Re: [PATCH v4 09/13] ARM: dts: sun8i: r40: add sata node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Aug 31, 2018 at 03:58:34PM +0800, Chen-Yu Tsai wrote:
> On Fri, Aug 31, 2018 at 3:56 PM Corentin Labbe
> <clabbe.montjoie@xxxxxxxxx> wrote:
> >
> > On Fri, Aug 31, 2018 at 09:35:00AM +0200, Maxime Ripard wrote:
> > > On Thu, Aug 30, 2018 at 09:01:16PM +0200, Corentin Labbe wrote:
> > > > R40 have a sata controller which is the same as A20.
> > > > This patch adds a DT node for it.
> > > >
> > > > Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
> > > > Signed-off-by: Corentin Labbe <clabbe.montjoie@xxxxxxxxx>
> > > > ---
> > > >  arch/arm/boot/dts/sun8i-r40.dtsi | 23 +++++++++++++++++++++++
> > > >  1 file changed, 23 insertions(+)
> > > >
> > > > diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
> > > > index 852c2ccc3268..d6b5820da850 100644
> > > > --- a/arch/arm/boot/dts/sun8i-r40.dtsi
> > > > +++ b/arch/arm/boot/dts/sun8i-r40.dtsi
> > > > @@ -550,6 +550,29 @@
> > > >                     #size-cells = <0>;
> > > >             };
> > > >
> > > > +           ahci: sata@1c18000 {
> > > > +                   compatible = "allwinner,sun8i-r40-ahci";
> > > > +                   reg = <0x01c18000 0x1000>;
> > > > +                   interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
> > > > +                   clocks = <&ccu CLK_BUS_SATA>, <&ccu CLK_SATA>;
> > > > +                   resets = <&ccu RST_BUS_SATA>;
> > > > +                   resets-name = "ahci";
> > > > +                   #address-cells = <1>;
> > > > +                   #size-cells = <0>;
> > > > +                   status = "disabled";
> > > > +
> > > > +                   sata_port: sata-port@0 {
> > > > +                           reg = <0>;
> > > > +                           phys = <&sata_phy>;
> > > > +                   };
> > > > +           };
> > > > +
> > > > +           sata_phy: sata-phy@1c180c0  {
> > > > +                   compatible = "allwinner,sun8i-r40-sata-phy";
> > > > +                   reg = <0x1c180c0 0x200>;
> > >
> > > Overlapping devices in the DTS is not ok.
> > >
> >
> > I do the same than arch/arm/boot/dts/berlin2.dtsi (sata@e90000 phy@e900a0)
> > But since it is not a good justification, it seems that regmap is my only solution ?
> 
> Since you are effectively splitting one device node into two, you should
> adjust the original (ahci) device nodes register range.
> 

I cannot do that if I remove patch 13, iow If I keep phy init code in both place as you requested.



[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux