A SATA PCI-controller card using the kernel module sata_sil24 has problems
transferring big files.
First of all a description of the situation:
-- Hardware:
- mainboard Gigabyte GA-MA69GM-S2H; chipset AMD 690G / SB600; 2 PCI slots
(32 bit); 1 PCIe 4x slot; 1 PCIe 16 x slot; 8 GiB RAM; AMD Phenom(tm) II X4
955 Processor
- SATA controller card Dawicontrol DC-3410 RAID, 32 bit PCI; chipset
SiI3124ACBHU; BIOS message: running at 32 bit / 33 MHz
- with hard disks: HDS721616PLA380 (twice), ST3000DM001-9YN166 (temporary)
- q.v. attachment lspci; (dmidecode (v 3.0) finds no SMBIOS nor DMI entry
point)
-- [Debian] System Information:
Debian Release: stretch/sid
APT prefers unstable
APT policy: (998, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 4.9.2 (SMP w/4 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-source-4.9 depends on:
ii binutils 2.27.90.20170113-1
ii xz-utils 5.2.2-1.2
Versions of packages linux-source-4.9 recommends:
ii bc 1.06.95-9+b2
ii gcc 4:6.2.1-1
ii libc6-dev [libc-dev] 2.24-8
ii make 4.1-9
Versions of packages linux-source-4.9 suggests:
ii libncurses5-dev [ncurses-dev] 6.0+20161126-1
pn libqt4-dev <none>
pn pkg-config <none>
1st test setting:
Reading from the disks to /dev/null with
dd if=/dev/sde of=/dev/null bs=4k count=2304k
one after the other. (Disk ST3000DM001 was temporarily directly connected to
the card's external SATA port.)
Result: After some MB, but before 470 MiB errors occurred:
failed command: READ FPDMA QUEUED
[cf. attachment dmesg]
failed command: READ DMA
[cf. attachment dmesg_tmpHD]
The errors were reproducible - however, they started after different amounts
of data.
2nd test setting:
Using Debian's kernel and patching the driver to not use 64 bit DMA [cf.
attachment sata_sil24.c.diff].
Doing the same tests as above.
Result: Repeatedly no errors occurred.
N.B.: 1) There is a Windows Vista (32 bit) installation that uses two of the
ports of the controller card as a fake RAID 1: There are no problems with the
internal directly connected drives nor with an external drive.
2) Prior to this controller card there was a PCI Express card using SiI 3132,
that - if I remember rightly - also had such problems, but they started after
a greater amount of data. (At that time a Windows XP x64 installation had no
problems, too.)
If you need or want additional information or tests, let me know.
Matthias
00:00.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD/ATI] RS690 Host Bridge [1002:7910]
Subsystem: Gigabyte Technology Co., Ltd RS690 Host Bridge [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
NUMA node: 0
00:02.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] RS690 PCI to PCI Bridge (PCI Express Graphics Port 0) [1002:7913] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 24
NUMA node: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag+ RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #2, PowerLimit 75.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
RootCap: CRSVisible+
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 41b1
Capabilities: [b0] Subsystem: Gigabyte Technology Co., Ltd RS690 PCI to PCI Bridge (PCI Express Graphics Port 0) [1458:5000]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:04.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] Device [1002:7914] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 25
NUMA node: 0
Bus: primary=00, secondary=02, subordinate=05, sec-latency=0
I/O behind bridge: 0000d000-0000efff
Memory behind bridge: fdb00000-fdcfffff
Prefetchable memory behind bridge: 00000000fde00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag+ RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #4, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
RootCap: CRSVisible+
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 41c1
Capabilities: [b0] Subsystem: Gigabyte Technology Co., Ltd Device [1458:5000]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pcieport
Kernel modules: shpchp
00:12.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 Non-Raid-5 SATA [1002:4380] (prog-if 01 [AHCI 1.0])
Subsystem: Gigabyte Technology Co., Ltd Gigabyte GA-MA69G-S3H Motherboard [1458:b005]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 22
NUMA node: 0
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ahci
Kernel modules: ahci
00:13.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI0) [1002:4387] (prog-if 10 [OHCI])
Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI0) [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
NUMA node: 0
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:13.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI1) [1002:4388] (prog-if 10 [OHCI])
Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI1) [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
NUMA node: 0
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:13.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI2) [1002:4389] (prog-if 10 [OHCI])
Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI2) [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
NUMA node: 0
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:13.3 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI3) [1002:438a] (prog-if 10 [OHCI])
Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI3) [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
NUMA node: 0
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:13.4 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB (OHCI4) [1002:438b] (prog-if 10 [OHCI])
Subsystem: Gigabyte Technology Co., Ltd SB600 USB (OHCI4) [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
NUMA node: 0
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:13.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 USB Controller (EHCI) [1002:4386] (prog-if 20 [EHCI])
Subsystem: Gigabyte Technology Co., Ltd SB600 USB Controller (EHCI) [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin D routed to IRQ 19
NUMA node: 0
Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:14.0 SMBus [0c05]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller [1002:4385] (rev 14)
Subsystem: Gigabyte Technology Co., Ltd GA-MA770-DS3rev2.0 Motherboard [1458:4385]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
NUMA node: 0
Region 0: I/O ports at 0b00 [size=16]
Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: piix4_smbus
Kernel modules: i2c_piix4, sp5100_tco
00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 IDE [1002:438c] (prog-if 8a [Master SecP PriP])
Subsystem: Gigabyte Technology Co., Ltd Gigabyte GA-MA69G-S3H Motherboard [1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 16
NUMA node: 0
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at f900 [size=16]
Kernel driver in use: pata_atiixp
Kernel modules: pata_atiixp, ata_generic
00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) [1002:4383]
Subsystem: Gigabyte Technology Co., Ltd GA-MA770-DS3rev2.0 Motherboard [1458:a022]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
NUMA node: 0
Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:14.3 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD/ATI] SB600 PCI to LPC Bridge [1002:438d]
Subsystem: Gigabyte Technology Co., Ltd SB600 PCI to LPC Bridge [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
NUMA node: 0
00:14.4 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
NUMA node: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fda00000-fdafffff
Prefetchable memory behind bridge: fd900000-fd9fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
NUMA node: 0
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: 1.0GHz
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
NUMA node: 0
00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
NUMA node: 0
00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
NUMA node: 0
Capabilities: [f0] Secure device <?>
Kernel driver in use: k10temp
Kernel modules: k10temp
00:18.4 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
NUMA node: 0
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Cape Verde LE [Radeon HD 7730/8730] [1002:6837] (prog-if 00 [VGA controller])
Subsystem: Hightech Information System Ltd. Cape Verde LE [Radeon HD 7730/8730] [1787:2330]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 34
NUMA node: 0
Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fdd80000 (64-bit, non-prefetchable) [size=256K]
Region 4: I/O ports at ce00 [size=256]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [48] Vendor Specific Information: Len=08 <?>
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4143
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [150 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [270 v1] #19
Kernel driver in use: radeon
Kernel modules: radeon
01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Cape Verde/Pitcairn HDMI Audio [Radeon HD 7700/7800 Series] [1002:aab0]
Subsystem: Hightech Information System Ltd. Cape Verde/Pitcairn HDMI Audio [Radeon HD 7700/7800 Series] [1787:aab0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 4
NUMA node: 0
Region 0: Memory at fddfc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [48] Vendor Specific Information: Len=08 <?>
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 8GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [150 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel modules: snd_hda_intel
02:00.0 PCI bridge [0604]: Pericom Semiconductor Device [12d8:2304] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
NUMA node: 0
Bus: primary=02, secondary=03, subordinate=05, sec-latency=0
I/O behind bridge: 0000d000-0000efff
Memory behind bridge: fdb00000-fdcfffff
Prefetchable memory behind bridge: 00000000fde00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [5c] Vital Product Data
Not readable
Capabilities: [64] Vendor Specific Information: Len=34 <?>
Capabilities: [b0] Subsystem: Device [0000:0000]
Capabilities: [c0] Express (v2) Upstream Port, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x2, ASPM not supported, Exit Latency L0s <512ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Via message
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=4
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=04 MaxTimeSlots=64 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128+ TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Port Arbitration Table <?>
Capabilities: [20c v1] Power Budgeting <?>
Capabilities: [230 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Kernel driver in use: pcieport
Kernel modules: shpchp
03:01.0 PCI bridge [0604]: Pericom Semiconductor Device [12d8:2304] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 26
NUMA node: 0
Bus: primary=03, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [4c] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 41d1
Capabilities: [64] Vendor Specific Information: Len=34 <?>
Capabilities: [b0] Subsystem: Device [0000:0000]
Capabilities: [c0] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s <512ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp-
LnkCtl: ASPM Disabled; Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Via message ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=4
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=04 MaxTimeSlots=64 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128+ TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Port Arbitration Table <?>
Capabilities: [20c v1] Power Budgeting <?>
Capabilities: [220 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl+ DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
Kernel modules: shpchp
03:02.0 PCI bridge [0604]: Pericom Semiconductor Device [12d8:2304] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 27
NUMA node: 0
Bus: primary=03, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [4c] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 41e1
Capabilities: [64] Vendor Specific Information: Len=34 <?>
Capabilities: [b0] Subsystem: Device [0000:0000]
Capabilities: [c0] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM not supported, Exit Latency L0s <512ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp-
LnkCtl: ASPM Disabled; Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, OBFF Via message ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=4
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=04 MaxTimeSlots=64 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128+ TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Port Arbitration Table <?>
Capabilities: [20c v1] Power Budgeting <?>
Capabilities: [220 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl+ DirectTrans+
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
Kernel modules: shpchp
04:00.0 USB controller [0c03]: Fresco Logic FL1100 USB 3.0 Host Controller [1b73:1100] (rev 10) (prog-if 30 [XHCI])
Subsystem: Sonnet Technologies, Inc. FL1100 USB 3.0 Host Controller [16b8:6e02]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 17
NUMA node: 0
Region 0: Memory at fdce0000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fdcff000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fdcfe000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [b0] MSI-X: Enable+ Count=8 Masked-
Vector table: BAR=2 offset=00000000
PBA: BAR=4 offset=00000000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
05:00.0 FireWire (IEEE 1394) [0c00]: LSI Corporation FW643 [TrueFire] PCIe 1394b Controller [11c1:5901] (rev 08) (prog-if 10 [OHCI])
Subsystem: Sonnet Technologies, Inc. FW643 [TrueFire] PCIe 1394b Controller [16b8:6e11]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 28
NUMA node: 0
Region 0: Memory at fdbff000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [4c] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4182
Capabilities: [60] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 2048 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM not supported, Exit Latency L0s <512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [170 v1] Device Serial Number 00-30-93-00-00-00-01-c3
Kernel driver in use: firewire_ohci
Kernel modules: firewire_ohci
06:06.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller [1095:3124] (rev 02)
Subsystem: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller [1095:7124]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 128, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 20
NUMA node: 0
Region 0: Memory at fdaff000 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at fdaf0000 (64-bit, non-prefetchable) [size=32K]
Region 4: I/O ports at bf00 [size=16]
[virtual] Expansion ROM at fd900000 [disabled] [size=512K]
Capabilities: [64] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=12
Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz-
Capabilities: [54] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Kernel driver in use: sata_sil24
Kernel modules: sata_sil24
06:07.0 Multimedia audio controller [0401]: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller [1412:1712] (rev 02)
Subsystem: TERRATEC Electronic GmbH DMX 6fire 24/96 [153b:1138]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 21
NUMA node: 0
Region 0: I/O ports at be00 [size=32]
Region 1: I/O ports at bd00 [size=16]
Region 2: I/O ports at bc00 [size=16]
Region 3: I/O ports at bb00 [size=64]
Capabilities: [80] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_ice1712
Kernel modules: snd_ice1712
06:0e.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Gigabyte Technology Co., Ltd Motherboard [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 22
NUMA node: 0
Region 0: Memory at fdafe000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fdaf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: firewire_ohci
Kernel modules: firewire_ohci
06:0f.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10)
Subsystem: Gigabyte Technology Co., Ltd GA-MA69G-S3H Motherboard [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
NUMA node: 0
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at fdafd000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at fd980000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: r8169
Kernel modules: r8169
[ 0.000000] Linux version 4.9.2 (root@c21) (gcc version 6.3.0 20161229 (Debian 6.3.0-2) ) #1 SMP Fri Jan 13 20:21:28 CET 2017
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-4.9.2 root=/dev/md127p2 ro printk.time=1 single video=DVI-D-1:1920x1200-8@60D video=VGA-1:d video=HDMI-A-1:d
[ 0.000000] x86/fpu: Legacy x87 FPU detected.
[ 0.000000] x86/fpu: Using 'eager' FPU context switches.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x00000000000997ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cfedffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cfee0000-0x00000000cfee2fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000cfee3000-0x00000000cfeeffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000cfef0000-0x00000000cfefffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000022fffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI not present or invalid.
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x230000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back
[ 0.000000] 2 base 0000C0000000 mask FFFFF0000000 write-back
[ 0.000000] 3 base 0000CFF00000 mask FFFFFFF00000 uncachable
[ 0.000000] 4 base 000100000000 mask FFFF00000000 write-back
[ 0.000000] 5 base 000200000000 mask FFFFE0000000 write-back
[ 0.000000] 6 base 000220000000 mask FFFFF0000000 write-back
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 0000000230000000 aka 8960M
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] e820: update [mem 0xcff00000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xcfee0 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f4f50-0x000f4f5f] mapped at [ffff89b3400f4f50]
[ 0.000000] Base memory trampoline at [ffff89b340093000] 93000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] BRK [0x207d4a000, 0x207d4afff] PGTABLE
[ 0.000000] BRK [0x207d4b000, 0x207d4bfff] PGTABLE
[ 0.000000] BRK [0x207d4c000, 0x207d4cfff] PGTABLE
[ 0.000000] BRK [0x207d4d000, 0x207d4dfff] PGTABLE
[ 0.000000] BRK [0x207d4e000, 0x207d4efff] PGTABLE
[ 0.000000] BRK [0x207d4f000, 0x207d4ffff] PGTABLE
[ 0.000000] BRK [0x207d50000, 0x207d50fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x3626b000-0x3712cfff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F6920 000014 (v00 GBT )
[ 0.000000] ACPI: RSDT 0x00000000CFEE3000 000038 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: FACP 0x00000000CFEE3040 000074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: DSDT 0x00000000CFEE30C0 00494D (v01 GBT GBTUACPI 00001000 MSFT 03000000)
[ 0.000000] ACPI: FACS 0x00000000CFEE0000 000040
[ 0.000000] ACPI: SSDT 0x00000000CFEE7B00 00088C (v01 PTLTD POWERNOW 00000001 LTP 00000001)
[ 0.000000] ACPI: HPET 0x00000000CFEE83C0 000038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098)
[ 0.000000] ACPI: MCFG 0x00000000CFEE8400 00003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: APIC 0x00000000CFEE7A40 000084 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] Scanning NUMA topology in Northbridge 24
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000022fffffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x22fffb000-0x22fffffff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000022fffffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x0000000000098fff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x00000000cfedffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000022fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000022fffffff]
[ 0.000000] On node 0 totalpages: 2096760
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3992 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13244 pages used for memmap
[ 0.000000] DMA32 zone: 847584 pages, LIFO batch:31
[ 0.000000] Normal zone: 19456 pages used for memmap
[ 0.000000] Normal zone: 1245184 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10b9a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00099000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcfee0000-0xcfee2fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcfee3000-0xcfeeffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcfef0000-0xcfefffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcff00000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xffffffff]
[ 0.000000] e820: [mem 0xcff00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] percpu: Embedded 35 pages/cpu @ffff89b56fc00000 s103768 r8192 d31400 u524288
[ 0.000000] pcpu-alloc: s103768 r8192 d31400 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 2063975
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-4.9.2 root=/dev/md127p2 ro printk.time=1 single video=DVI-D-1:1920x1200-8@60D video=VGA-1:d video=HDMI-A-1:d
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] AGP: Node 0: aperture [bus addr 0xc4000000-0xc5ffffff] (32MB)
[ 0.000000] Aperture pointing to e820 RAM. Ignoring.
[ 0.000000] AGP: Your BIOS doesn't leave an aperture memory hole
[ 0.000000] AGP: Please enable the IOMMU option in the BIOS setup
[ 0.000000] AGP: This costs you 64MB of RAM
[ 0.000000] AGP: Mapping aperture over RAM [mem 0xc4000000-0xc7ffffff] (65536KB)
[ 0.000000] PM: Registered nosave memory: [mem 0xc4000000-0xc7ffffff]
[ 0.000000] Memory: 8092940K/8387040K available (6138K kernel code, 1134K rwdata, 2812K rodata, 1388K init, 812K bss, 294100K reserved, 0K cma-reserved)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:33024 nr_irqs:456 16
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration failed
[ 0.000000] tsc: Unable to calibrate against PIT
[ 0.000000] tsc: using HPET reference calibration
[ 0.000000] tsc: Detected 3207.269 MHz processor
[ 0.000019] Calibrating delay loop (skipped), value calculated using timer frequency.. 6414.53 BogoMIPS (lpj=12829076)
[ 0.000108] pid_max: default: 32768 minimum: 301
[ 0.000167] ACPI: Core revision 20160831
[ 0.002721] ACPI: 2 ACPI AML tables successfully acquired and loaded
[ 0.002856] Security Framework initialized
[ 0.002901] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.002951] AppArmor: AppArmor disabled by boot time parameter
[ 0.003356] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.006310] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.007570] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.007623] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.008007] CPU: Physical Processor ID: 0
[ 0.008051] CPU: Processor Core ID: 0
[ 0.008095] mce: CPU supports 6 MCE banks
[ 0.008143] LVT offset 0 assigned for vector 0xf9
[ 0.008191] Last level iTLB entries: 4KB 512, 2MB 16, 4MB 8
[ 0.008235] Last level dTLB entries: 4KB 512, 2MB 128, 4MB 64, 1GB 0
[ 0.008508] Freeing SMP alternatives memory: 24K (ffffffffb6478000 - ffffffffb647e000)
[ 0.035545] ftrace: allocating 24972 entries in 98 pages
[ 0.043263] smpboot: Max logical packages: 1
[ 0.043864] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.189342] smpboot: CPU0: AMD Phenom(tm) II X4 955 Processor (family: 0x10, model: 0x4, stepping: 0x3)
[ 0.189506] Performance Events: AMD PMU driver.
[ 0.189589] ... version: 0
[ 0.189632] ... bit width: 48
[ 0.189675] ... generic registers: 4
[ 0.189718] ... value mask: 0000ffffffffffff
[ 0.189761] ... max period: 00007fffffffffff
[ 0.189805] ... fixed-purpose events: 0
[ 0.189847] ... event mask: 000000000000000f
[ 0.190354] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.190519] x86: Booting SMP configuration:
[ 0.190563] .... node #0, CPUs: #1 #2 #3
[ 0.431417] x86: Booted up 1 node, 4 CPUs
[ 0.431503] smpboot: Total of 4 processors activated (25657.97 BogoMIPS)
[ 0.437278] devtmpfs: initialized
[ 0.437394] x86/mm: Memory block size: 128MB
[ 0.441042] PM: Registering ACPI NVS region [mem 0xcfee0000-0xcfee2fff] (12288 bytes)
[ 0.441151] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.441236] pinctrl core: initialized pinctrl subsystem
[ 0.441399] NET: Registered protocol family 16
[ 0.453359] cpuidle: using governor ladder
[ 0.469358] cpuidle: using governor menu
[ 0.469409] node 0 link 0: io port [b000, ffff]
[ 0.469410] TOM: 00000000d0000000 aka 3328M
[ 0.469454] Fam 10h mmconf [mem 0xe0000000-0xe00fffff]
[ 0.469456] node 0 link 0: mmio [a0000, bffff]
[ 0.469457] node 0 link 0: mmio [d0000000, dfffffff]
[ 0.469459] node 0 link 0: mmio [f0000000, fe02ffff]
[ 0.469460] node 0 link 0: mmio [e0000000, e06fffff] ==> [e0100000, e06fffff]
[ 0.469461] TOM2: 0000000230000000 aka 8960M
[ 0.469505] bus: [bus 00-06] on node 0 link 0
[ 0.469506] bus: 00 [io 0x0000-0xffff]
[ 0.469507] bus: 00 [mem 0x000a0000-0x000bffff]
[ 0.469507] bus: 00 [mem 0xd0000000-0xdfffffff]
[ 0.469508] bus: 00 [mem 0xe0700000-0xffffffff]
[ 0.469508] bus: 00 [mem 0xe0100000-0xe06fffff]
[ 0.469509] bus: 00 [mem 0x230000000-0xfcffffffff]
[ 0.469574] ACPI: bus type PCI registered
[ 0.469618] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.469699] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.469749] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.469810] PCI: Using configuration type 1 for base access
[ 0.470144] mtrr: your CPUs had inconsistent variable MTRR settings
[ 0.470189] mtrr: probably your BIOS does not setup all CPUs.
[ 0.470232] mtrr: corrected configuration.
[ 0.485543] HugeTLB registered 1 GB page size, pre-allocated 0 pages
[ 0.485590] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.485975] ACPI: Added _OSI(Module Device)
[ 0.486022] ACPI: Added _OSI(Processor Device)
[ 0.486066] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.486109] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.486328] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.491141] ACPI: Interpreter enabled
[ 0.491197] ACPI: (supports S0 S3 S4 S5)
[ 0.491240] ACPI: Using IOAPIC for interrupt routing
[ 0.491336] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.495034] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.495084] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.495135] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.495393] PCI host bridge to bus 0000:00
[ 0.495438] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.495483] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.495528] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.498051] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.498100] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfebfffff window]
[ 0.498149] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.498198] pci 0000:00:00.0: [1002:7910] type 00 class 0x060000
[ 0.498279] pci 0000:00:02.0: [1002:7913] type 01 class 0x060400
[ 0.498308] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[ 0.498346] pci 0000:00:02.0: System wakeup disabled by ACPI
[ 0.498424] pci 0000:00:04.0: [1002:7914] type 01 class 0x060400
[ 0.498451] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[ 0.498485] pci 0000:00:04.0: System wakeup disabled by ACPI
[ 0.498582] pci 0000:00:12.0: [1002:4380] type 00 class 0x010601
[ 0.498598] pci 0000:00:12.0: reg 0x10: [io 0xff00-0xff07]
[ 0.498607] pci 0000:00:12.0: reg 0x14: [io 0xfe00-0xfe03]
[ 0.498616] pci 0000:00:12.0: reg 0x18: [io 0xfd00-0xfd07]
[ 0.498624] pci 0000:00:12.0: reg 0x1c: [io 0xfc00-0xfc03]
[ 0.498633] pci 0000:00:12.0: reg 0x20: [io 0xfb00-0xfb0f]
[ 0.498642] pci 0000:00:12.0: reg 0x24: [mem 0xfe02f000-0xfe02f3ff]
[ 0.498740] pci 0000:00:13.0: [1002:4387] type 00 class 0x0c0310
[ 0.498752] pci 0000:00:13.0: reg 0x10: [mem 0xfe02e000-0xfe02efff]
[ 0.498843] pci 0000:00:13.0: System wakeup disabled by ACPI
[ 0.498920] pci 0000:00:13.1: [1002:4388] type 00 class 0x0c0310
[ 0.498933] pci 0000:00:13.1: reg 0x10: [mem 0xfe02d000-0xfe02dfff]
[ 0.499024] pci 0000:00:13.1: System wakeup disabled by ACPI
[ 0.499101] pci 0000:00:13.2: [1002:4389] type 00 class 0x0c0310
[ 0.499114] pci 0000:00:13.2: reg 0x10: [mem 0xfe02c000-0xfe02cfff]
[ 0.499204] pci 0000:00:13.2: System wakeup disabled by ACPI
[ 0.499285] pci 0000:00:13.3: [1002:438a] type 00 class 0x0c0310
[ 0.499298] pci 0000:00:13.3: reg 0x10: [mem 0xfe02b000-0xfe02bfff]
[ 0.499400] pci 0000:00:13.3: System wakeup disabled by ACPI
[ 0.499477] pci 0000:00:13.4: [1002:438b] type 00 class 0x0c0310
[ 0.499490] pci 0000:00:13.4: reg 0x10: [mem 0xfe02a000-0xfe02afff]
[ 0.499581] pci 0000:00:13.4: System wakeup disabled by ACPI
[ 0.499661] pci 0000:00:13.5: [1002:4386] type 00 class 0x0c0320
[ 0.499678] pci 0000:00:13.5: reg 0x10: [mem 0xfe029000-0xfe0290ff]
[ 0.499758] pci 0000:00:13.5: supports D1 D2
[ 0.499759] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
[ 0.499797] pci 0000:00:13.5: System wakeup disabled by ACPI
[ 0.499879] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
[ 0.499899] pci 0000:00:14.0: reg 0x10: [io 0x0b00-0x0b0f]
[ 0.500031] pci 0000:00:14.1: [1002:438c] type 00 class 0x01018a
[ 0.500044] pci 0000:00:14.1: reg 0x10: [io 0x0000-0x0007]
[ 0.500052] pci 0000:00:14.1: reg 0x14: [io 0x0000-0x0003]
[ 0.500061] pci 0000:00:14.1: reg 0x18: [io 0x0000-0x0007]
[ 0.500070] pci 0000:00:14.1: reg 0x1c: [io 0x0000-0x0003]
[ 0.500079] pci 0000:00:14.1: reg 0x20: [io 0xf900-0xf90f]
[ 0.500098] pci 0000:00:14.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.500143] pci 0000:00:14.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.500187] pci 0000:00:14.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.500232] pci 0000:00:14.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.500345] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
[ 0.500365] pci 0000:00:14.2: reg 0x10: [mem 0xfe024000-0xfe027fff 64bit]
[ 0.500432] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.500469] pci 0000:00:14.2: System wakeup disabled by ACPI
[ 0.500545] pci 0000:00:14.3: [1002:438d] type 00 class 0x060100
[ 0.500671] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
[ 0.500739] pci 0000:00:14.4: System wakeup disabled by ACPI
[ 0.500819] pci 0000:00:18.0: [1022:1200] type 00 class 0x060000
[ 0.500883] pci 0000:00:18.1: [1022:1201] type 00 class 0x060000
[ 0.500942] pci 0000:00:18.2: [1022:1202] type 00 class 0x060000
[ 0.501000] pci 0000:00:18.3: [1022:1203] type 00 class 0x060000
[ 0.501061] pci 0000:00:18.4: [1022:1204] type 00 class 0x060000
[ 0.501166] pci 0000:01:00.0: [1002:6837] type 00 class 0x030000
[ 0.501181] pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.501191] pci 0000:01:00.0: reg 0x18: [mem 0xfdd80000-0xfddbffff 64bit]
[ 0.501198] pci 0000:01:00.0: reg 0x20: [io 0xce00-0xceff]
[ 0.501210] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[ 0.501255] pci 0000:01:00.0: supports D1 D2
[ 0.501256] pci 0000:01:00.0: PME# supported from D1 D2 D3hot
[ 0.501312] pci 0000:01:00.1: [1002:aab0] type 00 class 0x040300
[ 0.501326] pci 0000:01:00.1: reg 0x10: [mem 0xfddfc000-0xfddfffff 64bit]
[ 0.501402] pci 0000:01:00.1: supports D1 D2
[ 0.515403] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 0.515451] pci 0000:00:02.0: bridge window [io 0xc000-0xcfff]
[ 0.515453] pci 0000:00:02.0: bridge window [mem 0xfdd00000-0xfddfffff]
[ 0.515455] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.515534] pci 0000:02:00.0: [12d8:2304] type 01 class 0x060400
[ 0.515630] pci 0000:02:00.0: Max Payload Size set to 128 (was 256, max 256)
[ 0.515785] pci 0000:02:00.0: supports D1 D2
[ 0.515786] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.527407] pci 0000:00:04.0: PCI bridge to [bus 02-05]
[ 0.527455] pci 0000:00:04.0: bridge window [io 0xd000-0xefff]
[ 0.527457] pci 0000:00:04.0: bridge window [mem 0xfdb00000-0xfdcfffff]
[ 0.527459] pci 0000:00:04.0: bridge window [mem 0xfde00000-0xfdffffff 64bit pref]
[ 0.527567] pci 0000:03:01.0: [12d8:2304] type 01 class 0x060400
[ 0.527642] pci 0000:03:01.0: Max Payload Size set to 128 (was 256, max 256)
[ 0.527796] pci 0000:03:01.0: supports D1 D2
[ 0.527797] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.527896] pci 0000:03:02.0: [12d8:2304] type 01 class 0x060400
[ 0.527969] pci 0000:03:02.0: Max Payload Size set to 128 (was 256, max 256)
[ 0.528114] pci 0000:03:02.0: supports D1 D2
[ 0.528114] pci 0000:03:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.528242] pci 0000:02:00.0: PCI bridge to [bus 03-05]
[ 0.528294] pci 0000:02:00.0: bridge window [io 0xd000-0xefff]
[ 0.528299] pci 0000:02:00.0: bridge window [mem 0xfdb00000-0xfdcfffff]
[ 0.528307] pci 0000:02:00.0: bridge window [mem 0xfde00000-0xfdffffff 64bit pref]
[ 0.528392] pci 0000:04:00.0: [1b73:1100] type 00 class 0x0c0330
[ 0.528424] pci 0000:04:00.0: reg 0x10: [mem 0xfdce0000-0xfdceffff 64bit]
[ 0.528445] pci 0000:04:00.0: reg 0x18: [mem 0xfdcff000-0xfdcfffff 64bit]
[ 0.528467] pci 0000:04:00.0: reg 0x20: [mem 0xfdcfe000-0xfdcfefff 64bit]
[ 0.528492] pci 0000:04:00.0: Max Payload Size set to 128 (was 256, max 512)
[ 0.528611] pci 0000:04:00.0: supports D1
[ 0.528612] pci 0000:04:00.0: PME# supported from D0 D1 D3hot
[ 0.528701] pci 0000:03:01.0: PCI bridge to [bus 04]
[ 0.528752] pci 0000:03:01.0: bridge window [io 0xe000-0xefff]
[ 0.528757] pci 0000:03:01.0: bridge window [mem 0xfdc00000-0xfdcfffff]
[ 0.528765] pci 0000:03:01.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
[ 0.528852] pci 0000:05:00.0: [11c1:5901] type 00 class 0x0c0010
[ 0.528884] pci 0000:05:00.0: reg 0x10: [mem 0xfdbff000-0xfdbfffff 64bit]
[ 0.528962] pci 0000:05:00.0: Max Payload Size set to 128 (was 256, max 256)
[ 0.529090] pci 0000:05:00.0: supports D1 D2
[ 0.529090] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot
[ 0.539412] pci 0000:03:02.0: PCI bridge to [bus 05]
[ 0.539467] pci 0000:03:02.0: bridge window [io 0xd000-0xdfff]
[ 0.539472] pci 0000:03:02.0: bridge window [mem 0xfdb00000-0xfdbfffff]
[ 0.539480] pci 0000:03:02.0: bridge window [mem 0xfde00000-0xfdefffff 64bit pref]
[ 0.539573] pci 0000:06:06.0: [1095:3124] type 00 class 0x010400
[ 0.539604] pci 0000:06:06.0: reg 0x10: [mem 0xfdaff000-0xfdaff07f 64bit]
[ 0.539623] pci 0000:06:06.0: reg 0x18: [mem 0xfdaf0000-0xfdaf7fff 64bit]
[ 0.539635] pci 0000:06:06.0: reg 0x20: [io 0xbf00-0xbf0f]
[ 0.539659] pci 0000:06:06.0: reg 0x30: [mem 0x00000000-0x0007ffff pref]
[ 0.539723] pci 0000:06:06.0: supports D1 D2
[ 0.539769] pci 0000:06:07.0: [1412:1712] type 00 class 0x040100
[ 0.539789] pci 0000:06:07.0: reg 0x10: [io 0xbe00-0xbe1f]
[ 0.539800] pci 0000:06:07.0: reg 0x14: [io 0xbd00-0xbd0f]
[ 0.539812] pci 0000:06:07.0: reg 0x18: [io 0xbc00-0xbc0f]
[ 0.539823] pci 0000:06:07.0: reg 0x1c: [io 0xbb00-0xbb3f]
[ 0.539891] pci 0000:06:07.0: supports D2
[ 0.539938] pci 0000:06:0e.0: [104c:8024] type 00 class 0x0c0010
[ 0.539959] pci 0000:06:0e.0: reg 0x10: [mem 0xfdafe000-0xfdafe7ff]
[ 0.539971] pci 0000:06:0e.0: reg 0x14: [mem 0xfdaf8000-0xfdafbfff]
[ 0.540064] pci 0000:06:0e.0: supports D1 D2
[ 0.540065] pci 0000:06:0e.0: PME# supported from D0 D1 D2 D3hot
[ 0.540113] pci 0000:06:0f.0: [10ec:8167] type 00 class 0x020000
[ 0.540132] pci 0000:06:0f.0: reg 0x10: [io 0xb800-0xb8ff]
[ 0.540143] pci 0000:06:0f.0: reg 0x14: [mem 0xfdafd000-0xfdafd0ff]
[ 0.540196] pci 0000:06:0f.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[ 0.540230] pci 0000:06:0f.0: supports D1 D2
[ 0.540231] pci 0000:06:0f.0: PME# supported from D1 D2 D3hot D3cold
[ 0.540292] pci 0000:00:14.4: PCI bridge to [bus 06] (subtractive decode)
[ 0.540339] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff]
[ 0.540342] pci 0000:00:14.4: bridge window [mem 0xfda00000-0xfdafffff]
[ 0.540345] pci 0000:00:14.4: bridge window [mem 0xfd900000-0xfd9fffff pref]
[ 0.540346] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode)
[ 0.540347] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.540348] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.540349] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 0.540350] pci 0000:00:14.4: bridge window [mem 0xd0000000-0xfebfffff window] (subtractive decode)
[ 0.540500] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 0.541005] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 0.541508] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 0.542010] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 0.542511] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 0.543013] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 0.543519] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 0.544019] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 0.544990] ACPI: Enabled 1 GPEs in block 00 to 1F
[ 0.545252] vgaarb: setting as boot device: PCI:0000:01:00.0
[ 0.545297] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.545346] vgaarb: loaded
[ 0.545389] vgaarb: bridge control possible 0000:01:00.0
[ 0.545464] dmi: Firmware registration failed.
[ 0.545561] PCI: Using ACPI for IRQ routing
[ 0.554455] PCI: pci_cache_line_size set to 64 bytes
[ 0.554534] e820: reserve RAM buffer [mem 0x00099800-0x0009ffff]
[ 0.554535] e820: reserve RAM buffer [mem 0xcfee0000-0xcfffffff]
[ 0.554750] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.554985] hpet0: 4 comparators, 32-bit 14.318180 MHz counter
[ 0.557091] clocksource: Switched to clocksource hpet
[ 0.563981] VFS: Disk quotas dquot_6.6.0
[ 0.564050] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.564175] pnp: PnP ACPI init
[ 0.564332] system 00:00: [io 0x04d0-0x04d1] has been reserved
[ 0.564377] system 00:00: [io 0x0220-0x0225] has been reserved
[ 0.564421] system 00:00: [io 0x0290-0x0294] has been reserved
[ 0.564467] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.564626] pnp 00:01: disabling [mem 0x00000000-0x00000fff window] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
[ 0.564682] pnp 00:01: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:06:06.0 BAR 6 [mem 0x00000000-0x0007ffff pref]
[ 0.564736] pnp 00:01: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:06:0f.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
[ 0.564806] system 00:01: [io 0x4100-0x411f] has been reserved
[ 0.564851] system 00:01: [io 0x0228-0x022f] has been reserved
[ 0.564895] system 00:01: [io 0x040b] has been reserved
[ 0.564939] system 00:01: [io 0x04d6] has been reserved
[ 0.564983] system 00:01: [io 0x0c00-0x0c01] has been reserved
[ 0.565027] system 00:01: [io 0x0c14] has been reserved
[ 0.565072] system 00:01: [io 0x0c50-0x0c52] has been reserved
[ 0.565128] system 00:01: [io 0x0c6c-0x0c6d] has been reserved
[ 0.565173] system 00:01: [io 0x0c6f] has been reserved
[ 0.565217] system 00:01: [io 0x0cd0-0x0cd1] has been reserved
[ 0.565261] system 00:01: [io 0x0cd2-0x0cd3] has been reserved
[ 0.565306] system 00:01: [io 0x0cd4-0x0cdf] has been reserved
[ 0.565350] system 00:01: [io 0x4000-0x40fe] has been reserved
[ 0.565394] system 00:01: [io 0x4210-0x4217] has been reserved
[ 0.565439] system 00:01: [io 0x0b00-0x0b1f] could not be reserved
[ 0.565483] system 00:01: [io 0x0238-0x023f] has been reserved
[ 0.565528] system 00:01: [mem 0xfee00400-0xfee00fff window] has been reserved
[ 0.565577] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.565704] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.565823] pnp 00:03: [dma 2]
[ 0.565847] pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.566092] pnp 00:04: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.566330] pnp 00:05: [dma 3]
[ 0.566362] pnp 00:05: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.566435] system 00:06: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.566481] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.566613] system 00:07: [mem 0x000d6000-0x000d7fff] has been reserved
[ 0.566659] system 00:07: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.566703] system 00:07: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.566748] system 00:07: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.566792] system 00:07: [mem 0xcfee0000-0xcfefffff] could not be reserved
[ 0.566837] system 00:07: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.566882] system 00:07: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.566926] system 00:07: [mem 0x00100000-0xcfedffff] could not be reserved
[ 0.566971] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.567016] system 00:07: [mem 0xfee00000-0xfee00fff] could not be reserved
[ 0.567060] system 00:07: [mem 0xfff80000-0xfffeffff] has been reserved
[ 0.567105] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.567118] pnp: PnP ACPI: found 8 devices
[ 0.573881] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.573989] pci 0000:01:00.0: BAR 6: assigned [mem 0xfdd00000-0xfdd1ffff pref]
[ 0.574038] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 0.574083] pci 0000:00:02.0: bridge window [io 0xc000-0xcfff]
[ 0.574128] pci 0000:00:02.0: bridge window [mem 0xfdd00000-0xfddfffff]
[ 0.574173] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.574223] pci 0000:03:01.0: PCI bridge to [bus 04]
[ 0.574269] pci 0000:03:01.0: bridge window [io 0xe000-0xefff]
[ 0.574319] pci 0000:03:01.0: bridge window [mem 0xfdc00000-0xfdcfffff]
[ 0.574367] pci 0000:03:01.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
[ 0.574422] pci 0000:03:02.0: PCI bridge to [bus 05]
[ 0.574468] pci 0000:03:02.0: bridge window [io 0xd000-0xdfff]
[ 0.574518] pci 0000:03:02.0: bridge window [mem 0xfdb00000-0xfdbfffff]
[ 0.574566] pci 0000:03:02.0: bridge window [mem 0xfde00000-0xfdefffff 64bit pref]
[ 0.574621] pci 0000:02:00.0: PCI bridge to [bus 03-05]
[ 0.574667] pci 0000:02:00.0: bridge window [io 0xd000-0xefff]
[ 0.574717] pci 0000:02:00.0: bridge window [mem 0xfdb00000-0xfdcfffff]
[ 0.574765] pci 0000:02:00.0: bridge window [mem 0xfde00000-0xfdffffff 64bit pref]
[ 0.574820] pci 0000:00:04.0: PCI bridge to [bus 02-05]
[ 0.574864] pci 0000:00:04.0: bridge window [io 0xd000-0xefff]
[ 0.574909] pci 0000:00:04.0: bridge window [mem 0xfdb00000-0xfdcfffff]
[ 0.574954] pci 0000:00:04.0: bridge window [mem 0xfde00000-0xfdffffff 64bit pref]
[ 0.575005] pci 0000:06:06.0: BAR 6: assigned [mem 0xfd900000-0xfd97ffff pref]
[ 0.575054] pci 0000:06:0f.0: BAR 6: assigned [mem 0xfd980000-0xfd99ffff pref]
[ 0.575103] pci 0000:00:14.4: PCI bridge to [bus 06]
[ 0.575147] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff]
[ 0.575195] pci 0000:00:14.4: bridge window [mem 0xfda00000-0xfdafffff]
[ 0.575241] pci 0000:00:14.4: bridge window [mem 0xfd900000-0xfd9fffff pref]
[ 0.575295] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.575296] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.575297] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.575298] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff window]
[ 0.575299] pci_bus 0000:00: resource 8 [mem 0xd0000000-0xfebfffff window]
[ 0.575300] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
[ 0.575301] pci_bus 0000:01: resource 1 [mem 0xfdd00000-0xfddfffff]
[ 0.575301] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.575303] pci_bus 0000:02: resource 0 [io 0xd000-0xefff]
[ 0.575303] pci_bus 0000:02: resource 1 [mem 0xfdb00000-0xfdcfffff]
[ 0.575304] pci_bus 0000:02: resource 2 [mem 0xfde00000-0xfdffffff 64bit pref]
[ 0.575305] pci_bus 0000:03: resource 0 [io 0xd000-0xefff]
[ 0.575306] pci_bus 0000:03: resource 1 [mem 0xfdb00000-0xfdcfffff]
[ 0.575307] pci_bus 0000:03: resource 2 [mem 0xfde00000-0xfdffffff 64bit pref]
[ 0.575308] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.575309] pci_bus 0000:04: resource 1 [mem 0xfdc00000-0xfdcfffff]
[ 0.575310] pci_bus 0000:04: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref]
[ 0.575311] pci_bus 0000:05: resource 0 [io 0xd000-0xdfff]
[ 0.575312] pci_bus 0000:05: resource 1 [mem 0xfdb00000-0xfdbfffff]
[ 0.575313] pci_bus 0000:05: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref]
[ 0.575314] pci_bus 0000:06: resource 0 [io 0xb000-0xbfff]
[ 0.575315] pci_bus 0000:06: resource 1 [mem 0xfda00000-0xfdafffff]
[ 0.575316] pci_bus 0000:06: resource 2 [mem 0xfd900000-0xfd9fffff pref]
[ 0.575317] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7 window]
[ 0.575318] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff window]
[ 0.575318] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.575319] pci_bus 0000:06: resource 7 [mem 0x000c0000-0x000dffff window]
[ 0.575320] pci_bus 0000:06: resource 8 [mem 0xd0000000-0xfebfffff window]
[ 0.575424] NET: Registered protocol family 2
[ 0.575655] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.575878] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.576242] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.576341] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.576436] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.576569] NET: Registered protocol family 1
[ 1.037374] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 1.037547] PCI: CLS 4 bytes, default 64
[ 1.037596] Unpacking initramfs...
[ 2.404026] Freeing initrd memory: 15112K (ffff89b37626b000 - ffff89b37712d000)
[ 2.404368] PCI-DMA: Disabling AGP.
[ 2.404511] PCI-DMA: aperture base @ c4000000 size 65536 KB
[ 2.404555] PCI-DMA: using GART IOMMU.
[ 2.404600] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 2.407924] LVT offset 1 assigned for vector 0x400
[ 2.407981] IBS: LVT offset 1 assigned
[ 2.408157] perf: AMD IBS detected (0x0000001f)
[ 2.408524] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 2.408596] audit: initializing netlink subsys (disabled)
[ 2.408663] audit: type=2000 audit(1484393533.296:1): initialized
[ 2.408974] Initialise system trusted keyrings
[ 2.409193] workingset: timestamp_bits=40 max_order=21 bucket_order=0
[ 2.409293] zbud: loaded
[ 2.454442] Key type asymmetric registered
[ 2.454491] Asymmetric key parser 'x509' registered
[ 2.454576] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 2.454664] io scheduler noop registered
[ 2.454708] io scheduler deadline registered
[ 2.454755] io scheduler cfq registered (default)
[ 2.455507] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 2.455555] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 2.455758] GHES: HEST is not enabled!
[ 2.455870] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.476468] 00:04: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 2.476941] Linux agpgart interface v0.103
[ 2.477012] AMD IOMMUv2 driver by Joerg Roedel <jroedel@xxxxxxx>
[ 2.477056] AMD IOMMUv2 functionality not available on this system
[ 2.479968] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 2.513615] i8042: Failed to disable AUX port, but continuing anyway... Is this a SiS?
[ 2.513663] i8042: If AUX port is really absent please use the 'i8042.noaux' option
[ 2.797233] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.797443] mousedev: PS/2 mouse device common for all mice
[ 2.797535] rtc_cmos 00:02: RTC can wake from S4
[ 2.797692] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 2.797771] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram, hpet irqs
[ 2.797909] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.797952] dmi-sysfs: dmi entry is absent.
[ 2.798119] NET: Registered protocol family 10
[ 2.798377] mip6: Mobile IPv6
[ 2.798421] NET: Registered protocol family 17
[ 2.798466] mpls_gso: MPLS GSO support
[ 2.798730] microcode: CPU0: patch_level=0x010000af
[ 2.798783] microcode: CPU1: patch_level=0x010000af
[ 2.798844] microcode: CPU2: patch_level=0x010000af
[ 2.798909] microcode: CPU3: patch_level=0x010000af
[ 2.798992] microcode: Microcode Update Driver: v2.01 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
[ 2.799165] registered taskstats version 1
[ 2.799210] Loading compiled-in X.509 certificates
[ 2.799265] zswap: loaded using pool lzo/zbud
[ 2.799749] rtc_cmos 00:02: setting system clock to 2017-01-14 11:32:13 UTC (1484393533)
[ 2.799844] PM: Hibernation image not present or could not be loaded.
[ 2.801085] Freeing unused kernel memory: 1388K (ffffffffb631d000 - ffffffffb6478000)
[ 2.801160] Write protecting the kernel read-only data: 12288k
[ 2.801844] Freeing unused kernel memory: 2040K (ffff89b547402000 - ffff89b547600000)
[ 2.804783] Freeing unused kernel memory: 1284K (ffff89b5478bf000 - ffff89b547a00000)
[ 2.810210] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 2.823232] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.823338] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.823390] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.823443] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 2.824136] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.824211] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.825023] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.825386] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.825480] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.825568] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.842139] fjes: module verification failed: signature and/or required key missing - tainting kernel
[ 2.842553] FUJITSU Extended Socket Network Device Driver - version 1.1 - Copyright (c) 2015 FUJITSU LIMITED
[ 2.843356] Floppy drive(s): fd0 is 1.44M
[ 2.848479] SCSI subsystem initialized
[ 2.849152] ACPI: bus type USB registered
[ 2.849221] usbcore: registered new interface driver usbfs
[ 2.849274] usbcore: registered new interface driver hub
[ 2.849337] usbcore: registered new device driver usb
[ 2.849584] [drm] Initialized
[ 2.849832] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.850434] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.850734] ehci-pci: EHCI PCI platform driver
[ 2.850893] libata version 3.00 loaded.
[ 2.850976] ehci-pci 0000:00:13.5: EHCI Host Controller
[ 2.851031] ehci-pci 0000:00:13.5: new USB bus registered, assigned bus number 1
[ 2.851088] ehci-pci 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
[ 2.851150] ehci-pci 0000:00:13.5: debug port 1
[ 2.851253] ehci-pci 0000:00:13.5: irq 19, io mem 0xfe029000
[ 2.852904] sata_sil24 0000:06:06.0: version 1.1
[ 2.853794] scsi host0: sata_sil24
[ 2.853949] scsi host1: sata_sil24
[ 2.854075] scsi host2: sata_sil24
[ 2.854219] scsi host3: sata_sil24
[ 2.854311] ata1: SATA max UDMA/100 host m128@0xfdaff000 port 0xfdaf0000 irq 20
[ 2.854367] ata2: SATA max UDMA/100 host m128@0xfdaff000 port 0xfdaf2000 irq 20
[ 2.854424] ata3: SATA max UDMA/100 host m128@0xfdaff000 port 0xfdaf4000 irq 20
[ 2.854476] ata4: SATA max UDMA/100 host m128@0xfdaff000 port 0xfdaf6000 irq 20
[ 2.854598] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.854765] r8169 0000:06:0f.0 (unnamed net_device) (uninitialized): not PCI Express
[ 2.855109] r8169 0000:06:0f.0 eth0: RTL8169sc/8110sc at 0xffffb7b900c91000, 00:1a:4d:9a:6d:99, XID 18000000 IRQ 23
[ 2.855161] r8169 0000:06:0f.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[ 2.859817] [drm] radeon kernel modesetting enabled.
[ 2.861011] [drm] initializing kernel modesetting (VERDE 0x1002:0x6837 0x1787:0x2330 0x00).
[ 2.861072] [drm] register mmio base: 0xFDD80000
[ 2.861137] [drm] register mmio size: 262144
[ 2.861243] radeon 0000:01:00.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0xffff
[ 2.861696] ATOM BIOS: C44101
[ 2.861907] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[ 2.861957] radeon 0000:01:00.0: GTT: 2048M 0x0000000040000000 - 0x00000000BFFFFFFF
[ 2.862013] [drm] Detected VRAM RAM=1024M, BAR=256M
[ 2.862062] [drm] RAM width 128bits DDR
[ 2.862177] [TTM] Zone kernel: Available graphics memory: 4089370 kiB
[ 2.862225] [TTM] Zone dma32: Available graphics memory: 2097152 kiB
[ 2.862270] [TTM] Initializing pool allocator
[ 2.862322] [TTM] Initializing DMA pool allocator
[ 2.862387] [drm] radeon: 1024M of VRAM memory ready
[ 2.862431] [drm] radeon: 2048M of GTT memory ready.
[ 2.862488] [drm] Loading verde Microcode
[ 2.862554] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_pfp.bin
[ 2.862615] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_me.bin
[ 2.862680] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_ce.bin
[ 2.862743] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_rlc.bin
[ 2.862810] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_mc.bin
[ 2.862887] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/verde_smc.bin
[ 2.862938] [drm] Internal thermal controller with fan control
[ 2.863047] [drm] probing gen 2 caps for device 1002:7913 = 100d01/0
[ 2.865354] FDC 0 is a post-1991 82077
[ 2.869116] ehci-pci 0000:00:13.5: USB 2.0 started, EHCI 1.00
[ 2.869206] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.869255] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.869304] usb usb1: Product: EHCI Host Controller
[ 2.869354] usb usb1: Manufacturer: Linux 4.9.2 ehci_hcd
[ 2.869398] usb usb1: SerialNumber: 0000:00:13.5
[ 2.869583] hub 1-0:1.0: USB hub found
[ 2.869642] hub 1-0:1.0: 10 ports detected
[ 2.869912] ahci 0000:00:12.0: version 3.0
[ 2.870031] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
[ 2.870239] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 2.870336] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part ccc
[ 2.870605] ohci-pci: OHCI PCI platform driver
[ 2.871068] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 2.871140] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 2
[ 2.871363] [drm] radeon: dpm initialized
[ 2.871552] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/TAHITI_uvd.bin
[ 2.871701] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/TAHITI_vce.bin
[ 2.872466] [drm] Found VCE firmware/feedback version 50.0.1 / 17!
[ 2.872575] [drm] GART: num cpu pages 524288, num gpu pages 524288
[ 2.872668] xhci_hcd 0000:04:00.0: hcc params 0x200071e1 hci version 0x100 quirks 0x00000010
[ 2.872925] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.872971] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.873025] usb usb2: Product: xHCI Host Controller
[ 2.873073] usb usb2: Manufacturer: Linux 4.9.2 xhci-hcd
[ 2.873148] usb usb2: SerialNumber: 0000:04:00.0
[ 2.873477] hub 2-0:1.0: USB hub found
[ 2.873540] hub 2-0:1.0: 4 ports detected
[ 2.873739] xhci_hcd 0000:04:00.0: xHCI Host Controller
[ 2.873792] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3
[ 2.873862] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.873936] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.873984] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.874032] usb usb3: Product: xHCI Host Controller
[ 2.874082] usb usb3: Manufacturer: Linux 4.9.2 xhci-hcd
[ 2.874126] usb usb3: SerialNumber: 0000:04:00.0
[ 2.874700] hub 3-0:1.0: USB hub found
[ 2.874871] hub 3-0:1.0: 4 ports detected
[ 2.875504] [drm] probing gen 2 caps for device 1002:7913 = 100d01/0
[ 2.877835] scsi host4: ahci
[ 2.881155] scsi host5: ahci
[ 2.881376] scsi host6: ahci
[ 2.881565] scsi host7: ahci
[ 2.881715] ata5: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
[ 2.881830] ata6: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
[ 2.882625] r8169 0000:06:0f.0 enp6s15: renamed from eth0
[ 2.886417] ata7: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
[ 2.886505] ata8: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
[ 2.887587] scsi host8: pata_atiixp
[ 2.887817] scsi host9: pata_atiixp
[ 2.887949] ata9: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14
[ 2.888045] ata10: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15
[ 2.888168] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 2.888298] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb10
[ 2.888544] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 2.888683] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 4
[ 2.888842] ohci-pci 0000:00:13.0: irq 16, io mem 0xfe02e000
[ 2.894834] [drm] PCIE GART of 2048M enabled (table at 0x00000000001D6000).
[ 2.894998] radeon 0000:01:00.0: WB enabled
[ 2.895043] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff89b55f9b9c00
[ 2.895093] radeon 0000:01:00.0: fence driver on ring 1 use gpu addr 0x0000000040000c04 and cpu addr 0xffff89b55f9b9c04
[ 2.895142] radeon 0000:01:00.0: fence driver on ring 2 use gpu addr 0x0000000040000c08 and cpu addr 0xffff89b55f9b9c08
[ 2.895192] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff89b55f9b9c0c
[ 2.895241] radeon 0000:01:00.0: fence driver on ring 4 use gpu addr 0x0000000040000c10 and cpu addr 0xffff89b55f9b9c10
[ 2.895741] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x0000000000075a18 and cpu addr 0xffffb7b901635a18
[ 2.915851] radeon 0000:01:00.0: fence driver on ring 6 use gpu addr 0x0000000040000c18 and cpu addr 0xffff89b55f9b9c18
[ 2.915901] radeon 0000:01:00.0: fence driver on ring 7 use gpu addr 0x0000000040000c1c and cpu addr 0xffff89b55f9b9c1c
[ 2.915975] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.916026] [drm] Driver supports precise vblank timestamp query.
[ 2.916073] radeon 0000:01:00.0: radeon: MSI limited to 32-bit
[ 2.916162] radeon 0000:01:00.0: radeon: using MSI.
[ 2.916239] [drm] radeon: irq initialized.
[ 2.925180] firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0, physUB
[ 2.953176] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.953240] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.953306] usb usb4: Product: OHCI PCI host controller
[ 2.953367] usb usb4: Manufacturer: Linux 4.9.2 ohci_hcd
[ 2.953428] usb usb4: SerialNumber: 0000:00:13.0
[ 2.953617] hub 4-0:1.0: USB hub found
[ 2.953693] hub 4-0:1.0: 2 ports detected
[ 2.953942] ohci-pci 0000:00:13.1: OHCI PCI host controller
[ 2.954007] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 5
[ 2.954109] ohci-pci 0000:00:13.1: irq 17, io mem 0xfe02d000
[ 2.985180] firewire_ohci 0000:06:0e.0: added OHCI v1.10 device as card 1, 4 IR + 8 IT contexts, quirks 0x2
[ 3.021177] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.021241] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.021307] usb usb5: Product: OHCI PCI host controller
[ 3.021368] usb usb5: Manufacturer: Linux 4.9.2 ohci_hcd
[ 3.021429] usb usb5: SerialNumber: 0000:00:13.1
[ 3.021613] hub 5-0:1.0: USB hub found
[ 3.021689] hub 5-0:1.0: 2 ports detected
[ 3.021943] ohci-pci 0000:00:13.2: OHCI PCI host controller
[ 3.022008] ohci-pci 0000:00:13.2: new USB bus registered, assigned bus number 6
[ 3.022111] ohci-pci 0000:00:13.2: irq 18, io mem 0xfe02c000
[ 3.052125] ata9.00: ATAPI: ASUS DRW-1814BL, 1.14, max UDMA/66
[ 3.057341] ata9.00: configured for UDMA/66
[ 3.085182] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.085245] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.085311] usb usb6: Product: OHCI PCI host controller
[ 3.085372] usb usb6: Manufacturer: Linux 4.9.2 ohci_hcd
[ 3.085434] usb usb6: SerialNumber: 0000:00:13.2
[ 3.085623] hub 6-0:1.0: USB hub found
[ 3.085702] hub 6-0:1.0: 2 ports detected
[ 3.085954] ohci-pci 0000:00:13.3: OHCI PCI host controller
[ 3.086020] ohci-pci 0000:00:13.3: new USB bus registered, assigned bus number 7
[ 3.086108] ohci-pci 0000:00:13.3: irq 17, io mem 0xfe02b000
[ 3.153163] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.153227] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.153292] usb usb7: Product: OHCI PCI host controller
[ 3.153354] usb usb7: Manufacturer: Linux 4.9.2 ohci_hcd
[ 3.153415] usb usb7: SerialNumber: 0000:00:13.3
[ 3.153583] hub 7-0:1.0: USB hub found
[ 3.153659] hub 7-0:1.0: 2 ports detected
[ 3.153885] ohci-pci 0000:00:13.4: OHCI PCI host controller
[ 3.153949] ohci-pci 0000:00:13.4: new USB bus registered, assigned bus number 8
[ 3.154047] ohci-pci 0000:00:13.4: irq 18, io mem 0xfe02a000
[ 3.199705] ata8: SATA link down (SStatus 0 SControl 300)
[ 3.205129] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 3.217168] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.217231] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.217296] usb usb8: Product: OHCI PCI host controller
[ 3.217357] usb usb8: Manufacturer: Linux 4.9.2 ohci_hcd
[ 3.217418] usb usb8: SerialNumber: 0000:00:13.4
[ 3.217588] hub 8-0:1.0: USB hub found
[ 3.217663] hub 8-0:1.0: 2 ports detected
[ 3.361131] ata7: softreset failed (device not ready)
[ 3.361196] ata7: applying PMP SRST workaround and retrying
[ 3.377529] usb 1-1: New USB device found, idVendor=03f0, idProduct=0610
[ 3.377592] usb 1-1: New USB device strings: Mfr=10, Product=11, SerialNumber=0
[ 3.377658] usb 1-1: Product: USB2.0 HUB
[ 3.377718] usb 1-1: Manufacturer: Genesyslogic
[ 3.378171] hub 1-1:1.0: USB hub found
[ 3.379915] hub 1-1:1.0: 4 ports detected
[ 3.437206] firewire_core 0000:05:00.0: created device fw0: GUID 00309300000001c3, S800
[ 3.441187] tsc: Refined TSC clocksource calibration: 3207.272 MHz
[ 3.441259] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2e3b1f431f7, max_idle_ns: 440795241363 ns
[ 3.501195] firewire_core 0000:06:0e.0: created device fw1: GUID 001a4d0000eb2917, S400
[ 3.503056] [drm] ring test on 0 succeeded in 1 usecs
[ 3.503107] [drm] ring test on 1 succeeded in 1 usecs
[ 3.503154] [drm] ring test on 2 succeeded in 1 usecs
[ 3.503212] [drm] ring test on 3 succeeded in 10 usecs
[ 3.503267] [drm] ring test on 4 succeeded in 10 usecs
[ 3.521140] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.521313] ata7.00: ATA-8: OCZ-VECTOR180, 1.01, max UDMA/133
[ 3.521360] ata7.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[ 3.521406] ata7.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.522443] ata7.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.522490] ata7.00: configured for UDMA/133
[ 3.573130] ata5: softreset failed (device not ready)
[ 3.573177] ata5: applying PMP SRST workaround and retrying
[ 3.573240] ata6: softreset failed (device not ready)
[ 3.573287] ata6: applying PMP SRST workaround and retrying
[ 3.679100] [drm] ring test on 5 succeeded in 1 usecs
[ 3.679151] [drm] UVD initialized successfully.
[ 3.733138] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.733210] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.734479] ata6.00: HPA detected: current 3907020911, native 3907029168
[ 3.734631] ata6.00: ATA-8: Hitachi HDS5C3020ALA632, ML6OA580, max UDMA/133
[ 3.734676] ata6.00: 3907020911 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 3.734725] ata6.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.736209] ata6.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.736255] ata6.00: configured for UDMA/133
[ 3.737122] usb 1-1.1: new full-speed USB device number 4 using ehci-pci
[ 3.738726] ata5.00: ATA-8: WDC WD10EARS-00MVWB0, 51.0AB51, max UDMA/133
[ 3.738773] ata5.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 3.738822] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.743261] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
[ 3.743307] ata5.00: configured for UDMA/133
[ 3.788406] [drm] ring test on 6 succeeded in 18 usecs
[ 3.788465] [drm] ring test on 7 succeeded in 4 usecs
[ 3.788508] [drm] VCE initialized successfully.
[ 3.788655] [drm] ib test on ring 0 succeeded in 0 usecs
[ 3.788731] [drm] ib test on ring 1 succeeded in 0 usecs
[ 3.788804] [drm] ib test on ring 2 succeeded in 0 usecs
[ 3.788892] [drm] ib test on ring 3 succeeded in 0 usecs
[ 3.788978] [drm] ib test on ring 4 succeeded in 0 usecs
[ 3.857720] usb 1-1.1: New USB device found, idVendor=046d, idProduct=c042
[ 3.857767] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.857815] usb 1-1.1: Product: USB Gaming Mouse
[ 3.857859] usb 1-1.1: Manufacturer: Logitech
[ 3.860923] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.870963] usbcore: registered new interface driver usbhid
[ 3.871010] usbhid: USB HID core driver
[ 3.871666] input: Logitech USB Gaming Mouse as /devices/pci0000:00/0000:00:13.5/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C042.0001/input/input1
[ 3.871798] hid-generic 0003:046D:C042.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:13.5-1.1/input0
[ 3.872818] hid-generic 0003:046D:C042.0002: hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:13.5-1.1/input1
[ 3.965137] usb 7-1: new full-speed USB device number 2 using ohci-pci
[ 3.965139] usb 1-8: new high-speed USB device number 5 using ehci-pci
[ 4.117522] usb 1-8: New USB device found, idVendor=05e3, idProduct=070e
[ 4.117569] usb 1-8: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[ 4.120169] usb 1-8: Product: USB Reader
[ 4.120213] usb 1-8: Manufacturer: Genesys
[ 4.120256] usb 1-8: SerialNumber: 000000590523
[ 4.122861] usb-storage 1-8:1.0: USB Mass Storage device detected
[ 4.123056] scsi host10: usb-storage 1-8:1.0
[ 4.123169] usbcore: registered new interface driver usb-storage
[ 4.123509] usbcore: registered new interface driver uas
[ 4.164139] usb 7-1: New USB device found, idVendor=0a5c, idProduct=21e8
[ 4.164186] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.164231] usb 7-1: Product: BCM920702 Bluetooth 4.0
[ 4.164274] usb 7-1: Manufacturer: Broadcom Corp
[ 4.164318] usb 7-1: SerialNumber: 5CF3707BF326
[ 4.193124] usb 1-1.2: new low-speed USB device number 6 using ehci-pci
[ 4.321298] usb 1-1.2: New USB device found, idVendor=04d9, idProduct=1603
[ 4.321345] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.321393] usb 1-1.2: Product: USB Keyboard
[ 4.321436] usb 1-1.2: Manufacturer:
[ 4.331906] input: USB Keyboard as /devices/pci0000:00/0000:00:13.5/usb1/1-1/1-1.2/1-1.2:1.0/0003:04D9:1603.0003/input/input2
[ 4.389252] hid-generic 0003:04D9:1603.0003: input,hidraw2: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:13.5-1.2/input0
[ 4.406353] input: USB Keyboard as /devices/pci0000:00/0000:00:13.5/usb1/1-1/1-1.2/1-1.2:1.1/0003:04D9:1603.0004/input/input3
[ 4.421128] usb 1-9: new high-speed USB device number 7 using ehci-pci
[ 4.461159] [drm] ib test on ring 5 succeeded
[ 4.461229] clocksource: Switched to clocksource tsc
[ 4.465165] hid-generic 0003:04D9:1603.0004: input,hidraw3: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:13.5-1.2/input1
[ 4.572950] usb 1-9: New USB device found, idVendor=05e3, idProduct=0716
[ 4.572997] usb 1-9: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[ 4.573041] usb 1-9: Product: USB Storage
[ 4.573085] usb 1-9: SerialNumber: 000000009744
[ 4.573726] usb-storage 1-9:1.0: USB Mass Storage device detected
[ 4.573859] scsi host11: usb-storage 1-9:1.0
[ 4.917131] ata1: SATA link down (SStatus 0 SControl 0)
[ 4.973141] [drm] ib test on ring 6 succeeded
[ 5.134285] scsi 10:0:0:0: Direct-Access Generic STORAGE DEVICE 9325 PQ: 0 ANSI: 0
[ 5.135161] scsi 10:0:0:1: Direct-Access Generic STORAGE DEVICE 9325 PQ: 0 ANSI: 0
[ 5.139120] random: fast init done
[ 5.139389] sd 10:0:0:0: [sda] Attached SCSI removable disk
[ 5.140013] sd 10:0:0:1: [sdb] Attached SCSI removable disk
[ 5.485144] [drm] ib test on ring 7 succeeded
[ 5.485219] [drm] hw_i2c forced on, you may experience display detection problems!
[ 5.485507] [drm] forcing HDMI-A-1 connector OFF
[ 5.485598] [drm] forcing DVI-D-1 connector ON
[ 5.485676] [drm] forcing VGA-1 connector OFF
[ 5.485743] [drm] Radeon Display Connectors
[ 5.485786] [drm] Connector 0:
[ 5.485829] [drm] HDMI-A-1
[ 5.485871] [drm] HPD1
[ 5.485914] [drm] DDC: 0x6570 0x6570 0x6574 0x6574 0x6578 0x6578 0x657c 0x657c
[ 5.485962] [drm] Encoders:
[ 5.486004] [drm] DFP1: INTERNAL_UNIPHY2
[ 5.486047] [drm] Connector 1:
[ 5.486089] [drm] DVI-D-1
[ 5.486132] [drm] HPD2
[ 5.486175] [drm] DDC: 0x6560 0x6560 0x6564 0x6564 0x6568 0x6568 0x656c 0x656c
[ 5.486222] [drm] Encoders:
[ 5.486265] [drm] DFP2: INTERNAL_UNIPHY
[ 5.486307] [drm] Connector 2:
[ 5.486350] [drm] VGA-1
[ 5.486392] [drm] DDC: 0x6540 0x6540 0x6544 0x6544 0x6548 0x6548 0x654c 0x654c
[ 5.486440] [drm] Encoders:
[ 5.486482] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 5.517096] [drm] fb mappable at 0xD05D9000
[ 5.517139] [drm] vram apper at 0xD0000000
[ 5.517182] [drm] size 2457600
[ 5.517225] [drm] fb depth is 8
[ 5.517267] [drm] pitch is 2048
[ 5.517376] fbcon: radeondrmfb (fb0) is primary device
[ 5.572944] Console: switching to colour frame buffer device 240x75
[ 5.574467] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[ 5.582461] scsi 11:0:0:0: Direct-Access Generic STORAGE DEVICE 9744 PQ: 0 ANSI: 0
[ 5.583336] scsi 11:0:0:1: Direct-Access Generic STORAGE DEVICE 9744 PQ: 0 ANSI: 0
[ 5.591698] sd 11:0:0:0: [sdc] Attached SCSI removable disk
[ 5.592329] sd 11:0:0:1: [sdd] Attached SCSI removable disk
[ 5.593474] [drm] Initialized radeon 2.48.0 20080528 for 0000:01:00.0 on minor 0
[ 7.097288] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 7.098176] ata2.00: HPA detected: current 312579695, native 312581808
[ 7.098195] ata2.00: ATA-7: Hitachi HDS721616PLA380, P22OABEA, max UDMA/133
[ 7.098205] ata2.00: 312579695 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 7.099255] ata2.00: configured for UDMA/100
[ 7.099452] scsi 1:0:0:0: Direct-Access ATA Hitachi HDS72161 ABEA PQ: 0 ANSI: 5
[ 7.129293] sd 1:0:0:0: [sde] 312579695 512-byte logical blocks: (160 GB/149 GiB)
[ 7.129411] sd 1:0:0:0: [sde] Write Protect is off
[ 7.129424] sd 1:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 7.129453] sd 1:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.151580] sd 1:0:0:0: [sde] Attached SCSI disk
[ 9.309288] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 9.310172] ata3.00: HPA detected: current 312579695, native 312581808
[ 9.310187] ata3.00: ATA-7: Hitachi HDS721616PLA380, P22OABEA, max UDMA/133
[ 9.310197] ata3.00: 312579695 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 9.311246] ata3.00: configured for UDMA/100
[ 9.311422] scsi 2:0:0:0: Direct-Access ATA Hitachi HDS72161 ABEA PQ: 0 ANSI: 5
[ 9.341303] sd 2:0:0:0: [sdf] 312579695 512-byte logical blocks: (160 GB/149 GiB)
[ 9.341403] sd 2:0:0:0: [sdf] Write Protect is off
[ 9.341416] sd 2:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 9.341446] sd 2:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.369882] sd 2:0:0:0: [sdf] Attached SCSI disk
[ 11.393137] ata4: SATA link down (SStatus 0 SControl 0)
[ 11.393334] scsi 4:0:0:0: Direct-Access ATA WDC WD10EARS-00M AB51 PQ: 0 ANSI: 5
[ 11.425292] sd 4:0:0:0: [sdg] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 11.425307] sd 4:0:0:0: [sdg] 4096-byte physical blocks
[ 11.425410] sd 4:0:0:0: [sdg] Write Protect is off
[ 11.425422] sd 4:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 11.425438] scsi 5:0:0:0: Direct-Access ATA Hitachi HDS5C302 A580 PQ: 0 ANSI: 5
[ 11.425449] sd 4:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.442088] sdg: sdg1 sdg2 sdg3
[ 11.442481] sd 4:0:0:0: [sdg] Attached SCSI disk
[ 11.457273] sd 5:0:0:0: [sdh] 3907020911 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 11.457368] sd 5:0:0:0: [sdh] Write Protect is off
[ 11.457380] sd 5:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 11.457399] scsi 6:0:0:0: Direct-Access ATA OCZ-VECTOR180 1.01 PQ: 0 ANSI: 5
[ 11.457409] sd 5:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.489283] sd 6:0:0:0: [sdi] 234441648 512-byte logical blocks: (120 GB/112 GiB)
[ 11.489407] sd 6:0:0:0: [sdi] Write Protect is off
[ 11.489419] sd 6:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[ 11.489444] sd 6:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.489892] scsi 8:0:0:0: CD-ROM ASUS DRW-1814BL 1.14 PQ: 0 ANSI: 5
[ 11.490207] sdi: sdi1 sdi2
[ 11.490561] sd 6:0:0:0: [sdi] Attached SCSI disk
[ 11.498525] sdh: sdh1 sdh2 sdh3 sdh4
[ 11.498932] sd 5:0:0:0: [sdh] Attached SCSI disk
[ 11.519205] sr 8:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 11.519226] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 11.519942] sr 8:0:0:0: Attached scsi CD-ROM sr0
[ 11.524854] md: bind<sdi2>
[ 11.568599] device-mapper: uevent: version 1.0.3
[ 11.569257] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@xxxxxxxxxx
[ 11.570959] bcache: bch_journal_replay() journal replay done, 222 keys in 18 entries, seq 277165
[ 11.572529] bcache: register_cache() registered cache device sdi1
[ 11.665956] md: bind<sdg2>
[ 11.667876] md: raid1 personality registered for level 1
[ 11.668677] md/raid1:md127: active with 2 out of 2 mirrors
[ 11.669393] created bitmap (1 pages) for device md127
[ 11.670063] md127: bitmap initialized from disk: read 1 pages, set 0 of 1724 bits
[ 11.736285] md127: detected capacity change from 0 to 115670974464
[ 11.737148] md127: p1 p2 p3
[ 11.757297] bcache: register_bdev() registered backing device sdg1
[ 11.799462] bcache: bch_cached_dev_attach() Caching sdg1 as bcache0 on set 83bdeae1-6390-4435-ae29-c31616227bc7
[ 11.977678] random: crng init done
[ 12.452269] md: linear personality registered for level -1
[ 12.454108] md: multipath personality registered for level -4
[ 12.456055] md: raid0 personality registered for level 0
[ 12.569125] raid6: sse2x1 gen() 3834 MB/s
[ 12.637114] raid6: sse2x1 xor() 4277 MB/s
[ 12.705118] raid6: sse2x2 gen() 6483 MB/s
[ 12.773113] raid6: sse2x2 xor() 7282 MB/s
[ 12.841126] raid6: sse2x4 gen() 6869 MB/s
[ 12.909114] raid6: sse2x4 xor() 4560 MB/s
[ 12.909704] raid6: using algorithm sse2x4 gen() 6869 MB/s
[ 12.910293] raid6: .... xor() 4560 MB/s, rmw enabled
[ 12.910879] raid6: using intx1 recovery algorithm
[ 12.911670] xor: measuring software checksum speed
[ 12.949118] prefetch64-sse: 12256.000 MB/sec
[ 12.989118] generic_sse: 11646.000 MB/sec
[ 12.989702] xor: using function: prefetch64-sse (12256.000 MB/sec)
[ 12.990524] async_tx: api initialized (async)
[ 12.992379] md: raid6 personality registered for level 6
[ 12.993048] md: raid5 personality registered for level 5
[ 12.993642] md: raid4 personality registered for level 4
[ 12.997315] md: raid10 personality registered for level 10
[ 13.296939] Btrfs loaded, crc32c=crc32c-generic
[ 13.381140] blk_update_request: I/O error, dev fd0, sector 0
[ 13.381735] floppy: error -5 while reading block 0
[ 13.969467] BTRFS: device label home devid 1 transid 3289 /dev/md127p3
[ 13.970161] BTRFS: device label srv devid 2 transid 174 /dev/sdh3
[ 13.970845] BTRFS: device label srv devid 1 transid 174 /dev/sdg3
[ 13.973330] PM: Starting manual resume from disk
[ 13.973900] PM: Hibernation image partition 8:113 present
[ 13.973901] PM: Looking for hibernation image.
[ 13.974044] PM: Image not found (code -22)
[ 13.974045] PM: Hibernation image not present or could not be loaded.
[ 14.106664] EXT4-fs (md127p2): mounted filesystem with ordered data mode. Opts: (null)
[ 14.218213] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.222074] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 14.222750] systemd[1]: Detected architecture x86-64.
[ 14.225414] systemd[1]: Set hostname to <c21>.
[ 14.286478] systemd[1]: Listening on Journal Socket.
[ 14.287772] systemd[1]: Listening on udev Control Socket.
[ 14.289009] systemd[1]: Listening on Journal Audit Socket.
[ 14.290299] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 14.291525] systemd[1]: Listening on Journal Socket (/dev/log).
[ 14.292753] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 14.294089] systemd[1]: Created slice System Slice.
[ 14.306823] it87: Found IT8716F chip at 0x228, revision 0
[ 14.306844] it87: Beeping is supported
[ 14.316148] EXT4-fs (md127p2): re-mounted. Opts: errors=remount-ro
[ 14.402136] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
[ 14.402714] ACPI: Power Button [PWRB]
[ 14.403335] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[ 14.403916] ACPI: Power Button [PWRF]
[ 14.408675] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
[ 14.410139] acpi_cpufreq: overriding BIOS provided _PSD data
[ 14.416712] sd 10:0:0:0: Attached scsi generic sg0 type 0
[ 14.417708] sd 10:0:0:1: Attached scsi generic sg1 type 0
[ 14.418316] sd 11:0:0:0: Attached scsi generic sg2 type 0
[ 14.418928] sd 11:0:0:1: Attached scsi generic sg3 type 0
[ 14.419589] sd 1:0:0:0: Attached scsi generic sg4 type 0
[ 14.420408] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.421028] sd 2:0:0:0: Attached scsi generic sg5 type 0
[ 14.422592] sd 4:0:0:0: Attached scsi generic sg6 type 0
[ 14.423740] sd 5:0:0:0: Attached scsi generic sg7 type 0
[ 14.424411] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
[ 14.424697] sd 6:0:0:0: Attached scsi generic sg8 type 0
[ 14.424748] sr 8:0:0:0: Attached scsi generic sg9 type 5
[ 14.426300] sp5100_tco: PCI Vendor ID: 0x1002, Device ID: 0x4385, Revision ID: 0x14
[ 14.426871] sp5100_tco: failed to find MMIO address, giving up.
[ 14.459472] snd_hda_intel 0000:00:14.2: position_fix set to 1 for device 1458:a022
[ 14.460455] snd_hda_intel: probe of 0000:01:00.1 failed with error -2
[ 14.485265] snd_hda_codec_realtek hdaudioC0D3: autoconfig for ALC889A: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 14.485838] snd_hda_codec_realtek hdaudioC0D3: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 14.486396] snd_hda_codec_realtek hdaudioC0D3: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 14.486922] snd_hda_codec_realtek hdaudioC0D3: mono: mono_out=0x0
[ 14.487439] snd_hda_codec_realtek hdaudioC0D3: dig-out=0x1e/0x0
[ 14.487941] snd_hda_codec_realtek hdaudioC0D3: inputs:
[ 14.488439] snd_hda_codec_realtek hdaudioC0D3: Rear Mic=0x18
[ 14.488949] snd_hda_codec_realtek hdaudioC0D3: Front Mic=0x19
[ 14.489466] snd_hda_codec_realtek hdaudioC0D3: Line=0x1a
[ 14.489991] snd_hda_codec_realtek hdaudioC0D3: CD=0x1c
[ 14.490177] snd_ice1712 0000:06:07.0: Using board model TerraTec DMX6Fire
[ 14.490985] snd_hda_codec_realtek hdaudioC0D3: dig-in=0x1f
[ 14.507492] Bluetooth: Core ver 2.22
[ 14.508013] NET: Registered protocol family 31
[ 14.508493] Bluetooth: HCI device and connection manager initialized
[ 14.508968] Bluetooth: HCI socket layer initialized
[ 14.511338] Bluetooth: L2CAP socket layer initialized
[ 14.512165] Bluetooth: SCO socket layer initialized
[ 14.517683] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 14.521043] usbcore: registered new interface driver btusb
[ 14.530275] Bluetooth: hci0: BCM: chip id 63
[ 14.531835] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
[ 14.533937] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
[ 14.534503] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
[ 14.535073] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
[ 14.535638] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
[ 14.536246] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input12
[ 14.536800] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input13
[ 14.538790] bcache: register_bcache() error opening /dev/sdg1: device already registered
[ 14.549307] Bluetooth: hci0: c21
[ 14.551373] Bluetooth: hci0: BCM20702A1 (001.002.014) build 1338
[ 14.552780] bluetooth hci0: firmware: direct-loading firmware brcm/BCM20702A1-0a5c-21e8.hcd
[ 14.554066] kvm: Nested Virtualization enabled
[ 14.554590] kvm: Nested Paging enabled
[ 14.557603] EDAC MC: Ver: 3.0.0
[ 14.558989] bcache: register_bcache() error opening /dev/sdi1: device already registered
[ 14.560914] MCE: In-kernel MCE decoding enabled.
[ 14.562535] EDAC amd64: DRAM ECC disabled.
[ 14.563040] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 14.602687] ppdev: user-space parallel port driver
[ 14.603346] EDAC amd64: DRAM ECC disabled.
[ 14.603997] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 15.188907] Adding 16777212k swap on /dev/sdh1. Priority:-1 extents:1 across:16777212k FS
[ 15.347208] Bluetooth: hci0: BCM20702A1 (001.002.014) build 1338
[ 15.366194] Bluetooth: hci0: Broadcom Bluetooth Device
[ 15.389882] BTRFS info (device md127p3): use ssd allocation scheme
[ 15.390704] BTRFS info (device md127p3): use lzo compression
[ 15.390706] BTRFS info (device md127p3): disk space caching is enabled
[ 15.390707] BTRFS info (device md127p3): has skinny extents
[ 15.431388] EXT4-fs (bcache0): mounted filesystem with ordered data mode. Opts: (null)
[ 15.455247] systemd-journald[423]: Received request to flush runtime journal from PID 1
[ 15.456994] EXT4-fs (md127p1): mounted filesystem with ordered data mode. Opts: (null)
[ 15.549810] BTRFS info (device sdg3): disk space caching is enabled
[ 15.551856] BTRFS info (device sdg3): has skinny extents
[ 15.673919] EXT4-fs (sdh2): mounted filesystem without journal. Opts: (null)
[ 15.715252] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 15.756160] XFS (sdh4): Mounting V5 Filesystem
[ 15.887668] XFS (sdh4): Ending clean mount
[ 15.933906] r8169 0000:06:0f.0 enp6s15: link down
[ 15.935936] r8169 0000:06:0f.0 enp6s15: link down
[ 15.938010] IPv6: ADDRCONF(NETDEV_UP): enp6s15: link is not ready
[ 16.135146] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 16.135148] Bluetooth: BNEP filters: protocol multicast
[ 16.135156] Bluetooth: BNEP socket layer initialized
[ 19.335519] r8169 0000:06:0f.0 enp6s15: link up
[ 19.337439] IPv6: ADDRCONF(NETDEV_CHANGE): enp6s15: link becomes ready
[ 266.470363] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen
[ 266.472190] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data
[ 266.474022] ata2.00: failed command: READ FPDMA QUEUED
[ 266.475827] ata2.00: cmd 60/00:00:f0:bb:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in
res 60/00:00:f0:bb:0e/00:00:00:00:00/40 Emask 0x21 (host bus error)
[ 266.479401] ata2.00: status: { DRDY DF }
[ 266.481180] ata2.00: failed command: READ FPDMA QUEUED
[ 266.482964] ata2.00: cmd 60/00:08:f0:ba:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:40:10:40/00 Emask 0x20 (host bus error)
[ 266.486912] ata2.00: status: { DRDY }
[ 266.488711] ata2.00: error: { AMNF ABRT }
[ 266.490524] ata2: hard resetting link
[ 266.492295] ata2: controller in dubious state, performing PORT_RST
[ 268.693624] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 268.697455] ata2.00: configured for UDMA/100
[ 268.699297] ata2: EH complete
[ 268.834440] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen
[ 268.836245] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data
[ 268.838063] ata2.00: failed command: READ FPDMA QUEUED
[ 268.839843] ata2.00: cmd 60/00:00:f0:ba:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:40:00:40/00 Emask 0x20 (host bus error)
[ 268.843421] ata2.00: status: { DRDY }
[ 268.845213] ata2.00: error: { AMNF ABRT }
[ 268.847013] ata2.00: failed command: READ FPDMA QUEUED
[ 268.848794] ata2.00: cmd 60/00:08:f0:bb:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error)
[ 268.852416] ata2.00: status: { DRDY }
[ 268.854236] ata2.00: error: { AMNF ABRT }
[ 268.856027] ata2: hard resetting link
[ 268.857801] ata2: controller in dubious state, performing PORT_RST
[ 271.057626] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 271.061485] ata2.00: configured for UDMA/100
[ 271.063319] ata2: EH complete
[ 271.202443] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen
[ 271.204249] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data
[ 271.206073] ata2.00: failed command: READ FPDMA QUEUED
[ 271.207870] ata2.00: cmd 60/00:00:f0:bb:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:00:00:40/00 Emask 0x20 (host bus error)
[ 271.211530] ata2.00: status: { DRDY }
[ 271.213363] ata2.00: error: { AMNF ABRT }
[ 271.215189] ata2.00: failed command: READ FPDMA QUEUED
[ 271.217016] ata2.00: cmd 60/00:08:f0:ba:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error)
[ 271.220715] ata2.00: status: { DRDY }
[ 271.222581] ata2.00: error: { AMNF ABRT }
[ 271.224427] ata2: hard resetting link
[ 271.226281] ata2: controller in dubious state, performing PORT_RST
[ 273.425629] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 273.429528] ata2.00: configured for UDMA/100
[ 273.431416] ata2: EH complete
[ 273.566425] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen
[ 273.568314] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data
[ 273.570224] ata2.00: failed command: READ FPDMA QUEUED
[ 273.572099] ata2.00: cmd 60/00:00:f0:ba:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:40:00:40/00 Emask 0x20 (host bus error)
[ 273.575879] ata2.00: status: { DRDY }
[ 273.577806] ata2.00: error: { AMNF ABRT }
[ 273.580071] ata2.00: failed command: READ FPDMA QUEUED
[ 273.581984] ata2.00: cmd 60/00:08:f0:bb:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error)
[ 273.585815] ata2.00: status: { DRDY }
[ 273.587706] ata2.00: error: { AMNF ABRT }
[ 273.589596] ata2: hard resetting link
[ 273.591468] ata2: controller in dubious state, performing PORT_RST
[ 275.793629] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 275.797567] ata2.00: configured for UDMA/100
[ 275.799496] ata2: EH complete
[ 275.934436] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen
[ 275.936386] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data
[ 275.938361] ata2.00: failed command: READ FPDMA QUEUED
[ 275.940330] ata2.00: cmd 60/00:00:f0:bb:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:00:00:40/00 Emask 0x20 (host bus error)
[ 275.944329] ata2.00: status: { DRDY }
[ 275.946355] ata2.00: error: { AMNF ABRT }
[ 275.948346] ata2.00: failed command: READ FPDMA QUEUED
[ 275.950347] ata2.00: cmd 60/00:08:f0:ba:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error)
[ 275.954345] ata2.00: status: { DRDY }
[ 275.956330] ata2.00: error: { AMNF ABRT }
[ 275.958324] ata2: hard resetting link
[ 275.960284] ata2: controller in dubious state, performing PORT_RST
[ 278.161633] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 278.165627] ata2.00: configured for UDMA/100
[ 278.167609] ata2: EH complete
[ 278.310432] ata2.00: exception Emask 0x20 SAct 0x3 SErr 0x0 action 0x6 frozen
[ 278.312407] ata2.00: irq_stat 0x00020002, PCI master abort while transferring data
[ 278.314397] ata2.00: failed command: READ FPDMA QUEUED
[ 278.316365] ata2.00: cmd 60/00:00:f0:ba:0e/01:00:00:00:00/40 tag 0 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:40:00:40/00 Emask 0x20 (host bus error)
[ 278.320315] ata2.00: status: { DRDY }
[ 278.322304] ata2.00: error: { AMNF ABRT }
[ 278.324279] ata2.00: failed command: READ FPDMA QUEUED
[ 278.326268] ata2.00: cmd 60/00:08:f0:bb:0e/01:00:00:00:00/40 tag 1 ncq dma 131072 in
res 40/25:02:02:00:00/00:00:00:10:40/00 Emask 0x20 (host bus error)
[ 278.330242] ata2.00: status: { DRDY }
[ 278.332212] ata2.00: error: { AMNF ABRT }
[ 278.334178] ata2: hard resetting link
[ 278.336128] ata2: controller in dubious state, performing PORT_RST
[ 280.537636] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 280.541646] ata2.00: configured for UDMA/100
[ 280.543627] sd 1:0:0:0: [sde] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 280.545611] sd 1:0:0:0: [sde] tag#0 Sense Key : Medium Error [current]
[ 280.547567] sd 1:0:0:0: [sde] tag#0 Add. Sense: Address mark not found for data field
[ 280.549548] sd 1:0:0:0: [sde] tag#0 CDB: Read(10) 28 00 00 0e ba f0 00 01 00 00
[ 280.551517] blk_update_request: I/O error, dev sde, sector 965360
[ 280.553542] sd 1:0:0:0: [sde] tag#1 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 280.555901] sd 1:0:0:0: [sde] tag#1 Sense Key : Medium Error [current]
[ 280.557924] sd 1:0:0:0: [sde] tag#1 Add. Sense: Address mark not found for data field
[ 280.559928] sd 1:0:0:0: [sde] tag#1 CDB: Read(10) 28 00 00 0e bb f0 00 01 00 00
[ 280.561940] blk_update_request: I/O error, dev sde, sector 965616
[ 280.563961] ata2: EH complete
[ 8348.620026] ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
[ 8348.621645] ata1: irq_stat 0x00b40090, PHY RDY changed
[ 8348.623295] ata1: hard resetting link
[ 8358.626310] ata1: softreset failed (timeout)
[ 8358.627924] ata1: hard resetting link
[ 8361.391599] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 8361.393811] ata1.00: ATA-8: ST3000DM001-9YN166, CC4H, max UDMA/133
[ 8361.395466] ata1.00: 5860533168 sectors, multi 0: LBA48
[ 8361.397671] ata1.00: configured for UDMA/100
[ 8361.398342] ata1: EH complete
[ 8361.399205] scsi 0:0:0:0: Direct-Access ATA ST3000DM001-9YN1 CC4H PQ: 0 ANSI: 5
[ 8361.438676] sd 0:0:0:0: Attached scsi generic sg10 type 0
[ 8361.438689] sd 0:0:0:0: [sdj] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 8361.438694] sd 0:0:0:0: [sdj] 4096-byte physical blocks
[ 8361.438888] sd 0:0:0:0: [sdj] Write Protect is off
[ 8361.438896] sd 0:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 8361.438971] sd 0:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8361.487871] sdj: sdj1 sdj2
[ 8361.489045] sd 0:0:0:0: [sdj] Attached SCSI disk
[10562.688262] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10562.689701] ata1.00: irq_stat 0x00060002, PCI master abort while transferring data
[10562.691127] ata1.00: failed command: READ DMA
[10562.692609] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10562.695565] ata1.00: status: { Busy }
[10562.697060] ata1: hard resetting link
[10562.698547] ata1: controller in dubious state, performing PORT_RST
[10564.889203] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[10564.891970] ata1.00: configured for UDMA/100
[10564.893545] ata1: EH complete
[10565.028037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10565.029608] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10565.031207] ata1.00: failed command: READ DMA
[10565.032784] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10565.035952] ata1.00: status: { Busy }
[10565.037543] ata1: hard resetting link
[10565.039140] ata1: controller in dubious state, performing PORT_RST
[10567.228972] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[10567.231793] ata1.00: configured for UDMA/100
[10567.233456] ata1: EH complete
[10567.368096] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10567.369692] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10567.371315] ata1.00: failed command: READ DMA
[10567.372995] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10567.376224] ata1.00: status: { Busy }
[10567.377851] ata1: hard resetting link
[10567.379492] ata1: controller in dubious state, performing PORT_RST
[10569.568810] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[10569.571690] ata1.00: configured for UDMA/100
[10569.573371] ata1: EH complete
[10569.707698] ata1: limiting SATA link speed to 1.5 Gbps
[10569.709374] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10569.711087] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10569.712777] ata1.00: failed command: READ DMA
[10569.714466] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10569.717913] ata1.00: status: { Busy }
[10569.719683] ata1: hard resetting link
[10569.721770] ata1: controller in dubious state, performing PORT_RST
[10571.912619] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[10571.915665] ata1.00: configured for UDMA/100
[10571.917481] ata1: EH complete
[10572.051552] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10572.053372] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10572.055229] ata1.00: failed command: READ DMA
[10572.057046] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10572.060734] ata1.00: status: { Busy }
[10572.062609] ata1: hard resetting link
[10572.064484] ata1: controller in dubious state, performing PORT_RST
[10574.257205] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[10574.260335] ata1.00: configured for UDMA/100
[10574.262294] ata1: EH complete
[10574.399322] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10574.401276] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10574.403257] ata1.00: failed command: READ DMA
[10574.405205] ata1.00: cmd c8/00:00:e0:d3:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10574.409144] ata1.00: status: { Busy }
[10574.411542] ata1: hard resetting link
[10574.413555] ata1: controller in dubious state, performing PORT_RST
[10576.604232] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[10576.607520] ata1.00: configured for UDMA/100
[10576.609563] sd 0:0:0:0: [sdj] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[10576.611611] sd 0:0:0:0: [sdj] tag#0 Sense Key : Aborted Command [current]
[10576.613654] sd 0:0:0:0: [sdj] tag#0 Add. Sense: Scsi parity error
[10576.616047] sd 0:0:0:0: [sdj] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 d3 d3 e0 00 00 01 00 00 00
[10576.618148] blk_update_request: I/O error, dev sdj, sector 13882336
[10576.620285] ata1: EH complete
[10576.759123] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10576.761194] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10576.763277] ata1.00: failed command: READ DMA
[10576.765334] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10576.769458] ata1.00: status: { Busy }
[10576.771537] ata1: hard resetting link
[10576.773567] ata1: controller in dubious state, performing PORT_RST
[10578.964029] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[10578.967309] ata1.00: configured for UDMA/100
[10578.969352] ata1: EH complete
[10579.102837] ata1.00: limiting speed to UDMA/66:PIO4
[10579.104858] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10579.106911] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10579.108930] ata1.00: failed command: READ DMA
[10579.110962] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10579.115015] ata1.00: status: { Busy }
[10579.117024] ata1: hard resetting link
[10579.119025] ata1: controller in dubious state, performing PORT_RST
[10581.307818] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[10581.311119] ata1.00: configured for UDMA/66
[10581.313168] ata1: EH complete
[10581.450700] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10581.452739] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10581.454797] ata1.00: failed command: READ DMA
[10581.456811] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10581.460858] ata1.00: status: { Busy }
[10581.462922] ata1: hard resetting link
[10581.464926] ata1: controller in dubious state, performing PORT_RST
[10583.655637] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[10583.658911] ata1.00: configured for UDMA/66
[10583.660997] ata1: EH complete
[10583.794492] ata1.00: limiting speed to UDMA/33:PIO4
[10583.796511] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10583.798564] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10583.800583] ata1.00: failed command: READ DMA
[10583.802618] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10583.806679] ata1.00: status: { Busy }
[10583.809058] ata1: hard resetting link
[10583.811090] ata1: controller in dubious state, performing PORT_RST
[10585.999405] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[10586.002714] ata1.00: configured for UDMA/33
[10586.004761] ata1: EH complete
[10586.142263] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10586.144308] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10586.146368] ata1.00: failed command: READ DMA
[10586.148404] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10586.152495] ata1.00: status: { Busy }
[10586.154561] ata1: hard resetting link
[10586.156566] ata1: controller in dubious state, performing PORT_RST
[10588.347248] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[10588.350519] ata1.00: configured for UDMA/33
[10588.352550] ata1: EH complete
[10588.494107] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10588.496144] ata1.00: irq_stat 0x00020002, PCI master abort while transferring data
[10588.498202] ata1.00: failed command: READ DMA
[10588.500218] ata1.00: cmd c8/00:00:e0:d4:d3/00:00:00:00:00/e0 tag 0 dma 131072 in
res b8/20:02:02:00:00/00:00:00:00:b8/00 Emask 0x22 (host bus error)
[10588.504272] ata1.00: status: { Busy }
[10588.506335] ata1: hard resetting link
[10588.508342] ata1: controller in dubious state, performing PORT_RST
[10590.699055] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 10)
[10590.702324] ata1.00: configured for UDMA/33
[10590.704363] sd 0:0:0:0: [sdj] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[10590.706425] sd 0:0:0:0: [sdj] tag#0 Sense Key : Aborted Command [current]
[10590.708464] sd 0:0:0:0: [sdj] tag#0 Add. Sense: Scsi parity error
[10590.710512] sd 0:0:0:0: [sdj] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 d3 d4 e0 00 00 01 00 00 00
[10590.712560] blk_update_request: I/O error, dev sdj, sector 13882592
[10590.714663] ata1: EH complete
--- drivers/ata/sata_sil24.c.orig 2017-01-09 08:32:38.000000000 +0100
+++ drivers/ata/sata_sil24.c 2017-01-13 23:44:58.378675018 +0100
@@ -1313,15 +1313,4 @@
/* configure and activate the device */
- if (!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) {
- rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
- if (rc) {
- rc = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32));
- if (rc) {
- dev_err(&pdev->dev,
- "64-bit DMA enable failed\n");
- return rc;
- }
- }
- } else {
rc = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (rc) {
@@ -1335,5 +1324,4 @@
return rc;
}
- }
/* Set max read request size to 4096. This slightly increases
