Re: SATA hotplug not detecting new disks

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 07/26/2013 07:15 AM, Dave Hansen wrote:
> I've got a relatively new system that doesn't seem to be able to hotplug
> SATA disks.  I see the same behavior on 3.10, 3.11-rc2, and Ubuntu's
> 3.8.0-25-generic.  The disks are detected right away on reboots, but
> even after poking the /sys/class/scsi_host/host*/scan files, new disks
> are never detected.  I've disabled link power management.
> 
> Am I doing something stupid here?  I thought this "just worked" on my
> previous hardware.

My vague memory reminds me that not all SATA ports are hot pluggable -
you can check the port's "External SATA port" bit and "Hot Plug Capable"
bit of the PxCMD register like this:

$ grep ahci /proc/iomem 
    e1a40000-e1a407ff : ahci
# dd if=/dev/mem of=ahcidump bs=4096 count=1 skip=0xe1a40
You will need to change 0xe1a40 to decimal format.

Then the PxCMD is at offset 0x118 for port 0, check bit 21 for E-SATA or
bit 18 for hot pluggable bits. If any of them set to 1, this port
should be hot pluggable; otherwise, it doesn't have this capability.

> 
> The motherboard is an Intel DH87RL. The SATA controller is:
> 
>> 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0])
>> 	Subsystem: Intel Corporation Device 204a
>> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
>> 	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>> 	Latency: 0
>> 	Interrupt: pin B routed to IRQ 41
>> 	Region 0: I/O ports at f0d0 [size=8]
>> 	Region 1: I/O ports at f0c0 [size=4]
>> 	Region 2: I/O ports at f0b0 [size=8]
>> 	Region 3: I/O ports at f0a0 [size=4]
>> 	Region 4: I/O ports at f060 [size=32]
>> 	Region 5: Memory at f7d3a000 (32-bit, non-prefetchable) [size=2K]
>> 	Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
>> 		Address: fee2200c  Data: 4191
>> 	Capabilities: [70] Power Management version 3
>> 		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
>> 		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
>> 	Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
>> 	Kernel driver in use: ahci
> 
> Relevant dmesg from boot:
> 
> ahci 0000:00:1f.2: version 3.0
> ahci 0000:00:1f.2: irq 41 for MSI/MSI-X
> ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 5 ports 6 Gbps 0x1e impl SATA
> mode
> ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst

This doesn't have sxs(support external sata) bit here, so no ports from
this host is E-SATA port. Only need to check the hot pluggable bit.

Hope this helps,
-Aaron

> ahci 0000:00:1f.2: setting latency timer to 64
> scsi0 : ahci
> scsi1 : ahci
> scsi2 : ahci
> scsi3 : ahci
> scsi4 : ahci
> ata1: DUMMY
> ata2: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a180 irq 41
> ata3: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a200 irq 41
> ata4: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a280 irq 41
> ata5: SATA max UDMA/133 abar m2048@0xf7d3a000 port 0xf7d3a300 irq 41
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux