On 11/22/2017 06:02 AM, sonofagun@xxxxxxxxxxxxxxx wrote: > Hello, you have a brand new AMD box and an old seagate HDD. That does NOT sound good... I am an AMD fan as well. Many years ago my brother and I bought our first AMD board with SB700. A good chip that had many annoying errata... A SATA II chip paired with the best iGPU of its era. Only a good HDD was suitable for such a board! That was an HDD from the seagate 7200.10 family. A family full of innovations. The first SATA II family, the first PMR HDD family and the first family offering 5 year warranty. Those disks are very reliable compared to 7200.7 and to 7200.11!!! Actually their access time is like 7200RPM disks while the 7200.11 had access times of 5400RPM class disks... Unfortunately those disks had a compatibility issue with the AMD AHCI implementation. All revisions of the SB7x0 southbridge family were affected and transfer speed was hurt badly when NCQ was enabled! I wrote about it(https://ata.wiki.kernel.org/index.php/Known_issues#SATA_hard_drives_which_show_poor_performance_with_sequential_reads_.28e.g._hdparm_-t.29) so that everyone will know it. > At that time there was no official firmware for any SATA disk. Firmware was given only when something was really wrong such as the deathstars. That attitude applied to all HDD manufacturers. My brother had to phone seagate at their headquarters in order to ask for a fix. Our next seagate disks(7200.11) were all having the same transfer speed issues with NCQ. They were too arrogant to admit the issue and very reluctant to release new firmware. We were informed that there will be no fix even though the 7200.11 family was just released. We were forced to RMA 4x 320GB and 4x 500GB of them at once and switch to the legendary WD RE3(all those still work flawlessly from 2008!). This was just prior seagate admitted the rest firmware issues of this family... After that mess, new firmware has been released gradually for most seagate HDD families! > > As you can guess I am not surprised that you have an issue with such a disk on an AMD board. Compared to current disks it is very power hungry and not suitable for your board. What is worse, you are using an out of warranty HDD here. > > Your SATA II HDD is attached on a SATA 3.x AMD chip. This HDD cannot even reach SATA I speeds(average well below 100MB/s). If your disk operates in 1.5 Gbps you will not have noticeable performance degradation. You will just lose maximum burst speed. Some time ago I saw this: "https://marc.info/?t=150843788300002&r=1&w=2";, but I have not fallen on it as I have never used SATA hotplug. You have not mentioned hotplug here but it might be related as the libata EH is invoked! > > I still have a 320GB 7200.10 ST3320620AS with 3.AAK firmware and will try to measure it with SATA I speed on my AMD KABINI box. We were given a newer firmware for this one while the seagate firmware finder site says it has no firmware! The new firmware is 3.AAM for this GALAXY HDD but the speed problem on AMD AHCI was not completely resolved but it made a difference so we have kept this HDD. We had a couple 320GB too, with 3.AAE firmware but seagate supplied no new firmware so they were RMAed. > > As I said above, those disks have had speed issues with NCQ. Let's start from that. Please boot with NCQ disabled and see if it helps... > libata.force=noncq option seems to prevent the messages from occurring. 5 kernel builds (j16) with none. > Since your HDD is old, please run: > sudo smartctl /dev/sd@ -x #smartctl /dev/sda -x smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.14.1-lcrs] (SUSE RPM) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3160815AS Serial Number: 6RX0JL7T Firmware Version: 3.AAD User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Wed Nov 22 10:33:35 2017 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 54) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 084 006 - 71870712 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1811 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 090 060 030 - 945790650 9 Power_On_Hours -O--CK 014 014 000 - 75675 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1805 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 067 060 045 - 33 (Min/Max 33/34) 194 Temperature_Celsius -O---K 033 040 000 - 33 (0 21 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 083 061 000 - 207077472 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 133 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 9725 - # 2 Extended offline Interrupted (host reset) 60% 9723 - # 3 Extended offline Completed without error 00% 8889 - # 4 Extended offline Completed without error 00% 8361 - # 5 Extended offline Completed without error 00% 7765 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS > sudo hdparm -I /dev/sd@ # hdparm -I /dev/sda /dev/sda: ATA device, with non-removable media Model Number: ST3160815AS Serial Number: 6RX0JL7T Firmware Revision: 3.AAD Standards: Supported: 7 6 5 4 Likely used: 7 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 312581808 Logical Sector size: 512 bytes Physical Sector size: 512 bytes device size with M = 1024*1024: 152627 MBytes device size with M = 1000*1000: 160041 MBytes (160 GB) cache/buffer size = 8192 KBytes Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Recommended acoustic management value: 208, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * DOWNLOAD_MICROCODE SET_MAX security extension * 48-bit Address feature set Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * Gen1 signaling speed (1.5Gb/s) * Native Command Queueing (NCQ) * Phy event counters Device-initiated interface power management * Software settings preservation Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count not supported: enhanced erase Checksum: correct > sudo hdparm --Istdout /dev/sd@ hdparm --Istdout /dev/sda /dev/sda: 0c5a 3fff c837 0010 0000 0000 003f 0000 0000 0000 2020 2020 2020 2020 2020 2020 3652 5830 4a4c 3754 0000 4000 0004 332e 4141 4420 2020 5354 3331 3630 3831 3541 5320 2020 2020 2020 2020 2020 2020 2020 2020 2020 2020 2020 2020 2020 2020 8010 0000 2f00 4000 0200 0200 0007 3fff 0010 003f fc10 00fb 0110 ffff 0fff 0000 0007 0003 0078 0078 0078 0078 0000 0000 0000 0000 0000 0000 001f 0502 0000 0048 0040 00fe 0000 346b 7d01 4023 3469 3401 4023 407f 0000 0000 fefe fffe 0000 d000 0000 0000 0000 0000 0000 9eb0 12a1 0000 0000 0000 0000 4000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0100 0000 0002 0000 0000 0000 0000 0000 0000 0000 0000 0009 9eb0 12a1 9eb0 12a1 2020 0002 02b6 0002 008a 3c06 3c0a 0000 07c6 0100 0800 1314 1200 0002 0080 0000 0000 00a0 0202 0000 0404 0000 0000 0000 0000 1b00 000b 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 5ca5 > dmesg # dmesg [ 0.000000] Linux version 4.14.1-lcrs (root@harley) (gcc version 4.8.5 (SUSE Linux)) #1 SMP PREEMPT Tue Nov 21 14:06:01 EST 2017 [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-4.14.1-lcrs root=/dev/disk/by-id/ata-ST3160815AS_6RX0JL7T-part5 video=1600x1200 noresume splash=verbose showopts audit=0 apm=0ff vmalloc=256M libata.force=noncq [ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'compacted' format. [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009bbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009bc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000009d7ffff] usable [ 0.000000] BIOS-e820: [mem 0x0000000009d80000-0x0000000009ffffff] reserved [ 0.000000] BIOS-e820: [mem 0x000000000a000000-0x00000000c72cffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000c72d0000-0x00000000c733bfff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000c733c000-0x00000000cd2e6fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000cd2e7000-0x00000000cd3d7fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000cd3d8000-0x00000000cd4c1fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000cd4c2000-0x00000000cd894fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000cd895000-0x00000000ce3e8fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ce3e9000-0x00000000ceffffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000cf000000-0x00000000cfffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fdf00000-0x00000000fdffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fea00000-0x00000000fea0ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000feb80000-0x00000000fec01fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec30000-0x00000000fec30fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fedc2000-0x00000000fedcffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fedd4000-0x00000000fedd5fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000feefffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000042f37ffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] random: fast init done [ 0.000000] SMBIOS 3.0 present. [ 0.000000] DMI: Micro-Star International Co., Ltd. MS-7A34/B350 TOMAHAWK ARCTIC (MS-7A34), BIOS H.70 09/20/2017 [ 0.000000] tsc: Fast TSC calibration failed [ 0.000000] tsc: Using PIT calibration value [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] e820: last_pfn = 0x42f380 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF write-through [ 0.000000] C0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back [ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back [ 0.000000] 2 base 0000C0000000 mask FFFFF0000000 write-back [ 0.000000] 3 base 0000CF000000 mask FFFFFF000000 uncachable [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] TOM2: 0000000430000000 aka 17152M [ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.000000] e820: update [mem 0xcf000000-0xffffffff] usable ==> reserved [ 0.000000] e820: last_pfn = 0xcf000 max_arch_pfn = 0x400000000 [ 0.000000] Base memory trampoline at [ffff880000095000] 95000 size 24576 [ 0.000000] Using GB pages for direct mapping [ 0.000000] BRK [0x0110a000, 0x0110afff] PGTABLE [ 0.000000] BRK [0x0110b000, 0x0110bfff] PGTABLE [ 0.000000] BRK [0x0110c000, 0x0110cfff] PGTABLE [ 0.000000] BRK [0x0110d000, 0x0110dfff] PGTABLE [ 0.000000] BRK [0x0110e000, 0x0110efff] PGTABLE [ 0.000000] BRK [0x0110f000, 0x0110ffff] PGTABLE [ 0.000000] RAMDISK: [mem 0x36ef3000-0x37770fff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000F05B0 000024 (v02 ALASKA) [ 0.000000] ACPI: XSDT 0x00000000CD4C2090 00009C (v01 ALASKA A M I 01072009 AMI 00010013) [ 0.000000] ACPI: FACP 0x00000000CD4C7FA0 000114 (v06 ALASKA A M I 01072009 AMI 00010013) [ 0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has valid Length but zero Address: 0x0000000000000000/0x1 (20170728/tbfadt-658) [ 0.000000] ACPI: DSDT 0x00000000CD4C21C0 005DDA (v02 ALASKA A M I 01072009 INTL 20120913) [ 0.000000] ACPI: FACS 0x00000000CD87EE00 000040 [ 0.000000] ACPI: APIC 0x00000000CD4C80B8 0000DE (v03 ALASKA A M I 01072009 AMI 00010013) [ 0.000000] ACPI: FPDT 0x00000000CD4C8198 000044 (v01 ALASKA A M I 01072009 AMI 00010013) [ 0.000000] ACPI: FIDT 0x00000000CD4C81E0 00009C (v01 ALASKA A M I 01072009 AMI 00010013) [ 0.000000] ACPI: SSDT 0x00000000CD4C8280 008C4C (v02 AMD AMD ALIB 00000002 MSFT 04000000) [ 0.000000] ACPI: CRAT 0x00000000CD4D0ED0 000F50 (v01 AMD AMD CRAT 00000001 AMD 00000001) [ 0.000000] ACPI: CDIT 0x00000000CD4D1E20 000029 (v01 AMD AMD CDIT 00000001 AMD 00000001) [ 0.000000] ACPI: SSDT 0x00000000CD4D1E50 0017B7 (v01 AMD AMD AOD 00000001 INTL 20120913) [ 0.000000] ACPI: MCFG 0x00000000CD4D3608 00003C (v01 ALASKA A M I 01072009 MSFT 00010013) [ 0.000000] ACPI: HPET 0x00000000CD4D3648 000038 (v01 ALASKA A M I 01072009 AMI 00000005) [ 0.000000] ACPI: SSDT 0x00000000CD4D3680 000024 (v01 AMDFCH FCHZP 00001000 INTL 20120913) [ 0.000000] ACPI: UEFI 0x00000000CD4D36A8 000042 (v01 00000000 00000000) [ 0.000000] ACPI: IVRS 0x00000000CD4D36F0 0000D0 (v02 AMD AMD IVRS 00000001 AMD 00000000) [ 0.000000] ACPI: SSDT 0x00000000CD4D37C0 0000F8 (v01 AMD AMD PT 00001000 INTL 20120913) [ 0.000000] ACPI: SSDT 0x00000000CD4D38B8 001664 (v01 AMD CPMCMN 00000001 INTL 20120913) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000042f37ffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009afff] [ 0.000000] node 0: [mem 0x0000000000100000-0x0000000009d7ffff] [ 0.000000] node 0: [mem 0x000000000a000000-0x00000000c72cffff] [ 0.000000] node 0: [mem 0x00000000c733c000-0x00000000cd2e6fff] [ 0.000000] node 0: [mem 0x00000000cd3d8000-0x00000000cd4c1fff] [ 0.000000] node 0: [mem 0x00000000ce3e9000-0x00000000ceffffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000042f37ffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000042f37ffff] [ 0.000000] On node 0 totalpages: 4182038 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 3605 pages reserved [ 0.000000] DMA zone: 3994 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 13108 pages used for memmap [ 0.000000] DMA32 zone: 838908 pages, LIFO batch:31 [ 0.000000] Normal zone: 52174 pages used for memmap [ 0.000000] Normal zone: 3339136 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1]) [ 0.000000] IOAPIC[0]: apic_id 17, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] IOAPIC[1]: apic_id 18, version 33, address 0xfec01000, GSI 24-55 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x10228201 base: 0xfed00000 [ 0.000000] smpboot: Allowing 16 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009b000-0x0009bfff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009c000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0x09d80000-0x09ffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xc72d0000-0xc733bfff] [ 0.000000] PM: Registered nosave memory: [mem 0xcd2e7000-0xcd3d7fff] [ 0.000000] PM: Registered nosave memory: [mem 0xcd4c2000-0xcd894fff] [ 0.000000] PM: Registered nosave memory: [mem 0xcd895000-0xce3e8fff] [ 0.000000] PM: Registered nosave memory: [mem 0xcf000000-0xcfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xf7ffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfdefffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfdf00000-0xfdffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfe000000-0xfe9fffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfea00000-0xfea0ffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfea10000-0xfeb7ffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfeb80000-0xfec01fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfec02000-0xfec0ffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfec11000-0xfec2ffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfec30000-0xfec30fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfec31000-0xfecfffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed3ffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed45000-0xfed7ffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed90000-0xfedc1fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfedc2000-0xfedcffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfedd0000-0xfedd3fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfedd4000-0xfedd5fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfedd6000-0xfedfffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfeefffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfef00000-0xfeffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff] [ 0.000000] e820: [mem 0xd0000000-0xf7ffffff] available for PCI devices [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:16 nr_node_ids:1 [ 0.000000] percpu: Embedded 37 pages/cpu @ffff88042ec00000 s113560 r8192 d29800 u262144 [ 0.000000] pcpu-alloc: s113560 r8192 d29800 u262144 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 [0] 08 09 10 11 12 13 14 15 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 4113087 [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-4.14.1-lcrs root=/dev/disk/by-id/ata-ST3160815AS_6RX0JL7T-part5 video=1600x1200 noresume splash=verbose showopts audit=0 apm=0ff vmalloc=256M libata.force=noncq [ 0.000000] audit: disabled (until reboot) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Memory: 16348820K/16728152K available (7057K kernel code, 994K rwdata, 2972K rodata, 1072K init, 948K bss, 379332K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32 [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=16. [ 0.000000] RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16 [ 0.000000] NR_IRQS: 8448, nr_irqs: 1096, preallocated irqs: 16 [ 0.000000] Offload RCU callbacks from CPUs: . [ 0.000000] spurious 8259A interrupt: IRQ7. [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns [ 0.000000] hpet clockevent registered [ 0.000000] tsc: Fast TSC calibration failed [ 0.002000] tsc: PIT calibration matches HPET. 1 loops [ 0.002000] tsc: Detected 2999.744 MHz processor [ 0.002000] Calibrating delay loop (skipped), value calculated using timer frequency.. 5999.48 BogoMIPS (lpj=2999744) [ 0.002000] pid_max: default: 32768 minimum: 301 [ 0.002000] ACPI: Core revision 20170728 [ 0.013769] ACPI: 6 ACPI AML tables successfully acquired and loaded [ 0.013794] Security Framework initialized [ 0.013850] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.013882] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.014039] CPU: Physical Processor ID: 0 [ 0.014041] CPU: Processor Core ID: 0 [ 0.014049] mce: CPU supports 23 MCE banks [ 0.014067] LVT offset 1 assigned for vector 0xf9 [ 0.014195] LVT offset 2 assigned for vector 0xf4 [ 0.014208] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 512 [ 0.014209] Last level dTLB entries: 4KB 1536, 2MB 1536, 4MB 768, 1GB 0 [ 0.014272] Freeing SMP alternatives memory: 28K [ 0.015051] smpboot: Max logical packages: 2 [ 0.015055] Switched APIC routing to physical flat. [ 0.016297] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.027000] smpboot: CPU0: AMD Ryzen 7 1700 Eight-Core Processor (family: 0x17, model: 0x1, stepping: 0x1) [ 0.030006] Performance Events: Fam17h core perfctr, AMD PMU driver. [ 0.030011] ... version: 0 [ 0.030012] ... bit width: 48 [ 0.030013] ... generic registers: 6 [ 0.030015] ... value mask: 0000ffffffffffff [ 0.030016] ... max period: 00007fffffffffff [ 0.030017] ... fixed-purpose events: 0 [ 0.030019] ... event mask: 000000000000003f [ 0.032001] Hierarchical SRCU implementation. [ 0.038001] smp: Bringing up secondary CPUs ... [ 0.046008] x86: Booting SMP configuration: [ 0.046011] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 #12 #13 #14 #15 [ 0.173053] smp: Brought up 1 node, 16 CPUs [ 0.173061] smpboot: Total of 16 processors activated (95991.80 BogoMIPS) [ 0.174474] devtmpfs: initialized [ 0.175029] PM: Registering ACPI NVS region [mem 0xcd4c2000-0xcd894fff] (4009984 bytes) [ 0.175128] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.175133] futex hash table entries: 4096 (order: 6, 262144 bytes) [ 0.175225] pinctrl core: initialized pinctrl subsystem [ 0.175284] RTC time: 14:59:56, date: 11/22/17 [ 0.175368] NET: Registered protocol family 16 [ 0.176006] cpuidle: using governor ladder [ 0.176011] cpuidle: using governor menu [ 0.176038] ACPI: bus type PCI registered [ 0.176038] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.176068] PCI: Using configuration type 1 for base access [ 0.176070] PCI: Using configuration type 1 for extended access [ 0.176264] mtrr: your CPUs had inconsistent variable MTRR settings [ 0.176266] mtrr: probably your BIOS does not setup all CPUs. [ 0.176267] mtrr: corrected configuration. [ 0.178027] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.178030] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.181059] ACPI: Added _OSI(Module Device) [ 0.181062] ACPI: Added _OSI(Processor Device) [ 0.181063] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.181065] ACPI: Added _OSI(Processor Aggregator Device) [ 0.181213] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored [ 0.181233] ACPI: Executed 2 blocks of module-level executable AML code [ 0.189405] ACPI: Interpreter enabled [ 0.189422] ACPI: (supports S0 S3 S4 S5) [ 0.189423] ACPI: Using IOAPIC for interrupt routing [ 0.189568] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.189862] ACPI: Enabled 2 GPEs in block 00 to 1F [ 0.197860] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.197866] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI] [ 0.198106] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability] [ 0.198457] PCI host bridge to bus 0000:00 [ 0.198461] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window] [ 0.198463] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window] [ 0.198465] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window] [ 0.198467] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.198470] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.198472] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window] [ 0.198475] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfec2ffff window] [ 0.198477] pci_bus 0000:00: root bus resource [mem 0xfee00000-0xffffffff window] [ 0.198480] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.198487] pci 0000:00:00.0: [1022:1450] type 00 class 0x060000 [ 0.198569] pci 0000:00:00.2: [1022:1451] type 00 class 0x080600 [ 0.198665] pci 0000:00:01.0: [1022:1452] type 00 class 0x060000 [ 0.198739] pci 0000:00:01.3: [1022:1453] type 01 class 0x060400 [ 0.198782] pci 0000:00:01.3: PME# supported from D0 D3hot D3cold [ 0.198845] pci 0000:00:02.0: [1022:1452] type 00 class 0x060000 [ 0.198929] pci 0000:00:03.0: [1022:1452] type 00 class 0x060000 [ 0.199002] pci 0000:00:03.1: [1022:1453] type 01 class 0x060400 [ 0.199062] pci 0000:00:03.1: PME# supported from D0 D3hot D3cold [ 0.199131] pci 0000:00:04.0: [1022:1452] type 00 class 0x060000 [ 0.199221] pci 0000:00:07.0: [1022:1452] type 00 class 0x060000 [ 0.199289] pci 0000:00:07.1: [1022:1454] type 01 class 0x060400 [ 0.199312] pci 0000:00:07.1: enabling Extended Tags [ 0.199332] pci 0000:00:07.1: PME# supported from D0 D3hot D3cold [ 0.199400] pci 0000:00:08.0: [1022:1452] type 00 class 0x060000 [ 0.199470] pci 0000:00:08.1: [1022:1454] type 01 class 0x060400 [ 0.199494] pci 0000:00:08.1: enabling Extended Tags [ 0.199515] pci 0000:00:08.1: PME# supported from D0 D3hot D3cold [ 0.199616] pci 0000:00:14.0: [1022:790b] type 00 class 0x0c0500 [ 0.199832] pci 0000:00:14.3: [1022:790e] type 00 class 0x060100 [ 0.200054] pci 0000:00:18.0: [1022:1460] type 00 class 0x060000 [ 0.200112] pci 0000:00:18.1: [1022:1461] type 00 class 0x060000 [ 0.200170] pci 0000:00:18.2: [1022:1462] type 00 class 0x060000 [ 0.200227] pci 0000:00:18.3: [1022:1463] type 00 class 0x060000 [ 0.200285] pci 0000:00:18.4: [1022:1464] type 00 class 0x060000 [ 0.200343] pci 0000:00:18.5: [1022:1465] type 00 class 0x060000 [ 0.200403] pci 0000:00:18.6: [1022:1466] type 00 class 0x060000 [ 0.200460] pci 0000:00:18.7: [1022:1467] type 00 class 0x060000 [ 0.200574] pci 0000:03:00.0: [1022:43bb] type 00 class 0x0c0330 [ 0.200604] pci 0000:03:00.0: reg 0x10: [mem 0xf6fa0000-0xf6fa7fff 64bit] [ 0.200667] pci 0000:03:00.0: PME# supported from D3hot D3cold [ 0.200703] pci 0000:03:00.1: [1022:43b7] type 00 class 0x010601 [ 0.200758] pci 0000:03:00.1: reg 0x24: [mem 0xf6f80000-0xf6f9ffff] [ 0.200765] pci 0000:03:00.1: reg 0x30: [mem 0xf6f00000-0xf6f7ffff pref] [ 0.200798] pci 0000:03:00.1: PME# supported from D3hot D3cold [ 0.200832] pci 0000:03:00.2: [1022:43b2] type 01 class 0x060400 [ 0.200909] pci 0000:03:00.2: PME# supported from D3hot D3cold [ 0.203009] pci 0000:00:01.3: PCI bridge to [bus 03-2b] [ 0.203014] pci 0000:00:01.3: bridge window [io 0x9000-0xefff] [ 0.203015] pci 0000:00:01.3: bridge window [mem 0xf3800000-0xf6ffffff] [ 0.203018] pci 0000:00:01.3: bridge window [mem 0xe0000000-0xe5ffffff 64bit pref] [ 0.203070] pci 0000:04:00.0: [1022:43b4] type 01 class 0x060400 [ 0.203154] pci 0000:04:00.0: PME# supported from D3hot D3cold [ 0.203193] pci 0000:04:01.0: [1022:43b4] type 01 class 0x060400 [ 0.203276] pci 0000:04:01.0: PME# supported from D3hot D3cold [ 0.203317] pci 0000:04:04.0: [1022:43b4] type 01 class 0x060400 [ 0.203401] pci 0000:04:04.0: PME# supported from D3hot D3cold [ 0.203439] pci 0000:04:06.0: [1022:43b4] type 01 class 0x060400 [ 0.203522] pci 0000:04:06.0: PME# supported from D3hot D3cold [ 0.203559] pci 0000:04:07.0: [1022:43b4] type 01 class 0x060400 [ 0.203642] pci 0000:04:07.0: PME# supported from D3hot D3cold [ 0.203692] pci 0000:03:00.2: PCI bridge to [bus 04-2b] [ 0.203698] pci 0000:03:00.2: bridge window [io 0x9000-0xefff] [ 0.203701] pci 0000:03:00.2: bridge window [mem 0xf3800000-0xf6efffff] [ 0.203705] pci 0000:03:00.2: bridge window [mem 0xe0000000-0xe5ffffff 64bit pref] [ 0.203755] pci 0000:1f:00.0: [1b21:1080] type 01 class 0x060400 [ 0.203947] pci 0000:1f:00.0: supports D1 D2 [ 0.203948] pci 0000:1f:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.207011] pci 0000:04:00.0: PCI bridge to [bus 1f-20] [ 0.207017] pci 0000:04:00.0: bridge window [io 0xe000-0xefff] [ 0.207020] pci 0000:04:00.0: bridge window [mem 0xf6e00000-0xf6efffff] [ 0.207094] pci 0000:20:00.0: [9004:3860] type 00 class 0x010000 [ 0.207133] pci 0000:20:00.0: reg 0x10: [io 0xe000-0xe0ff] [ 0.207150] pci 0000:20:00.0: reg 0x14: [mem 0xf6e11000-0xf6e11fff] [ 0.207232] pci 0000:20:00.0: reg 0x30: [mem 0xf6e00000-0xf6e0ffff pref] [ 0.207315] pci 0000:20:01.0: [1090:4610] type 00 class 0xff0000 [ 0.207348] pci 0000:20:01.0: reg 0x10: [io 0xe100-0xe13f] [ 0.207365] pci 0000:20:01.0: reg 0x14: [mem 0xf6e10000-0xf6e10fff] [ 0.207551] pci 0000:1f:00.0: PCI bridge to [bus 20] [ 0.207562] pci 0000:1f:00.0: bridge window [io 0xe000-0xefff] [ 0.207567] pci 0000:1f:00.0: bridge window [mem 0xf6e00000-0xf6efffff] [ 0.207634] pci 0000:21:00.0: [10ec:8168] type 00 class 0x020000 [ 0.207691] pci 0000:21:00.0: reg 0x10: [io 0xd000-0xd0ff] [ 0.207726] pci 0000:21:00.0: reg 0x18: [mem 0xf6d04000-0xf6d04fff 64bit] [ 0.207747] pci 0000:21:00.0: reg 0x20: [mem 0xf6d00000-0xf6d03fff 64bit] [ 0.207840] pci 0000:21:00.0: supports D1 D2 [ 0.207841] pci 0000:21:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.210014] pci 0000:04:01.0: PCI bridge to [bus 21] [ 0.210020] pci 0000:04:01.0: bridge window [io 0xd000-0xdfff] [ 0.210022] pci 0000:04:01.0: bridge window [mem 0xf6d00000-0xf6dfffff] [ 0.210079] pci 0000:22:00.0: [104c:8231] type 01 class 0x060400 [ 0.210269] pci 0000:22:00.0: supports D1 D2 [ 0.210297] pci 0000:22:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.210308] pci 0000:04:04.0: PCI bridge to [bus 22-25] [ 0.210314] pci 0000:04:04.0: bridge window [io 0x9000-0xafff] [ 0.210316] pci 0000:04:04.0: bridge window [mem 0xf3800000-0xf5dfffff] [ 0.210320] pci 0000:04:04.0: bridge window [mem 0xe0000000-0xe3ffffff 64bit pref] [ 0.210404] pci 0000:23:04.0: [12d8:8150] type 01 class 0x060400 [ 0.210633] pci 0000:22:00.0: PCI bridge to [bus 23-25] [ 0.210644] pci 0000:22:00.0: bridge window [io 0x9000-0xafff] [ 0.210649] pci 0000:22:00.0: bridge window [mem 0xf3800000-0xf5dfffff] [ 0.210658] pci 0000:22:00.0: bridge window [mem 0xe0000000-0xe3ffffff 64bit pref] [ 0.210736] pci 0000:24:04.0: [10b5:0480] type 00 class 0x0e8000 [ 0.210791] pci 0000:24:04.0: reg 0x10: [mem 0xf5d18000-0xf5d183ff] [ 0.210813] pci 0000:24:04.0: reg 0x14: [mem 0xf5000000-0xf57fffff] [ 0.210834] pci 0000:24:04.0: reg 0x18: [mem 0xf5d17000-0xf5d1700f] [ 0.211066] pci 0000:24:05.0: [10b5:0480] type 00 class 0x0e8000 [ 0.211120] pci 0000:24:05.0: reg 0x10: [mem 0xf5d16000-0xf5d163ff] [ 0.211142] pci 0000:24:05.0: reg 0x14: [mem 0xf4800000-0xf4ffffff] [ 0.211163] pci 0000:24:05.0: reg 0x18: [mem 0xf5d15000-0xf5d1500f] [ 0.211395] pci 0000:24:06.0: [10b5:0480] type 00 class 0x0e8000 [ 0.211449] pci 0000:24:06.0: reg 0x10: [mem 0xf5d14000-0xf5d143ff] [ 0.211471] pci 0000:24:06.0: reg 0x14: [mem 0xf4000000-0xf47fffff] [ 0.211493] pci 0000:24:06.0: reg 0x18: [mem 0xf5d13000-0xf5d1300f] [ 0.211723] pci 0000:24:07.0: [10b5:0480] type 00 class 0x0e8000 [ 0.211777] pci 0000:24:07.0: reg 0x10: [mem 0xf5d12000-0xf5d123ff] [ 0.211799] pci 0000:24:07.0: reg 0x14: [mem 0xf3800000-0xf3ffffff] [ 0.211820] pci 0000:24:07.0: reg 0x18: [mem 0xf5d11000-0xf5d1100f] [ 0.212053] pci 0000:24:08.0: [3388:0022] type 01 class 0x060400 [ 0.212248] pci 0000:24:08.0: supports D1 D2 [ 0.212249] pci 0000:24:08.0: PME# supported from D0 D1 D2 D3hot [ 0.212295] pci 0000:24:09.0: [114f:0027] type 00 class 0x078000 [ 0.212338] pci 0000:24:09.0: reg 0x10: [mem 0xf5800000-0xf5bfffff] [ 0.212465] pci 0000:24:09.0: reg 0x30: [mem 0xf5d00000-0xf5d0ffff pref] [ 0.212518] pci 0000:24:0a.0: [1090:4360] type 00 class 0x058000 [ 0.212561] pci 0000:24:0a.0: reg 0x10: [mem 0xf5d10000-0xf5d100ff] [ 0.212583] pci 0000:24:0a.0: reg 0x14: [io 0xa000-0xa0ff] [ 0.212605] pci 0000:24:0a.0: reg 0x18: [mem 0xe0000000-0xe3ffffff pref] [ 0.212689] pci 0000:24:0a.0: reg 0x30: [mem 0xf5d19000-0xf5d197ff pref] [ 0.212792] pci 0000:23:04.0: PCI bridge to [bus 24-25] [ 0.212804] pci 0000:23:04.0: bridge window [io 0x9000-0xafff] [ 0.212809] pci 0000:23:04.0: bridge window [mem 0xf3800000-0xf5dfffff] [ 0.212819] pci 0000:23:04.0: bridge window [mem 0xe0000000-0xe3ffffff 64bit pref] [ 0.212893] pci 0000:25:00.0: [1090:0100] type 00 class 0xff0000 [ 0.212941] pci 0000:25:00.0: reg 0x10: [mem 0xf5c0a000-0xf5c0afff] [ 0.212966] pci 0000:25:00.0: reg 0x14: [mem 0xf5c08000-0xf5c09fff] [ 0.212990] pci 0000:25:00.0: reg 0x18: [mem 0xf5c00000-0xf5c07fff] [ 0.213235] pci 0000:24:08.0: PCI bridge to [bus 25] [ 0.213249] pci 0000:24:08.0: bridge window [io 0x9000-0x9fff] [ 0.213256] pci 0000:24:08.0: bridge window [mem 0xf5c00000-0xf5cfffff] [ 0.213349] pci 0000:26:00.0: [1b4b:9215] type 00 class 0x010601 [ 0.213392] pci 0000:26:00.0: reg 0x10: [io 0xc050-0xc057] [ 0.213402] pci 0000:26:00.0: reg 0x14: [io 0xc040-0xc043] [ 0.213413] pci 0000:26:00.0: reg 0x18: [io 0xc030-0xc037] [ 0.213423] pci 0000:26:00.0: reg 0x1c: [io 0xc020-0xc023] [ 0.213434] pci 0000:26:00.0: reg 0x20: [io 0xc000-0xc01f] [ 0.213444] pci 0000:26:00.0: reg 0x24: [mem 0xf6c10000-0xf6c107ff] [ 0.213455] pci 0000:26:00.0: reg 0x30: [mem 0xf6c00000-0xf6c0ffff pref] [ 0.213513] pci 0000:26:00.0: PME# supported from D3hot [ 0.216011] pci 0000:04:06.0: PCI bridge to [bus 26] [ 0.216016] pci 0000:04:06.0: bridge window [io 0xc000-0xcfff] [ 0.216019] pci 0000:04:06.0: bridge window [mem 0xf6c00000-0xf6cfffff] [ 0.216074] pci 0000:27:00.0: [104c:8231] type 01 class 0x060400 [ 0.216262] pci 0000:27:00.0: supports D1 D2 [ 0.216290] pci 0000:27:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.216301] pci 0000:04:07.0: PCI bridge to [bus 27-2b] [ 0.216307] pci 0000:04:07.0: bridge window [io 0xb000-0xbfff] [ 0.216309] pci 0000:04:07.0: bridge window [mem 0xf6000000-0xf6afffff] [ 0.216313] pci 0000:04:07.0: bridge window [mem 0xe4000000-0xe5ffffff 64bit pref] [ 0.216397] pci 0000:28:04.0: [12d8:8150] type 01 class 0x060400 [ 0.216626] pci 0000:27:00.0: PCI bridge to [bus 28-2b] [ 0.216637] pci 0000:27:00.0: bridge window [io 0xb000-0xbfff] [ 0.216642] pci 0000:27:00.0: bridge window [mem 0xf6000000-0xf6afffff] [ 0.216651] pci 0000:27:00.0: bridge window [mem 0xe4000000-0xe5ffffff 64bit pref] [ 0.216723] pci 0000:29:04.0: [10b7:9200] type 00 class 0x020000 [ 0.216771] pci 0000:29:04.0: reg 0x10: [io 0xb100-0xb17f] [ 0.216793] pci 0000:29:04.0: reg 0x14: [mem 0xf6a34000-0xf6a3407f] [ 0.216898] pci 0000:29:04.0: reg 0x30: [mem 0xf6a00000-0xf6a1ffff pref] [ 0.216963] pci 0000:29:04.0: supports D1 D2 [ 0.216963] pci 0000:29:04.0: PME# supported from D0 D1 D2 D3hot [ 0.217016] pci 0000:29:05.0: [3388:0022] type 01 class 0x060400 [ 0.217211] pci 0000:29:05.0: supports D1 D2 [ 0.217212] pci 0000:29:05.0: PME# supported from D0 D1 D2 D3hot [ 0.217270] pci 0000:29:06.0: [3388:0022] type 01 class 0x060400 [ 0.217465] pci 0000:29:06.0: supports D1 D2 [ 0.217466] pci 0000:29:06.0: PME# supported from D0 D1 D2 D3hot [ 0.217524] pci 0000:29:07.0: [10b5:0480] type 00 class 0x0e8000 [ 0.217578] pci 0000:29:07.0: reg 0x10: [mem 0xf6a33000-0xf6a333ff] [ 0.217599] pci 0000:29:07.0: reg 0x14: [mem 0xf6000000-0xf67fffff] [ 0.217622] pci 0000:29:07.0: reg 0x18: [mem 0xf6a32000-0xf6a3200f] [ 0.217845] pci 0000:29:08.0: [9004:3860] type 00 class 0x010000 [ 0.217893] pci 0000:29:08.0: reg 0x10: [io 0xb000-0xb0ff] [ 0.217915] pci 0000:29:08.0: reg 0x14: [mem 0xf6a31000-0xf6a31fff] [ 0.218022] pci 0000:29:08.0: reg 0x30: [mem 0xf6a20000-0xf6a2ffff pref] [ 0.218120] pci 0000:29:0a.0: [13c0:0080] type 00 class 0x078000 [ 0.218163] pci 0000:29:0a.0: reg 0x10: [mem 0xf6a30000-0xf6a300ff] [ 0.218390] pci 0000:28:04.0: PCI bridge to [bus 29-2b] [ 0.218402] pci 0000:28:04.0: bridge window [io 0xb000-0xbfff] [ 0.218407] pci 0000:28:04.0: bridge window [mem 0xf6000000-0xf6afffff] [ 0.218418] pci 0000:28:04.0: bridge window [mem 0xe4000000-0xe5ffffff 64bit pref] [ 0.218498] pci 0000:2a:00.0: [1090:4710] type 00 class 0xff0000 [ 0.218552] pci 0000:2a:00.0: reg 0x10: [mem 0xf6900000-0xf69001ff] [ 0.218577] pci 0000:2a:00.0: reg 0x14: [mem 0xe5000000-0xe5ffffff pref] [ 0.218885] pci 0000:29:05.0: PCI bridge to [bus 2a] [ 0.218905] pci 0000:29:05.0: bridge window [mem 0xf6900000-0xf69fffff] [ 0.218917] pci 0000:29:05.0: bridge window [mem 0xe5000000-0xe5ffffff 64bit pref] [ 0.219001] pci 0000:2b:00.0: [1090:4710] type 00 class 0xff0000 [ 0.219055] pci 0000:2b:00.0: reg 0x10: [mem 0xf6800000-0xf68001ff] [ 0.219080] pci 0000:2b:00.0: reg 0x14: [mem 0xe4000000-0xe4ffffff pref] [ 0.219389] pci 0000:29:06.0: PCI bridge to [bus 2b] [ 0.219409] pci 0000:29:06.0: bridge window [mem 0xf6800000-0xf68fffff] [ 0.219421] pci 0000:29:06.0: bridge window [mem 0xe4000000-0xe4ffffff 64bit pref] [ 0.219539] pci 0000:2c:00.0: [10de:0092] type 00 class 0x030000 [ 0.219568] pci 0000:2c:00.0: reg 0x10: [mem 0xf2000000-0xf2ffffff] [ 0.219580] pci 0000:2c:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.219591] pci 0000:2c:00.0: reg 0x1c: [mem 0xf1000000-0xf1ffffff 64bit] [ 0.219598] pci 0000:2c:00.0: reg 0x24: [io 0xf000-0xf07f] [ 0.219605] pci 0000:2c:00.0: reg 0x30: [mem 0xf3000000-0xf301ffff pref] [ 0.219663] pci 0000:2c:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.219671] pci 0000:00:03.1: PCI bridge to [bus 2c] [ 0.219675] pci 0000:00:03.1: bridge window [io 0xf000-0xffff] [ 0.219677] pci 0000:00:03.1: bridge window [mem 0xf1000000-0xf30fffff] [ 0.219680] pci 0000:00:03.1: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.219718] pci 0000:2d:00.0: [1022:145a] type 00 class 0x130000 [ 0.219752] pci 0000:2d:00.0: enabling Extended Tags [ 0.219794] pci 0000:2d:00.2: [1022:1456] type 00 class 0x108000 [ 0.219815] pci 0000:2d:00.2: reg 0x18: [mem 0xf7100000-0xf71fffff] [ 0.219825] pci 0000:2d:00.2: reg 0x24: [mem 0xf7200000-0xf7201fff] [ 0.219831] pci 0000:2d:00.2: enabling Extended Tags [ 0.219882] pci 0000:2d:00.3: [1022:145c] type 00 class 0x0c0330 [ 0.219898] pci 0000:2d:00.3: reg 0x10: [mem 0xf7000000-0xf70fffff 64bit] [ 0.219916] pci 0000:2d:00.3: enabling Extended Tags [ 0.219939] pci 0000:2d:00.3: PME# supported from D0 D3hot D3cold [ 0.219976] pci 0000:00:07.1: PCI bridge to [bus 2d] [ 0.219981] pci 0000:00:07.1: bridge window [mem 0xf7000000-0xf72fffff] [ 0.220030] pci 0000:2e:00.0: [1022:1455] type 00 class 0x130000 [ 0.220067] pci 0000:2e:00.0: enabling Extended Tags [ 0.220112] pci 0000:2e:00.2: [1022:7901] type 00 class 0x010601 [ 0.220144] pci 0000:2e:00.2: reg 0x24: [mem 0xf7308000-0xf7308fff] [ 0.220151] pci 0000:2e:00.2: enabling Extended Tags [ 0.220176] pci 0000:2e:00.2: PME# supported from D3hot D3cold [ 0.220208] pci 0000:2e:00.3: [1022:1457] type 00 class 0x040300 [ 0.220223] pci 0000:2e:00.3: reg 0x10: [mem 0xf7300000-0xf7307fff] [ 0.220246] pci 0000:2e:00.3: enabling Extended Tags [ 0.220270] pci 0000:2e:00.3: PME# supported from D0 D3hot D3cold [ 0.220311] pci 0000:00:08.1: PCI bridge to [bus 2e] [ 0.220315] pci 0000:00:08.1: bridge window [mem 0xf7300000-0xf73fffff] [ 0.220332] pci_bus 0000:00: on NUMA node 0 [ 0.220740] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 11 14 15) *0 [ 0.220802] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 11 14 15) *0 [ 0.220855] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 10 11 14 15) *0 [ 0.220921] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 11 14 15) *0 [ 0.220980] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0 [ 0.221030] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0 [ 0.221079] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0 [ 0.221128] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0 [ 0.221589] pci 0000:2c:00.0: vgaarb: setting as boot VGA device [ 0.221592] pci 0000:2c:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.221595] pci 0000:2c:00.0: vgaarb: bridge control possible [ 0.221597] vgaarb: loaded [ 0.221641] SCSI subsystem initialized [ 0.222008] libata version 3.00 loaded. [ 0.222010] ACPI: bus type USB registered [ 0.222020] usbcore: registered new interface driver usbfs [ 0.222025] usbcore: registered new interface driver hub [ 0.222062] usbcore: registered new device driver usb [ 0.223020] EDAC MC: Ver: 3.0.0 [ 0.225007] PCI: Using ACPI for IRQ routing [ 0.225009] PCI: pci_cache_line_size set to 64 bytes [ 0.225199] e820: reserve RAM buffer [mem 0x0009bc00-0x0009ffff] [ 0.225200] e820: reserve RAM buffer [mem 0x09d80000-0x0bffffff] [ 0.225201] e820: reserve RAM buffer [mem 0xc72d0000-0xc7ffffff] [ 0.225202] e820: reserve RAM buffer [mem 0xcd2e7000-0xcfffffff] [ 0.225202] e820: reserve RAM buffer [mem 0xcd4c2000-0xcfffffff] [ 0.225203] e820: reserve RAM buffer [mem 0xcf000000-0xcfffffff] [ 0.225203] e820: reserve RAM buffer [mem 0x42f380000-0x42fffffff] [ 0.225260] NetLabel: Initializing [ 0.225262] NetLabel: domain hash size = 128 [ 0.225264] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.225276] NetLabel: unlabeled traffic allowed by default [ 0.225311] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.225314] hpet0: 3 comparators, 32-bit 14.318180 MHz counter [ 0.227038] clocksource: Switched to clocksource hpet [ 0.230965] VFS: Disk quotas dquot_6.6.0 [ 0.230980] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.231028] pnp: PnP ACPI init [ 0.231109] system 00:00: [mem 0xf8000000-0xfbffffff] has been reserved [ 0.231114] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.231178] system 00:01: [mem 0xfeb80000-0xfebfffff] has been reserved [ 0.231182] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.231262] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.231432] system 00:03: [io 0x0a00-0x0a0f] has been reserved [ 0.231435] system 00:03: [io 0x0a10-0x0a1f] has been reserved [ 0.231437] system 00:03: [io 0x0a20-0x0a2f] has been reserved [ 0.231439] system 00:03: [io 0x0a40-0x0a4f] has been reserved [ 0.231443] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.231727] pnp 00:04: [dma 0 disabled] [ 0.231818] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active) [ 0.231846] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) [ 0.232078] pnp 00:06: [dma 0 disabled] [ 0.232107] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.232347] system 00:07: [io 0x04d0-0x04d1] has been reserved [ 0.232350] system 00:07: [io 0x040b] has been reserved [ 0.232352] system 00:07: [io 0x04d6] has been reserved [ 0.232354] system 00:07: [io 0x0c00-0x0c01] has been reserved [ 0.232357] system 00:07: [io 0x0c14] has been reserved [ 0.232359] system 00:07: [io 0x0c50-0x0c51] has been reserved [ 0.232361] system 00:07: [io 0x0c52] has been reserved [ 0.232363] system 00:07: [io 0x0c6c] has been reserved [ 0.232365] system 00:07: [io 0x0c6f] has been reserved [ 0.232367] system 00:07: [io 0x0cd0-0x0cd1] has been reserved [ 0.232369] system 00:07: [io 0x0cd2-0x0cd3] has been reserved [ 0.232371] system 00:07: [io 0x0cd4-0x0cd5] has been reserved [ 0.232373] system 00:07: [io 0x0cd6-0x0cd7] has been reserved [ 0.232376] system 00:07: [io 0x0cd8-0x0cdf] has been reserved [ 0.232378] system 00:07: [io 0x0800-0x089f] has been reserved [ 0.232380] system 00:07: [io 0x0b00-0x0b0f] has been reserved [ 0.232382] system 00:07: [io 0x0b20-0x0b3f] has been reserved [ 0.232384] system 00:07: [io 0x0900-0x090f] has been reserved [ 0.232385] system 00:07: [io 0x0910-0x091f] has been reserved [ 0.232388] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.232391] system 00:07: [mem 0xfec01000-0xfec01fff] could not be reserved [ 0.232393] system 00:07: [mem 0xfedc0000-0xfedc0fff] has been reserved [ 0.232395] system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.232397] system 00:07: [mem 0xfed80000-0xfed8ffff] could not be reserved [ 0.232400] system 00:07: [mem 0xfec10000-0xfec10fff] has been reserved [ 0.232402] system 00:07: [mem 0xff000000-0xffffffff] has been reserved [ 0.232405] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.232753] pnp: PnP ACPI: found 8 devices [ 0.237952] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.238140] pci 0000:1f:00.0: PCI bridge to [bus 20] [ 0.238145] pci 0000:1f:00.0: bridge window [io 0xe000-0xefff] [ 0.238153] pci 0000:1f:00.0: bridge window [mem 0xf6e00000-0xf6efffff] [ 0.238168] pci 0000:04:00.0: PCI bridge to [bus 1f-20] [ 0.238171] pci 0000:04:00.0: bridge window [io 0xe000-0xefff] [ 0.238176] pci 0000:04:00.0: bridge window [mem 0xf6e00000-0xf6efffff] [ 0.238183] pci 0000:04:01.0: PCI bridge to [bus 21] [ 0.238186] pci 0000:04:01.0: bridge window [io 0xd000-0xdfff] [ 0.238190] pci 0000:04:01.0: bridge window [mem 0xf6d00000-0xf6dfffff] [ 0.238198] pci 0000:24:08.0: PCI bridge to [bus 25] [ 0.238203] pci 0000:24:08.0: bridge window [io 0x9000-0x9fff] [ 0.238214] pci 0000:24:08.0: bridge window [mem 0xf5c00000-0xf5cfffff] [ 0.238235] pci 0000:23:04.0: PCI bridge to [bus 24-25] [ 0.238239] pci 0000:23:04.0: bridge window [io 0x9000-0xafff] [ 0.238248] pci 0000:23:04.0: bridge window [mem 0xf3800000-0xf5dfffff] [ 0.238256] pci 0000:23:04.0: bridge window [mem 0xe0000000-0xe3ffffff 64bit pref] [ 0.238268] pci 0000:22:00.0: PCI bridge to [bus 23-25] [ 0.238272] pci 0000:22:00.0: bridge window [io 0x9000-0xafff] [ 0.238280] pci 0000:22:00.0: bridge window [mem 0xf3800000-0xf5dfffff] [ 0.238286] pci 0000:22:00.0: bridge window [mem 0xe0000000-0xe3ffffff 64bit pref] [ 0.238297] pci 0000:04:04.0: PCI bridge to [bus 22-25] [ 0.238299] pci 0000:04:04.0: bridge window [io 0x9000-0xafff] [ 0.238304] pci 0000:04:04.0: bridge window [mem 0xf3800000-0xf5dfffff] [ 0.238307] pci 0000:04:04.0: bridge window [mem 0xe0000000-0xe3ffffff 64bit pref] [ 0.238313] pci 0000:04:06.0: PCI bridge to [bus 26] [ 0.238316] pci 0000:04:06.0: bridge window [io 0xc000-0xcfff] [ 0.238320] pci 0000:04:06.0: bridge window [mem 0xf6c00000-0xf6cfffff] [ 0.238329] pci 0000:29:05.0: PCI bridge to [bus 2a] [ 0.238340] pci 0000:29:05.0: bridge window [mem 0xf6900000-0xf69fffff] [ 0.238348] pci 0000:29:05.0: bridge window [mem 0xe5000000-0xe5ffffff 64bit pref] [ 0.238362] pci 0000:29:06.0: PCI bridge to [bus 2b] [ 0.238373] pci 0000:29:06.0: bridge window [mem 0xf6800000-0xf68fffff] [ 0.238381] pci 0000:29:06.0: bridge window [mem 0xe4000000-0xe4ffffff 64bit pref] [ 0.238396] pci 0000:28:04.0: PCI bridge to [bus 29-2b] [ 0.238400] pci 0000:28:04.0: bridge window [io 0xb000-0xbfff] [ 0.238409] pci 0000:28:04.0: bridge window [mem 0xf6000000-0xf6afffff] [ 0.238416] pci 0000:28:04.0: bridge window [mem 0xe4000000-0xe5ffffff 64bit pref] [ 0.238428] pci 0000:27:00.0: PCI bridge to [bus 28-2b] [ 0.238432] pci 0000:27:00.0: bridge window [io 0xb000-0xbfff] [ 0.238440] pci 0000:27:00.0: bridge window [mem 0xf6000000-0xf6afffff] [ 0.238447] pci 0000:27:00.0: bridge window [mem 0xe4000000-0xe5ffffff 64bit pref] [ 0.238458] pci 0000:04:07.0: PCI bridge to [bus 27-2b] [ 0.238460] pci 0000:04:07.0: bridge window [io 0xb000-0xbfff] [ 0.238465] pci 0000:04:07.0: bridge window [mem 0xf6000000-0xf6afffff] [ 0.238469] pci 0000:04:07.0: bridge window [mem 0xe4000000-0xe5ffffff 64bit pref] [ 0.238474] pci 0000:03:00.2: PCI bridge to [bus 04-2b] [ 0.238477] pci 0000:03:00.2: bridge window [io 0x9000-0xefff] [ 0.238481] pci 0000:03:00.2: bridge window [mem 0xf3800000-0xf6efffff] [ 0.238485] pci 0000:03:00.2: bridge window [mem 0xe0000000-0xe5ffffff 64bit pref] [ 0.238490] pci 0000:00:01.3: PCI bridge to [bus 03-2b] [ 0.238492] pci 0000:00:01.3: bridge window [io 0x9000-0xefff] [ 0.238496] pci 0000:00:01.3: bridge window [mem 0xf3800000-0xf6ffffff] [ 0.238499] pci 0000:00:01.3: bridge window [mem 0xe0000000-0xe5ffffff 64bit pref] [ 0.238503] pci 0000:00:03.1: PCI bridge to [bus 2c] [ 0.238505] pci 0000:00:03.1: bridge window [io 0xf000-0xffff] [ 0.238509] pci 0000:00:03.1: bridge window [mem 0xf1000000-0xf30fffff] [ 0.238512] pci 0000:00:03.1: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.238517] pci 0000:00:07.1: PCI bridge to [bus 2d] [ 0.238520] pci 0000:00:07.1: bridge window [mem 0xf7000000-0xf72fffff] [ 0.238525] pci 0000:00:08.1: PCI bridge to [bus 2e] [ 0.238528] pci 0000:00:08.1: bridge window [mem 0xf7300000-0xf73fffff] [ 0.238533] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window] [ 0.238534] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window] [ 0.238535] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window] [ 0.238536] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window] [ 0.238537] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window] [ 0.238538] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window] [ 0.238539] pci_bus 0000:00: resource 10 [mem 0xd0000000-0xfec2ffff window] [ 0.238539] pci_bus 0000:00: resource 11 [mem 0xfee00000-0xffffffff window] [ 0.238540] pci_bus 0000:03: resource 0 [io 0x9000-0xefff] [ 0.238541] pci_bus 0000:03: resource 1 [mem 0xf3800000-0xf6ffffff] [ 0.238542] pci_bus 0000:03: resource 2 [mem 0xe0000000-0xe5ffffff 64bit pref] [ 0.238542] pci_bus 0000:04: resource 0 [io 0x9000-0xefff] [ 0.238543] pci_bus 0000:04: resource 1 [mem 0xf3800000-0xf6efffff] [ 0.238544] pci_bus 0000:04: resource 2 [mem 0xe0000000-0xe5ffffff 64bit pref] [ 0.238545] pci_bus 0000:1f: resource 0 [io 0xe000-0xefff] [ 0.238545] pci_bus 0000:1f: resource 1 [mem 0xf6e00000-0xf6efffff] [ 0.238546] pci_bus 0000:20: resource 0 [io 0xe000-0xefff] [ 0.238547] pci_bus 0000:20: resource 1 [mem 0xf6e00000-0xf6efffff] [ 0.238548] pci_bus 0000:21: resource 0 [io 0xd000-0xdfff] [ 0.238548] pci_bus 0000:21: resource 1 [mem 0xf6d00000-0xf6dfffff] [ 0.238549] pci_bus 0000:22: resource 0 [io 0x9000-0xafff] [ 0.238550] pci_bus 0000:22: resource 1 [mem 0xf3800000-0xf5dfffff] [ 0.238551] pci_bus 0000:22: resource 2 [mem 0xe0000000-0xe3ffffff 64bit pref] [ 0.238551] pci_bus 0000:23: resource 0 [io 0x9000-0xafff] [ 0.238552] pci_bus 0000:23: resource 1 [mem 0xf3800000-0xf5dfffff] [ 0.238553] pci_bus 0000:23: resource 2 [mem 0xe0000000-0xe3ffffff 64bit pref] [ 0.238553] pci_bus 0000:24: resource 0 [io 0x9000-0xafff] [ 0.238554] pci_bus 0000:24: resource 1 [mem 0xf3800000-0xf5dfffff] [ 0.238555] pci_bus 0000:24: resource 2 [mem 0xe0000000-0xe3ffffff 64bit pref] [ 0.238556] pci_bus 0000:25: resource 0 [io 0x9000-0x9fff] [ 0.238556] pci_bus 0000:25: resource 1 [mem 0xf5c00000-0xf5cfffff] [ 0.238557] pci_bus 0000:26: resource 0 [io 0xc000-0xcfff] [ 0.238558] pci_bus 0000:26: resource 1 [mem 0xf6c00000-0xf6cfffff] [ 0.238559] pci_bus 0000:27: resource 0 [io 0xb000-0xbfff] [ 0.238559] pci_bus 0000:27: resource 1 [mem 0xf6000000-0xf6afffff] [ 0.238560] pci_bus 0000:27: resource 2 [mem 0xe4000000-0xe5ffffff 64bit pref] [ 0.238561] pci_bus 0000:28: resource 0 [io 0xb000-0xbfff] [ 0.238562] pci_bus 0000:28: resource 1 [mem 0xf6000000-0xf6afffff] [ 0.238562] pci_bus 0000:28: resource 2 [mem 0xe4000000-0xe5ffffff 64bit pref] [ 0.238563] pci_bus 0000:29: resource 0 [io 0xb000-0xbfff] [ 0.238564] pci_bus 0000:29: resource 1 [mem 0xf6000000-0xf6afffff] [ 0.238565] pci_bus 0000:29: resource 2 [mem 0xe4000000-0xe5ffffff 64bit pref] [ 0.238565] pci_bus 0000:2a: resource 1 [mem 0xf6900000-0xf69fffff] [ 0.238566] pci_bus 0000:2a: resource 2 [mem 0xe5000000-0xe5ffffff 64bit pref] [ 0.238567] pci_bus 0000:2b: resource 1 [mem 0xf6800000-0xf68fffff] [ 0.238568] pci_bus 0000:2b: resource 2 [mem 0xe4000000-0xe4ffffff 64bit pref] [ 0.238568] pci_bus 0000:2c: resource 0 [io 0xf000-0xffff] [ 0.238569] pci_bus 0000:2c: resource 1 [mem 0xf1000000-0xf30fffff] [ 0.238570] pci_bus 0000:2c: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.238571] pci_bus 0000:2d: resource 1 [mem 0xf7000000-0xf72fffff] [ 0.238571] pci_bus 0000:2e: resource 1 [mem 0xf7300000-0xf73fffff] [ 0.238630] NET: Registered protocol family 2 [ 0.238727] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.238867] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.238989] TCP: Hash tables configured (established 131072 bind 65536) [ 0.239031] UDP hash table entries: 8192 (order: 6, 262144 bytes) [ 0.239062] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes) [ 0.239125] NET: Registered protocol family 1 [ 0.239255] pci 0000:22:00.0: TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled [ 0.239296] pci 0000:27:00.0: TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled [ 0.239346] pci 0000:2c:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.239438] PCI: CLS 64 bytes, default 64 [ 0.239461] Unpacking initramfs... [ 1.015060] Freeing initrd memory: 8696K [ 1.086318] AMD-Vi: IOMMU performance counters supported [ 1.086396] pci 0000:00:00.2: can't derive routing for PCI INT A [ 1.086399] pci 0000:00:00.2: PCI INT A: not connected [ 1.086607] iommu: Adding device 0000:00:01.0 to group 0 [ 1.086620] iommu: Adding device 0000:00:01.3 to group 0 [ 1.086715] iommu: Adding device 0000:00:02.0 to group 1 [ 1.086805] iommu: Adding device 0000:00:03.0 to group 2 [ 1.086818] iommu: Adding device 0000:00:03.1 to group 2 [ 1.086914] iommu: Adding device 0000:00:04.0 to group 3 [ 1.087021] iommu: Adding device 0000:00:07.0 to group 4 [ 1.087034] iommu: Adding device 0000:00:07.1 to group 4 [ 1.087135] iommu: Adding device 0000:00:08.0 to group 5 [ 1.087148] iommu: Adding device 0000:00:08.1 to group 5 [ 1.087242] iommu: Adding device 0000:00:14.0 to group 6 [ 1.087254] iommu: Adding device 0000:00:14.3 to group 6 [ 1.087383] iommu: Adding device 0000:00:18.0 to group 7 [ 1.087396] iommu: Adding device 0000:00:18.1 to group 7 [ 1.087407] iommu: Adding device 0000:00:18.2 to group 7 [ 1.087420] iommu: Adding device 0000:00:18.3 to group 7 [ 1.087431] iommu: Adding device 0000:00:18.4 to group 7 [ 1.087444] iommu: Adding device 0000:00:18.5 to group 7 [ 1.087456] iommu: Adding device 0000:00:18.6 to group 7 [ 1.087468] iommu: Adding device 0000:00:18.7 to group 7 [ 1.087475] iommu: Adding device 0000:03:00.0 to group 0 [ 1.087481] iommu: Adding device 0000:03:00.1 to group 0 [ 1.087488] iommu: Adding device 0000:03:00.2 to group 0 [ 1.087494] iommu: Adding device 0000:04:00.0 to group 0 [ 1.087502] iommu: Adding device 0000:04:01.0 to group 0 [ 1.087508] iommu: Adding device 0000:04:04.0 to group 0 [ 1.087515] iommu: Adding device 0000:04:06.0 to group 0 [ 1.087521] iommu: Adding device 0000:04:07.0 to group 0 [ 1.087528] iommu: Adding device 0000:1f:00.0 to group 0 [ 1.087534] iommu: Adding device 0000:20:00.0 to group 0 [ 1.087541] iommu: Adding device 0000:20:01.0 to group 0 [ 1.087547] iommu: Adding device 0000:21:00.0 to group 0 [ 1.087554] iommu: Adding device 0000:22:00.0 to group 0 [ 1.087562] iommu: Adding device 0000:23:04.0 to group 0 [ 1.087569] iommu: Adding device 0000:24:04.0 to group 0 [ 1.087576] iommu: Adding device 0000:24:05.0 to group 0 [ 1.087583] iommu: Adding device 0000:24:06.0 to group 0 [ 1.087590] iommu: Adding device 0000:24:07.0 to group 0 [ 1.087597] iommu: Adding device 0000:24:08.0 to group 0 [ 1.087604] iommu: Adding device 0000:24:09.0 to group 0 [ 1.087611] iommu: Adding device 0000:24:0a.0 to group 0 [ 1.087617] iommu: Adding device 0000:25:00.0 to group 0 [ 1.087624] iommu: Adding device 0000:26:00.0 to group 0 [ 1.087632] iommu: Adding device 0000:27:00.0 to group 0 [ 1.087639] iommu: Adding device 0000:28:04.0 to group 0 [ 1.087646] iommu: Adding device 0000:29:04.0 to group 0 [ 1.087652] iommu: Adding device 0000:29:05.0 to group 0 [ 1.087659] iommu: Adding device 0000:29:06.0 to group 0 [ 1.087666] iommu: Adding device 0000:29:07.0 to group 0 [ 1.087672] iommu: Adding device 0000:29:08.0 to group 0 [ 1.087679] iommu: Adding device 0000:29:0a.0 to group 0 [ 1.087686] iommu: Adding device 0000:2a:00.0 to group 0 [ 1.087693] iommu: Adding device 0000:2b:00.0 to group 0 [ 1.087699] iommu: Adding device 0000:2c:00.0 to group 2 [ 1.087706] iommu: Adding device 0000:2d:00.0 to group 4 [ 1.087714] iommu: Adding device 0000:2d:00.2 to group 4 [ 1.087721] iommu: Adding device 0000:2d:00.3 to group 4 [ 1.087728] iommu: Adding device 0000:2e:00.0 to group 5 [ 1.087735] iommu: Adding device 0000:2e:00.2 to group 5 [ 1.087743] iommu: Adding device 0000:2e:00.3 to group 5 [ 1.087857] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40 [ 1.087859] AMD-Vi: Extended features (0xf77ef22294ada): [ 1.087861] PPR NX GT IA GA PC GA_vAPIC [ 1.087927] AMD-Vi: Lazy IO/TLB flushing enabled [ 1.088708] amd_uncore: AMD NB counters detected [ 1.088713] amd_uncore: AMD LLC counters detected [ 1.089388] perf/amd_iommu: Detected AMD IOMMU #0 (2 banks, 4 counters/bank). [ 1.090809] Initialise system trusted keyrings [ 1.090839] workingset: timestamp_bits=46 max_order=22 bucket_order=0 [ 1.091445] zbud: loaded [ 1.092161] Key type asymmetric registered [ 1.092180] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 1.092183] io scheduler noop registered [ 1.092185] io scheduler deadline registered [ 1.092207] io scheduler cfq registered (default) [ 1.092209] io scheduler mq-deadline registered [ 1.093154] pcieport 0000:00:01.3: Signaling PME with IRQ 26 [ 1.093226] pcieport 0000:00:03.1: Signaling PME with IRQ 27 [ 1.093242] pcieport 0000:00:07.1: Signaling PME with IRQ 28 [ 1.093258] pcieport 0000:00:08.1: Signaling PME with IRQ 30 [ 1.093281] vesafb: mode is 1280x1024x32, linelength=5120, pages=0 [ 1.093283] vesafb: scrolling: redraw [ 1.093285] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 [ 1.093294] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90000800000, using 5120k, total 5120k [ 1.136485] Console: switching to colour frame buffer device 160x64 [ 1.179882] fb0: VESA VGA frame buffer device [ 1.180149] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 1.201385] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 1.202039] Non-volatile memory driver v1.3 [ 1.202251] Linux agpgart interface v0.103 [ 1.203778] ahci 0000:03:00.1: version 3.0 [ 1.203853] ahci 0000:03:00.1: SSS flag set, parallel bus scan disabled [ 1.204220] ahci 0000:03:00.1: AHCI 0001.0301 32 slots 8 ports 6 Gbps 0x33 impl SATA mode [ 1.204613] ahci 0000:03:00.1: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part sxs deso sadm sds apst [ 1.206497] scsi host0: ahci [ 1.207703] scsi host1: ahci [ 1.208899] scsi host2: ahci [ 1.210133] scsi host3: ahci [ 1.211331] scsi host4: ahci [ 1.212525] scsi host5: ahci [ 1.213725] scsi host6: ahci [ 1.214920] scsi host7: ahci [ 1.215087] ata1: SATA max UDMA/133 abar m131072@0xf6f80000 port 0xf6f80100 irq 35 [ 1.215452] ata2: SATA max UDMA/133 abar m131072@0xf6f80000 port 0xf6f80180 irq 35 [ 1.215815] ata3: DUMMY [ 1.215927] ata4: DUMMY [ 1.216056] ata5: SATA max UDMA/133 abar m131072@0xf6f80000 port 0xf6f80300 irq 35 [ 1.216420] ata6: SATA max UDMA/133 abar m131072@0xf6f80000 port 0xf6f80380 irq 35 [ 1.216783] ata7: DUMMY [ 1.216900] ata8: DUMMY [ 1.227248] ahci 0000:26:00.0: AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode [ 1.227638] ahci 0000:26:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.229312] scsi host8: ahci [ 1.230512] scsi host9: ahci [ 1.231711] scsi host10: ahci [ 1.232912] scsi host11: ahci [ 1.233084] ata9: SATA max UDMA/133 abar m2048@0xf6c10000 port 0xf6c10100 irq 36 [ 1.233441] ata10: SATA max UDMA/133 abar m2048@0xf6c10000 port 0xf6c10180 irq 36 [ 1.233801] ata11: SATA max UDMA/133 abar m2048@0xf6c10000 port 0xf6c10200 irq 36 [ 1.234173] ata12: SATA max UDMA/133 abar m2048@0xf6c10000 port 0xf6c10280 irq 36 [ 1.234619] ahci 0000:2e:00.2: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode [ 1.235020] ahci 0000:2e:00.2: flags: 64bit ncq sntf ilck led clo only pmp fbs pio [ 1.236510] scsi host12: ahci [ 1.236671] ata13: SATA max UDMA/133 abar m4096@0xf7308000 port 0xf7308100 irq 38 [ 1.237052] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.248248] ehci-pci: EHCI PCI platform driver [ 1.259401] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.270697] uhci_hcd: USB Universal Host Controller Interface driver [ 1.282143] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 [ 1.293597] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp [ 1.305823] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.317455] mousedev: PS/2 mouse device common for all mice [ 1.329099] rtc_cmos 00:02: RTC can wake from S4 [ 1.340893] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 1.352504] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 1.364422] ledtrig-cpu: registered to indicate activity on CPUs [ 1.376082] hidraw: raw HID events driver (C) Jiri Kosina [ 1.387882] usbcore: registered new interface driver usbhid [ 1.399740] usbhid: USB HID core driver [ 1.411744] NET: Registered protocol family 10 [ 1.423770] Segment Routing with IPv6 [ 1.427253] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 1.448191] Key type dns_resolver registered [ 1.473416] microcode: CPU0: patch_level=0x08001129 [ 1.485993] microcode: CPU1: patch_level=0x08001129 [ 1.498413] microcode: CPU2: patch_level=0x08001129 [ 1.510690] microcode: CPU3: patch_level=0x08001129 [ 1.522758] microcode: CPU4: patch_level=0x08001129 [ 1.534544] microcode: CPU5: patch_level=0x08001129 [ 1.546085] microcode: CPU6: patch_level=0x08001129 [ 1.557437] microcode: CPU7: patch_level=0x08001129 [ 1.568513] microcode: CPU8: patch_level=0x08001129 [ 1.579396] microcode: CPU9: patch_level=0x08001129 [ 1.590045] microcode: CPU10: patch_level=0x08001129 [ 1.600683] microcode: CPU11: patch_level=0x08001129 [ 1.611104] microcode: CPU12: patch_level=0x08001129 [ 1.621314] microcode: CPU13: patch_level=0x08001129 [ 1.631214] microcode: CPU14: patch_level=0x08001129 [ 1.640771] microcode: CPU15: patch_level=0x08001129 [ 1.645377] ata13: SATA link down (SStatus 0 SControl 300) [ 1.660111] microcode: Microcode Update Driver: v2.2. [ 1.660119] sched_clock: Marking stable (1660100924, 0)->(1778206391, -118105467) [ 1.680035] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.680834] ata1.00: FORCE: horkage modified (noncq) [ 1.701753] registered taskstats version 1 [ 1.712503] Loading compiled-in X.509 certificates [ 1.720042] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.720817] ata9.00: FORCE: horkage modified (noncq) [ 1.721248] ata9.00: ATA-6: ST3500320NS, SN04, max UDMA/133 [ 1.721249] ata9.00: 976773168 sectors, multi 0: LBA48 NCQ (not used) [ 1.722804] ata9.00: configured for UDMA/133 [ 1.724957] ata1.00: ATA-7: ST3160815AS, 3.AAD, max UDMA/133 [ 1.724957] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (not used) [ 1.752043] ata10: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 1.753528] ata10.00: FORCE: horkage modified (noncq) [ 1.753619] ata10.00: supports DRM functions and may not be fully accessible [ 1.753620] ata10.00: ATA-9: Samsung SSD 850 EVO 500GB, EMT02B6Q, max UDMA/133 [ 1.753620] ata10.00: 976773168 sectors, multi 1: LBA48 NCQ (not used) [ 1.755410] ata10.00: supports DRM functions and may not be fully accessible [ 1.756708] ata10.00: configured for UDMA/133 [ 1.768039] ata11: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.769556] ata11.00: FORCE: horkage modified (noncq) [ 1.776039] ata12: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.776944] ata12.00: FORCE: horkage modified (noncq) [ 1.777102] ata12.00: ATA-8: ST3500418AS, CC38, max UDMA/133 [ 1.777103] ata12.00: 976773168 sectors, multi 0: LBA48 NCQ (not used) [ 1.778328] ata12.00: configured for UDMA/133 [ 1.783259] ata1.00: configured for UDMA/133 [ 1.783337] scsi 0:0:0:0: Direct-Access ATA ST3160815AS D PQ: 0 ANSI: 5 [ 1.783472] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 1.783480] sd 0:0:0:0: [sda] Write Protect is off [ 1.783481] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.783494] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.797061] ata11.00: ATA-8: ST3500320NS, SN06, max UDMA/133 [ 1.797062] ata11.00: 976773168 sectors, multi 0: LBA48 NCQ (not used) [ 1.839465] ata11.00: configured for UDMA/133 [ 1.886414] sda: sda1 sda2 sda3 < sda5 sda6 sda7 > [ 1.886701] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.079124] zswap: loaded using pool lzo/zbud [ 2.091175] Magic number: 9:611:991 [ 2.102317] machinecheck machinecheck4: hash matches [ 2.113591] rtc_cmos 00:02: setting system clock to 2017-11-22 14:59:57 UTC (1511362797) [ 2.144063] tsc: Refined TSC clocksource calibration: 2999.997 MHz [ 2.155533] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2b3e4269d76, max_idle_ns: 440795235636 ns [ 2.248065] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.261085] ata2.00: FORCE: horkage modified (noncq) [ 2.314441] ata2.00: ATA-7: ST3160815AS, 4.AAB, max UDMA/133 [ 2.326091] ata2.00: 312581808 sectors, multi 16: LBA48 NCQ (not used) [ 2.372742] ata2.00: configured for UDMA/133 [ 2.394662] scsi 1:0:0:0: Direct-Access ATA ST3160815AS B PQ: 0 ANSI: 5 [ 2.406964] sd 1:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 2.419411] sd 1:0:0:0: [sdb] Write Protect is off [ 2.431911] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2.431917] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.516818] sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 sdb7 > [ 2.530105] sd 1:0:0:0: [sdb] Attached SCSI disk [ 2.872065] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.886248] ata5.00: FORCE: horkage modified (noncq) [ 2.933706] ata5.00: ATA-7: ST3160811AS, 3.AAE, max UDMA/133 [ 2.947382] ata5.00: 312581808 sectors, multi 16: LBA48 NCQ (not used) [ 2.992010] ata5.00: configured for UDMA/133 [ 3.016113] scsi 4:0:0:0: Direct-Access ATA ST3160811AS E PQ: 0 ANSI: 5 [ 3.030587] sd 4:0:0:0: [sdc] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 3.045252] sd 4:0:0:0: [sdc] Write Protect is off [ 3.059969] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 3.059976] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.167263] sdc: sdc1 sdc2 sdc3 < sdc5 sdc6 sdc7 > [ 3.182194] clocksource: Switched to clocksource tsc [ 3.197185] sd 4:0:0:0: [sdc] Attached SCSI disk [ 3.496055] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 3.512416] ata6.00: FORCE: horkage modified (noncq) [ 3.527191] ata6.00: ATAPI: SONY DVD RW AD-7260S, 1.61, max UDMA/100 [ 3.543874] ata6.00: configured for UDMA/100 [ 3.570401] scsi 5:0:0:0: CD-ROM SONY DVD RW AD-7260S 1.61 PQ: 0 ANSI: 5 [ 3.596801] scsi 8:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 [ 3.611881] sd 8:0:0:0: [sdd] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 3.626967] scsi 9:0:0:0: Direct-Access ATA Samsung SSD 850 2B6Q PQ: 0 ANSI: 5 [ 3.642139] sd 8:0:0:0: [sdd] Write Protect is off [ 3.657296] sd 8:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [ 3.657312] sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.657315] sd 9:0:0:0: [sde] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 3.657320] sd 9:0:0:0: [sde] Write Protect is off [ 3.657320] sd 9:0:0:0: [sde] Mode Sense: 00 3a 00 00 [ 3.657327] sd 9:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.657373] scsi 10:0:0:0: Direct-Access ATA ST3500320NS SN06 PQ: 0 ANSI: 5 [ 3.657580] scsi 11:0:0:0: Direct-Access ATA ST3500418AS CC38 PQ: 0 ANSI: 5 [ 3.657694] sd 10:0:0:0: [sdf] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 3.657730] sd 10:0:0:0: [sdf] Write Protect is off [ 3.657731] sd 10:0:0:0: [sdf] Mode Sense: 00 3a 00 00 [ 3.657745] sd 10:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.657760] sd 11:0:0:0: [sdg] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 3.657806] sd 11:0:0:0: [sdg] Write Protect is off [ 3.657807] sd 11:0:0:0: [sdg] Mode Sense: 00 3a 00 00 [ 3.657851] sd 11:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.659053] sde: sde1 [ 3.659231] sd 9:0:0:0: [sde] Attached SCSI removable disk [ 3.664513] sdg: sdg1 [ 3.664700] sd 11:0:0:0: [sdg] Attached SCSI removable disk [ 3.664835] sdf: sdf1 [ 3.664962] sd 10:0:0:0: [sdf] Attached SCSI removable disk [ 3.943171] sdd: sdd1 [ 3.958445] sd 8:0:0:0: [sdd] Attached SCSI removable disk [ 3.974385] Freeing unused kernel memory: 1072K [ 3.989493] Write protecting the kernel read-only data: 12288k [ 4.004901] Freeing unused kernel memory: 1120K [ 4.022064] Freeing unused kernel memory: 1124K [ 4.043217] systemd[1]: systemd 228 running in system mode. (+PAM -AUDIT +SELINUX -IMA +APPARMOR -SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT -GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 4.075133] systemd[1]: Detected architecture x86-64. [ 4.091063] systemd[1]: Running in initial RAM disk. [ 4.152272] systemd[1]: Set hostname to <harley>. [ 4.189592] systemd[1]: Created slice System Slice. [ 4.219976] systemd[1]: Listening on Journal Socket (/dev/log). [ 4.250443] systemd[1]: Reached target Local File Systems. [ 4.280616] systemd[1]: Listening on udev Kernel Socket. [ 4.310883] systemd[1]: Reached target Slices. [ 4.340651] systemd[1]: Reached target Timers. [ 4.466858] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 4.466976] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 4.467098] sd 4:0:0:0: Attached scsi generic sg2 type 0 [ 4.467194] scsi 5:0:0:0: Attached scsi generic sg3 type 5 [ 4.467297] sd 8:0:0:0: Attached scsi generic sg4 type 0 [ 4.467396] sd 9:0:0:0: Attached scsi generic sg5 type 0 [ 4.467492] sd 10:0:0:0: Attached scsi generic sg6 type 0 [ 4.467593] sd 11:0:0:0: Attached scsi generic sg7 type 0 [ 4.879069] random: crng init done [ 4.931935] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1 [ 4.945166] ACPI: Power Button [PWRB] [ 4.961083] QUIRK: Enable AMD PLL fix [ 4.961105] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 4.961114] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1 [ 4.968455] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 4.968523] ACPI: Power Button [PWRF] [ 4.972663] sr 5:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 4.972664] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 4.972777] sr 5:0:0:0: Attached scsi CD-ROM sr0 [ 5.016460] xhci_hcd 0000:03:00.0: hcc params 0x0200ef81 hci version 0x110 quirks 0x00000418 [ 5.016540] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 5.016541] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.016542] usb usb1: Product: xHCI Host Controller [ 5.016543] usb usb1: Manufacturer: Linux 4.14.1-lcrs xhci-hcd [ 5.016543] usb usb1: SerialNumber: 0000:03:00.0 [ 5.016633] hub 1-0:1.0: USB hub found [ 5.016645] hub 1-0:1.0: 10 ports detected [ 5.016881] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 5.016883] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 2 [ 5.016885] xhci_hcd 0000:03:00.0: Host supports USB 3.1 Enhanced SuperSpeed [ 5.016906] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.016920] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 5.016921] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.016922] usb usb2: Product: xHCI Host Controller [ 5.016922] usb usb2: Manufacturer: Linux 4.14.1-lcrs xhci-hcd [ 5.016923] usb usb2: SerialNumber: 0000:03:00.0 [ 5.016979] hub 2-0:1.0: USB hub found [ 5.016985] hub 2-0:1.0: 4 ports detected [ 5.017175] xhci_hcd 0000:2d:00.3: xHCI Host Controller [ 5.017178] xhci_hcd 0000:2d:00.3: new USB bus registered, assigned bus number 3 [ 5.017282] xhci_hcd 0000:2d:00.3: hcc params 0x0270f665 hci version 0x100 quirks 0x00000418 [ 5.017331] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 5.017331] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.017332] usb usb3: Product: xHCI Host Controller [ 5.017333] usb usb3: Manufacturer: Linux 4.14.1-lcrs xhci-hcd [ 5.017333] usb usb3: SerialNumber: 0000:2d:00.3 [ 5.017393] hub 3-0:1.0: USB hub found [ 5.017398] hub 3-0:1.0: 4 ports detected [ 5.017527] xhci_hcd 0000:2d:00.3: xHCI Host Controller [ 5.017529] xhci_hcd 0000:2d:00.3: new USB bus registered, assigned bus number 4 [ 5.017538] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.017549] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 5.017550] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.017551] usb usb4: Product: xHCI Host Controller [ 5.017551] usb usb4: Manufacturer: Linux 4.14.1-lcrs xhci-hcd [ 5.017552] usb usb4: SerialNumber: 0000:2d:00.3 [ 5.017607] hub 4-0:1.0: USB hub found [ 5.017612] hub 4-0:1.0: 4 ports detected [ 5.408052] usb 1-8: new full-speed USB device number 2 using xhci_hcd [ 5.810517] usb 1-8: New USB device found, idVendor=12cf, idProduct=0155 [ 5.810841] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.811189] usb 1-8: Product: CM STORM SENTINEL GAMING MOUSE [ 5.811461] usb 1-8: Manufacturer: DEXIN Corporation [ 5.832392] input: DEXIN Corporation CM STORM SENTINEL GAMING MOUSE as /devices/pci0000:00/0000:00:01.3/0000:03:00.0/usb1/1-8/1-8:1.0/0003:12CF:0155.0001/input/input3 [ 5.833172] hid-generic 0003:12CF:0155.0001: input,hidraw0: USB HID v1.11 Mouse [DEXIN Corporation CM STORM SENTINEL GAMING MOUSE] on usb-0000:03:00.0-8/input0 [ 5.848407] input: DEXIN Corporation CM STORM SENTINEL GAMING MOUSE as /devices/pci0000:00/0000:00:01.3/0000:03:00.0/usb1/1-8/1-8:1.1/0003:12CF:0155.0002/input/input4 [ 5.901103] hid-generic 0003:12CF:0155.0002: input,hidraw1: USB HID v1.11 Keyboard [DEXIN Corporation CM STORM SENTINEL GAMING MOUSE] on usb-0000:03:00.0-8/input1 [ 6.097251] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) [ 20.448060] scsi host13: Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 <Adaptec 2930CU SCSI adapter> aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs [ 21.239394] scsi 13:0:3:0: Sequential-Access SONY SDT-10000 0110 PQ: 0 ANSI: 2 [ 21.239791] scsi target13:0:3: Beginning Domain Validation [ 21.247921] scsi target13:0:3: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 15) [ 21.253511] scsi target13:0:3: Domain Validation skipping write tests [ 21.253821] scsi target13:0:3: Ending Domain Validation [ 21.254191] scsi 13:0:3:0: Attached scsi generic sg8 type 1 [ 37.344056] scsi host14: Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 <Adaptec 2930CU SCSI adapter> aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs [ 37.611894] scsi 14:0:1:0: Sequential-Access HP 88780 A674 PQ: 0 ANSI: 1 CCS [ 37.627663] scsi target14:0:1: Beginning Domain Validation [ 37.661968] scsi target14:0:1: Ending Domain Validation [ 37.677696] scsi 14:0:1:0: Attached scsi generic sg9 type 1 [ 39.028385] scsi 14:0:6:0: Sequential-Access EXABYTE EXB-8500-85Qanx0 0446 PQ: 0 ANSI: 2 [ 39.044269] scsi target14:0:6: Beginning Domain Validation [ 39.887987] scsi target14:0:6: FAST-5 SCSI 4.0 MB/s ST (248 ns, offset 11) [ 39.982615] scsi target14:0:6: Domain Validation skipping write tests [ 39.998192] scsi target14:0:6: Ending Domain Validation [ 40.013729] scsi 14:0:6:0: Attached scsi generic sg10 type 1 [ 40.247693] systemd-journald[243]: Received SIGTERM from PID 1 (systemd). [ 40.452755] systemd: 15 output lines suppressed due to ratelimiting [ 44.411868] EXT4-fs (sda5): re-mounted. Opts: acl,user_xattr [ 44.692931] systemd-journald[573]: Received request to flush runtime journal from PID 1 [ 52.975270] Warning: Processor Platform Limit event detected, but not handled. [ 52.987205] Consider compiling CPUfreq support into your kernel. [ 53.251769] parport_pc 00:04: reported by Plug and Play ACPI [ 53.263825] parport0: PC-style at 0x378, irq 5 [PCSPP(,...)] [ 53.420232] ppdev: user-space parallel port driver [ 53.542130] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 53.581949] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 53.737463] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0 [ 53.750027] piix4_smbus 0000:00:14.0: Using register 0x02 for SMBus port selection [ 53.884057] st: Version 20160209, fixed bufsize 32768, s/g segs 256 [ 53.897018] st 13:0:3:0: Attached scsi tape st0 [ 53.909485] st 13:0:3:0: st0: try direct i/o: yes (alignment 4 B) [ 53.922227] st 14:0:1:0: Attached scsi tape st1 [ 53.934682] st 14:0:1:0: st1: try direct i/o: yes (alignment 4 B) [ 53.947802] st 14:0:6:0: Attached scsi tape st2 [ 53.959916] st 14:0:6:0: st2: try direct i/o: yes (alignment 4 B) [ 54.154773] AVX2 version of gcm_enc/dec engaged. [ 54.167456] AES CTR mode by8 optimization enabled [ 54.180295] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 54.193141] osst :I: Tape driver with OnStream support version 0.99.4 osst :I: $Id: osst.c,v 1.1.1.1 2017/11/21 13:39:46 markh Exp $ [ 54.197152] r8169 0000:21:00.0 eth0: RTL8168h/8111h at 0xffffc9000006d000, 4c:cc:6a:f8:60:b8, XID 14100800 IRQ 42 [ 54.197154] r8169 0000:21:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 54.544961] rtom: loading out-of-tree module taints kernel. [ 54.552562] gpiohsd: loading out-of-tree module taints kernel. [ 54.559061] gpiohsd: brd 0: PCI BUS 24 SLOT 4 PCI HSD 462 Revision U [ 54.586978] pciiom: Driver revision @(#)(Compro)$Id: pciiom.c,v 1.60 2017/03/14 12:24:41 markh Exp $ date 11-22-2017-08-14 [ 54.601598] RTOM: Board 0 Revision B found [ 54.601673] RTOM: Registered Board 0 irq 33 with rtom_int_handler0 [ 54.630542] pciiom: board 0 PCI BUS 25 SLOT 0 DEV ID 100 SUBDEV ID = 4700 Prototype 0x31 [ 54.645420] hdlc: HDLC support module revision 1.22 [ 54.795897] 3c59x: Donald Becker and others. [ 54.810617] 0000:29:04.0: 3Com PCI 3c905C Tornado at ffffc90000075000. [ 54.869410] gpiohsd: brd 0: PCI HSD FLASH Mar 18 2015 18:01:29 [ 54.869611] gpiohsd: brd 1: PCI BUS 24 SLOT 5 PCI HSD 462 Revision U [ 54.918660] SyncLink GT 4.96 [ 54.936404] SyncLink GT 4.96, tty major#244 [ 54.936474] SyncLink GT4 ttySLG0 IO=f6a30000 IRQ=33 maxframe=4096 dma_buffers=128 [ 54.936606] SyncLink GT4 ttySLG1 IO=f6a30000 IRQ=33 maxframe=4096 dma_buffers=128 [ 54.936717] SyncLink GT4 ttySLG2 IO=f6a30000 IRQ=33 maxframe=4096 dma_buffers=128 [ 54.936810] SyncLink GT4 ttySLG3 IO=f6a30000 IRQ=33 maxframe=4096 dma_buffers=128 [ 54.979564] dgap: module is from the staging directory, the quality is unknown, you have been warned. [ 55.014780] dgap: dgap-1.3-16, Digi International Part Number 40002347_C [ 55.014781] dgap: For the tools package please visit http://www.digi.com [ 55.203824] gpiohsd: brd 1: PCI HSD FLASH Mar 18 2015 18:01:29 [ 55.203969] eprm: board 0 PCI RMS 436 Revision M [ 55.204004] eprm: board 0 Memory SRAM 8 MB LOCK 8 MB MC 0x100000 B [ 55.204036] eprm: board 0 Serial Link Node ID 74 bus 36 slot 10 [ 55.205586] dgap: dgap: board 0: AccelePort Xr920 8 port (rev 1), irq 33 [ 55.358597] Adding 8385532k swap on /dev/sdb2. Priority:-2 extents:1 across:8385532k FS [ 55.754669] nvidia: module license 'NVIDIA' taints kernel. [ 55.770138] Disabling lock debugging due to kernel taint [ 56.044437] nvidia 0000:2c:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=io+mem [ 56.060554] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.137 Thu Sep 14 13:51:03 PDT 2017 [ 56.578968] kvm: disabled by bios [ 56.843722] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC892: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line [ 56.860505] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 56.877376] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0) [ 56.893348] Adding 8385532k swap on /dev/sda2. Priority:-3 extents:1 across:8385532k FS [ 56.910205] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 [ 56.910207] snd_hda_codec_realtek hdaudioC0D0: inputs: [ 56.910209] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19 [ 56.910210] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18 [ 56.910212] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a [ 56.990364] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:08.1/0000:2e:00.3/sound/card0/input6 [ 56.990405] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:08.1/0000:2e:00.3/sound/card0/input7 [ 56.990475] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:08.1/0000:2e:00.3/sound/card0/input8 [ 56.990539] input: HD-Audio Generic Line Out Front as /devices/pci0000:00/0000:00:08.1/0000:2e:00.3/sound/card0/input9 [ 56.990596] input: HD-Audio Generic Line Out Surround as /devices/pci0000:00/0000:00:08.1/0000:2e:00.3/sound/card0/input10 [ 56.990667] input: HD-Audio Generic Line Out CLFE as /devices/pci0000:00/0000:00:08.1/0000:2e:00.3/sound/card0/input11 [ 56.990773] input: HD-Audio Generic Line Out Side as /devices/pci0000:00/0000:00:08.1/0000:2e:00.3/sound/card0/input12 [ 56.991552] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:08.1/0000:2e:00.3/sound/card0/input13 [ 57.501992] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts: (null) [ 57.510646] EXT4-fs (sdg1): mounted filesystem with ordered data mode. Opts: (null) [ 57.553029] EXT4-fs (sdf1): mounted filesystem with ordered data mode. Opts: acl,user_xattr [ 57.848643] EXT4-fs (sdb5): mounted filesystem with ordered data mode. Opts: acl,user_xattr [ 57.987114] EXT4-fs (sdc5): mounted filesystem with ordered data mode. Opts: acl,user_xattr [ 58.052982] EXT4-fs (sdb6): mounted filesystem with ordered data mode. Opts: (null) [ 58.108985] EXT4-fs (sdb7): mounted filesystem with ordered data mode. Opts: (null) [ 58.114769] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: acl,user_xattr [ 58.154151] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: acl,user_xattr [ 58.174961] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: acl,user_xattr [ 58.231409] EXT4-fs (sdc6): mounted filesystem with ordered data mode. Opts: acl,user_xattr [ 58.308001] EXT4-fs (sdc7): mounted filesystem with ordered data mode. Opts: acl,user_xattr [ 58.832545] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 59.182421] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: acl,user_xattr [ 60.546102] gpiohsd: brd 2: PCI BUS 24 SLOT 6 PCI HSD 462 Revision U [ 60.858630] gpiohsd: brd 2: PCI HSD FLASH Mar 18 2015 18:01:29 [ 60.872556] gpiohsd: brd 3: PCI BUS 24 SLOT 7 PCI HSD 462 Revision U [ 61.209105] gpiohsd: brd 3: PCI HSD FLASH Mar 18 2015 18:01:29 [ 61.223335] gpiohsd: brd 4: PCI BUS 29 SLOT 7 PCI HSD 462 Revision U [ 61.544057] gpiohsd: brd 4: PCI HSD FLASH Jun 11 2014 19:19:11 [ 61.558206] gpiohsd: brd 5: PCI BUS 2a SLOT 0 PCI HSD 471 Revision C [ 62.482478] gpiohsd: brd 6: PCI BUS 2b SLOT 0 PCI HSD 471 Revision C [ 63.846697] No iBFT detected. [ 64.336905] r8169 0000:21:00.0 eth0: link down [ 64.336908] r8169 0000:21:00.0 eth0: link down [ 64.360266] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 64.375373] eth1: setting full-duplex. [ 65.251855] NET: Registered protocol family 17 [ 67.230341] r8169 0000:21:00.0 eth0: link up [ 67.241824] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 81.465934] resource sanity check: requesting [mem 0x000a0000-0x000fffff], which spans more than PCI Bus 0000:00 [mem 0x000a0000-0x000bffff window] [ 81.466017] caller os_map_kernel_space+0x84/0xb0 [nvidia] mapping multiple BARs [ 82.439180] NVRM: Your system is not currently configured to drive a VGA console [ 82.439184] NVRM: on the primary VGA device. The NVIDIA Linux graphics driver [ 82.439185] NVRM: requires the use of a text-mode VGA console. Use of other console [ 82.439186] NVRM: drivers including, but not limited to, vesafb, may result in [ 82.439187] NVRM: corruption and stability problems, and is not supported. [ 297.035844] fuse init (API version 7.26) Thanks Mark ��.n��������+%������w��{.n�����{��'^�)�� jg��� �����ݢj����G���� ���j:+v���w�m������w�������h�����٥
