On 12/3/22 19:54, Arnd Bergmann wrote: > From: Arnd Bergmann <arnd@xxxxxxxx> > > gcc-13 slightly changes the type of constant expressions that are defined > in an enum, which triggers a compile time sanity check in libata: > > linux/drivers/ata/libahci.c: In function 'ahci_led_store': > linux/include/linux/compiler_types.h:357:45: error: call to '__compiletime_assert_302' declared with attribute error: BUILD_BUG_ON failed: sizeof(_s) > sizeof(long) > 357 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__) > > The new behavior is that sizeof() returns the same value for the > constant as it does for the enum type, which is generally more sensible > and consistent. > > The problem in libata is that it contains a single enum definition for > lots of unrelated constants, some of which are large positive (unsigned) > integers like 0xffffffff, while others like (1<<31) are interpreted as > negative integers, and this forces the enum type to become 64 bit wide > even though most constants would still fit into a signed 32-bit 'int'. > > Fix this by changing the entire enum definition to use BIT(x) in place > of (1<<x), which results in all values being seen as 'unsigned' and > fitting into an unsigned 32-bit type. > > Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107917 > Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405 > Reported-by: Luis Machado <luis.machado@xxxxxxx> > Cc: linux-ide@xxxxxxxxxxxxxxx > Cc: Damien Le Moal <damien.lemoal@xxxxxxxxxxxxxxxxxx> > Cc: stable@xxxxxxxxxxxxxxx > Cc: Randy Dunlap <rdunlap@xxxxxxxxxxxxx> > Signed-off-by: Arnd Bergmann <arnd@xxxxxxxx> Looks all good to me. One nit: for the PORT_CMD_ICC_XXX definitions, we could use GENMASK() to be consistant with the use of BIT(), no ? Not a big deal though. > --- > Luis, I don't have gcc-13 installed on the machine I used for > creating this patch, can you give this a spin and see if it > addresses the build failure? Luis, if you test/review, please send Tested-by/Reviewed-by tags ! > > v2 changes: > - fix typos in changelog > - change PORT_CMD_ICC_* constants as well > - include linux/bits.h > --- > drivers/ata/ahci.h | 245 +++++++++++++++++++++++---------------------- > 1 file changed, 123 insertions(+), 122 deletions(-) > > diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h > index 7add8e79912b..ff8e6ae1c636 100644 > --- a/drivers/ata/ahci.h > +++ b/drivers/ata/ahci.h > @@ -24,6 +24,7 @@ > #include <linux/libata.h> > #include <linux/phy/phy.h> > #include <linux/regulator/consumer.h> > +#include <linux/bits.h> > > /* Enclosure Management Control */ > #define EM_CTRL_MSG_TYPE 0x000f0000 > @@ -53,12 +54,12 @@ enum { > AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ + > AHCI_CMD_TBL_AR_SZ + > (AHCI_RX_FIS_SZ * 16), > - AHCI_IRQ_ON_SG = (1 << 31), > - AHCI_CMD_ATAPI = (1 << 5), > - AHCI_CMD_WRITE = (1 << 6), > - AHCI_CMD_PREFETCH = (1 << 7), > - AHCI_CMD_RESET = (1 << 8), > - AHCI_CMD_CLR_BUSY = (1 << 10), > + AHCI_IRQ_ON_SG = BIT(31), > + AHCI_CMD_ATAPI = BIT(5), > + AHCI_CMD_WRITE = BIT(6), > + AHCI_CMD_PREFETCH = BIT(7), > + AHCI_CMD_RESET = BIT(8), > + AHCI_CMD_CLR_BUSY = BIT(10), > > RX_FIS_PIO_SETUP = 0x20, /* offset of PIO Setup FIS data */ > RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */ > @@ -76,37 +77,37 @@ enum { > HOST_CAP2 = 0x24, /* host capabilities, extended */ > > /* HOST_CTL bits */ > - HOST_RESET = (1 << 0), /* reset controller; self-clear */ > - HOST_IRQ_EN = (1 << 1), /* global IRQ enable */ > - HOST_MRSM = (1 << 2), /* MSI Revert to Single Message */ > - HOST_AHCI_EN = (1 << 31), /* AHCI enabled */ > + HOST_RESET = BIT(0), /* reset controller; self-clear */ > + HOST_IRQ_EN = BIT(1), /* global IRQ enable */ > + HOST_MRSM = BIT(2), /* MSI Revert to Single Message */ > + HOST_AHCI_EN = BIT(31), /* AHCI enabled */ > > /* HOST_CAP bits */ > - HOST_CAP_SXS = (1 << 5), /* Supports External SATA */ > - HOST_CAP_EMS = (1 << 6), /* Enclosure Management support */ > - HOST_CAP_CCC = (1 << 7), /* Command Completion Coalescing */ > - HOST_CAP_PART = (1 << 13), /* Partial state capable */ > - HOST_CAP_SSC = (1 << 14), /* Slumber state capable */ > - HOST_CAP_PIO_MULTI = (1 << 15), /* PIO multiple DRQ support */ > - HOST_CAP_FBS = (1 << 16), /* FIS-based switching support */ > - HOST_CAP_PMP = (1 << 17), /* Port Multiplier support */ > - HOST_CAP_ONLY = (1 << 18), /* Supports AHCI mode only */ > - HOST_CAP_CLO = (1 << 24), /* Command List Override support */ > - HOST_CAP_LED = (1 << 25), /* Supports activity LED */ > - HOST_CAP_ALPM = (1 << 26), /* Aggressive Link PM support */ > - HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */ > - HOST_CAP_MPS = (1 << 28), /* Mechanical presence switch */ > - HOST_CAP_SNTF = (1 << 29), /* SNotification register */ > - HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */ > - HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */ > + HOST_CAP_SXS = BIT(5), /* Supports External SATA */ > + HOST_CAP_EMS = BIT(6), /* Enclosure Management support */ > + HOST_CAP_CCC = BIT(7), /* Command Completion Coalescing */ > + HOST_CAP_PART = BIT(13), /* Partial state capable */ > + HOST_CAP_SSC = BIT(14), /* Slumber state capable */ > + HOST_CAP_PIO_MULTI = BIT(15), /* PIO multiple DRQ support */ > + HOST_CAP_FBS = BIT(16), /* FIS-based switching support */ > + HOST_CAP_PMP = BIT(17), /* Port Multiplier support */ > + HOST_CAP_ONLY = BIT(18), /* Supports AHCI mode only */ > + HOST_CAP_CLO = BIT(24), /* Command List Override support */ > + HOST_CAP_LED = BIT(25), /* Supports activity LED */ > + HOST_CAP_ALPM = BIT(26), /* Aggressive Link PM support */ > + HOST_CAP_SSS = BIT(27), /* Staggered Spin-up */ > + HOST_CAP_MPS = BIT(28), /* Mechanical presence switch */ > + HOST_CAP_SNTF = BIT(29), /* SNotification register */ > + HOST_CAP_NCQ = BIT(30), /* Native Command Queueing */ > + HOST_CAP_64 = BIT(31), /* PCI DAC (64-bit DMA) support */ > > /* HOST_CAP2 bits */ > - HOST_CAP2_BOH = (1 << 0), /* BIOS/OS handoff supported */ > - HOST_CAP2_NVMHCI = (1 << 1), /* NVMHCI supported */ > - HOST_CAP2_APST = (1 << 2), /* Automatic partial to slumber */ > - HOST_CAP2_SDS = (1 << 3), /* Support device sleep */ > - HOST_CAP2_SADM = (1 << 4), /* Support aggressive DevSlp */ > - HOST_CAP2_DESO = (1 << 5), /* DevSlp from slumber only */ > + HOST_CAP2_BOH = BIT(0), /* BIOS/OS handoff supported */ > + HOST_CAP2_NVMHCI = BIT(1), /* NVMHCI supported */ > + HOST_CAP2_APST = BIT(2), /* Automatic partial to slumber */ > + HOST_CAP2_SDS = BIT(3), /* Support device sleep */ > + HOST_CAP2_SADM = BIT(4), /* Support aggressive DevSlp */ > + HOST_CAP2_DESO = BIT(5), /* DevSlp from slumber only */ > > /* registers for each SATA port */ > PORT_LST_ADDR = 0x00, /* command list DMA addr */ > @@ -128,24 +129,24 @@ enum { > PORT_DEVSLP = 0x44, /* device sleep */ > > /* PORT_IRQ_{STAT,MASK} bits */ > - PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */ > - PORT_IRQ_TF_ERR = (1 << 30), /* task file error */ > - PORT_IRQ_HBUS_ERR = (1 << 29), /* host bus fatal error */ > - PORT_IRQ_HBUS_DATA_ERR = (1 << 28), /* host bus data error */ > - PORT_IRQ_IF_ERR = (1 << 27), /* interface fatal error */ > - PORT_IRQ_IF_NONFATAL = (1 << 26), /* interface non-fatal error */ > - PORT_IRQ_OVERFLOW = (1 << 24), /* xfer exhausted available S/G */ > - PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */ > - > - PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */ > - PORT_IRQ_DMPS = (1 << 7), /* mechanical presence status */ > - PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */ > - PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */ > - PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */ > - PORT_IRQ_SDB_FIS = (1 << 3), /* Set Device Bits FIS rx'd */ > - PORT_IRQ_DMAS_FIS = (1 << 2), /* DMA Setup FIS rx'd */ > - PORT_IRQ_PIOS_FIS = (1 << 1), /* PIO Setup FIS rx'd */ > - PORT_IRQ_D2H_REG_FIS = (1 << 0), /* D2H Register FIS rx'd */ > + PORT_IRQ_COLD_PRES = BIT(31), /* cold presence detect */ > + PORT_IRQ_TF_ERR = BIT(30), /* task file error */ > + PORT_IRQ_HBUS_ERR = BIT(29), /* host bus fatal error */ > + PORT_IRQ_HBUS_DATA_ERR = BIT(28), /* host bus data error */ > + PORT_IRQ_IF_ERR = BIT(27), /* interface fatal error */ > + PORT_IRQ_IF_NONFATAL = BIT(26), /* interface non-fatal error */ > + PORT_IRQ_OVERFLOW = BIT(24), /* xfer exhausted available S/G */ > + PORT_IRQ_BAD_PMP = BIT(23), /* incorrect port multiplier */ > + > + PORT_IRQ_PHYRDY = BIT(22), /* PhyRdy changed */ > + PORT_IRQ_DMPS = BIT(7), /* mechanical presence status */ > + PORT_IRQ_CONNECT = BIT(6), /* port connect change status */ > + PORT_IRQ_SG_DONE = BIT(5), /* descriptor processed */ > + PORT_IRQ_UNK_FIS = BIT(4), /* unknown FIS rx'd */ > + PORT_IRQ_SDB_FIS = BIT(3), /* Set Device Bits FIS rx'd */ > + PORT_IRQ_DMAS_FIS = BIT(2), /* DMA Setup FIS rx'd */ > + PORT_IRQ_PIOS_FIS = BIT(1), /* PIO Setup FIS rx'd */ > + PORT_IRQ_D2H_REG_FIS = BIT(0), /* D2H Register FIS rx'd */ > > PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR | > PORT_IRQ_IF_ERR | > @@ -161,27 +162,27 @@ enum { > PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS, > > /* PORT_CMD bits */ > - PORT_CMD_ASP = (1 << 27), /* Aggressive Slumber/Partial */ > - PORT_CMD_ALPE = (1 << 26), /* Aggressive Link PM enable */ > - PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */ > - PORT_CMD_FBSCP = (1 << 22), /* FBS Capable Port */ > - PORT_CMD_ESP = (1 << 21), /* External Sata Port */ > - PORT_CMD_CPD = (1 << 20), /* Cold Presence Detection */ > - PORT_CMD_MPSP = (1 << 19), /* Mechanical Presence Switch */ > - PORT_CMD_HPCP = (1 << 18), /* HotPlug Capable Port */ > - PORT_CMD_PMP = (1 << 17), /* PMP attached */ > - PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */ > - PORT_CMD_FIS_ON = (1 << 14), /* FIS DMA engine running */ > - PORT_CMD_FIS_RX = (1 << 4), /* Enable FIS receive DMA engine */ > - PORT_CMD_CLO = (1 << 3), /* Command list override */ > - PORT_CMD_POWER_ON = (1 << 2), /* Power up device */ > - PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */ > - PORT_CMD_START = (1 << 0), /* Enable port DMA engine */ > - > - PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */ > - PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */ > - PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */ > - PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */ > + PORT_CMD_ASP = BIT(27), /* Aggressive Slumber/Partial */ > + PORT_CMD_ALPE = BIT(26), /* Aggressive Link PM enable */ > + PORT_CMD_ATAPI = BIT(24), /* Device is ATAPI */ > + PORT_CMD_FBSCP = BIT(22), /* FBS Capable Port */ > + PORT_CMD_ESP = BIT(21), /* External Sata Port */ > + PORT_CMD_CPD = BIT(20), /* Cold Presence Detection */ > + PORT_CMD_MPSP = BIT(19), /* Mechanical Presence Switch */ > + PORT_CMD_HPCP = BIT(18), /* HotPlug Capable Port */ > + PORT_CMD_PMP = BIT(17), /* PMP attached */ > + PORT_CMD_LIST_ON = BIT(15), /* cmd list DMA engine running */ > + PORT_CMD_FIS_ON = BIT(14), /* FIS DMA engine running */ > + PORT_CMD_FIS_RX = BIT(4), /* Enable FIS receive DMA engine */ > + PORT_CMD_CLO = BIT(3), /* Command list override */ > + PORT_CMD_POWER_ON = BIT(2), /* Power up device */ > + PORT_CMD_SPIN_UP = BIT(1), /* Spin up device */ > + PORT_CMD_START = BIT(0), /* Enable port DMA engine */ > + > + PORT_CMD_ICC_MASK = (0xfu << 28), /* i/f ICC state mask */ > + PORT_CMD_ICC_ACTIVE = (0x1u << 28), /* Put i/f in active state */ > + PORT_CMD_ICC_PARTIAL = (0x2u << 28), /* Put i/f in partial state */ > + PORT_CMD_ICC_SLUMBER = (0x6u << 28), /* Put i/f in slumber state */ > > /* PORT_CMD capabilities mask */ > PORT_CMD_CAP = PORT_CMD_HPCP | PORT_CMD_MPSP | > @@ -192,9 +193,9 @@ enum { > PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */ > PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */ > PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */ > - PORT_FBS_SDE = (1 << 2), /* FBS single device error */ > - PORT_FBS_DEC = (1 << 1), /* FBS device error clear */ > - PORT_FBS_EN = (1 << 0), /* Enable FBS */ > + PORT_FBS_SDE = BIT(2), /* FBS single device error */ > + PORT_FBS_DEC = BIT(1), /* FBS device error clear */ > + PORT_FBS_EN = BIT(0), /* Enable FBS */ > > /* PORT_DEVSLP bits */ > PORT_DEVSLP_DM_OFFSET = 25, /* DITO multiplier offset */ > @@ -202,50 +203,50 @@ enum { > PORT_DEVSLP_DITO_OFFSET = 15, /* DITO offset */ > PORT_DEVSLP_MDAT_OFFSET = 10, /* Minimum assertion time */ > PORT_DEVSLP_DETO_OFFSET = 2, /* DevSlp exit timeout */ > - PORT_DEVSLP_DSP = (1 << 1), /* DevSlp present */ > - PORT_DEVSLP_ADSE = (1 << 0), /* Aggressive DevSlp enable */ > + PORT_DEVSLP_DSP = BIT(1), /* DevSlp present */ > + PORT_DEVSLP_ADSE = BIT(0), /* Aggressive DevSlp enable */ > > /* hpriv->flags bits */ > > #define AHCI_HFLAGS(flags) .private_data = (void *)(flags) > > - AHCI_HFLAG_NO_NCQ = (1 << 0), > - AHCI_HFLAG_IGN_IRQ_IF_ERR = (1 << 1), /* ignore IRQ_IF_ERR */ > - AHCI_HFLAG_IGN_SERR_INTERNAL = (1 << 2), /* ignore SERR_INTERNAL */ > - AHCI_HFLAG_32BIT_ONLY = (1 << 3), /* force 32bit */ > - AHCI_HFLAG_MV_PATA = (1 << 4), /* PATA port */ > - AHCI_HFLAG_NO_MSI = (1 << 5), /* no PCI MSI */ > - AHCI_HFLAG_NO_PMP = (1 << 6), /* no PMP */ > - AHCI_HFLAG_SECT255 = (1 << 8), /* max 255 sectors */ > - AHCI_HFLAG_YES_NCQ = (1 << 9), /* force NCQ cap on */ > - AHCI_HFLAG_NO_SUSPEND = (1 << 10), /* don't suspend */ > - AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = (1 << 11), /* treat SRST timeout as > - link offline */ > - AHCI_HFLAG_NO_SNTF = (1 << 12), /* no sntf */ > - AHCI_HFLAG_NO_FPDMA_AA = (1 << 13), /* no FPDMA AA */ > - AHCI_HFLAG_YES_FBS = (1 << 14), /* force FBS cap on */ > - AHCI_HFLAG_DELAY_ENGINE = (1 << 15), /* do not start engine on > - port start (wait until > - error-handling stage) */ > - AHCI_HFLAG_NO_DEVSLP = (1 << 17), /* no device sleep */ > - AHCI_HFLAG_NO_FBS = (1 << 18), /* no FBS */ > + AHCI_HFLAG_NO_NCQ = BIT(0), > + AHCI_HFLAG_IGN_IRQ_IF_ERR = BIT(1), /* ignore IRQ_IF_ERR */ > + AHCI_HFLAG_IGN_SERR_INTERNAL = BIT(2), /* ignore SERR_INTERNAL */ > + AHCI_HFLAG_32BIT_ONLY = BIT(3), /* force 32bit */ > + AHCI_HFLAG_MV_PATA = BIT(4), /* PATA port */ > + AHCI_HFLAG_NO_MSI = BIT(5), /* no PCI MSI */ > + AHCI_HFLAG_NO_PMP = BIT(6), /* no PMP */ > + AHCI_HFLAG_SECT255 = BIT(8), /* max 255 sectors */ > + AHCI_HFLAG_YES_NCQ = BIT(9), /* force NCQ cap on */ > + AHCI_HFLAG_NO_SUSPEND = BIT(10), /* don't suspend */ > + AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = BIT(11), /* treat SRST timeout as > + link offline */ > + AHCI_HFLAG_NO_SNTF = BIT(12), /* no sntf */ > + AHCI_HFLAG_NO_FPDMA_AA = BIT(13), /* no FPDMA AA */ > + AHCI_HFLAG_YES_FBS = BIT(14), /* force FBS cap on */ > + AHCI_HFLAG_DELAY_ENGINE = BIT(15), /* do not start engine on > + port start (wait until > + error-handling stage) */ > + AHCI_HFLAG_NO_DEVSLP = BIT(17), /* no device sleep */ > + AHCI_HFLAG_NO_FBS = BIT(18), /* no FBS */ > > #ifdef CONFIG_PCI_MSI > - AHCI_HFLAG_MULTI_MSI = (1 << 20), /* per-port MSI(-X) */ > + AHCI_HFLAG_MULTI_MSI = BIT(20), /* per-port MSI(-X) */ > #else > /* compile out MSI infrastructure */ > AHCI_HFLAG_MULTI_MSI = 0, > #endif > - AHCI_HFLAG_WAKE_BEFORE_STOP = (1 << 22), /* wake before DMA stop */ > - AHCI_HFLAG_YES_ALPM = (1 << 23), /* force ALPM cap on */ > - AHCI_HFLAG_NO_WRITE_TO_RO = (1 << 24), /* don't write to read > - only registers */ > - AHCI_HFLAG_USE_LPM_POLICY = (1 << 25), /* chipset that should use > - SATA_MOBILE_LPM_POLICY > - as default lpm_policy */ > - AHCI_HFLAG_SUSPEND_PHYS = (1 << 26), /* handle PHYs during > - suspend/resume */ > - AHCI_HFLAG_NO_SXS = (1 << 28), /* SXS not supported */ > + AHCI_HFLAG_WAKE_BEFORE_STOP = BIT(22), /* wake before DMA stop */ > + AHCI_HFLAG_YES_ALPM = BIT(23), /* force ALPM cap on */ > + AHCI_HFLAG_NO_WRITE_TO_RO = BIT(24), /* don't write to read > + only registers */ > + AHCI_HFLAG_USE_LPM_POLICY = BIT(25), /* chipset that should use > + SATA_MOBILE_LPM_POLICY > + as default lpm_policy */ > + AHCI_HFLAG_SUSPEND_PHYS = BIT(26), /* handle PHYs during > + suspend/resume */ > + AHCI_HFLAG_NO_SXS = BIT(28), /* SXS not supported */ > > /* ap->flags bits */ > > @@ -261,22 +262,22 @@ enum { > EM_MAX_RETRY = 5, > > /* em_ctl bits */ > - EM_CTL_RST = (1 << 9), /* Reset */ > - EM_CTL_TM = (1 << 8), /* Transmit Message */ > - EM_CTL_MR = (1 << 0), /* Message Received */ > - EM_CTL_ALHD = (1 << 26), /* Activity LED */ > - EM_CTL_XMT = (1 << 25), /* Transmit Only */ > - EM_CTL_SMB = (1 << 24), /* Single Message Buffer */ > - EM_CTL_SGPIO = (1 << 19), /* SGPIO messages supported */ > - EM_CTL_SES = (1 << 18), /* SES-2 messages supported */ > - EM_CTL_SAFTE = (1 << 17), /* SAF-TE messages supported */ > - EM_CTL_LED = (1 << 16), /* LED messages supported */ > + EM_CTL_RST = BIT(9), /* Reset */ > + EM_CTL_TM = BIT(8), /* Transmit Message */ > + EM_CTL_MR = BIT(0), /* Message Received */ > + EM_CTL_ALHD = BIT(26), /* Activity LED */ > + EM_CTL_XMT = BIT(25), /* Transmit Only */ > + EM_CTL_SMB = BIT(24), /* Single Message Buffer */ > + EM_CTL_SGPIO = BIT(19), /* SGPIO messages supported */ > + EM_CTL_SES = BIT(18), /* SES-2 messages supported */ > + EM_CTL_SAFTE = BIT(17), /* SAF-TE messages supported */ > + EM_CTL_LED = BIT(16), /* LED messages supported */ > > /* em message type */ > - EM_MSG_TYPE_LED = (1 << 0), /* LED */ > - EM_MSG_TYPE_SAFTE = (1 << 1), /* SAF-TE */ > - EM_MSG_TYPE_SES2 = (1 << 2), /* SES-2 */ > - EM_MSG_TYPE_SGPIO = (1 << 3), /* SGPIO */ > + EM_MSG_TYPE_LED = BIT(0), /* LED */ > + EM_MSG_TYPE_SAFTE = BIT(1), /* SAF-TE */ > + EM_MSG_TYPE_SES2 = BIT(2), /* SES-2 */ > + EM_MSG_TYPE_SGPIO = BIT(3), /* SGPIO */ > }; > > struct ahci_cmd_hdr { -- Damien Le Moal Western Digital Research
