Around Sun 24 Jan 2016 20:19:46 +0000 or thereabout, Måns Rullgård wrote: > Hans-Christian Noren Egtvedt <egtvedt@xxxxxxxxxxxx> writes: >> Around Sun 24 Jan 2016 19:21:50 +0000 or thereabout, Mans Rullgard wrote: >>> From: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx> >>> >>> The source and destination masters are reflecting buses or their layers to >>> where the different devices can be connected. The patch changes the master >>> names to reflect which one is related to which independently on the transfer >>> direction. >>> >>> The outcome of the change is that the memory data width is now always limited >>> by a data width of the master which is dedicated to communicate to memory. >>> >>> The patch will not break anything since all current users have the same data >>> width for all masters. Though it would be nice to revisit avr32 plaforms to >>> check what is the actual hardware topology is used there. It seems that it has >>> one bus and two masters on it as stated by Table 8-2, that's why everything >>> works independently on the master in use. The purpose of the sequential patch >>> is to fix the driver for configuration of more that one bus. >> >> Not entirely sure what you want to have confirmed here. There are multiple >> masters and slaves on the HMATRIX internal bus on AVR32, and the DMA >> controller supports up to three simultaneous configurations. >> >> Sounds good to support configuration of more than one bus. I thought we >> always did support that? Perhaps it was a non-standard avr32 implementation. > > The DW DMA controller on the AT32AP7000 serves the MCI, AC97, and ABDAC > peripherals. It appears to work regardless of the values put in the > various master select fields. Perhaps the topology is hardwired in the > DMA controller and those fields are ignored. The AVR32 works both > before and after this patch series, the main purpose of which (at least > my patches) is to fix the SATA driver on 460EX. DEST_PER and SRC_PER in the DMA controller selects this, numbers placed here should match the table you most likely found, 9-3. Wiring the handshake connections is done with the struct dw_dma_slave src_id or dst_id member, depending on data direction. Configured in the at32ap700x.c machine code. It is not hard wired on avr32, as there are not one-to-one configurations and masters. >>> The change is done in the assumption that src_master and dst_master are >>> reflecting a connection to the memory and peripheral correspondently on all >>> platforms except 460ex. OK, I have no knowledge about the 460ex. >>> Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx> >>> Signed-off-by: Mans Rullgard <mans@xxxxxxxxx> >> >> For the avr32 related stuff: >> >> Acked-by: Hans-Christian Egtvedt <egtvedt@xxxxxxxxxxxx> >> >>> --- >>> Documentation/devicetree/bindings/dma/snps-dma.txt | 4 ++-- >>> arch/avr32/mach-at32ap/at32ap700x.c | 16 ++++++++-------- >>> drivers/ata/sata_dwc_460ex.c | 4 ++-- >>> drivers/dma/dw/core.c | 15 +++++++-------- >>> drivers/dma/dw/platform.c | 12 ++++++------ >>> drivers/dma/dw/regs.h | 4 ++-- >>> drivers/spi/spi-pxa2xx-pci.c | 8 ++++---- >>> drivers/tty/serial/8250/8250_pci.c | 8 ++++---- >>> include/linux/platform_data/dma-dw.h | 8 ++++---- >>> 9 files changed, 39 insertions(+), 40 deletions(-) >> >> <snipp diff> -- Best regards, Hans-Christian Egtvedt -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
