From: Preetham Chandru R <pchandru@xxxxxxxxxx>
1. Move tegra124 specifics to tegra124_ahci_init.
2. Separate the regulators needed for tegra124 and tegra210.
3. Disable DIPM and Devslp for t210 and t124 as there are known issues
Signed-off-by: Preetham Chandru R <pchandru@xxxxxxxxxx>
---
v3:
* Remove inline functions for read/write and modify to
SATA, SATA Config and SATA Aux registers.
* Add code to disable DIPM and DevSlp for t210 and t124
v2:
* Fix indentation issues
* Move the change to disable DIPM, HIPM, DevSlp, partial,
slumber and NCQ into a separate patch
---
drivers/ata/ahci_tegra.c | 377 ++++++++++++++++++++++++++++++++++++-----------
1 file changed, 293 insertions(+), 84 deletions(-)
diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c
index 3a62eb2..cd581a6 100644
--- a/drivers/ata/ahci_tegra.c
+++ b/drivers/ata/ahci_tegra.c
@@ -34,7 +34,8 @@
#define DRV_NAME "tegra-ahci"
#define SATA_CONFIGURATION_0 0x180
-#define SATA_CONFIGURATION_EN_FPCI BIT(0)
+#define SATA_CONFIGURATION_0_EN_FPCI BIT(0)
+#define SATA_CONFIGURATION_0_CLK_OVERRIDE BIT(31)
#define SCFG_OFFSET 0x1000
@@ -45,17 +46,55 @@
#define T_SATA0_CFG_1_SERR BIT(8)
#define T_SATA0_CFG_9 0x24
-#define T_SATA0_CFG_9_BASE_ADDRESS_SHIFT 13
+#define T_SATA0_CFG_9_BASE_ADDRESS 0x40020000
#define SATA_FPCI_BAR5 0x94
-#define SATA_FPCI_BAR5_START_SHIFT 4
+#define SATA_FPCI_BAR5_START_MASK (0xfffffff << 4)
+#define SATA_FPCI_BAR5_START (0x0040020 << 4)
+#define SATA_FPCI_BAR5_ACCESS_TYPE (0x1)
#define SATA_INTR_MASK 0x188
#define SATA_INTR_MASK_IP_INT_MASK BIT(16)
+#define T_SATA0_CFG_35 0x94
+#define T_SATA0_CFG_35_IDP_INDEX_MASK (0x7ff << 2)
+#define T_SATA0_CFG_35_IDP_INDEX (0x2a << 2)
+
+#define T_SATA0_AHCI_IDP1 0x98
+#define T_SATA0_AHCI_IDP1_DATA (0x400040)
+
+#define T_SATA0_CFG_PHY_1 0x12c
+#define T_SATA0_CFG_PHY_1_PADS_IDDQ_EN BIT(23)
+#define T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN BIT(22)
+
+#define T_SATA0_NVOOB 0x114
+#define T_SATA0_NVOOB_COMMA_CNT_MASK (0xff << 16)
+#define T_SATA0_NVOOB_COMMA_CNT (0x07 << 16)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK (0x3 << 24)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE (0x1 << 24)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK (0x3 << 26)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH (0x3 << 26)
+
+#define T_SATA_CFG_PHY_0 0x120
+#define T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD BIT(11)
+#define T_SATA_CFG_PHY_0_MASK_SQUELCH BIT(24)
+
+#define T_SATA0_CFG2NVOOB_2 0x134
+#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK (0x1ff << 18)
+#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW (0xc << 18)
+
#define T_SATA0_AHCI_HBA_CAP_BKDR 0x300
+#define T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP BIT(13)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP BIT(14)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SALP BIT(26)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM BIT(17)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SNCQ BIT(30)
#define T_SATA0_BKDOOR_CC 0x4a4
+#define T_SATA0_BKDOOR_CC_CLASS_CODE_MASK (0xffff << 16)
+#define T_SATA0_BKDOOR_CC_CLASS_CODE (0x0106 << 16)
+#define T_SATA0_BKDOOR_CC_PROG_IF_MASK (0xff << 8)
+#define T_SATA0_BKDOOR_CC_PROG_IF (0x01 << 8)
#define T_SATA0_CFG_SATA 0x54c
#define T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN BIT(12)
@@ -82,9 +121,35 @@
#define T_SATA0_CHX_PHY_CTRL11 0x6d0
#define T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ (0x2800 << 16)
+#define T_SATA0_CHX_PHY_CTRL17_0 0x6e8
+#define T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1 0x55010000
+#define T_SATA0_CHX_PHY_CTRL18_0 0x6ec
+#define T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2 0x55010000
+#define T_SATA0_CHX_PHY_CTRL20_0 0x6f4
+#define T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1 0x1
+#define T_SATA0_CHX_PHY_CTRL21_0 0x6f8
+#define T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2 0x1
+
+/* AUX Registers */
+#define SATA_AUX_MISC_CNTL_1_0 0x8
+#define SATA_AUX_MISC_CNTL_1_0_DEVSLP_OVERRIDE BIT(17)
+#define SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT BIT(13)
+#define SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT BIT(15)
+
+#define SATA_AUX_RX_STAT_INT_0 0xc
+#define SATA_AUX_RX_STAT_INT_0_SATA_DEVSLP BIT(7)
+
+#define SATA_AUX_SPARE_CFG0_0 0x18
+#define SATA_AUX_SPARE_CFG0_0_MDAT_TIMER_AFTER_PG_VALID BIT(14)
+
#define FUSE_SATA_CALIB 0x124
#define FUSE_SATA_CALIB_MASK 0x3
+enum {
+ NO_DEVSLP = (1 << 0),
+ NO_DIPM = (1 << 1),
+};
+
struct sata_pad_calibration {
u8 gen1_tx_amp;
u8 gen1_tx_peak;
@@ -99,15 +164,89 @@ static const struct sata_pad_calibration tegra124_pad_calibration[] = {
{0x14, 0x0e, 0x1a, 0x0e},
};
+struct tegra_ahci_ops {
+ int (*init)(struct ahci_host_priv *);
+};
+
+struct tegra_ahci_soc {
+ const char *const *supply_names;
+ u32 num_supplies;
+ u32 quirks;
+ struct tegra_ahci_ops ops;
+};
+
struct tegra_ahci_priv {
struct platform_device *pdev;
void __iomem *sata_regs;
+ void __iomem *sata_aux_regs;
struct reset_control *sata_rst;
struct reset_control *sata_oob_rst;
struct reset_control *sata_cold_rst;
/* Needs special handling, cannot use ahci_platform */
struct clk *sata_clk;
- struct regulator_bulk_data supplies[5];
+ struct regulator_bulk_data *supplies;
+ struct tegra_ahci_soc *soc_data;
+};
+
+static const char *const tegra124_supply_names[] = {
+ "avdd", "hvdd", "vddio", "target-5v", "target-12v"
+};
+
+static int tegra124_ahci_init(struct ahci_host_priv *hpriv)
+{
+ struct tegra_ahci_priv *tegra = hpriv->plat_data;
+ struct sata_pad_calibration calib;
+ int ret;
+ u32 val;
+
+ /* Pad calibration */
+ ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val);
+ if (ret)
+ return ret;
+
+ calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK];
+
+ writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
+
+ val = readl(tegra->sata_regs +
+ SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1);
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK;
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK;
+ val |= calib.gen1_tx_amp << T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
+ val |= calib.gen1_tx_peak << T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
+ T_SATA0_CHX_PHY_CTRL1_GEN1);
+
+ val = readl(tegra->sata_regs +
+ SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2);
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK;
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK;
+ val |= calib.gen2_tx_amp << T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
+ val |= calib.gen2_tx_peak << T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
+ T_SATA0_CHX_PHY_CTRL1_GEN2);
+
+ writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ,
+ tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11);
+ writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1,
+ tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2);
+
+ writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
+
+ return 0;
+}
+
+static const struct tegra_ahci_soc tegra124_ahci_soc_data = {
+ .supply_names = tegra124_supply_names,
+ .num_supplies = ARRAY_SIZE(tegra124_supply_names),
+ .quirks = NO_DIPM | NO_DEVSLP,
+ .ops = {
+ .init = tegra124_ahci_init,
+ },
+};
+
+static const struct tegra_ahci_soc tegra210_ahci_soc_data = {
+ .quirks = NO_DIPM | NO_DEVSLP,
};
static int tegra_ahci_power_on(struct ahci_host_priv *hpriv)
@@ -115,7 +254,7 @@ static int tegra_ahci_power_on(struct ahci_host_priv *hpriv)
struct tegra_ahci_priv *tegra = hpriv->plat_data;
int ret;
- ret = regulator_bulk_enable(ARRAY_SIZE(tegra->supplies),
+ ret = regulator_bulk_enable(tegra->soc_data->num_supplies,
tegra->supplies);
if (ret)
return ret;
@@ -144,8 +283,7 @@ static int tegra_ahci_power_on(struct ahci_host_priv *hpriv)
tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
disable_regulators:
- regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies);
-
+ regulator_bulk_disable(tegra->soc_data->num_supplies, tegra->supplies);
return ret;
}
@@ -162,97 +300,137 @@ static void tegra_ahci_power_off(struct ahci_host_priv *hpriv)
clk_disable_unprepare(tegra->sata_clk);
tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
- regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies);
+ regulator_bulk_disable(tegra->soc_data->num_supplies, tegra->supplies);
}
static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv)
{
struct tegra_ahci_priv *tegra = hpriv->plat_data;
int ret;
- unsigned int val;
- struct sata_pad_calibration calib;
+ u32 val;
ret = tegra_ahci_power_on(hpriv);
- if (ret) {
- dev_err(&tegra->pdev->dev,
- "failed to power on AHCI controller: %d\n", ret);
+ if (ret)
return ret;
- }
+ /*
+ * Program the following SATA IPFS registers
+ * to allow SW accesses to SATA's MMIO Register
+ */
+ val = readl(tegra->sata_regs + SATA_FPCI_BAR5);
+ val &= ~(SATA_FPCI_BAR5_START_MASK | SATA_FPCI_BAR5_ACCESS_TYPE);
+ val |= SATA_FPCI_BAR5_START | SATA_FPCI_BAR5_ACCESS_TYPE;
+ writel(val, tegra->sata_regs + SATA_FPCI_BAR5);
+
+ /* Program the following SATA IPFS register to enable the SATA */
val = readl(tegra->sata_regs + SATA_CONFIGURATION_0);
- val |= SATA_CONFIGURATION_EN_FPCI;
+ val |= SATA_CONFIGURATION_0_EN_FPCI;
writel(val, tegra->sata_regs + SATA_CONFIGURATION_0);
- /* Pad calibration */
-
- ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val);
- if (ret) {
- dev_err(&tegra->pdev->dev,
- "failed to read calibration fuse: %d\n", ret);
- return ret;
- }
-
- calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK];
-
- writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
-
- val = readl(tegra->sata_regs +
- SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1);
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK;
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK;
- val |= calib.gen1_tx_amp <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
- val |= calib.gen1_tx_peak <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
- writel(val, tegra->sata_regs + SCFG_OFFSET +
- T_SATA0_CHX_PHY_CTRL1_GEN1);
-
- val = readl(tegra->sata_regs +
- SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2);
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK;
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK;
- val |= calib.gen2_tx_amp <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
- val |= calib.gen2_tx_peak <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
- writel(val, tegra->sata_regs + SCFG_OFFSET +
- T_SATA0_CHX_PHY_CTRL1_GEN2);
-
- writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ,
- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11);
- writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1,
- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2);
-
- writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
-
- /* Program controller device ID */
+ /* Electrical settings for better link stability */
+ val = T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL17_0);
+ val = T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL18_0);
+ val = T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL20_0);
+ val = T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL21_0);
+
+ /* For SQUELCH Filter & Gen3 drive getting detected as Gen1 drive */
+
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0);
+ val |= T_SATA_CFG_PHY_0_MASK_SQUELCH;
+ val &= ~T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0);
+
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB);
+ val &= ~(T_SATA0_NVOOB_COMMA_CNT_MASK |
+ T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK |
+ T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK);
+ val |= (T_SATA0_NVOOB_COMMA_CNT |
+ T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH |
+ T_SATA0_NVOOB_SQUELCH_FILTER_MODE);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB);
+
+ /*
+ * Change CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW from 83.3 ns to 58.8ns
+ */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2);
+ val &= ~T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK;
+ val |= T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2);
+
+ if (tegra->soc_data->ops.init)
+ tegra->soc_data->ops.init(hpriv);
+
+ /*
+ * Program the following SATA configuration registers
+ * to initialize SATA
+ */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
+ val |= (T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE |
+ T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
+ val = T_SATA0_CFG_9_BASE_ADDRESS;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9);
+ /* Program Class Code and Programming interface for SATA */
val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
val |= T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN;
writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
- writel(0x01060100, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC);
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC);
+ val &=
+ ~(T_SATA0_BKDOOR_CC_CLASS_CODE_MASK |
+ T_SATA0_BKDOOR_CC_PROG_IF_MASK);
+ val |= T_SATA0_BKDOOR_CC_CLASS_CODE | T_SATA0_BKDOOR_CC_PROG_IF;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC);
val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
val &= ~T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN;
writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
- /* Enable IO & memory access, bus master mode */
-
- val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
- val |= T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE |
- T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR;
- writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
-
- /* Program SATA MMIO */
-
- writel(0x10000 << SATA_FPCI_BAR5_START_SHIFT,
- tegra->sata_regs + SATA_FPCI_BAR5);
-
- writel(0x08000 << T_SATA0_CFG_9_BASE_ADDRESS_SHIFT,
- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9);
+ /* Enabling LPM capabilities through Backdoor Programming */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_HBA_CAP_BKDR);
+ val |= (T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP |
+ T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP |
+ T_SATA0_AHCI_HBA_CAP_BKDR_SALP |
+ T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_HBA_CAP_BKDR);
+
+ /* SATA Second Level Clock Gating configuration
+ * Enabling Gating of Tx/Rx clocks and driving Pad IDDQ and Lane
+ * IDDQ Signals
+ */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35);
+ val &= ~T_SATA0_CFG_35_IDP_INDEX_MASK;
+ val |= T_SATA0_CFG_35_IDP_INDEX;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35);
+
+ val = T_SATA0_AHCI_IDP1_DATA;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_IDP1);
+
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1);
+ val |= (T_SATA0_CFG_PHY_1_PADS_IDDQ_EN |
+ T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1);
+
+ /*
+ * Indicate Sata only has the capability to enter DevSleep
+ * from slumber link.
+ */
+
+ val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ val |= SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT;
+ writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+
+ /* Enabling IPFS Clock Gating */
+ val = readl(tegra->sata_regs + SATA_CONFIGURATION_0);
+ val &= ~SATA_CONFIGURATION_0_CLK_OVERRIDE;
+ writel(val, tegra->sata_regs + SATA_CONFIGURATION_0);
- /* Unmask SATA interrupts */
+ tegra_ahci_handle_quirks(hpriv);
val = readl(tegra->sata_regs + SATA_INTR_MASK);
val |= SATA_INTR_MASK_IP_INT_MASK;
@@ -278,7 +456,7 @@ static struct ata_port_operations ahci_tegra_port_ops = {
.host_stop = tegra_ahci_host_stop,
};
-static const struct ata_port_info ahci_tegra_port_info = {
+static struct ata_port_info ahci_tegra_port_info = {
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
@@ -286,7 +464,14 @@ static const struct ata_port_info ahci_tegra_port_info = {
};
static const struct of_device_id tegra_ahci_of_match[] = {
- { .compatible = "nvidia,tegra124-ahci" },
+ {
+ .compatible = "nvidia,tegra124-ahci",
+ .data = &tegra124_ahci_soc_data
+ },
+ {
+ .compatible = "nvidia,tegra210-ahci",
+ .data = &tegra210_ahci_soc_data
+ },
{}
};
MODULE_DEVICE_TABLE(of, tegra_ahci_of_match);
@@ -295,12 +480,27 @@ static struct scsi_host_template ahci_platform_sht = {
AHCI_SHT(DRV_NAME),
};
+static void tegra_ahci_handle_quirks(struct ahci_host_priv *hpriv)
+{
+ struct tegra_ahci_priv *tegra = hpriv->plat_data;
+ u32 val;
+
+ if (tegra->soc_data->quirks & NO_DEVSLP) {
+ val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ val &= ~SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT;
+ writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ } else if (tegra->soc_data->quirks & NO_DIPM) {
+ ahci_tegra_port_info.flags |= ATA_FLAG_NO_DIPM;
+ }
+}
+
static int tegra_ahci_probe(struct platform_device *pdev)
{
struct ahci_host_priv *hpriv;
struct tegra_ahci_priv *tegra;
struct resource *res;
int ret;
+ unsigned int i;
hpriv = ahci_platform_get_resources(pdev);
if (IS_ERR(hpriv))
@@ -311,13 +511,18 @@ static int tegra_ahci_probe(struct platform_device *pdev)
return -ENOMEM;
hpriv->plat_data = tegra;
-
tegra->pdev = pdev;
+ tegra->soc_data =
+ (struct tegra_ahci_soc *)of_device_get_match_data(&pdev->dev);
res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
tegra->sata_regs = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(tegra->sata_regs))
return PTR_ERR(tegra->sata_regs);
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ tegra->sata_aux_regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(tegra->sata_aux_regs))
+ return PTR_ERR(tegra->sata_aux_regs);
tegra->sata_rst = devm_reset_control_get(&pdev->dev, "sata");
if (IS_ERR(tegra->sata_rst)) {
@@ -343,13 +548,17 @@ static int tegra_ahci_probe(struct platform_device *pdev)
return PTR_ERR(tegra->sata_clk);
}
- tegra->supplies[0].supply = "avdd";
- tegra->supplies[1].supply = "hvdd";
- tegra->supplies[2].supply = "vddio";
- tegra->supplies[3].supply = "target-5v";
- tegra->supplies[4].supply = "target-12v";
+ tegra->supplies = devm_kcalloc(&pdev->dev,
+ tegra->soc_data->num_supplies,
+ sizeof(*tegra->supplies), GFP_KERNEL);
+ if (!tegra->supplies)
+ return -ENOMEM;
+
+ for (i = 0; i < tegra->soc_data->num_supplies; i++)
+ tegra->supplies[i].supply = tegra->soc_data->supply_names[i];
- ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(tegra->supplies),
+ ret = devm_regulator_bulk_get(&pdev->dev,
+ tegra->soc_data->num_supplies,
tegra->supplies);
if (ret) {
dev_err(&pdev->dev, "Failed to get regulators\n");
@@ -385,5 +594,5 @@ static struct platform_driver tegra_ahci_driver = {
module_platform_driver(tegra_ahci_driver);
MODULE_AUTHOR("Mikko Perttunen <mperttunen@xxxxxxxxxx>");
-MODULE_DESCRIPTION("Tegra124 AHCI SATA driver");
+MODULE_DESCRIPTION("Tegra AHCI SATA driver");
MODULE_LICENSE("GPL v2");
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
