Hi,
On 01/31/2014 02:45 PM, Maxime Ripard wrote:
Hi Hans,
On Wed, Jan 22, 2014 at 08:04:48PM +0100, Hans de Goede wrote:
From: Oliver Schinagl <oliver@xxxxxxxxxxx>
This patch adds sunxi sata support to A10 boards that have such a connector.
Some boards also feature a regulator via a GPIO and support for this is also
added.
Signed-off-by: Olliver Schinagl <oliver@xxxxxxxxxxx>
Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
---
arch/arm/boot/dts/sun4i-a10-a1000.dts | 4 ++++
arch/arm/boot/dts/sun4i-a10-cubieboard.dts | 6 +++++
arch/arm/boot/dts/sun4i-a10.dtsi | 8 +++++++
arch/arm/boot/dts/sunxi-ahci-reg.dtsi | 38 ++++++++++++++++++++++++++++++
I'm still half convinced about this at the moment, given the number of
platforms we support, we can always change it back if things become too messy.
I assume that this == sunxi-ahci-reg.dtsi ? To be sure I understand you correctly,
you're ok with going this route for now, right ?
How about the same for the usb ohci/ehci controller dts patches ? Currently they
are still using the put a regulator node in each dts file model, which leads to
a lot of boilerplate code. So I would like to move to the same model as I'm
using here for the sata supply.
4 files changed, 56 insertions(+)
create mode 100644 arch/arm/boot/dts/sunxi-ahci-reg.dtsi
diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/sun4i-a10-a1000.dts
index aef8207..3fb7305 100644
--- a/arch/arm/boot/dts/sun4i-a10-a1000.dts
+++ b/arch/arm/boot/dts/sun4i-a10-a1000.dts
@@ -48,6 +48,10 @@
status = "okay";
};
+ ahci: sata@01c18000 {
+ status = "okay";
+ };
+
pinctrl@01c20800 {
mmc0_cd_pin_a1000: mmc0_cd_pin@0 {
allwinner,pins = "PH1";
diff --git a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
index f50fb2b..6ae1110 100644
--- a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
+++ b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
@@ -12,6 +12,7 @@
/dts-v1/;
/include/ "sun4i-a10.dtsi"
+/include/ "sunxi-ahci-reg.dtsi"
/ {
model = "Cubietech Cubieboard";
@@ -51,6 +52,11 @@
status = "okay";
};
+ ahci: sata@01c18000 {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+ };
+
pinctrl@01c20800 {
mmc0_cd_pin_cubieboard: mmc0_cd_pin@0 {
allwinner,pins = "PH1";
diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi
index 4736dd2..198dcda 100644
--- a/arch/arm/boot/dts/sun4i-a10.dtsi
+++ b/arch/arm/boot/dts/sun4i-a10.dtsi
@@ -331,6 +331,14 @@
status = "disabled";
};
+ ahci: sata@01c18000 {
+ compatible = "allwinner,sun4i-a10-ahci";
To be consistent with the rest of the sun4i devices compatible, It
should be sun4i-ahci.
However, since these devices don't use the same compatible pattern as
their own machine compatible, and are consisent with the rest of the
compatibles for the other SoCs, we can probably make this a go to
transition progressively to this pattern.
Ack, I think it would be good to be consistent and try to use
sun?i-aXX-foo everywhere. I noticed that we already use that in various
places, so I thought it would be good to do that for all new dts bindings.
I'll cook up some patches for the other devices.
Thanks.
+ reg = <0x01c18000 0x1000>;
+ interrupts = <56>;
+ clocks = <&pll6 0>, <&ahb_gates 25>;
+ status = "disabled";
+ };
+
intc: interrupt-controller@01c20400 {
compatible = "allwinner,sun4i-ic";
reg = <0x01c20400 0x400>;
diff --git a/arch/arm/boot/dts/sunxi-ahci-reg.dtsi b/arch/arm/boot/dts/sunxi-ahci-reg.dtsi
new file mode 100644
index 0000000..955b197
--- /dev/null
+++ b/arch/arm/boot/dts/sunxi-ahci-reg.dtsi
@@ -0,0 +1,38 @@
+/*
+ * sunxi boards sata target power supply common code
+ *
+ * Copyright 2014 - Hans de Goede <hdegoede@xxxxxxxxxx>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/ {
+ soc@01c00000 {
+ ahci_pwr_pin_a: ahci_pwr_pin@0 {
+ allwinner,pins = "PB8";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
This should be under the pinctrl node.
Fixed already locally.
Regards,
Hans
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
