On 03/23/11 01:07, Jon Brenner wrote: > Jonathan, et al, > > Again, thank you for taking the time to review the latest submission. > I have implemented all recommendations made (with the exceptions noted below). > > I have also added two new functions (not seen here): > 'taos_suspend', and 'taos_resume' > > These changes and comments will be submitted in the next patch [PATCH V3] submission which I will submit shortly (after testing/verification). > > Respectfully, > Jon > > -----Original Message----- > As I pm'd you the other day, please remember to make version of patch clear in title, and include details of what has changed since previous version. > OK - NEXT PATCH WILL INDICATE VERSION 3 > > WILL REMOVE SENSORS_ PREFIX FROM KCONFIG & MAKEFILE > > ADDED/MOVED/CREATED DOCUMENTATION AS RECOMMENDED > > ----- snip ------------ >> +/* >> + * Provides initial operational parameter defaults. >> + * These defaults may be changed through the device's sysfs files. >> + */ > How about pasing in taos_settings and making all of this func a bit more readable? > PREFER TO USE DEFAULTS METHOD Ah, I didn't make clear what I meant here. It was simply an observation that having static void taos_defaults(struct taos_settings *settings) { settings->als_time = 450; etc. } would be easier to read. > >> +static void taos_defaults(struct tsl2583_chip *chip) { >> + /* Operational parameters */ >> + chip->taos_settings.als_time = 450; >> + /* must be a multiple of 50mS */ >> + chip->taos_settings.als_gain = 2; >> + /* this is actually an index into the gain table */ >> + /* assume clear glass as default */ >> + chip->taos_settings.als_gain_trim = 1000; >> + /* default gain trim to account for aperture effects */ >> + chip->taos_settings.als_cal_target = 130; >> + /* Known external ALS reading used for calibration */ } >> + > > ----- snip ------------ >> + if ((ch0 >= chip->als_saturation) || (ch1 >= chip->als_saturation)) > would be easier to read if you set ret to lux max here an avoid jumping into > the if statement below. > NO - TSL258X_LUX_CALC_OVER_FLOW NEEDS TO PASSED UP. > MUTEX NEEDS TO BE UNLOCKED. > THEN RETURN. Sorry, should have said jump to out_unlock having set ret = LUX_CALC_OVER_FLOW; Just makes for marginally cleaner program flow to my mind (though I don't really care about this one). >> + goto return_max; > > ----- snip ------------ > &taos_device_lux[0] perhaps? > NO - CAST MAKES IT MORE OBVIOUS - at least to me ;-) >> + for (p = (struct taos_lux *) taos_device_lux; > > ----- snip ------------ >> + > If not time critical lest make that a sleep. > NO - TIME IS REQUIRED FOR DEVICE TO SETTLE BETWEEN POWERON AND ADC ENABLE - DON'T WANT TO MAKE IT ANY LONGER THAN NECESSARY. But do you want to spin the processor during this time instead of getting on with something useful? I guess it depends on how critical speed is in the taos_chip_on function. I'd say this device is slow enough that a possible extra delay doesn't really matter. >> + mdelay(3); >> + /* NOW enable the ADC > > > ----- snip ------------ > I still wonder if there isn't a way of avoiding this index issue. > It's horrible and really feels like something we ought to able > to handle reasonably well... > BECAUSE THE CH0 AND CH1 DIVERGE AT HIGH GAINS -- INDEX IS BETTER THAN USING CHO OR CH1 VALUE > ( AS EITHER ONE OVER THE OTHER WOULD BE WRONG :-{ ) I can see your point to a certain extent. The counter argument is that doing it with an index precludes ever touching this with any remotely general purpose user space code. Given it's an internal gain anyway is the precise value that critical? Basically is user space ever going to care about the difference between those those values? Another option would be to have a gain for each channel as separate attributes (clearly writing to one would change the other). >> + if (value > 3) { >> + dev_err(dev, "Invalid Gain Index: Enter 0-3\n"); >> + return -1; >> + } else { >> + chip->taos_settings.als_gain = value; >> + } >> + return len; >> +} > > ----- snip ------------ > Just to confirm, is this a frequency in Hz? If it is > can we renaming it to taos_als_frequency_show to > avoid confusing me? > > THIS IS THE INTERNAL ALS INTEGRATION TIME FOR THE ADC CHANNELS > I SHOE HORNED IT INTO SAMPLING FREQUENCY TO HELP ALEVIATE THE ABI ANGST That's good but it does have to match the units specified in the ABI as well. > >> +static ssize_t taos_als_time_show(struct device *dev, >> + struct device_attribute *attr, char *buf) >> +{ >> + struct iio_dev *indio_dev = dev_get_drvdata(dev); >> + struct tsl2583_chip *chip = indio_dev->dev_data; >> + >> + return sprintf(buf, "%d\n", chip->taos_settings.als_time); >> +} > > ----- snip ------------ > scale as a stand alone attribute isn't defined. Please document this. > Looking at what you do with it, it's another factor effecting the overal > gain on the reading that reaches userspace. Ideally you'd roll this > into your calibscale parameter, but I can see that would get complex > to manage. Will have a think about this. In devices with a simple conversion > function (adc's etc) we handle this by leaving this software value > be applied by userspace (and output it as in_scale). The issue here that > as far as userspace is concerned both of your scales have been applied before > it sees the data and at different more or less random looking points in > the calculation. > > Actually, looking at the calculation you could output illuminance0_raw > and let userspace apply a multiplier based on your trim value and offset > +0.5? If you want to hold trim in driver then just implement > read and write to > > illuminance0_scale > and have read only > illuminance0_offset (rather tediously for this device, offset is applied > before scale, so you'll need to divide 0.5 by whatever your trim is). > > We'll have to do pin down how to do this before moving out of staging > so best to get it right now. > > CHANGED TO ILLUMINANCE0_SCALE > > LIFE WOULE BE NICE IF WE COULD JUST PASS THE RAW DATA UP TO USERSPACE > BUT WE HAVE CUSTOMERS WHO REQUIRE IT TO COME UP CALCULATED WITH > THE MULTIPLIER FACTORED IN Sure. It's a fiddly calculation so I can kind of see their point. These light sensors are all a pain :) > > ----- snip ------------ >> + for (i = 0; i < MAX_DEVICE_REGS; i++) { >> + ret = i2c_smbus_write_byte(clientp, >> + (TSL258X_CMD_REG | (TSL258X_CNTRL + i))); >> + if (ret < 0) { >> + dev_err(&clientp->dev, "i2c_smbus_write_byte() to cmd " >> + "reg failed in taos_probe(), err = %d\n", ret); >> + goto fail1; >> + } >> + buf[i] = i2c_smbus_read_byte(clientp); > error handling for this read? > VALUE IS UNIMPORTANT - BUT MAKING SURE WE CAN JUST READ ALL 32 REGISTER LOCATIONS IS.. > > ----- snip ------------ > >> + } >> + if (!taos_skate_device(buf)) { >> + dev_info(&clientp->dev, "i2c device found but does not match " >> + "expected id in taos_probe()\n"); >> + goto fail1; >> + } else { > The sort of debug info you want to get rid of for production drivers. Doesn't > tell anyone anything helpful. > NO - DO NOT AGREE - IF A CUSTOMER EXPECTS ONE DEVICE BUT HAS SOMEHOW INSTALLED A DIFFERENT ONE > AT PRODUCTION TIME, THIS WILL HELP IDENTIFY THE ISSUE. > (IE. WANTED A TAOS ALS DEVICE BUT INSTALLED A TAOS PROX/ALS DEVICE) > FIRST PART INDICATES THAT. SECOND PART IS CONFIRMATION THAT DEVICE WAS IDENTIFIED TO SYSTEM. I'm happy with the error one. Just don't see the point in saying 'everything is as expected'. The mere absence of the error indicates that just fine! Jonathan -- To unsubscribe from this list: send the line "unsubscribe linux-iio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html