v2 changes:
- fix typos in changelog
- change PORT_CMD_ICC_* constants as well
- include linux/bits.h
---
drivers/ata/ahci.h | 245 +++++++++++++++++++++++----------------------
1 file changed, 123 insertions(+), 122 deletions(-)
diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index 7add8e79912b..ff8e6ae1c636 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -24,6 +24,7 @@
#include <linux/libata.h>
#include <linux/phy/phy.h>
#include <linux/regulator/consumer.h>
+#include <linux/bits.h>
/* Enclosure Management Control */
#define EM_CTRL_MSG_TYPE 0x000f0000
@@ -53,12 +54,12 @@ enum {
AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ +
AHCI_CMD_TBL_AR_SZ +
(AHCI_RX_FIS_SZ * 16),
- AHCI_IRQ_ON_SG = (1 << 31),
- AHCI_CMD_ATAPI = (1 << 5),
- AHCI_CMD_WRITE = (1 << 6),
- AHCI_CMD_PREFETCH = (1 << 7),
- AHCI_CMD_RESET = (1 << 8),
- AHCI_CMD_CLR_BUSY = (1 << 10),
+ AHCI_IRQ_ON_SG = BIT(31),
+ AHCI_CMD_ATAPI = BIT(5),
+ AHCI_CMD_WRITE = BIT(6),
+ AHCI_CMD_PREFETCH = BIT(7),
+ AHCI_CMD_RESET = BIT(8),
+ AHCI_CMD_CLR_BUSY = BIT(10),
RX_FIS_PIO_SETUP = 0x20, /* offset of PIO Setup FIS data */
RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */
@@ -76,37 +77,37 @@ enum {
HOST_CAP2 = 0x24, /* host capabilities, extended */
/* HOST_CTL bits */
- HOST_RESET = (1 << 0), /* reset controller; self-clear */
- HOST_IRQ_EN = (1 << 1), /* global IRQ enable */
- HOST_MRSM = (1 << 2), /* MSI Revert to Single Message */
- HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
+ HOST_RESET = BIT(0), /* reset controller; self-clear */
+ HOST_IRQ_EN = BIT(1), /* global IRQ enable */
+ HOST_MRSM = BIT(2), /* MSI Revert to Single Message */
+ HOST_AHCI_EN = BIT(31), /* AHCI enabled */
/* HOST_CAP bits */
- HOST_CAP_SXS = (1 << 5), /* Supports External SATA */
- HOST_CAP_EMS = (1 << 6), /* Enclosure Management support */
- HOST_CAP_CCC = (1 << 7), /* Command Completion Coalescing */
- HOST_CAP_PART = (1 << 13), /* Partial state capable */
- HOST_CAP_SSC = (1 << 14), /* Slumber state capable */
- HOST_CAP_PIO_MULTI = (1 << 15), /* PIO multiple DRQ support */
- HOST_CAP_FBS = (1 << 16), /* FIS-based switching support */
- HOST_CAP_PMP = (1 << 17), /* Port Multiplier support */
- HOST_CAP_ONLY = (1 << 18), /* Supports AHCI mode only */
- HOST_CAP_CLO = (1 << 24), /* Command List Override support */
- HOST_CAP_LED = (1 << 25), /* Supports activity LED */
- HOST_CAP_ALPM = (1 << 26), /* Aggressive Link PM support */
- HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
- HOST_CAP_MPS = (1 << 28), /* Mechanical presence switch */
- HOST_CAP_SNTF = (1 << 29), /* SNotification register */
- HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
- HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
+ HOST_CAP_SXS = BIT(5), /* Supports External SATA */
+ HOST_CAP_EMS = BIT(6), /* Enclosure Management support */
+ HOST_CAP_CCC = BIT(7), /* Command Completion Coalescing */
+ HOST_CAP_PART = BIT(13), /* Partial state capable */
+ HOST_CAP_SSC = BIT(14), /* Slumber state capable */
+ HOST_CAP_PIO_MULTI = BIT(15), /* PIO multiple DRQ support */
+ HOST_CAP_FBS = BIT(16), /* FIS-based switching support */
+ HOST_CAP_PMP = BIT(17), /* Port Multiplier support */
+ HOST_CAP_ONLY = BIT(18), /* Supports AHCI mode only */
+ HOST_CAP_CLO = BIT(24), /* Command List Override support */
+ HOST_CAP_LED = BIT(25), /* Supports activity LED */
+ HOST_CAP_ALPM = BIT(26), /* Aggressive Link PM support */
+ HOST_CAP_SSS = BIT(27), /* Staggered Spin-up */
+ HOST_CAP_MPS = BIT(28), /* Mechanical presence switch */
+ HOST_CAP_SNTF = BIT(29), /* SNotification register */
+ HOST_CAP_NCQ = BIT(30), /* Native Command Queueing */
+ HOST_CAP_64 = BIT(31), /* PCI DAC (64-bit DMA) support */
/* HOST_CAP2 bits */
- HOST_CAP2_BOH = (1 << 0), /* BIOS/OS handoff supported */
- HOST_CAP2_NVMHCI = (1 << 1), /* NVMHCI supported */
- HOST_CAP2_APST = (1 << 2), /* Automatic partial to slumber */
- HOST_CAP2_SDS = (1 << 3), /* Support device sleep */
- HOST_CAP2_SADM = (1 << 4), /* Support aggressive DevSlp */
- HOST_CAP2_DESO = (1 << 5), /* DevSlp from slumber only */
+ HOST_CAP2_BOH = BIT(0), /* BIOS/OS handoff supported */
+ HOST_CAP2_NVMHCI = BIT(1), /* NVMHCI supported */
+ HOST_CAP2_APST = BIT(2), /* Automatic partial to slumber */
+ HOST_CAP2_SDS = BIT(3), /* Support device sleep */
+ HOST_CAP2_SADM = BIT(4), /* Support aggressive DevSlp */
+ HOST_CAP2_DESO = BIT(5), /* DevSlp from slumber only */
/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
@@ -128,24 +129,24 @@ enum {
PORT_DEVSLP = 0x44, /* device sleep */
/* PORT_IRQ_{STAT,MASK} bits */
- PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
- PORT_IRQ_TF_ERR = (1 << 30), /* task file error */
- PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */
- PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */
- PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */
- PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */
- PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */
- PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
-
- PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
- PORT_IRQ_DMPS = (1 << 7), /* mechanical presence status */
- PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
- PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */
- PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */
- PORT_IRQ_SDB_FIS = (1 << 3), /* Set Device Bits FIS rx'd */
- PORT_IRQ_DMAS_FIS = (1 << 2), /* DMA Setup FIS rx'd */
- PORT_IRQ_PIOS_FIS = (1 << 1), /* PIO Setup FIS rx'd */
- PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */
+ PORT_IRQ_COLD_PRES = BIT(31), /* cold presence detect */
+ PORT_IRQ_TF_ERR = BIT(30), /* task file error */
+ PORT_IRQ_HBUS_ERR = BIT(29), /* host bus fatal error */
+ PORT_IRQ_HBUS_DATA_ERR = BIT(28), /* host bus data error */
+ PORT_IRQ_IF_ERR = BIT(27), /* interface fatal error */
+ PORT_IRQ_IF_NONFATAL = BIT(26), /* interface non-fatal error */
+ PORT_IRQ_OVERFLOW = BIT(24), /* xfer exhausted available S/G */
+ PORT_IRQ_BAD_PMP = BIT(23), /* incorrect port multiplier */
+
+ PORT_IRQ_PHYRDY = BIT(22), /* PhyRdy changed */
+ PORT_IRQ_DMPS = BIT(7), /* mechanical presence status */
+ PORT_IRQ_CONNECT = BIT(6), /* port connect change status */
+ PORT_IRQ_SG_DONE = BIT(5), /* descriptor processed */
+ PORT_IRQ_UNK_FIS = BIT(4), /* unknown FIS rx'd */
+ PORT_IRQ_SDB_FIS = BIT(3), /* Set Device Bits FIS rx'd */
+ PORT_IRQ_DMAS_FIS = BIT(2), /* DMA Setup FIS rx'd */
+ PORT_IRQ_PIOS_FIS = BIT(1), /* PIO Setup FIS rx'd */
+ PORT_IRQ_D2H_REG_FIS = BIT(0), /* D2H Register FIS rx'd */
PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR |
PORT_IRQ_IF_ERR |
@@ -161,27 +162,27 @@ enum {
PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS,
/* PORT_CMD bits */
- PORT_CMD_ASP = (1 << 27), /* Aggressive Slumber/Partial */
- PORT_CMD_ALPE = (1 << 26), /* Aggressive Link PM enable */
- PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
- PORT_CMD_FBSCP = (1 << 22), /* FBS Capable Port */
- PORT_CMD_ESP = (1 << 21), /* External Sata Port */
- PORT_CMD_CPD = (1 << 20), /* Cold Presence Detection */
- PORT_CMD_MPSP = (1 << 19), /* Mechanical Presence Switch */
- PORT_CMD_HPCP = (1 << 18), /* HotPlug Capable Port */
- PORT_CMD_PMP = (1 << 17), /* PMP attached */
- PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
- PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */
- PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */
- PORT_CMD_CLO = (1 << 3), /* Command list override */
- PORT_CMD_POWER_ON = (1 << 2), /* Power up device */
- PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
- PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
-
- PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */
- PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */
- PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
- PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
+ PORT_CMD_ASP = BIT(27), /* Aggressive Slumber/Partial */
+ PORT_CMD_ALPE = BIT(26), /* Aggressive Link PM enable */
+ PORT_CMD_ATAPI = BIT(24), /* Device is ATAPI */
+ PORT_CMD_FBSCP = BIT(22), /* FBS Capable Port */
+ PORT_CMD_ESP = BIT(21), /* External Sata Port */
+ PORT_CMD_CPD = BIT(20), /* Cold Presence Detection */
+ PORT_CMD_MPSP = BIT(19), /* Mechanical Presence Switch */
+ PORT_CMD_HPCP = BIT(18), /* HotPlug Capable Port */
+ PORT_CMD_PMP = BIT(17), /* PMP attached */
+ PORT_CMD_LIST_ON = BIT(15), /* cmd list DMA engine running */
+ PORT_CMD_FIS_ON = BIT(14), /* FIS DMA engine running */
+ PORT_CMD_FIS_RX = BIT(4), /* Enable FIS receive DMA engine */
+ PORT_CMD_CLO = BIT(3), /* Command list override */
+ PORT_CMD_POWER_ON = BIT(2), /* Power up device */
+ PORT_CMD_SPIN_UP = BIT(1), /* Spin up device */
+ PORT_CMD_START = BIT(0), /* Enable port DMA engine */
+
+ PORT_CMD_ICC_MASK = (0xfu << 28), /* i/f ICC state mask */
+ PORT_CMD_ICC_ACTIVE = (0x1u << 28), /* Put i/f in active state */
+ PORT_CMD_ICC_PARTIAL = (0x2u << 28), /* Put i/f in partial state */
+ PORT_CMD_ICC_SLUMBER = (0x6u << 28), /* Put i/f in slumber state */
/* PORT_CMD capabilities mask */
PORT_CMD_CAP = PORT_CMD_HPCP | PORT_CMD_MPSP |
@@ -192,9 +193,9 @@ enum {
PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */
PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */
PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */
- PORT_FBS_SDE = (1 << 2), /* FBS single device error */
- PORT_FBS_DEC = (1 << 1), /* FBS device error clear */
- PORT_FBS_EN = (1 << 0), /* Enable FBS */
+ PORT_FBS_SDE = BIT(2), /* FBS single device error */
+ PORT_FBS_DEC = BIT(1), /* FBS device error clear */
+ PORT_FBS_EN = BIT(0), /* Enable FBS */
/* PORT_DEVSLP bits */
PORT_DEVSLP_DM_OFFSET = 25, /* DITO multiplier offset */
@@ -202,50 +203,50 @@ enum {
PORT_DEVSLP_DITO_OFFSET = 15, /* DITO offset */
PORT_DEVSLP_MDAT_OFFSET = 10, /* Minimum assertion time */
PORT_DEVSLP_DETO_OFFSET = 2, /* DevSlp exit timeout */
- PORT_DEVSLP_DSP = (1 << 1), /* DevSlp present */
- PORT_DEVSLP_ADSE = (1 << 0), /* Aggressive DevSlp enable */
+ PORT_DEVSLP_DSP = BIT(1), /* DevSlp present */
+ PORT_DEVSLP_ADSE = BIT(0), /* Aggressive DevSlp enable */
/* hpriv->flags bits */
#define AHCI_HFLAGS(flags) .private_data = (void *)(flags)
- AHCI_HFLAG_NO_NCQ = (1 << 0),
- AHCI_HFLAG_IGN_IRQ_IF_ERR = (1 << 1), /* ignore IRQ_IF_ERR */
- AHCI_HFLAG_IGN_SERR_INTERNAL = (1 << 2), /* ignore SERR_INTERNAL */
- AHCI_HFLAG_32BIT_ONLY = (1 << 3), /* force 32bit */
- AHCI_HFLAG_MV_PATA = (1 << 4), /* PATA port */
- AHCI_HFLAG_NO_MSI = (1 << 5), /* no PCI MSI */
- AHCI_HFLAG_NO_PMP = (1 << 6), /* no PMP */
- AHCI_HFLAG_SECT255 = (1 << 8), /* max 255 sectors */
- AHCI_HFLAG_YES_NCQ = (1 << 9), /* force NCQ cap on */
- AHCI_HFLAG_NO_SUSPEND = (1 << 10), /* don't suspend */
- AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = (1 << 11), /* treat SRST timeout as
- link offline */
- AHCI_HFLAG_NO_SNTF = (1 << 12), /* no sntf */
- AHCI_HFLAG_NO_FPDMA_AA = (1 << 13), /* no FPDMA AA */
- AHCI_HFLAG_YES_FBS = (1 << 14), /* force FBS cap on */
- AHCI_HFLAG_DELAY_ENGINE = (1 << 15), /* do not start engine on
- port start (wait until
- error-handling stage) */
- AHCI_HFLAG_NO_DEVSLP = (1 << 17), /* no device sleep */
- AHCI_HFLAG_NO_FBS = (1 << 18), /* no FBS */
+ AHCI_HFLAG_NO_NCQ = BIT(0),
+ AHCI_HFLAG_IGN_IRQ_IF_ERR = BIT(1), /* ignore IRQ_IF_ERR */
+ AHCI_HFLAG_IGN_SERR_INTERNAL = BIT(2), /* ignore SERR_INTERNAL */
+ AHCI_HFLAG_32BIT_ONLY = BIT(3), /* force 32bit */
+ AHCI_HFLAG_MV_PATA = BIT(4), /* PATA port */
+ AHCI_HFLAG_NO_MSI = BIT(5), /* no PCI MSI */
+ AHCI_HFLAG_NO_PMP = BIT(6), /* no PMP */
+ AHCI_HFLAG_SECT255 = BIT(8), /* max 255 sectors */
+ AHCI_HFLAG_YES_NCQ = BIT(9), /* force NCQ cap on */
+ AHCI_HFLAG_NO_SUSPEND = BIT(10), /* don't suspend */
+ AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = BIT(11), /* treat SRST timeout as
+ link offline */
+ AHCI_HFLAG_NO_SNTF = BIT(12), /* no sntf */
+ AHCI_HFLAG_NO_FPDMA_AA = BIT(13), /* no FPDMA AA */
+ AHCI_HFLAG_YES_FBS = BIT(14), /* force FBS cap on */
+ AHCI_HFLAG_DELAY_ENGINE = BIT(15), /* do not start engine on
+ port start (wait until
+ error-handling stage) */
+ AHCI_HFLAG_NO_DEVSLP = BIT(17), /* no device sleep */
+ AHCI_HFLAG_NO_FBS = BIT(18), /* no FBS */
#ifdef CONFIG_PCI_MSI
- AHCI_HFLAG_MULTI_MSI = (1 << 20), /* per-port MSI(-X) */
+ AHCI_HFLAG_MULTI_MSI = BIT(20), /* per-port MSI(-X) */
#else
/* compile out MSI infrastructure */
AHCI_HFLAG_MULTI_MSI = 0,
#endif
- AHCI_HFLAG_WAKE_BEFORE_STOP = (1 << 22), /* wake before DMA stop */
- AHCI_HFLAG_YES_ALPM = (1 << 23), /* force ALPM cap on */
- AHCI_HFLAG_NO_WRITE_TO_RO = (1 << 24), /* don't write to read
- only registers */
- AHCI_HFLAG_USE_LPM_POLICY = (1 << 25), /* chipset that should use
- SATA_MOBILE_LPM_POLICY
- as default lpm_policy */
- AHCI_HFLAG_SUSPEND_PHYS = (1 << 26), /* handle PHYs during
- suspend/resume */
- AHCI_HFLAG_NO_SXS = (1 << 28), /* SXS not supported */
+ AHCI_HFLAG_WAKE_BEFORE_STOP = BIT(22), /* wake before DMA stop */
+ AHCI_HFLAG_YES_ALPM = BIT(23), /* force ALPM cap on */
+ AHCI_HFLAG_NO_WRITE_TO_RO = BIT(24), /* don't write to read
+ only registers */
+ AHCI_HFLAG_USE_LPM_POLICY = BIT(25), /* chipset that should use
+ SATA_MOBILE_LPM_POLICY
+ as default lpm_policy */
+ AHCI_HFLAG_SUSPEND_PHYS = BIT(26), /* handle PHYs during
+ suspend/resume */
+ AHCI_HFLAG_NO_SXS = BIT(28), /* SXS not supported */
/* ap->flags bits */
@@ -261,22 +262,22 @@ enum {
EM_MAX_RETRY = 5,
/* em_ctl bits */
- EM_CTL_RST = (1 << 9), /* Reset */
- EM_CTL_TM = (1 << 8), /* Transmit Message */
- EM_CTL_MR = (1 << 0), /* Message Received */
- EM_CTL_ALHD = (1 << 26), /* Activity LED */
- EM_CTL_XMT = (1 << 25), /* Transmit Only */
- EM_CTL_SMB = (1 << 24), /* Single Message Buffer */
- EM_CTL_SGPIO = (1 << 19), /* SGPIO messages supported */
- EM_CTL_SES = (1 << 18), /* SES-2 messages supported */
- EM_CTL_SAFTE = (1 << 17), /* SAF-TE messages supported */
- EM_CTL_LED = (1 << 16), /* LED messages supported */
+ EM_CTL_RST = BIT(9), /* Reset */
+ EM_CTL_TM = BIT(8), /* Transmit Message */
+ EM_CTL_MR = BIT(0), /* Message Received */
+ EM_CTL_ALHD = BIT(26), /* Activity LED */
+ EM_CTL_XMT = BIT(25), /* Transmit Only */
+ EM_CTL_SMB = BIT(24), /* Single Message Buffer */
+ EM_CTL_SGPIO = BIT(19), /* SGPIO messages supported */
+ EM_CTL_SES = BIT(18), /* SES-2 messages supported */
+ EM_CTL_SAFTE = BIT(17), /* SAF-TE messages supported */
+ EM_CTL_LED = BIT(16), /* LED messages supported */
/* em message type */
- EM_MSG_TYPE_LED = (1 << 0), /* LED */
- EM_MSG_TYPE_SAFTE = (1 << 1), /* SAF-TE */
- EM_MSG_TYPE_SES2 = (1 << 2), /* SES-2 */
- EM_MSG_TYPE_SGPIO = (1 << 3), /* SGPIO */
+ EM_MSG_TYPE_LED = BIT(0), /* LED */
+ EM_MSG_TYPE_SAFTE = BIT(1), /* SAF-TE */
+ EM_MSG_TYPE_SES2 = BIT(2), /* SES-2 */
+ EM_MSG_TYPE_SGPIO = BIT(3), /* SGPIO */
};
struct ahci_cmd_hdr {
