On 1/8/24 03:02, Phillip Susi wrote:
> Disks with Power Up In Standby enabled that required the
> SET FEATURES command to start up were being issued the
> command during resume. Recently this was extended to
> include PuiS disks that don't require the SET FEATURES
> command. Suppress this and leave the disk in standby
> until the disk is actually accessed.
Please use full 72-char lines for commit messages. The commit message also does
not clearly describe what the patch does (completely silent on forcing the drive
to sleep).
But this patch is anyway not acceptable (see below) and out of place in this
series (it is not about sleep).
> ---
> drivers/ata/libata-core.c | 32 ++++++++++++++++++++++++++++----
> drivers/ata/libata-eh.c | 12 +++++++++++-
> drivers/ata/libata.h | 1 +
> include/linux/libata.h | 1 +
> 4 files changed, 41 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
> index ef6a2349a6f8..f758fc88ac19 100644
> --- a/drivers/ata/libata-core.c
> +++ b/drivers/ata/libata-core.c
> @@ -1912,7 +1912,30 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
> goto err_out;
> }
>
> - if (!tried_spinup && (id[2] == 0x37c8 || id[2] == 0x738c)) {
> + if (flags & ATA_READID_NOSTART && id[2] == 0x37c8)
> + {
> + /*
> + * The drive has powered up in standby, and returned incomplete IDENTIFY info
> + * so we can't revalidate it yet. We have also been asked to avoid starting the
> + * drive, so stop here and leave the drive asleep and the EH pending, to be
> + * restarted on later I/O request
> + */
> +#if 0
> + ata_tf_init(dev, &tf);
> + tf.flags |= ATA_TFLAG_DEVICE | ATA_TFLAG_ISADDR;
> + tf.protocol = ATA_PROT_NODATA;
> + tf.command = ATA_CMD_SLEEP;
> + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
> + ata_dev_info(dev, "PuiS detected, putting drive to sleep");
I already commented that this is not following the ACS specifications and thus
should not be done. So again, nack.
> +#else
> + dev->flags |= ATA_DFLAG_SLEEPING;
> + ata_dev_info(dev, "PuiS detected, leaving drive in standby");
> +#endif
> + return -EAGAIN;
> + }
> +
> + if (!(flags & ATA_READID_NOSTART) &&
> + !tried_spinup && (id[2] == 0x37c8 || id[2] == 0x738c)) {
> tried_spinup = 1;
> /*
> * Drive powered-up in standby mode, and requires a specific
> @@ -3969,6 +3992,8 @@ int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class,
>
> /* re-read ID */
> rc = ata_dev_reread_id(dev, readid_flags);
> + if (rc == -EAGAIN)
> + return rc;
> if (rc)
> goto fail;
>
> @@ -5241,8 +5266,7 @@ static void ata_port_suspend(struct ata_port *ap, pm_message_t mesg,
> * http://thread.gmane.org/gmane.linux.ide/46764
> */
> ata_port_request_pm(ap, mesg, 0,
> - ATA_EHI_QUIET | ATA_EHI_NO_AUTOPSY |
> - ATA_EHI_NO_RECOVERY,
> + ATA_EHI_QUIET | ATA_EHI_NO_AUTOPSY | ATA_EHI_NO_RECOVERY,
> async);
> }
>
> @@ -5279,7 +5303,7 @@ static void ata_port_resume(struct ata_port *ap, pm_message_t mesg,
> bool async)
> {
> ata_port_request_pm(ap, mesg, ATA_EH_RESET | ATA_EH_SET_ACTIVE,
> - ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET,
> + ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET | ATA_EHI_NOSTART,
> async);
> }
>
> diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
> index 799a1b8bc384..e45e60112951 100644
> --- a/drivers/ata/libata-eh.c
> +++ b/drivers/ata/libata-eh.c
> @@ -22,6 +22,7 @@
> #include <scsi/scsi_cmnd.h>
> #include <scsi/scsi_dbg.h>
> #include "../scsi/scsi_transport_api.h"
> +#include <linux/pm_runtime.h>
>
> #include <linux/libata.h>
>
> @@ -3046,6 +3047,8 @@ static int ata_eh_revalidate_and_attach(struct ata_link *link,
>
> if (ehc->i.flags & ATA_EHI_DID_RESET)
> readid_flags |= ATA_READID_POSTRESET;
> + if (ehc->i.flags & ATA_EHI_NOSTART)
> + readid_flags |= ATA_READID_NOSTART;
>
> if ((action & ATA_EH_REVALIDATE) && ata_dev_enabled(dev)) {
> WARN_ON(dev->class == ATA_DEV_PMP);
> @@ -3075,8 +3078,15 @@ static int ata_eh_revalidate_and_attach(struct ata_link *link,
> ata_eh_about_to_do(link, dev, ATA_EH_REVALIDATE);
> rc = ata_dev_revalidate(dev, ehc->classes[dev->devno],
> readid_flags);
> - if (rc)
> + if (rc == -EAGAIN) {
> + rc = 0; /* start required but suppressed, handle later */
> + ehc->i.dev_action[dev->devno] &= ~ATA_EH_SET_ACTIVE;
> + continue;
> + }
> + else if (rc)
> + {
> goto err;
> + }
>
> ata_eh_done(link, dev, ATA_EH_REVALIDATE);
>
> diff --git a/drivers/ata/libata.h b/drivers/ata/libata.h
> index 43ad1ef9b63a..cff3facad055 100644
> --- a/drivers/ata/libata.h
> +++ b/drivers/ata/libata.h
> @@ -19,6 +19,7 @@
> enum {
> /* flags for ata_dev_read_id() */
> ATA_READID_POSTRESET = (1 << 0), /* reading ID after reset */
> + ATA_READID_NOSTART = (1 << 1), /* do not start drive */
>
> /* selector for ata_down_xfermask_limit() */
> ATA_DNXFER_PIO = 0, /* speed down PIO */
> diff --git a/include/linux/libata.h b/include/linux/libata.h
> index 1dbb14daccfa..50d6fa933946 100644
> --- a/include/linux/libata.h
> +++ b/include/linux/libata.h
> @@ -328,6 +328,7 @@ enum {
>
> /* ata_eh_info->flags */
> ATA_EHI_HOTPLUGGED = (1 << 0), /* could have been hotplugged */
> + ATA_EHI_NOSTART = (1 << 1), /* don't start the disk */
> ATA_EHI_NO_AUTOPSY = (1 << 2), /* no autopsy */
> ATA_EHI_QUIET = (1 << 3), /* be quiet */
> ATA_EHI_NO_RECOVERY = (1 << 4), /* no recovery */
--
Damien Le Moal
Western Digital Research
