Some small things, but generally this is starting to look good. Can
probably wait for other people's reviews before v5.
On 06/02/2017 03:53 PM, Preetham Chandru Ramchandra wrote:
From: Preetham Chandru R <pchandru@xxxxxxxxxx>
1. Move tegra124 specifics to tegra124_ahci_init.
2. Separate the regulators needed for tegra124 and tegra210.
3. Disable DIPM for t210 and t124 as there are known issues.
4. Disable Devslp for t210 since devslp pin is shared with
pcie clkreq.
Signed-off-by: Preetham Chandru R <pchandru@xxxxxxxxxx>
---
v4:
* Instead of disabling DIPM through quirk function,
hardcode by adding ATA_FLAG_NO_DIPM to
ahci_tegra_port_info's static definition
* Changed access to aux register to optional because for T124,
we need to continue to support older device trees without
the aux_regs property
v3:
* Remove inline functions for read/write and modify to
SATA, SATA Config and SATA Aux registers.
* Add code to disable DIPM and DevSlp for t210 and t124
v2:
* Fix indentation issues
* Move the change to disable DIPM, HIPM, DevSlp, partial,
slumber and NCQ into a separate patch
---
drivers/ata/ahci_tegra.c | 386 ++++++++++++++++++++++++++++++++++++-----------
1 file changed, 302 insertions(+), 84 deletions(-)
diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c
index 3a62eb2..75520e5 100644
--- a/drivers/ata/ahci_tegra.c
+++ b/drivers/ata/ahci_tegra.c
@@ -34,7 +34,8 @@
#define DRV_NAME "tegra-ahci"
#define SATA_CONFIGURATION_0 0x180
-#define SATA_CONFIGURATION_EN_FPCI BIT(0)
+#define SATA_CONFIGURATION_0_EN_FPCI BIT(0)
+#define SATA_CONFIGURATION_0_CLK_OVERRIDE BIT(31)
#define SCFG_OFFSET 0x1000
@@ -45,17 +46,55 @@
#define T_SATA0_CFG_1_SERR BIT(8)
#define T_SATA0_CFG_9 0x24
-#define T_SATA0_CFG_9_BASE_ADDRESS_SHIFT 13
+#define T_SATA0_CFG_9_BASE_ADDRESS 0x40020000
#define SATA_FPCI_BAR5 0x94
-#define SATA_FPCI_BAR5_START_SHIFT 4
+#define SATA_FPCI_BAR5_START_MASK (0xfffffff << 4)
+#define SATA_FPCI_BAR5_START (0x0040020 << 4)
+#define SATA_FPCI_BAR5_ACCESS_TYPE (0x1)
#define SATA_INTR_MASK 0x188
#define SATA_INTR_MASK_IP_INT_MASK BIT(16)
+#define T_SATA0_CFG_35 0x94
+#define T_SATA0_CFG_35_IDP_INDEX_MASK (0x7ff << 2)
+#define T_SATA0_CFG_35_IDP_INDEX (0x2a << 2)
+
+#define T_SATA0_AHCI_IDP1 0x98
+#define T_SATA0_AHCI_IDP1_DATA (0x400040)
+
+#define T_SATA0_CFG_PHY_1 0x12c
+#define T_SATA0_CFG_PHY_1_PADS_IDDQ_EN BIT(23)
+#define T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN BIT(22)
+
+#define T_SATA0_NVOOB 0x114
+#define T_SATA0_NVOOB_COMMA_CNT_MASK (0xff << 16)
+#define T_SATA0_NVOOB_COMMA_CNT (0x07 << 16)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK (0x3 << 24)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE (0x1 << 24)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK (0x3 << 26)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH (0x3 << 26)
+
+#define T_SATA_CFG_PHY_0 0x120
+#define T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD BIT(11)
+#define T_SATA_CFG_PHY_0_MASK_SQUELCH BIT(24)
+
+#define T_SATA0_CFG2NVOOB_2 0x134
+#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK (0x1ff << 18)
+#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW (0xc << 18)
+
#define T_SATA0_AHCI_HBA_CAP_BKDR 0x300
+#define T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP BIT(13)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP BIT(14)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SALP BIT(26)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM BIT(17)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SNCQ BIT(30)
#define T_SATA0_BKDOOR_CC 0x4a4
+#define T_SATA0_BKDOOR_CC_CLASS_CODE_MASK (0xffff << 16)
+#define T_SATA0_BKDOOR_CC_CLASS_CODE (0x0106 << 16)
+#define T_SATA0_BKDOOR_CC_PROG_IF_MASK (0xff << 8)
+#define T_SATA0_BKDOOR_CC_PROG_IF (0x01 << 8)
#define T_SATA0_CFG_SATA 0x54c
#define T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN BIT(12)
@@ -82,9 +121,35 @@
#define T_SATA0_CHX_PHY_CTRL11 0x6d0
#define T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ (0x2800 << 16)
+#define T_SATA0_CHX_PHY_CTRL17_0 0x6e8
+#define T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1 0x55010000
+#define T_SATA0_CHX_PHY_CTRL18_0 0x6ec
+#define T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2 0x55010000
+#define T_SATA0_CHX_PHY_CTRL20_0 0x6f4
+#define T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1 0x1
+#define T_SATA0_CHX_PHY_CTRL21_0 0x6f8
+#define T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2 0x1
+
+/* AUX Registers */
+#define SATA_AUX_MISC_CNTL_1_0 0x8
+#define SATA_AUX_MISC_CNTL_1_0_DEVSLP_OVERRIDE BIT(17)
+#define SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT BIT(13)
+#define SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT BIT(15)
+
+#define SATA_AUX_RX_STAT_INT_0 0xc
+#define SATA_AUX_RX_STAT_INT_0_SATA_DEVSLP BIT(7)
+
+#define SATA_AUX_SPARE_CFG0_0 0x18
+#define SATA_AUX_SPARE_CFG0_0_MDAT_TIMER_AFTER_PG_VALID BIT(14)
+
#define FUSE_SATA_CALIB 0x124
#define FUSE_SATA_CALIB_MASK 0x3
+enum {
+ NO_DEVSLP = (1 << 0),
+ NO_DIPM = (1 << 1),
NO_DIPM can be removed now.
+};
+
struct sata_pad_calibration {
u8 gen1_tx_amp;
u8 gen1_tx_peak;
@@ -99,15 +164,91 @@ static const struct sata_pad_calibration tegra124_pad_calibration[] = {
{0x14, 0x0e, 0x1a, 0x0e},
};
+struct tegra_ahci_ops {
+ int (*init)(struct ahci_host_priv *);
+};
+
+struct tegra_ahci_soc {
+ const char *const *supply_names;
+ u32 num_supplies;
+ u32 quirks;
+ struct tegra_ahci_ops ops;
+};
+
struct tegra_ahci_priv {
struct platform_device *pdev;
void __iomem *sata_regs;
+ void __iomem *sata_aux_regs;
struct reset_control *sata_rst;
struct reset_control *sata_oob_rst;
struct reset_control *sata_cold_rst;
/* Needs special handling, cannot use ahci_platform */
struct clk *sata_clk;
- struct regulator_bulk_data supplies[5];
+ struct regulator_bulk_data *supplies;
+ struct tegra_ahci_soc *soc_data;
+};
+
+static const char *const tegra124_supply_names[] = {
+ "avdd", "hvdd", "vddio", "target-5v", "target-12v"
+};
+
+static void tegra_ahci_handle_quirks(struct ahci_host_priv *hpriv);
We should be able to move the tegra_ahci_handle_quirks function
definition here now, instead of having a declaration, I think.
+
+static int tegra124_ahci_init(struct ahci_host_priv *hpriv)
+{
+ struct tegra_ahci_priv *tegra = hpriv->plat_data;
+ struct sata_pad_calibration calib;
+ int ret;
+ u32 val;
+
+ /* Pad calibration */
+ ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val);
+ if (ret)
+ return ret;
+
+ calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK];
+
+ writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
+
+ val = readl(tegra->sata_regs +
+ SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1);
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK;
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK;
+ val |= calib.gen1_tx_amp << T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
+ val |= calib.gen1_tx_peak << T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
+ T_SATA0_CHX_PHY_CTRL1_GEN1);
+
+ val = readl(tegra->sata_regs +
+ SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2);
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK;
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK;
+ val |= calib.gen2_tx_amp << T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
+ val |= calib.gen2_tx_peak << T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
+ T_SATA0_CHX_PHY_CTRL1_GEN2);
+
+ writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ,
+ tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11);
+ writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1,
+ tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2);
+
+ writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
+
+ return 0;
+}
+
+static const struct tegra_ahci_soc tegra124_ahci_soc_data = {
+ .supply_names = tegra124_supply_names,
+ .num_supplies = ARRAY_SIZE(tegra124_supply_names),
+ .quirks = NO_DIPM | NO_DEVSLP,
also from here
+ .ops = {
+ .init = tegra124_ahci_init,
+ },
+};
+
+static const struct tegra_ahci_soc tegra210_ahci_soc_data = {
+ .quirks = NO_DIPM | NO_DEVSLP,
and here
};
static int tegra_ahci_power_on(struct ahci_host_priv *hpriv)
@@ -115,7 +256,7 @@ static int tegra_ahci_power_on(struct ahci_host_priv *hpriv)
struct tegra_ahci_priv *tegra = hpriv->plat_data;
int ret;
- ret = regulator_bulk_enable(ARRAY_SIZE(tegra->supplies),
+ ret = regulator_bulk_enable(tegra->soc_data->num_supplies,
tegra->supplies);
if (ret)
return ret;
@@ -144,8 +285,7 @@ static int tegra_ahci_power_on(struct ahci_host_priv *hpriv)
tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
disable_regulators:
- regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies);
-
+ regulator_bulk_disable(tegra->soc_data->num_supplies, tegra->supplies);
return ret;
}
@@ -162,97 +302,139 @@ static void tegra_ahci_power_off(struct ahci_host_priv *hpriv)
clk_disable_unprepare(tegra->sata_clk);
tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
- regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies);
+ regulator_bulk_disable(tegra->soc_data->num_supplies, tegra->supplies);
}
static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv)
{
struct tegra_ahci_priv *tegra = hpriv->plat_data;
int ret;
- unsigned int val;
- struct sata_pad_calibration calib;
+ u32 val;
ret = tegra_ahci_power_on(hpriv);
- if (ret) {
- dev_err(&tegra->pdev->dev,
- "failed to power on AHCI controller: %d\n", ret);
+ if (ret)
return ret;
- }
+ /*
+ * Program the following SATA IPFS registers
+ * to allow SW accesses to SATA's MMIO register range.
+ */
+ val = readl(tegra->sata_regs + SATA_FPCI_BAR5);
+ val &= ~(SATA_FPCI_BAR5_START_MASK | SATA_FPCI_BAR5_ACCESS_TYPE);
+ val |= SATA_FPCI_BAR5_START | SATA_FPCI_BAR5_ACCESS_TYPE;
+ writel(val, tegra->sata_regs + SATA_FPCI_BAR5);
+
+ /* Program the following SATA IPFS register to enable the SATA */
val = readl(tegra->sata_regs + SATA_CONFIGURATION_0);
- val |= SATA_CONFIGURATION_EN_FPCI;
+ val |= SATA_CONFIGURATION_0_EN_FPCI;
writel(val, tegra->sata_regs + SATA_CONFIGURATION_0);
- /* Pad calibration */
-
- ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val);
- if (ret) {
- dev_err(&tegra->pdev->dev,
- "failed to read calibration fuse: %d\n", ret);
- return ret;
- }
-
- calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK];
-
- writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
-
- val = readl(tegra->sata_regs +
- SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1);
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK;
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK;
- val |= calib.gen1_tx_amp <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
- val |= calib.gen1_tx_peak <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
- writel(val, tegra->sata_regs + SCFG_OFFSET +
- T_SATA0_CHX_PHY_CTRL1_GEN1);
-
- val = readl(tegra->sata_regs +
- SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2);
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK;
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK;
- val |= calib.gen2_tx_amp <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
- val |= calib.gen2_tx_peak <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
- writel(val, tegra->sata_regs + SCFG_OFFSET +
- T_SATA0_CHX_PHY_CTRL1_GEN2);
-
- writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ,
- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11);
- writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1,
- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2);
-
- writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
-
- /* Program controller device ID */
+ /* Electrical settings for better link stability */
+ val = T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL17_0);
+ val = T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL18_0);
+ val = T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL20_0);
+ val = T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL21_0);
+
+ /* For SQUELCH Filter & Gen3 drive getting detected as Gen1 drive */
+
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0);
+ val |= T_SATA_CFG_PHY_0_MASK_SQUELCH;
+ val &= ~T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0);
+
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB);
+ val &= ~(T_SATA0_NVOOB_COMMA_CNT_MASK |
+ T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK |
+ T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK);
+ val |= (T_SATA0_NVOOB_COMMA_CNT |
+ T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH |
+ T_SATA0_NVOOB_SQUELCH_FILTER_MODE);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB);
+
+ /*
+ * Change CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW from 83.3 ns to 58.8ns
+ */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2);
+ val &= ~T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK;
+ val |= T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2);
+
+ if (tegra->soc_data->ops.init)
+ tegra->soc_data->ops.init(hpriv);
+
+ /*
+ * Program the following SATA configuration registers
+ * to initialize SATA
+ */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
+ val |= (T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE |
+ T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
+ val = T_SATA0_CFG_9_BASE_ADDRESS;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9);
+ /* Program Class Code and Programming interface for SATA */
val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
val |= T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN;
writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
- writel(0x01060100, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC);
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC);
+ val &=
+ ~(T_SATA0_BKDOOR_CC_CLASS_CODE_MASK |
+ T_SATA0_BKDOOR_CC_PROG_IF_MASK);
+ val |= T_SATA0_BKDOOR_CC_CLASS_CODE | T_SATA0_BKDOOR_CC_PROG_IF;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC);
val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
val &= ~T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN;
writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
- /* Enable IO & memory access, bus master mode */
-
- val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
- val |= T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE |
- T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR;
- writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
-
- /* Program SATA MMIO */
-
- writel(0x10000 << SATA_FPCI_BAR5_START_SHIFT,
- tegra->sata_regs + SATA_FPCI_BAR5);
+ /* Enabling LPM capabilities through Backdoor Programming */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_HBA_CAP_BKDR);
+ val |= (T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP |
+ T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP |
+ T_SATA0_AHCI_HBA_CAP_BKDR_SALP |
+ T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_HBA_CAP_BKDR);
+
+ /* SATA Second Level Clock Gating configuration
+ * Enabling Gating of Tx/Rx clocks and driving Pad IDDQ and Lane
+ * IDDQ Signals
+ */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35);
+ val &= ~T_SATA0_CFG_35_IDP_INDEX_MASK;
+ val |= T_SATA0_CFG_35_IDP_INDEX;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35);
+
+ val = T_SATA0_AHCI_IDP1_DATA;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_IDP1);
+
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1);
+ val |= (T_SATA0_CFG_PHY_1_PADS_IDDQ_EN |
+ T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1);
+
+ /*
+ * Indicate Sata only has the capability to enter DevSleep
+ * from slumber link.
+ */
+
+ if (tegra->sata_aux_regs) {
+ val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ val |= SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT;
+ writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ }
- writel(0x08000 << T_SATA0_CFG_9_BASE_ADDRESS_SHIFT,
- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9);
+ /* Enabling IPFS Clock Gating */
+ val = readl(tegra->sata_regs + SATA_CONFIGURATION_0);
+ val &= ~SATA_CONFIGURATION_0_CLK_OVERRIDE;
+ writel(val, tegra->sata_regs + SATA_CONFIGURATION_0);
- /* Unmask SATA interrupts */
+ tegra_ahci_handle_quirks(hpriv);
val = readl(tegra->sata_regs + SATA_INTR_MASK);
val |= SATA_INTR_MASK_IP_INT_MASK;
@@ -278,15 +460,22 @@ static struct ata_port_operations ahci_tegra_port_ops = {
.host_stop = tegra_ahci_host_stop,
};
-static const struct ata_port_info ahci_tegra_port_info = {
- .flags = AHCI_FLAG_COMMON,
+static struct ata_port_info ahci_tegra_port_info = {
This can be const now
+ .flags = AHCI_FLAG_COMMON | ATA_FLAG_NO_DIPM,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
.port_ops = &ahci_tegra_port_ops,
};
static const struct of_device_id tegra_ahci_of_match[] = {
- { .compatible = "nvidia,tegra124-ahci" },
+ {
+ .compatible = "nvidia,tegra124-ahci",
+ .data = &tegra124_ahci_soc_data
+ },
+ {
+ .compatible = "nvidia,tegra210-ahci",
+ .data = &tegra210_ahci_soc_data
+ },
{}
};
MODULE_DEVICE_TABLE(of, tegra_ahci_of_match);
@@ -295,12 +484,25 @@ static struct scsi_host_template ahci_platform_sht = {
AHCI_SHT(DRV_NAME),
};
+static void tegra_ahci_handle_quirks(struct ahci_host_priv *hpriv)
+{
+ struct tegra_ahci_priv *tegra = hpriv->plat_data;
+ u32 val;
+
+ if (tegra->sata_aux_regs && (tegra->soc_data->quirks & NO_DEVSLP)) {
+ val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ val &= ~SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT;
+ writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ }
+}
+
static int tegra_ahci_probe(struct platform_device *pdev)
{
struct ahci_host_priv *hpriv;
struct tegra_ahci_priv *tegra;
struct resource *res;
int ret;
+ unsigned int i;
hpriv = ahci_platform_get_resources(pdev);
if (IS_ERR(hpriv))
@@ -311,13 +513,25 @@ static int tegra_ahci_probe(struct platform_device *pdev)
return -ENOMEM;
hpriv->plat_data = tegra;
-
tegra->pdev = pdev;
+ tegra->soc_data =
+ (struct tegra_ahci_soc *)of_device_get_match_data(&pdev->dev);
res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
tegra->sata_regs = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(tegra->sata_regs))
return PTR_ERR(tegra->sata_regs);
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ /*
+ * Aux register is optional.
+ */
+ if (res) {
+ tegra->sata_aux_regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(tegra->sata_aux_regs))
+ return PTR_ERR(tegra->sata_aux_regs);
+ } else {
+ tegra->sata_aux_regs = NULL;
+ }
'tegra' is allocated using kzalloc, so the else branch is not required
tegra->sata_rst = devm_reset_control_get(&pdev->dev, "sata");
if (IS_ERR(tegra->sata_rst)) {
@@ -343,13 +557,17 @@ static int tegra_ahci_probe(struct platform_device *pdev)
return PTR_ERR(tegra->sata_clk);
}
- tegra->supplies[0].supply = "avdd";
- tegra->supplies[1].supply = "hvdd";
- tegra->supplies[2].supply = "vddio";
- tegra->supplies[3].supply = "target-5v";
- tegra->supplies[4].supply = "target-12v";
+ tegra->supplies = devm_kcalloc(&pdev->dev,
+ tegra->soc_data->num_supplies,
+ sizeof(*tegra->supplies), GFP_KERNEL);
+ if (!tegra->supplies)
+ return -ENOMEM;
+
+ for (i = 0; i < tegra->soc_data->num_supplies; i++)
+ tegra->supplies[i].supply = tegra->soc_data->supply_names[i];
- ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(tegra->supplies),
+ ret = devm_regulator_bulk_get(&pdev->dev,
+ tegra->soc_data->num_supplies,
tegra->supplies);
if (ret) {
dev_err(&pdev->dev, "Failed to get regulators\n");
@@ -385,5 +603,5 @@ static struct platform_driver tegra_ahci_driver = {
module_platform_driver(tegra_ahci_driver);
MODULE_AUTHOR("Mikko Perttunen <mperttunen@xxxxxxxxxx>");
-MODULE_DESCRIPTION("Tegra124 AHCI SATA driver");
+MODULE_DESCRIPTION("Tegra AHCI SATA driver");
MODULE_LICENSE("GPL v2");
Thanks,
Mikko
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html