On 05/27/2013 08:12 PM, Sebastian Andrzej Siewior wrote:
> Things that can be done to done without using make up:
That causes some amusing images of code with lipstick ;) 'wake up' perhaps?
> - reduce config_inp from 20 elements to 4
> The loop goes 0…3 so elements 4…19 remain unused.
> - put the shift for analog_line into one line, since config_inp is u32 we
> don't need to worry about sign extension,
> - check if he DT values are 0…3 as expected
> - replace "err = -EINVAL; goto err" with "return -EINVAL;" as there is no
> cleanup and this is less code
> - pull out "config[analog_line[i]][0…3];" from the switch case and use
> magic to the 0…3 correct.
> - since we removed so much lines, spent a few to get
> "config[an_line][wi_order];" done.
> - get rid of "val32, wires_conf" and assign the values directly. This is
> just init code but we can still save a few cycles.
> - remove titsc_config_wires() from resume path. ->bit_yn & friends are only
> written once and not changed so as long as we assume that our DDR will
> have no biflips we can skip that.
>
> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@xxxxxxxxxxxxx>
> ---
> drivers/input/touchscreen/ti_am335x_tsc.c | 124 ++++++++++++-----------------
> 1 file changed, 51 insertions(+), 73 deletions(-)
>
> diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
> index 0dbf3df..96accaa 100644
> --- a/drivers/input/touchscreen/ti_am335x_tsc.c
> +++ b/drivers/input/touchscreen/ti_am335x_tsc.c
> @@ -59,7 +59,7 @@ struct titsc {
> unsigned int bckup_y;
> bool pen_down;
> int steps_to_configure;
> - int config_inp[20];
> + u32 config_inp[4];
> int bit_xp, bit_xn, bit_yp, bit_yn;
> int inp_xp, inp_xn, inp_yp, inp_yn;
> };
> @@ -115,69 +115,54 @@ static int regbit_map(int val)
>
> static int titsc_config_wires(struct titsc *ts_dev)
> {
> - int analog_line[10], wire_order[10];
> - int i, temp_bits, err;
> + u32 analog_line[4];
> + u32 wire_order[4];
> + int i, temp_bits;
>
> for (i = 0; i < 4; i++) {
> /*
> * Get the order in which TSC wires are attached
> * w.r.t. each of the analog input lines on the EVM.
> */
> - analog_line[i] = ts_dev->config_inp[i] & 0xF0;
> - analog_line[i] = analog_line[i] >> 4;
> -
> + analog_line[i] = (ts_dev->config_inp[i] & 0xF0) >> 4;
> wire_order[i] = ts_dev->config_inp[i] & 0x0F;
> + if (WARN_ON(analog_line[i] > 4))
> + return -EINVAL;
> + if (WARN_ON(wire_order[i] > 4))
> + return -EINVAL;
> }
>
> for (i = 0; i < 4; i++) {
> + int an_line;
> + int wi_order;
> +
> + an_line = analog_line[i];
> + wi_order = wire_order[i];
> + temp_bits = config[an_line][wi_order];
> + if (temp_bits == 0)
> + return -EINVAL;
> switch (wire_order[i]) {
> case 0:
> - temp_bits = config[analog_line[i]][0];
> - if (temp_bits == 0) {
> - err = -EINVAL;
> - goto ret;
> - } else {
> - ts_dev->bit_xp = regbit_map(temp_bits);
> - ts_dev->inp_xp = analog_line[i];
> - break;
> - }
> + ts_dev->bit_xp = regbit_map(temp_bits);
> + ts_dev->inp_xp = analog_line[i];
> + break;
> +
> case 1:
> - temp_bits = config[analog_line[i]][1];
> - if (temp_bits == 0) {
> - err = -EINVAL;
> - goto ret;
> - } else {
> - ts_dev->bit_xn = regbit_map(temp_bits);
> - ts_dev->inp_xn = analog_line[i];
> - break;
> - }
> + ts_dev->bit_xn = regbit_map(temp_bits);
> + ts_dev->inp_xn = analog_line[i];
> + break;
> +
> case 2:
> - temp_bits = config[analog_line[i]][2];
> - if (temp_bits == 0) {
> - err = -EINVAL;
> - goto ret;
> - } else {
> - ts_dev->bit_yp = regbit_map(temp_bits);
> - ts_dev->inp_yp = analog_line[i];
> - break;
> - }
> + ts_dev->bit_yp = regbit_map(temp_bits);
> + ts_dev->inp_yp = analog_line[i];
> + break;
> case 3:
> - temp_bits = config[analog_line[i]][3];
> - if (temp_bits == 0) {
> - err = -EINVAL;
> - goto ret;
> - } else {
> - ts_dev->bit_yn = regbit_map(temp_bits);
> - ts_dev->inp_yn = analog_line[i];
> - break;
> - }
> + ts_dev->bit_yn = regbit_map(temp_bits);
> + ts_dev->inp_yn = analog_line[i];
> + break;
> }
> }
> -
> return 0;
> -
> -ret:
> - return err;
> }
>
> static void titsc_step_config(struct titsc *ts_dev)
> @@ -319,7 +304,6 @@ static irqreturn_t titsc_irq(int irq, void *dev)
> unsigned int z1, z2, z;
> unsigned int fsm;
> unsigned int diffx = 0, diffy = 0;
> - int i;
>
> status = titsc_readl(ts_dev, REG_IRQSTATUS);
> if (status & IRQENB_FIFO0THRES) {
> @@ -387,11 +371,10 @@ static irqreturn_t titsc_irq(int irq, void *dev)
> }
>
> static int titsc_parse_dt(struct ti_tscadc_dev *tscadc_dev,
> - struct titsc *ts_dev)
> + struct titsc *ts_dev)
> {
> struct device_node *node = tscadc_dev->dev->of_node;
> - int err, i;
> - u32 val32, wires_conf[4];
> + int err;
>
> if (!node)
> return -EINVAL;
> @@ -399,34 +382,30 @@ static int titsc_parse_dt(struct ti_tscadc_dev *tscadc_dev,
> node = of_get_child_by_name(node, "tsc");
> if (!node)
> return -EINVAL;
> - err = of_property_read_u32(node, "ti,wires", &val32);
> + err = of_property_read_u32(node, "ti,wires", &ts_dev->wires);
> if (err < 0)
> - goto error_ret;
> - ts_dev->wires = val32;
> -
> - err = of_property_read_u32(node,
> - "ti,x-plate-resistance", &val32);
> - if (err < 0)
> - goto error_ret;
> - ts_dev->x_plate_resistance = val32;
> + return err;
> + switch (ts_dev->wires) {
> + case 4:
> + case 5:
> + case 8:
> + break;
> + default:
> + return -EINVAL;
> + }
>
> - err = of_property_read_u32(node,
> - "ti,steps-to-configure", &val32);
> + err = of_property_read_u32(node, "ti,x-plate-resistance",
> + &ts_dev->x_plate_resistance);
> if (err < 0)
> - goto error_ret;
> - ts_dev->steps_to_configure = val32;
> + return err;
>
> - err = of_property_read_u32_array(node, "ti,wire-config",
> - wires_conf, ARRAY_SIZE(wires_conf));
> + err = of_property_read_u32(node, "ti,steps-to-configure",
> + &ts_dev->steps_to_configure);
> if (err < 0)
> - goto error_ret;
> + return err;
>
> - for (i = 0; i < ARRAY_SIZE(wires_conf); i++)
> - ts_dev->config_inp[i] = wires_conf[i];
> - return 0;
> -
> -error_ret:
> - return err;
> + return of_property_read_u32_array(node, "ti,wire-config",
> + ts_dev->config_inp, ARRAY_SIZE(ts_dev->config_inp));
> }
>
> /*
> @@ -545,7 +524,6 @@ static int titsc_resume(struct device *dev)
> 0x00);
> titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
> }
> - titsc_config_wires(ts_dev);
> titsc_step_config(ts_dev);
> titsc_writel(ts_dev, REG_FIFO0THR,
> ts_dev->steps_to_configure);
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
