25>;
>> vref = <1850 1850 1850 1850
>> 1850 1850 1850 7400
>> 1850 1850 3700 1850
>> 3700 1850 1850 7400>
>> };
>>
>> I'm ok with it, but are there other examples of driver using a similar
>> approach? I see for example the spear-adc which reads:
>>
>> Optional properties:
>> - vref-external: External voltage reference in milli-volts. If omitted
>> the internal voltage reference will be used.
>>
>> which makes me believe the 'internal voltage reference' is hardcoded in the
>> driver. More opinions?
>
> I'd duke this one out on devicetree-discuss@ list. In general, I'd use something
> like fsl,vref prop, but this really better be discussed in a separate thread.
Given timing wrt the merge window we have a couple of months to pin this down
without effecting when it hits mainline so I would go ahead and open a discussion
on devicetree-discuss.
>
> On the other hand, I'd hate to keep these patches here waiting , so maybe we
> should apply them as-is and remove this part from the driver in a subsequent
> patch? What do you say, Lars ?
Could do so but as I said, no particular rush unless people have lots of stuff
they want to do on top of these?
>
> Best regards,
> Marek Vasut
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
