Hi,
On Thursday 06 March 2014 04:13 AM, Loc Ho wrote:
This patch adds support for the APM X-Gene SoC 15Gbps Multi-purpose PHY.
This is the physical layer interface for the corresponding host
controller. Currently, only external clock and Gen3 SATA mode
are supported.
Signed-off-by: Loc Ho <lho@xxxxxxx>
Signed-off-by: Tuan Phan <tphan@xxxxxxx>
Signed-off-by: Suman Tripathi <stripathi@xxxxxxx>
---
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 2 +
drivers/phy/phy-xgene.c | 1756 +++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 1765 insertions(+), 0 deletions(-)
create mode 100644 drivers/phy/phy-xgene.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index afa2354..221a1b7 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -64,4 +64,11 @@ config BCM_KONA_USB2_PHY
help
Enable this to support the Broadcom Kona USB 2.0 PHY.
+config PHY_XGENE
+ tristate "APM X-Gene 15Gbps PHY support"
+ depends on HAS_IOMEM && OF && (ARM64 || COMPILE_TEST)
+ select GENERIC_PHY
+ help
+ This option enables support for APM X-Gene SoC multi-purpose PHY.
+
endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index b57c253..dee70f4 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -9,3 +9,5 @@ obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
+obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
+
.
.
<snip>
.
.
+ int i;
+
+ rc = xgene_phy_hw_initialize(ctx, CLK_EXT_DIFF, SSC_DISABLE);
+ if (rc) {
+ dev_err(ctx->dev, "PHY initialize failed %d\n", rc);
+ return rc;
+ }
+
+ /* Setup clock properly after PHY configuration */
+ if (!IS_ERR(ctx->clk)) {
+ /* HW requires an toggle of the clock */
+ clk_prepare_enable(ctx->clk);
+ clk_disable_unprepare(ctx->clk);
+ clk_prepare_enable(ctx->clk);
+ }
+
+ /* Compute average value */
+ for (i = 0; i < MAX_LANE; i++)
+ xgene_phy_gen_avg_val(ctx, i);
+
+ dev_dbg(ctx->dev, "PHY initialized\n");
+ return 0;
+}
+
+static const struct phy_ops xgene_phy_ops = {
+ .init = xgene_phy_hw_init,
+ .owner = THIS_MODULE,
+};
+
+static struct phy *xgene_phy_xlate(struct device *dev,
+ struct of_phandle_args *args)
+{
+ struct xgene_phy_ctx *ctx = dev_get_drvdata(dev);
+
+ if (args->args_count > 0) {
+ if (args->args[0] >= MODE_MAX)
+ return NULL;
Are you sure you want to return NULL instead of error? NULL is
considered a valid value for optional PHYs.
+ ctx->mode = args->args[0];
+ }
I think it doesn't make sense to return the phy without the 'mode'. So
we should report error here too.
+ return ctx->phy;
+}
+
+static void xgene_phy_get_param(struct platform_device *pdev,
+ const char *name, u32 *buffer,
+ int count, u32 *default_val,
+ u32 conv_factor)
+{
+ int i;
+
+ if (!of_property_read_u32_array(pdev->dev.of_node, name, buffer,
+ count)) {
+ for (i = 0; i < count; i++)
+ buffer[i] /= conv_factor;
+ return;
+ }
+ /* Does not exist, load default */
+ for (i = 0; i < count; i++)
+ buffer[i] = default_val[i % 3];
+}
+
+static int xgene_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct xgene_phy_ctx *ctx;
+ struct resource *res;
+ int rc = 0;
+ u32 default_spd[] = DEFAULT_SATA_SPD_SEL;
+ u32 default_txboost_gain[] = DEFAULT_SATA_TXBOOST_GAIN;
+ u32 default_txeye_direction[] = DEFAULT_SATA_TXEYEDIRECTION;
+ u32 default_txeye_tuning[] = DEFAULT_SATA_TXEYETUNING;
+ u32 default_txamp[] = DEFAULT_SATA_TXAMP;
+ u32 default_txcn1[] = DEFAULT_SATA_TXCN1;
+ u32 default_txcn2[] = DEFAULT_SATA_TXCN2;
+ u32 default_txcp1[] = DEFAULT_SATA_TXCP1;
+ int i;
+
+ ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx) {
+ dev_err(&pdev->dev, "can't allocate PHY context\n");
remove dev_err here.. kzalloc will do that for you..
+ return -ENOMEM;
+ }
+ ctx->dev = &pdev->dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "no PHY resource address\n");
same here.. you don't have to even check for return value of res.
ioremap_resource will take care of that.
+ rc = -EINVAL;
+ goto error;
+ }
+ ctx->sds_base = devm_ioremap_resource(&pdev->dev, res);
+ if (!ctx->sds_base) {
+ dev_err(&pdev->dev, "can't map PHY resource\n");
same here..
Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
