Re: [PATCH V4 5/8] SPEAr13xx: Fixup: Move SPEAr1340 SATA platform code to phy driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Thursday 06 February 2014 10:14 AM, Pratyush Anand wrote:
> ahci driver needs some platform specific functions which are called at
> init, exit, suspend and resume conditions. Till now these functions were
> present in a platform driver with a fixme notes.
> 
> Similar functions modifying same set of registers will also be needed in
> case of PCIe phy init/exit.
> 
> So move all these SATA platform code to phy-miphy40lp driver.
> 
> Signed-off-by: Pratyush Anand <pratyush.anand@xxxxxx>
> Tested-by: Mohit Kumar <mohit.kumar@xxxxxx>
> Cc: Viresh Kumar <viresh.linux@xxxxxxxxx>
> Cc: Tejun Heo <tj@xxxxxxxxxx>
> Cc: Arnd Bergmann <arnd@xxxxxxxx>
> Cc: Kishon Vijay Abraham I <kishon@xxxxxx>
> Cc: spear-devel@xxxxxxxxxxx
> Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> Cc: devicetree@xxxxxxxxxxxxxxx
> Cc: linux-ide@xxxxxxxxxxxxxxx
> Cc: linux-kernel@xxxxxxxxxxxxxxx
> ---
>  .../devicetree/bindings/arm/spear-misc.txt         |   4 +
>  arch/arm/boot/dts/spear1310-evb.dts                |   4 +
>  arch/arm/boot/dts/spear1310.dtsi                   |  39 +++-
>  arch/arm/boot/dts/spear1340-evb.dts                |   4 +
>  arch/arm/boot/dts/spear1340.dtsi                   |  13 +-
>  arch/arm/boot/dts/spear13xx.dtsi                   |   5 +
>  arch/arm/mach-spear/Kconfig                        |   2 +
>  arch/arm/mach-spear/spear1340.c                    | 127 +------------
>  drivers/phy/phy-miphy40lp.c                        | 204 ++++++++++++++++++++-

It would be better if you can split this patch. Keep arch/ in separate patch
and drivers/ in separate patch.
>  9 files changed, 266 insertions(+), 136 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/arm/spear-misc.txt
> 
.
.
<snip>
.
.
>  static const char * const spear1340_dt_board_compat[] = {
> diff --git a/drivers/phy/phy-miphy40lp.c b/drivers/phy/phy-miphy40lp.c
> index d478c14..cc7f45d 100644
> --- a/drivers/phy/phy-miphy40lp.c
> +++ b/drivers/phy/phy-miphy40lp.c
> @@ -8,6 +8,7 @@
>   * it under the terms of the GNU General Public License version 2 as
>   * published by the Free Software Foundation.
>   *
> + * 04/02/2014: Adding support of SATA mode for SPEAr1340.
>   */
>  
>  #include <linux/delay.h>
> @@ -19,6 +20,60 @@
>  #include <linux/phy/phy.h>
>  #include <linux/regmap.h>
>  
> +/* SPEAr1340 Registers */
> +/* Power Management Registers */
> +#define SPEAR1340_PCM_CFG			0x100
> +	#define SPEAR1340_PCM_CFG_SATA_POWER_EN	0x800
> +#define SPEAR1340_PCM_WKUP_CFG			0x104
> +#define SPEAR1340_SWITCH_CTR			0x108
> +
> +#define SPEAR1340_PERIP1_SW_RST			0x318
> +	#define SPEAR1340_PERIP1_SW_RST_SATA	0x1000
> +#define SPEAR1340_PERIP2_SW_RST			0x31C
> +#define SPEAR1340_PERIP3_SW_RST			0x320
> +
> +/* PCIE - SATA configuration registers */
> +#define SPEAR1340_PCIE_SATA_CFG			0x424
> +	/* PCIE CFG MASks */
> +	#define SPEAR1340_PCIE_CFG_DEVICE_PRESENT	(1 << 11)

use BIT() wherever possible.
> +	#define SPEAR1340_PCIE_CFG_POWERUP_RESET	(1 << 10)
> +	#define SPEAR1340_PCIE_CFG_CORE_CLK_EN		(1 << 9)
> +	#define SPEAR1340_PCIE_CFG_AUX_CLK_EN		(1 << 8)
> +	#define SPEAR1340_SATA_CFG_TX_CLK_EN		(1 << 4)
> +	#define SPEAR1340_SATA_CFG_RX_CLK_EN		(1 << 3)
> +	#define SPEAR1340_SATA_CFG_POWERUP_RESET	(1 << 2)
> +	#define SPEAR1340_SATA_CFG_PM_CLK_EN		(1 << 1)
> +	#define SPEAR1340_PCIE_SATA_SEL_PCIE		(0)
> +	#define SPEAR1340_PCIE_SATA_SEL_SATA		(1)
> +	#define SPEAR1340_PCIE_SATA_CFG_MASK		0xF1F
> +	#define SPEAR1340_PCIE_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_PCIE | \
> +			SPEAR1340_PCIE_CFG_AUX_CLK_EN | \
> +			SPEAR1340_PCIE_CFG_CORE_CLK_EN | \
> +			SPEAR1340_PCIE_CFG_POWERUP_RESET | \
> +			SPEAR1340_PCIE_CFG_DEVICE_PRESENT)
> +	#define SPEAR1340_SATA_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_SATA | \
> +			SPEAR1340_SATA_CFG_PM_CLK_EN | \
> +			SPEAR1340_SATA_CFG_POWERUP_RESET | \
> +			SPEAR1340_SATA_CFG_RX_CLK_EN | \
> +			SPEAR1340_SATA_CFG_TX_CLK_EN)
> +
> +#define SPEAR1340_PCIE_MIPHY_CFG		0x428
> +	#define SPEAR1340_MIPHY_OSC_BYPASS_EXT		(1 << 31)
> +	#define SPEAR1340_MIPHY_CLK_REF_DIV2		(1 << 27)
> +	#define SPEAR1340_MIPHY_CLK_REF_DIV4		(2 << 27)
> +	#define SPEAR1340_MIPHY_CLK_REF_DIV8		(3 << 27)
> +	#define SPEAR1340_MIPHY_PLL_RATIO_TOP(x)	(x << 0)
> +	#define SPEAR1340_PCIE_MIPHY_CFG_MASK		0xF80000FF
> +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \
> +			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
> +			SPEAR1340_MIPHY_CLK_REF_DIV2 | \
> +			SPEAR1340_MIPHY_PLL_RATIO_TOP(60))
> +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
> +			(SPEAR1340_MIPHY_PLL_RATIO_TOP(120))
> +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \
> +			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
> +			SPEAR1340_MIPHY_PLL_RATIO_TOP(25))
> +
>  enum phy_mode {
>  	SATA,
>  	PCIE,
> @@ -38,28 +93,145 @@ struct st_miphy40lp_priv {
>  	u32			id;
>  };
>  
> +static int spear1340_sata_miphy_init(struct st_miphy40lp_priv *phypriv)

The function name format here differs from what you have already added. It will
be good to have consistent name in the file.
> +{
> +	regmap_update_bits(phypriv->misc, SPEAR1340_PCIE_SATA_CFG,
> +			SPEAR1340_PCIE_SATA_CFG_MASK, SPEAR1340_SATA_CFG_VAL);
> +	regmap_update_bits(phypriv->misc, SPEAR1340_PCIE_MIPHY_CFG,
> +			SPEAR1340_PCIE_MIPHY_CFG_MASK,
> +			SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK);
> +	/* Switch on sata power domain */
> +	regmap_update_bits(phypriv->misc, SPEAR1340_PCM_CFG,
> +			SPEAR1340_PCM_CFG_SATA_POWER_EN,
> +			SPEAR1340_PCM_CFG_SATA_POWER_EN);
> +	msleep(20);
> +	/* Disable PCIE SATA Controller reset */
> +	regmap_update_bits(phypriv->misc, SPEAR1340_PERIP1_SW_RST,
> +			SPEAR1340_PERIP1_SW_RST_SATA, 0);
> +	msleep(20);
> +
> +	return 0;
> +}
> +
> +static int spear1340_sata_miphy_exit(struct st_miphy40lp_priv *phypriv)
> +{
> +	regmap_update_bits(phypriv->misc, SPEAR1340_PCIE_SATA_CFG,
> +			SPEAR1340_PCIE_SATA_CFG_MASK, 0);
> +	regmap_update_bits(phypriv->misc, SPEAR1340_PCIE_MIPHY_CFG,
> +			SPEAR1340_PCIE_MIPHY_CFG_MASK, 0);
> +
> +	/* Enable PCIE SATA Controller reset */
> +	regmap_update_bits(phypriv->misc, SPEAR1340_PERIP1_SW_RST,
> +			SPEAR1340_PERIP1_SW_RST_SATA,
> +			SPEAR1340_PERIP1_SW_RST_SATA);
> +	msleep(20);
> +	/* Switch off sata power domain */
> +	regmap_update_bits(phypriv->misc, SPEAR1340_PCM_CFG,
> +			SPEAR1340_PCM_CFG_SATA_POWER_EN, 0);
> +	msleep(20);
> +
> +	return 0;
> +}
> +
> +static int sata_miphy_init(struct st_miphy40lp_priv *phypriv)
> +{
> +	if (of_device_is_compatible(phypriv->np, "st,spear1340-miphy"))

This compatible value is a bit confusing since it doesn't have 'sata' in it.
spear1340 can have usb phy or pcie phy too no? How do we differentiate it then?
> +		return spear1340_sata_miphy_init(phypriv);
> +	else
> +		return -EINVAL;
> +}
> +
> +static int sata_miphy_exit(struct st_miphy40lp_priv *phypriv)
> +{
> +	if (of_device_is_compatible(phypriv->np, "st,spear1340-miphy"))
> +		return spear1340_sata_miphy_exit(phypriv);
> +	else
> +		return -EINVAL;
> +}
> +
> +static int sata_miphy_power_off(struct st_miphy40lp_priv *phypriv)
> +{
> +	if (of_device_is_compatible(phypriv->np, "st,spear1340-miphy"))
> +		return 0;
> +	else
> +		return -EINVAL;
> +}
> +
> +static int sata_miphy_power_on(struct st_miphy40lp_priv *phypriv)
> +{
> +	if (of_device_is_compatible(phypriv->np, "st,spear1340-miphy"))
> +		return 0;
> +	else
> +		return -EINVAL;
> +}
> +
> +static int sata_miphy_suspend(struct st_miphy40lp_priv *phypriv)
> +{
> +	if (of_device_is_compatible(phypriv->np, "st,spear1340-miphy"))
> +		return spear1340_sata_miphy_exit(phypriv);
> +	else
> +		return -EINVAL;
> +}
> +
> +static int sata_miphy_resume(struct st_miphy40lp_priv *phypriv)
> +{
> +	if (of_device_is_compatible(phypriv->np, "st,spear1340-miphy"))
> +		return spear1340_sata_miphy_init(phypriv);
> +	else
> +		return -EINVAL;
> +}
> +
>  static int miphy40lp_init(struct phy *phy)
>  {
> -	return -EINVAL;
> +	struct st_miphy40lp_priv *phypriv = phy_get_drvdata(phy);
> +
> +	switch (phypriv->mode) {
> +	case SATA:
> +		return sata_miphy_init(phypriv);
> +	default:
> +		return -EINVAL;
> +	}
>  }
>  
>  static int miphy40lp_exit(struct phy *phy)
>  {
> -	return -EINVAL;
> +	struct st_miphy40lp_priv *phypriv = phy_get_drvdata(phy);
> +
> +	switch (phypriv->mode) {
> +	case SATA:
> +		return sata_miphy_exit(phypriv);
> +	default:
> +		return -EINVAL;
> +	}
>  }
>  
>  static int miphy40lp_power_off(struct phy *phy)
>  {
> -	return -EINVAL;
> +	struct st_miphy40lp_priv *phypriv = phy_get_drvdata(phy);
> +
> +	switch (phypriv->mode) {
> +	case SATA:
> +		return sata_miphy_power_off(phypriv);
> +	default:
> +		return -EINVAL;
> +	}
>  }
>  
>  static int miphy40lp_power_on(struct phy *phy)
>  {
> -	return -EINVAL;
> +	struct st_miphy40lp_priv *phypriv = phy_get_drvdata(phy);
> +
> +	switch (phypriv->mode) {
> +	case SATA:
> +		return sata_miphy_power_on(phypriv);
> +	default:
> +		return -EINVAL;
> +	}
>  }
>  
>  static const struct of_device_id st_miphy40lp_of_match[] = {
>  	{ .compatible = "st,miphy40lp-phy" },
> +	{ .compatible = "st,spear1340-miphy" },
>  	{ },
>  };
>  MODULE_DEVICE_TABLE(of, st_miphy40lp_of_match);
> @@ -75,12 +247,32 @@ static struct phy_ops st_miphy40lp_ops = {
>  #ifdef CONFIG_PM_SLEEP
>  static int miphy40lp_suspend(struct device *dev)
>  {
> -	return -EINVAL;
> +	struct st_miphy40lp_priv *phypriv = dev_get_drvdata(dev);
> +
> +	if (dev->power.power_state.event == PM_EVENT_FREEZE)
> +		return 0;

I'm not sure if you should be accessing it from the drivers. Will be good to
check with PM guys.
> +
> +	switch (phypriv->mode) {
> +	case SATA:
> +		return sata_miphy_suspend(phypriv);
> +	default:
> +		return -EINVAL;
> +	}
>  }
>  
>  static int miphy40lp_resume(struct device *dev)
>  {
> -	return -EINVAL;
> +	struct st_miphy40lp_priv *phypriv = dev_get_drvdata(dev);
> +
> +	if (dev->power.power_state.event == PM_EVENT_THAW)
> +		return 0;

Same here.

Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux