On 04/04/2012 05:40 PM, Jon Brenner wrote: > Jonathon, > > You wrote; > <snip> > Units don't look right for sampling frequency. Sorry, but that's an abi > > issue so even if it is > fiddly to do the conversion to Hz it needs to be done. > </snip> > > Need some help here. > In the tsl2x7x driver sampling frequency is being used for setting > "persistence register". > It's actually a H/W filter. Gah, you mentioned this before and I meant to look back at the previous times we have hit this particular type of control (it's pretty common!) > Here is an abstract from the data sheet: > -- > Persistence Register (0x0C) > The persistence register controls the filtering interrupt capabilities > of the device. Configurable filtering is > provided to allow interrupts to be generated after each ADC integration > cycle or if the ADC integration has > produced a result that is outside of the values specified by threshold > register for some specified amount of time. > Separate filtering is provided for proximity and ALS functions. ALS > interrupts are generated using C0DATA. > -- > The value provided here by the ABI is actually the number of > 'consecutive values out of range'. > > The H/W takes care of counting the consecutive values out of range and > issues and interrupt when reached. > > The timing (or frequency) of these out of range values are based on the > ALS or Prox integration time (determined by that respective setting). > That being the case a fixed table of sampling "frequencies" cannot be > reasonably defined - as the frequency can vary widely, based on other > settings. > > So the register really is set to the desired number of 'values out of > range'. > To add another slight twist, the value (number of out of range) > increases by 1 until 5, then by 5 until 60 - with the caveat that a > value of 0 generates an interrupt every ALS or Prox integration cycle . > > Since the sysfs-bus-iio doc contained a close match with respect to the > operation: > Description: > Some devices have internal clocks. This parameter sets > the > resulting sampling frequency. In many devices this > parameter has an effect on input filters etc rather than > simply controlling when the input is sampled. As this > effects datardy triggers, hardware buffers and the sysfs > direct access interfaces, it may be found in any of the > relevant directories. If it effects all of the above > then it is to be found in the base device directory. > > Thus we used "sampling_frequency" - but now I am wondering if it should > be something else. > > If this is better suited for a different ABI please tell me what that > would be. I'd argue this should really be sampling frequency anyway. It's actually a common enough thing to see. I was sure we'd hit this before and indeed we did with the tmd277711 driver back in 2010 (hit the mailing list archives for that one). Dongguen Kim was the author (cc'd). Actually grep shows that my own sca3000 driver has this too (it's been a while!) It's actually made it through in the abi docs for all sorts of event types though I think the only correct user is the sca3000 accelerometer. Description is... Period of time (in seconds) for which the condition must be met before an event is generated. If direction is not specified then this period applies to both directions. I know it is annoying that this parameter in side the device is very heavily dependent on other controls (often the case with this sort of thing) but to have a remotely consistent interface we have to define a standard unit. Hence the 'right' way to handle this is to have a cached value in seconds and then work out the nearest possible setting when ever anything else that effects it is changed. Fiddly, but we are playing this game all over the place in other drivers. So here you are going to have in_intensity0_thresh_period and in_proximity0_thresh_period Both probably taking values as INT_PLUS_MICRO. Note that we have other filters controls for events such as hysterisis which is common on raw adc's. Jonathan > > Please help! > > Jon > -- > To unsubscribe from this list: send the line "unsubscribe linux-iio" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html