On 02/01/2013 10:07 AM, Lars-Peter Clausen wrote:
> On 02/01/2013 09:51 AM, Manuel Stahl wrote:
>> This patch adds support for the InvenSense itg3200.
>> The itg3200 is a three-axis gyro with 16-bit ADC and
>> I2C interface.
>>
>> Signed-off-by: Manuel Stahl <manuel.stahl@xxxxxxxxxxxxxxxxx>
>
> Looks good,
>
> Reviewed-by: Lars-Peter Clausen <lars@xxxxxxxxxx>
>
Applied to togreg branch of iio.git - bit of fuzz as we have had lots
of gyroscope activity at the moment, but all trivial.
Thanks,
>> ---
>> drivers/iio/gyro/Kconfig | 8 +
>> drivers/iio/gyro/Makefile | 4 +
>> drivers/iio/gyro/itg3200_buffer.c | 156 ++++++++++++++
>> drivers/iio/gyro/itg3200_core.c | 401 +++++++++++++++++++++++++++++++++++++
>> include/linux/iio/gyro/itg3200.h | 154 ++++++++++++++
>> 5 files changed, 723 insertions(+), 0 deletions(-)
>> create mode 100644 drivers/iio/gyro/itg3200_buffer.c
>> create mode 100644 drivers/iio/gyro/itg3200_core.c
>> create mode 100644 include/linux/iio/gyro/itg3200.h
>>
>> diff --git a/drivers/iio/gyro/Kconfig b/drivers/iio/gyro/Kconfig
>> index 752ac8a..343a3e0 100644
>> --- a/drivers/iio/gyro/Kconfig
>> +++ b/drivers/iio/gyro/Kconfig
>> @@ -30,4 +30,12 @@ config HID_SENSOR_GYRO_3D
>> Say yes here to build support for the HID SENSOR
>> Gyroscope 3D.
>>
>> +config ITG3200
>> + tristate "InvenSense ITG3200 Digital 3-Axis Gyroscope I2C driver"
>> + depends on I2C
>> + select IIO_TRIGGERED_BUFFER if IIO_BUFFER
>> + help
>> + Say yes here to add support for the InvenSense ITG3200 digital
>> + 3-axis gyroscope sensor.
>> +
>> endmenu
>> diff --git a/drivers/iio/gyro/Makefile b/drivers/iio/gyro/Makefile
>> index 9b090ee..99ae7d6 100644
>> --- a/drivers/iio/gyro/Makefile
>> +++ b/drivers/iio/gyro/Makefile
>> @@ -5,3 +5,7 @@
>> obj-$(CONFIG_ADIS16080) += adis16080.o
>> obj-$(CONFIG_ADIS16136) += adis16136.o
>> obj-$(CONFIG_HID_SENSOR_GYRO_3D) += hid-sensor-gyro-3d.o
>> +
>> +itg3200-y := itg3200_core.o
>> +itg3200-$(CONFIG_IIO_BUFFER) += itg3200_buffer.o
>> +obj-$(CONFIG_ITG3200) += itg3200.o
>> diff --git a/drivers/iio/gyro/itg3200_buffer.c b/drivers/iio/gyro/itg3200_buffer.c
>> new file mode 100644
>> index 0000000..f667d2c
>> --- /dev/null
>> +++ b/drivers/iio/gyro/itg3200_buffer.c
>> @@ -0,0 +1,156 @@
>> +/*
>> + * itg3200_buffer.c -- support InvenSense ITG3200
>> + * Digital 3-Axis Gyroscope driver
>> + *
>> + * Copyright (c) 2011 Christian Strobel <christian.strobel@xxxxxxxxxxxxxxxxx>
>> + * Copyright (c) 2011 Manuel Stahl <manuel.stahl@xxxxxxxxxxxxxxxxx>
>> + * Copyright (c) 2012 Thorsten Nowak <thorsten.nowak@xxxxxxxxxxxxxxxxx>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <linux/slab.h>
>> +#include <linux/i2c.h>
>> +#include <linux/interrupt.h>
>> +
>> +#include <linux/iio/iio.h>
>> +#include <linux/iio/buffer.h>
>> +#include <linux/iio/trigger.h>
>> +#include <linux/iio/trigger_consumer.h>
>> +#include <linux/iio/triggered_buffer.h>
>> +#include <linux/iio/gyro/itg3200.h>
>> +
>> +
>> +static int itg3200_read_all_channels(struct i2c_client *i2c, __be16 *buf)
>> +{
>> + u8 tx = 0x80 | ITG3200_REG_TEMP_OUT_H;
>> + struct i2c_msg msg[2] = {
>> + {
>> + .addr = i2c->addr,
>> + .flags = i2c->flags,
>> + .len = 1,
>> + .buf = &tx,
>> + },
>> + {
>> + .addr = i2c->addr,
>> + .flags = i2c->flags | I2C_M_RD,
>> + .len = ITG3200_SCAN_ELEMENTS * sizeof(s16),
>> + .buf = (char *)&buf,
>> + },
>> + };
>> +
>> + return i2c_transfer(i2c->adapter, msg, 2);
>> +}
>> +
>> +static irqreturn_t itg3200_trigger_handler(int irq, void *p)
>> +{
>> + struct iio_poll_func *pf = p;
>> + struct iio_dev *indio_dev = pf->indio_dev;
>> + struct itg3200 *st = iio_priv(indio_dev);
>> + __be16 buf[ITG3200_SCAN_ELEMENTS + sizeof(s64)/sizeof(u16)];
>> +
>> + int ret = itg3200_read_all_channels(st->i2c, buf);
>> + if (ret < 0)
>> + goto error_ret;
>> +
>> + if (indio_dev->scan_timestamp)
>> + memcpy(buf + indio_dev->scan_bytes - sizeof(s64),
>> + &pf->timestamp, sizeof(pf->timestamp));
>> +
>> + iio_push_to_buffers(indio_dev, (u8 *)buf);
>> + iio_trigger_notify_done(indio_dev->trig);
>> +
>> +error_ret:
>> + return IRQ_HANDLED;
>> +}
>> +
>> +int itg3200_buffer_configure(struct iio_dev *indio_dev)
>> +{
>> + return iio_triggered_buffer_setup(indio_dev, &iio_pollfunc_store_time,
>> + itg3200_trigger_handler, NULL);
>> +}
>> +
>> +void itg3200_buffer_unconfigure(struct iio_dev *indio_dev)
>> +{
>> + iio_triggered_buffer_cleanup(indio_dev);
>> +}
>> +
>> +
>> +static int itg3200_data_rdy_trigger_set_state(struct iio_trigger *trig,
>> + bool state)
>> +{
>> + struct iio_dev *indio_dev = trig->private_data;
>> + int ret;
>> + u8 msc;
>> +
>> + ret = itg3200_read_reg_8(indio_dev, ITG3200_REG_IRQ_CONFIG, &msc);
>> + if (ret)
>> + goto error_ret;
>> +
>> + if (state)
>> + msc |= ITG3200_IRQ_DATA_RDY_ENABLE;
>> + else
>> + msc &= ~ITG3200_IRQ_DATA_RDY_ENABLE;
>> +
>> + ret = itg3200_write_reg_8(indio_dev, ITG3200_REG_IRQ_CONFIG, msc);
>> + if (ret)
>> + goto error_ret;
>> +
>> +error_ret:
>> + return ret;
>> +
>> +}
>> +
>> +static const struct iio_trigger_ops itg3200_trigger_ops = {
>> + .owner = THIS_MODULE,
>> + .set_trigger_state = &itg3200_data_rdy_trigger_set_state,
>> +};
>> +
>> +int itg3200_probe_trigger(struct iio_dev *indio_dev)
>> +{
>> + int ret;
>> + struct itg3200 *st = iio_priv(indio_dev);
>> +
>> + st->trig = iio_trigger_alloc("%s-dev%d", indio_dev->name,
>> + indio_dev->id);
>> + if (!st->trig)
>> + return -ENOMEM;
>> +
>> + ret = request_irq(st->i2c->irq,
>> + &iio_trigger_generic_data_rdy_poll,
>> + IRQF_TRIGGER_RISING,
>> + "itg3200_data_rdy",
>> + st->trig);
>> + if (ret)
>> + goto error_free_trig;
>> +
>> +
>> + st->trig->dev.parent = &st->i2c->dev;
>> + st->trig->ops = &itg3200_trigger_ops;
>> + st->trig->private_data = indio_dev;
>> + ret = iio_trigger_register(st->trig);
>> + if (ret)
>> + goto error_free_irq;
>> +
>> + /* select default trigger */
>> + indio_dev->trig = st->trig;
>> +
>> + return 0;
>> +
>> +error_free_irq:
>> + free_irq(st->i2c->irq, st->trig);
>> +error_free_trig:
>> + iio_trigger_free(st->trig);
>> + return ret;
>> +}
>> +
>> +void itg3200_remove_trigger(struct iio_dev *indio_dev)
>> +{
>> + struct itg3200 *st = iio_priv(indio_dev);
>> +
>> + iio_trigger_unregister(st->trig);
>> + free_irq(st->i2c->irq, st->trig);
>> + iio_trigger_free(st->trig);
>> +}
>> diff --git a/drivers/iio/gyro/itg3200_core.c b/drivers/iio/gyro/itg3200_core.c
>> new file mode 100644
>> index 0000000..df2e6aa
>> --- /dev/null
>> +++ b/drivers/iio/gyro/itg3200_core.c
>> @@ -0,0 +1,401 @@
>> +/*
>> + * itg3200_core.c -- support InvenSense ITG3200
>> + * Digital 3-Axis Gyroscope driver
>> + *
>> + * Copyright (c) 2011 Christian Strobel <christian.strobel@xxxxxxxxxxxxxxxxx>
>> + * Copyright (c) 2011 Manuel Stahl <manuel.stahl@xxxxxxxxxxxxxxxxx>
>> + * Copyright (c) 2012 Thorsten Nowak <thorsten.nowak@xxxxxxxxxxxxxxxxx>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + *
>> + * TODO:
>> + * - Support digital low pass filter
>> + * - Support power management
>> + */
>> +
>> +#include <linux/interrupt.h>
>> +#include <linux/irq.h>
>> +#include <linux/i2c.h>
>> +#include <linux/gpio.h>
>> +#include <linux/slab.h>
>> +#include <linux/stat.h>
>> +#include <linux/module.h>
>> +#include <linux/delay.h>
>> +
>> +#include <linux/iio/iio.h>
>> +#include <linux/iio/sysfs.h>
>> +#include <linux/iio/events.h>
>> +#include <linux/iio/buffer.h>
>> +
>> +#include <linux/iio/gyro/itg3200.h>
>> +
>> +
>> +int itg3200_write_reg_8(struct iio_dev *indio_dev,
>> + u8 reg_address, u8 val)
>> +{
>> + struct itg3200 *st = iio_priv(indio_dev);
>> +
>> + return i2c_smbus_write_byte_data(st->i2c, 0x80 | reg_address, val);
>> +}
>> +
>> +int itg3200_read_reg_8(struct iio_dev *indio_dev,
>> + u8 reg_address, u8 *val)
>> +{
>> + struct itg3200 *st = iio_priv(indio_dev);
>> + int ret;
>> +
>> + ret = i2c_smbus_read_byte_data(st->i2c, reg_address);
>> + if (ret < 0)
>> + return ret;
>> + *val = ret;
>> + return 0;
>> +}
>> +
>> +static int itg3200_read_reg_s16(struct iio_dev *indio_dev, u8 lower_reg_address,
>> + int *val)
>> +{
>> + struct itg3200 *st = iio_priv(indio_dev);
>> + struct i2c_client *client = st->i2c;
>> + int ret;
>> + s16 out;
>> +
>> + struct i2c_msg msg[2] = {
>> + {
>> + .addr = client->addr,
>> + .flags = client->flags,
>> + .len = 1,
>> + .buf = (char *)&lower_reg_address,
>> + },
>> + {
>> + .addr = client->addr,
>> + .flags = client->flags | I2C_M_RD,
>> + .len = 2,
>> + .buf = (char *)&out,
>> + },
>> + };
>> +
>> + lower_reg_address |= 0x80;
>> + ret = i2c_transfer(client->adapter, msg, 2);
>> + be16_to_cpus(&out);
>> + *val = out;
>> +
>> + return (ret == 2) ? 0 : ret;
>> +}
>> +
>> +static int itg3200_read_raw(struct iio_dev *indio_dev,
>> + const struct iio_chan_spec *chan,
>> + int *val, int *val2, long info)
>> +{
>> + int ret = 0;
>> + u8 reg;
>> +
>> + switch (info) {
>> + case IIO_CHAN_INFO_RAW:
>> + reg = (u8)chan->address;
>> + ret = itg3200_read_reg_s16(indio_dev, reg, val);
>> + return IIO_VAL_INT;
>> + case IIO_CHAN_INFO_SCALE:
>> + *val = 0;
>> + if (chan->type == IIO_TEMP)
>> + *val2 = 1000000000/280;
>> + else
>> + *val2 = 1214142; /* (1 / 14,375) * (PI / 180) */
>> + return IIO_VAL_INT_PLUS_NANO;
>> + case IIO_CHAN_INFO_OFFSET:
>> + /* Only the temperature channel has an offset */
>> + *val = 23000;
>> + return IIO_VAL_INT;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static ssize_t itg3200_read_frequency(struct device *dev,
>> + struct device_attribute *attr, char *buf)
>> +{
>> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
>> + int ret, sps;
>> + u8 val;
>> +
>> + ret = itg3200_read_reg_8(indio_dev, ITG3200_REG_DLPF, &val);
>> + if (ret)
>> + return ret;
>> +
>> + sps = (val & ITG3200_DLPF_CFG_MASK) ? 1000 : 8000;
>> +
>> + ret = itg3200_read_reg_8(indio_dev, ITG3200_REG_SAMPLE_RATE_DIV, &val);
>> + if (ret)
>> + return ret;
>> +
>> + sps /= val + 1;
>> +
>> + return sprintf(buf, "%d\n", sps);
>> +}
>> +
>> +static ssize_t itg3200_write_frequency(struct device *dev,
>> + struct device_attribute *attr,
>> + const char *buf,
>> + size_t len)
>> +{
>> + struct iio_dev *indio_dev = dev_to_iio_dev(dev);
>> + unsigned val;
>> + int ret;
>> + u8 t;
>> +
>> + ret = kstrtouint(buf, 10, &val);
>> + if (ret)
>> + return ret;
>> +
>> + mutex_lock(&indio_dev->mlock);
>> +
>> + ret = itg3200_read_reg_8(indio_dev, ITG3200_REG_DLPF, &t);
>> + if (ret)
>> + goto err_ret;
>> +
>> + if (val == 0) {
>> + ret = -EINVAL;
>> + goto err_ret;
>> + }
>> + t = ((t & ITG3200_DLPF_CFG_MASK) ? 1000u : 8000u) / val - 1;
>> +
>> + ret = itg3200_write_reg_8(indio_dev, ITG3200_REG_SAMPLE_RATE_DIV, t);
>> +
>> +err_ret:
>> + mutex_unlock(&indio_dev->mlock);
>> +
>> + return ret ? ret : len;
>> +}
>> +
>> +/*
>> + * Reset device and internal registers to the power-up-default settings
>> + * Use the gyro clock as reference, as suggested by the datasheet
>> + */
>> +static int itg3200_reset(struct iio_dev *indio_dev)
>> +{
>> + struct itg3200 *st = iio_priv(indio_dev);
>> + int ret;
>> +
>> + dev_dbg(&st->i2c->dev, "reset device");
>> +
>> + ret = itg3200_write_reg_8(indio_dev,
>> + ITG3200_REG_POWER_MANAGEMENT,
>> + ITG3200_RESET);
>> + if (ret) {
>> + dev_err(&st->i2c->dev, "error resetting device");
>> + goto error_ret;
>> + }
>> +
>> + /* Wait for PLL (1ms according to datasheet) */
>> + udelay(1500);
>> +
>> + ret = itg3200_write_reg_8(indio_dev,
>> + ITG3200_REG_IRQ_CONFIG,
>> + ITG3200_IRQ_ACTIVE_HIGH |
>> + ITG3200_IRQ_PUSH_PULL |
>> + ITG3200_IRQ_LATCH_50US_PULSE |
>> + ITG3200_IRQ_LATCH_CLEAR_ANY);
>> +
>> + if (ret)
>> + dev_err(&st->i2c->dev, "error init device");
>> +
>> +error_ret:
>> + return ret;
>> +}
>> +
>> +/* itg3200_enable_full_scale() - Disables the digital low pass filter */
>> +static int itg3200_enable_full_scale(struct iio_dev *indio_dev)
>> +{
>> + u8 val;
>> + int ret;
>> +
>> + ret = itg3200_read_reg_8(indio_dev, ITG3200_REG_DLPF, &val);
>> + if (ret)
>> + goto err_ret;
>> +
>> + val |= ITG3200_DLPF_FS_SEL_2000;
>> + return itg3200_write_reg_8(indio_dev, ITG3200_REG_DLPF, val);
>> +
>> +err_ret:
>> + return ret;
>> +}
>> +
>> +static int itg3200_initial_setup(struct iio_dev *indio_dev)
>> +{
>> + struct itg3200 *st = iio_priv(indio_dev);
>> + int ret;
>> + u8 val;
>> +
>> + ret = itg3200_read_reg_8(indio_dev, ITG3200_REG_ADDRESS, &val);
>> + if (ret)
>> + goto err_ret;
>> +
>> + if (((val >> 1) & 0x3f) != 0x34) {
>> + dev_err(&st->i2c->dev, "invalid reg value 0x%02x", val);
>> + ret = -ENXIO;
>> + goto err_ret;
>> + }
>> +
>> + ret = itg3200_reset(indio_dev);
>> + if (ret)
>> + goto err_ret;
>> +
>> + ret = itg3200_enable_full_scale(indio_dev);
>> +err_ret:
>> + return ret;
>> +}
>> +
>> +#define ITG3200_TEMP_INFO_MASK (IIO_CHAN_INFO_OFFSET_SHARED_BIT | \
>> + IIO_CHAN_INFO_SCALE_SHARED_BIT | \
>> + IIO_CHAN_INFO_RAW_SEPARATE_BIT)
>> +#define ITG3200_GYRO_INFO_MASK (IIO_CHAN_INFO_SCALE_SHARED_BIT | \
>> + IIO_CHAN_INFO_RAW_SEPARATE_BIT)
>> +
>> +#define ITG3200_ST \
>> + { .sign = 's', .realbits = 16, .storagebits = 16, .endianness = IIO_BE }
>> +
>> +#define ITG3200_GYRO_CHAN(_mod) { \
>> + .type = IIO_ANGL_VEL, \
>> + .modified = 1, \
>> + .channel2 = IIO_MOD_ ## _mod, \
>> + .info_mask = ITG3200_GYRO_INFO_MASK, \
>> + .address = ITG3200_REG_GYRO_ ## _mod ## OUT_H, \
>> + .scan_index = ITG3200_SCAN_GYRO_ ## _mod, \
>> + .scan_type = ITG3200_ST, \
>> +}
>> +
>> +static const struct iio_chan_spec itg3200_channels[] = {
>> + {
>> + .type = IIO_TEMP,
>> + .channel2 = IIO_NO_MOD,
>> + .info_mask = ITG3200_TEMP_INFO_MASK,
>> + .address = ITG3200_REG_TEMP_OUT_H,
>> + .scan_index = ITG3200_SCAN_TEMP,
>> + .scan_type = ITG3200_ST,
>> + },
>> + ITG3200_GYRO_CHAN(X),
>> + ITG3200_GYRO_CHAN(Y),
>> + ITG3200_GYRO_CHAN(Z),
>> + IIO_CHAN_SOFT_TIMESTAMP(ITG3200_SCAN_ELEMENTS),
>> +};
>> +
>> +/* IIO device attributes */
>> +static IIO_DEV_ATTR_SAMP_FREQ(S_IWUSR | S_IRUGO, itg3200_read_frequency,
>> + itg3200_write_frequency);
>> +
>> +static struct attribute *itg3200_attributes[] = {
>> + &iio_dev_attr_sampling_frequency.dev_attr.attr,
>> + NULL
>> +};
>> +
>> +static const struct attribute_group itg3200_attribute_group = {
>> + .attrs = itg3200_attributes,
>> +};
>> +
>> +static const struct iio_info itg3200_info = {
>> + .attrs = &itg3200_attribute_group,
>> + .read_raw = &itg3200_read_raw,
>> + .driver_module = THIS_MODULE,
>> +};
>> +
>> +static const unsigned long itg3200_available_scan_masks[] = { 0xffffffff, 0x0 };
>> +
>> +static int itg3200_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + int ret;
>> + struct itg3200 *st;
>> + struct iio_dev *indio_dev;
>> +
>> + dev_dbg(&client->dev, "probe I2C dev with IRQ %i", client->irq);
>> +
>> + indio_dev = iio_device_alloc(sizeof(*st));
>> + if (indio_dev == NULL) {
>> + ret = -ENOMEM;
>> + goto error_ret;
>> + }
>> +
>> + st = iio_priv(indio_dev);
>> +
>> + i2c_set_clientdata(client, indio_dev);
>> + st->i2c = client;
>> +
>> + indio_dev->dev.parent = &client->dev;
>> + indio_dev->name = client->dev.driver->name;
>> + indio_dev->channels = itg3200_channels;
>> + indio_dev->num_channels = ARRAY_SIZE(itg3200_channels);
>> + indio_dev->available_scan_masks = itg3200_available_scan_masks;
>> + indio_dev->info = &itg3200_info;
>> + indio_dev->modes = INDIO_DIRECT_MODE;
>> +
>> + ret = itg3200_buffer_configure(indio_dev);
>> + if (ret)
>> + goto error_free_dev;
>> +
>> + if (client->irq) {
>> + ret = itg3200_probe_trigger(indio_dev);
>> + if (ret)
>> + goto error_unconfigure_buffer;
>> + }
>> +
>> + ret = itg3200_initial_setup(indio_dev);
>> + if (ret)
>> + goto error_remove_trigger;
>> +
>> + ret = iio_device_register(indio_dev);
>> + if (ret)
>> + goto error_remove_trigger;
>> +
>> + return 0;
>> +
>> +error_remove_trigger:
>> + if (client->irq)
>> + itg3200_remove_trigger(indio_dev);
>> +error_unconfigure_buffer:
>> + itg3200_buffer_unconfigure(indio_dev);
>> +error_free_dev:
>> + iio_device_free(indio_dev);
>> +error_ret:
>> + return ret;
>> +}
>> +
>> +static int itg3200_remove(struct i2c_client *client)
>> +{
>> + struct iio_dev *indio_dev = i2c_get_clientdata(client);
>> +
>> + iio_device_unregister(indio_dev);
>> +
>> + if (client->irq)
>> + itg3200_remove_trigger(indio_dev);
>> +
>> + itg3200_buffer_unconfigure(indio_dev);
>> +
>> + iio_device_free(indio_dev);
>> +
>> + return 0;
>> +}
>> +
>> +static const struct i2c_device_id itg3200_id[] = {
>> + { "itg3200", 0 },
>> + { }
>> +};
>> +MODULE_DEVICE_TABLE(i2c, itg3200_id);
>> +
>> +static struct i2c_driver itg3200_driver = {
>> + .driver = {
>> + .owner = THIS_MODULE,
>> + .name = "itg3200",
>> + },
>> + .id_table = itg3200_id,
>> + .probe = itg3200_probe,
>> + .remove = itg3200_remove,
>> +};
>> +
>> +module_i2c_driver(itg3200_driver);
>> +
>> +MODULE_AUTHOR("Christian Strobel <christian.strobel@xxxxxxxxxxxxxxxxx>");
>> +MODULE_DESCRIPTION("ITG3200 Gyroscope I2C driver");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/include/linux/iio/gyro/itg3200.h b/include/linux/iio/gyro/itg3200.h
>> new file mode 100644
>> index 0000000..c53f169
>> --- /dev/null
>> +++ b/include/linux/iio/gyro/itg3200.h
>> @@ -0,0 +1,154 @@
>> +/*
>> + * itg3200.h -- support InvenSense ITG3200
>> + * Digital 3-Axis Gyroscope driver
>> + *
>> + * Copyright (c) 2011 Christian Strobel <christian.strobel@xxxxxxxxxxxxxxxxx>
>> + * Copyright (c) 2011 Manuel Stahl <manuel.stahl@xxxxxxxxxxxxxxxxx>
>> + * Copyright (c) 2012 Thorsten Nowak <thorsten.nowak@xxxxxxxxxxxxxxxxx>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#ifndef I2C_ITG3200_H_
>> +#define I2C_ITG3200_H_
>> +
>> +#include <linux/iio/iio.h>
>> +
>> +/* Register with I2C address (34h) */
>> +#define ITG3200_REG_ADDRESS 0x00
>> +
>> +/* Sample rate divider
>> + * Range: 0 to 255
>> + * Default value: 0x00 */
>> +#define ITG3200_REG_SAMPLE_RATE_DIV 0x15
>> +
>> +/* Digital low pass filter settings */
>> +#define ITG3200_REG_DLPF 0x16
>> +/* DLPF full scale range */
>> +#define ITG3200_DLPF_FS_SEL_2000 0x18
>> +/* Bandwidth (Hz) and internal sample rate
>> + * (kHz) of DLPF */
>> +#define ITG3200_DLPF_256_8 0x00
>> +#define ITG3200_DLPF_188_1 0x01
>> +#define ITG3200_DLPF_98_1 0x02
>> +#define ITG3200_DLPF_42_1 0x03
>> +#define ITG3200_DLPF_20_1 0x04
>> +#define ITG3200_DLPF_10_1 0x05
>> +#define ITG3200_DLPF_5_1 0x06
>> +
>> +#define ITG3200_DLPF_CFG_MASK 0x07
>> +
>> +/* Configuration for interrupt operations */
>> +#define ITG3200_REG_IRQ_CONFIG 0x17
>> +/* Logic level */
>> +#define ITG3200_IRQ_ACTIVE_LOW 0x80
>> +#define ITG3200_IRQ_ACTIVE_HIGH 0x00
>> +/* Drive type */
>> +#define ITG3200_IRQ_OPEN_DRAIN 0x40
>> +#define ITG3200_IRQ_PUSH_PULL 0x00
>> +/* Latch mode */
>> +#define ITG3200_IRQ_LATCH_UNTIL_CLEARED 0x20
>> +#define ITG3200_IRQ_LATCH_50US_PULSE 0x00
>> +/* Latch clear method */
>> +#define ITG3200_IRQ_LATCH_CLEAR_ANY 0x10
>> +#define ITG3200_IRQ_LATCH_CLEAR_STATUS 0x00
>> +/* Enable interrupt when device is ready */
>> +#define ITG3200_IRQ_DEVICE_RDY_ENABLE 0x04
>> +/* Enable interrupt when data is available */
>> +#define ITG3200_IRQ_DATA_RDY_ENABLE 0x01
>> +
>> +/* Determine the status of ITG-3200 interrupts */
>> +#define ITG3200_REG_IRQ_STATUS 0x1A
>> +/* Status of 'device is ready'-interrupt */
>> +#define ITG3200_IRQ_DEVICE_RDY_STATUS 0x04
>> +/* Status of 'data is available'-interrupt */
>> +#define ITG3200_IRQ_DATA_RDY_STATUS 0x01
>> +
>> +/* Sensor registers */
>> +#define ITG3200_REG_TEMP_OUT_H 0x1B
>> +#define ITG3200_REG_TEMP_OUT_L 0x1C
>> +#define ITG3200_REG_GYRO_XOUT_H 0x1D
>> +#define ITG3200_REG_GYRO_XOUT_L 0x1E
>> +#define ITG3200_REG_GYRO_YOUT_H 0x1F
>> +#define ITG3200_REG_GYRO_YOUT_L 0x20
>> +#define ITG3200_REG_GYRO_ZOUT_H 0x21
>> +#define ITG3200_REG_GYRO_ZOUT_L 0x22
>> +
>> +/* Power management */
>> +#define ITG3200_REG_POWER_MANAGEMENT 0x3E
>> +/* Reset device and internal registers to the
>> + * power-up-default settings */
>> +#define ITG3200_RESET 0x80
>> +/* Enable low power sleep mode */
>> +#define ITG3200_SLEEP 0x40
>> +/* Put according gyroscope in standby mode */
>> +#define ITG3200_STANDBY_GYRO_X 0x20
>> +#define ITG3200_STANDBY_GYRO_Y 0x10
>> +#define ITG3200_STANDBY_GYRO_Z 0x08
>> +/* Determine the device clock source */
>> +#define ITG3200_CLK_INTERNAL 0x00
>> +#define ITG3200_CLK_GYRO_X 0x01
>> +#define ITG3200_CLK_GYRO_Y 0x02
>> +#define ITG3200_CLK_GYRO_Z 0x03
>> +#define ITG3200_CLK_EXT_32K 0x04
>> +#define ITG3200_CLK_EXT_19M 0x05
>> +
>> +
>> +/**
>> + * struct itg3200 - device instance specific data
>> + * @i2c: actual i2c_client
>> + * @trig: data ready trigger from itg3200 pin
>> + **/
>> +struct itg3200 {
>> + struct i2c_client *i2c;
>> + struct iio_trigger *trig;
>> +};
>> +
>> +enum ITG3200_SCAN_INDEX {
>> + ITG3200_SCAN_TEMP,
>> + ITG3200_SCAN_GYRO_X,
>> + ITG3200_SCAN_GYRO_Y,
>> + ITG3200_SCAN_GYRO_Z,
>> + ITG3200_SCAN_ELEMENTS,
>> +};
>> +
>> +int itg3200_write_reg_8(struct iio_dev *indio_dev,
>> + u8 reg_address, u8 val);
>> +
>> +int itg3200_read_reg_8(struct iio_dev *indio_dev,
>> + u8 reg_address, u8 *val);
>> +
>> +
>> +#ifdef CONFIG_IIO_BUFFER
>> +
>> +void itg3200_remove_trigger(struct iio_dev *indio_dev);
>> +int itg3200_probe_trigger(struct iio_dev *indio_dev);
>> +
>> +int itg3200_buffer_configure(struct iio_dev *indio_dev);
>> +void itg3200_buffer_unconfigure(struct iio_dev *indio_dev);
>> +
>> +#else /* CONFIG_IIO_BUFFER */
>> +
>> +static inline void itg3200_remove_trigger(struct iio_dev *indio_dev)
>> +{
>> +}
>> +
>> +static inline int itg3200_probe_trigger(struct iio_dev *indio_dev)
>> +{
>> + return 0;
>> +}
>> +
>> +static inline int itg3200_buffer_configure(struct iio_dev *indio_dev)
>> +{
>> + return 0;
>> +}
>> +
>> +static inline void itg3200_buffer_unconfigure(struct iio_dev *indio_dev)
>> +{
>> +}
>> +
>> +#endif /* CONFIG_IIO_RING_BUFFER */
>> +
>> +#endif /* ITG3200_H_ */
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
