Hi Hector, I don't have this issue either. Could you verify it's caused by something else? You may try a different SSD. - eric On Wed, Aug 31, 2011 at 8:09 PM, Richard Zhu <richard.zhu@xxxxxxxxxx> wrote: > Hi Hector: > What's happen before "> [ 7.073106] EXT4-fs (sda2): re-mounted. > Opts: errors=remount-ro"? > I re-based the patches to Sascha's imx-features branch, my sata device can work. > Test sw environment: Sascha's imx-features branch, > Test hw environment: iMX53 loco board, 32G sandisk ssd, tftp download > the kernel image, > and the nfs type rootfs is mounted. > > loop: module loaded > ahci: SSS flag set, parallel bus scan disabled > ahci imx53-ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode > ahci imx53-ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc > scsi0 : ahci_platform > ata1: SATA max UDMA/133 mmio [mem 0x10000000-0x10000fff] port 0x100 irq 28 > FEC Ethernet Driver > fec_enet_mii_bus: probed > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > mousedev: PS/2 mouse device common for all mice > input: mma8450 as /devices/virtual/input/input0 > i2c /dev entries driver > imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0) > sdhci: Secure Digital Host Controller Interface driver > sdhci: Copyright(c) Pierre Ossman > sdhci-pltfm: SDHCI platform and OF driver helper > mmc0: no vmmc regulator found > mmc0: SDHCI controller on sdhci-esdhc-imx53.0 [sdhci-esdhc-imx53.0] using DMA > mmc1: no vmmc regulator found > mmc1: SDHCI controller on sdhci-esdhc-imx53.2 [sdhci-esdhc-imx53.2] using DMA > usbcore: registered new interface driver usbhid > usbhid: USB HID core driver > TCP cubic registered > NET: Registered protocol family 17 > Registering the dns_resolver key type > VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 > input: gpio-keys as /devices/platform/gpio-keys/input/input1 > drivers/rtc/hctosys.c: unable to open rtc device (rtc0) > eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] > (mii_bus:phy_addr=1:00, irq=-1) > mmc0: host does not support reading read-only switch. assuming write-enable. > mmc0: new high speed SDHC card at address 0001 > mmcblk0: mmc0:0001 00000 3.79 GiB > mmcblk0: p1 p2 p3 > ata1: softreset failed (device not ready) > ata1: applying PMP SRST workaround and retrying > ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > ata1.00: ATA-8: SanDisk SSD P4 32GB, SSD 8.00, max UDMA/133 > ata1.00: 62533296 sectors, multi 1: LBA48 > ata1.00: configured for UDMA/133 > scsi 0:0:0:0: Direct-Access ATA SanDisk SSD P4 3 SSD PQ: 0 ANSI: 5 > sd 0:0:0:0: [sda] 62533296 512-byte logical blocks: (32.0 GB/29.8 GiB) > sd 0:0:0:0: [sda] Write Protect is off > sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sda: sda1 sda2 > sd 0:0:0:0: [sda] Attached SCSI disk > PHY: 1:00 - Link is Up - 100/Full > Sending DHCP requests ., OK > > Best Regards > Richard Zhu > > On 31 August 2011 20:57, Hector Oron <hector.oron@xxxxxxxxx> wrote: >> Hello, >> >> 2011/8/31 Richard Zhu <richard.zhu@xxxxxxxxxx>: >>> Hi Hector: >>> Thanks for your help to tests these patches. >> >> Note I rebased this patches against 'imx-features' branch on Sascha's tree. >> I am noticing some obscure (to me) messages from kernel: >> >> [ 6.874694] Adding 9767516k swap on /dev/sda3. Priority:-1 >> extents:1 across:9767516k >> [ 7.073106] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro >> [ 7.708399] ata1.00: exception Emask 0x12 SAct 0x3 SErr 0x1280500 >> action 0x6 frozen >> [ 7.716219] ata1.00: irq_stat 0x08000000, interface fatal error >> [ 7.722216] ata1: SError: { UnrecovData Proto 10B8B BadCRC TrStaTrns } >> [ 7.728780] ata1.00: failed command: READ FPDMA QUEUED >> [ 7.733995] ata1.00: cmd 60/00:00:f2:11:32/01:00:00:00:00/40 tag 0 >> ncq 131072 in >> [ 7.734002] res 40/00:04:f2:11:32/00:00:00:00:00/40 Emask >> 0x12 (ATA bus error) >> [ 7.749468] ata1.00: status: { DRDY } >> [ 7.753176] ata1.00: failed command: READ FPDMA QUEUED >> [ 7.758356] ata1.00: cmd 60/18:08:c2:14:32/00:00:00:00:00/40 tag 1 >> ncq 12288 in >> [ 7.758363] res 40/00:04:f2:11:32/00:00:00:00:00/40 Emask >> 0x12 (ATA bus error) >> [ 7.773739] ata1.00: status: { DRDY } >> [ 7.777448] ata1: hard resetting link >> [ 8.750427] ata1: softreset failed (device not ready) >> [ 8.755551] ata1: applying PMP SRST workaround and retrying >> [ 8.960435] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >> [ 8.981938] ata1.00: configured for UDMA/133 >> [ 8.986535] ata1: EH complete >> [ 12.147912] eth0: Freescale FEC PHY driver [Generic PHY] >> (mii_bus:phy_addr=1:00, irq=-1) >> [ 12.521870] ata1.00: exception Emask 0x12 SAct 0xf SErr 0x800500 >> action 0x6 frozen >> [ 12.529518] ata1.00: irq_stat 0x08000000, interface fatal error >> [ 12.535546] ata1: SError: { UnrecovData Proto LinkSeq } >> [ 12.540851] ata1.00: failed command: READ FPDMA QUEUED >> [ 12.546039] ata1.00: cmd 60/00:00:a2:19:2c/01:00:00:00:00/40 tag 0 >> ncq 131072 in >> [ 12.546046] res 40/00:14:7a:aa:2c/00:00:00:00:00/40 Emask >> 0x12 (ATA bus error) >> [ 12.561519] ata1.00: status: { DRDY } >> [ 12.565209] ata1.00: failed command: READ FPDMA QUEUED >> [ 12.570419] ata1.00: cmd 60/00:08:1a:e9:2c/01:00:00:00:00/40 tag 1 >> ncq 131072 in >> [ 12.570426] res 40/00:14:7a:aa:2c/00:00:00:00:00/40 Emask >> 0x12 (ATA bus error) >> [ 12.585890] ata1.00: status: { DRDY } >> [ 12.589578] ata1.00: failed command: READ FPDMA QUEUED >> [ 12.594776] ata1.00: cmd 60/00:10:7a:aa:2c/01:00:00:00:00/40 tag 2 >> ncq 131072 in >> [ 12.594783] res 40/00:14:7a:aa:2c/00:00:00:00:00/40 Emask >> 0x12 (ATA bus error) >> [ 12.610240] ata1.00: status: { DRDY } >> [ 12.613945] ata1.00: failed command: READ FPDMA QUEUED >> [ 12.619118] ata1.00: cmd 60/e0:18:1a:10:2c/00:00:00:00:00/40 tag 3 >> ncq 114688 in >> [ 12.619125] res 40/00:14:7a:aa:2c/00:00:00:00:00/40 Emask >> 0x12 (ATA bus error) >> [ 12.634583] ata1.00: status: { DRDY } >> [ 12.638292] ata1: hard resetting link >> [ 13.790424] ata1: softreset failed (device not ready) >> [ 13.795543] ata1: applying PMP SRST workaround and retrying >> [ 14.000437] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) >> [ 14.021749] ata1.00: configured for UDMA/133 >> [ 14.026836] ata1: EH complete >> [ 14.140774] PHY: 1:00 - Link is Up - 100/Full >> >> >> Best regards, >> -- >> Héctor Orón -.. . -... .. .- -. -.. . ...- . .-.. --- .--. . .-. >> > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel > -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html