Hi,
We have an x86 system based on the VortexDX SoC with RDC IDE
controller that supports up to UDMA2 IDE speeds. Whenever a Compact
Flash is present on the IDE controller, I get the following ATA error
handling messages before the IDE Linux kernel driver (pata_rdc.ko)
finally settles down (after almost a minute or so) to PIO4 speed for
the Compact Flash:
[ 37.827489] ata1: lost interrupt (Status 0x58)
[ 37.827910] ata1: drained 512 bytes to clear DRQ.
[ 37.827961] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 37.828060] ata1.01: failed command: READ DMA
[ 37.828162] ata1.01: cmd c8/00:08:00:00:00/00:00:00:00:00/f0 tag 0
dma 4096 in
[ 37.828176] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 37.828311] ata1.01: status: { DRDY }
[ 37.828452] ata1: soft resetting link
[ 38.280580] ata1.00: configured for UDMA/33
[ 38.287670] ata1.01: configured for MWDMA2
[ 38.287707] ata1.01: device reported invalid CHS sector 0
[ 38.287753] ata1: EH complete
[ 68.834877] ata1: lost interrupt (Status 0x58)
[ 68.835285] ata1: drained 512 bytes to clear DRQ.
[ 68.835323] ata1.01: limiting speed to MWDMA1:PIO4
[ 68.835354] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 68.835448] ata1.01: failed command: READ DMA
[ 68.835548] ata1.01: cmd c8/00:08:00:00:00/00:00:00:00:00/f0 tag 0
dma 4096 in
[ 68.835562] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 68.835698] ata1.01: status: { DRDY }
[ 68.835827] ata1: soft resetting link
[ 69.295660] ata1.00: configured for UDMA/33
[ 69.303102] ata1.01: configured for MWDMA1
[ 69.303134] ata1.01: device reported invalid CHS sector 0
[ 69.303175] ata1: EH complete
[ 99.874284] ata1: lost interrupt (Status 0x58)
[ 99.874784] ata1: drained 512 bytes to clear DRQ.
[ 99.874819] ata1.01: limiting speed to PIO4
[ 99.874849] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 99.874941] ata1.01: failed command: READ DMA
[ 99.875041] ata1.01: cmd c8/00:08:00:00:00/00:00:00:00:00/f0 tag 0
dma 4096 in
[ 99.875055] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
0x4 (timeout)
[ 99.875191] ata1.01: status: { DRDY }
[ 99.875319] ata1: soft resetting link
[ 100.334769] ata1.00: configured for UDMA/33
[ 100.342485] ata1.01: configured for PIO4
[ 100.342515] ata1.01: device reported invalid CHS sector 0
[ 100.342556] ata1: EH complete
[ 100.344624] sdb: sdb1
[ 100.351473] sd 0:0:0:0: [sda] Attached SCSI disk
[ 100.352914] sdb: detected capacity change from 0 to 521773056
[ 100.355713] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 100.368940] sdb: detected capacity change from 0 to 521773056
Attached is the dmesg and lspci -vvvxxx output of the system with Hard
drive (as Primary Master) and Compact Flash (Primary Slave). Note that
the BIOS correctly identifies the max supported speeds for the IDE
devices (UMDA2 for Hard Drive and MWDMA2 for Compact Flash) in the
CMOS.
Thanks.
Kushal Koolwal
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.39-2-486 (Debian 2.6.39-3) (ben@xxxxxxxxxxxxxxx) (gcc version 4.4.6 (Debian 4.4.6-6) ) #1 Tue Jul 5 02:52:23 UTC 2011
[ 0.000000] CPU: vendor_id 'Vortex86 SoC' unknown, using generic init.
[ 0.000000] CPU: Your system may be unstable.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000010000000 (usable)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] DMI not present or invalid.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x10000 max_arch_pfn = 0x100000
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] Base memory trampoline at [c009c000] 9c000 size 12288
[ 0.000000] init_memory_mapping: 0000000000000000-0000000010000000
[ 0.000000] 0000000000 - 0010000000 page 4k
[ 0.000000] kernel direct mapping tables up to 10000000 @ 17bd000-1800000
[ 0.000000] RAMDISK: 0b79a000 - 0c040000
[ 0.000000] ACPI Error: A valid RSDP was not found (20110316/tbxfroot-219)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 256MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 10000000
[ 0.000000] low ram: 0 - 10000000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x00010000
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x00010000
[ 0.000000] On node 0 totalpages: 65423
[ 0.000000] free_area_init_node: node 0, pgdat c13ae4c8, node_mem_map cfdff200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 480 pages used for memmap
[ 0.000000] Normal zone: 60960 pages, LIFO batch:15
[ 0.000000] Using APIC driver default
[ 0.000000] SFI: Simple Firmware Interface v0.81 http://simplefirmware.org
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] APIC: disable apic facility
[ 0.000000] APIC: switched to apic NOOP
[ 0.000000] nr_irqs_gsi: 16
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 10000000 (gap: 10000000:ef000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64911
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.39-2-486 root=UUID=abfa8b1a-1c32-47dd-9bbb-d30941649ec1 ro quiet
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 245492k/262144k available (2541k kernel code, 16200k reserved, 1254k data, 488k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffa1000 - 0xfffff000 ( 376 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff7fe000 ( 751 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] .init : 0xc13b5000 - 0xc142f000 ( 488 kB)
[ 0.000000] .data : 0xc127b500 - 0xc13b4f80 (1254 kB)
[ 0.000000] .text : 0xc1000000 - 0xc127b500 (2541 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] NR_IRQS:288
[ 0.000000] CPU 0 irqstacks, hard=cf806000 soft=cf808000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 800.061 MHz processor.
[ 0.008014] Calibrating delay loop (skipped), value calculated using timer frequency.. 1600.12 BogoMIPS (lpj=3200244)
[ 0.008056] pid_max: default: 32768 minimum: 301
[ 0.012288] Security Framework initialized
[ 0.012337] SELinux: Disabled at boot.
[ 0.012459] Mount-cache hash table entries: 512
[ 0.013325] Initializing cgroup subsys ns
[ 0.013350] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.013377] Initializing cgroup subsys cpuacct
[ 0.013430] Initializing cgroup subsys memory
[ 0.013551] Initializing cgroup subsys devices
[ 0.013573] Initializing cgroup subsys freezer
[ 0.013592] Initializing cgroup subsys net_cls
[ 0.013611] Initializing cgroup subsys blkio
[ 0.013914] CPU: Vortex86 SoC 05/02 stepping 02
[ 0.021830] Performance Events:
[ 0.024926] NMI watchdog disabled (cpu0): hardware events not enabled
[ 0.025614] devtmpfs: initialized
[ 0.028255] print_constraints: dummy:
[ 0.028717] NET: Registered protocol family 16
[ 0.030176] EISA bus registered
[ 0.031748] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=0
[ 0.031770] PCI: Using configuration type 1 for base access
[ 0.039564] bio: create slab <bio-0> at 0
[ 0.040348] ACPI: Interpreter disabled.
[ 0.040936] vgaarb: loaded
[ 0.041592] PCI: Probing PCI hardware
[ 0.041612] PCI: Probing PCI hardware (bus 00)
[ 0.042058] pci 0000:00:00.0: [17f3:6021] type 0 class 0x000600
[ 0.042214] pci 0000:00:01.0: [1002:4c52] type 0 class 0x000300
[ 0.042264] pci 0000:00:01.0: reg 10: [mem 0xfd000000-0xfdffffff]
[ 0.042298] pci 0000:00:01.0: reg 14: [io 0xd800-0xd8ff]
[ 0.042331] pci 0000:00:01.0: reg 18: [mem 0xfebff000-0xfebfffff]
[ 0.042387] pci 0000:00:01.0: reg 30: [mem 0xfebc0000-0xfebdffff pref]
[ 0.042437] pci 0000:00:01.0: supports D1 D2
[ 0.042535] pci 0000:00:07.0: [17f3:6031] type 0 class 0x000601
[ 0.042687] pci 0000:00:08.0: [17f3:6040] type 0 class 0x000200
[ 0.042725] pci 0000:00:08.0: reg 10: [io 0xd600-0xd6ff]
[ 0.042757] pci 0000:00:08.0: reg 14: [mem 0xfebfe400-0xfebfe4ff]
[ 0.042817] pci 0000:00:08.0: reg 30: [mem 0xfebe0000-0xfebeffff pref]
[ 0.042924] pci 0000:00:0a.0: [17f3:6060] type 0 class 0x000c03
[ 0.042963] pci 0000:00:0a.0: reg 10: [mem 0xfebfc000-0xfebfcfff]
[ 0.043100] pci 0000:00:0a.1: [17f3:6061] type 0 class 0x000c03
[ 0.043138] pci 0000:00:0a.1: reg 10: [mem 0xfebfe800-0xfebfe8ff]
[ 0.043291] pci 0000:00:0b.0: [17f3:6060] type 0 class 0x000c03
[ 0.043330] pci 0000:00:0b.0: reg 10: [mem 0xfebfd000-0xfebfdfff]
[ 0.043468] pci 0000:00:0b.1: [17f3:6061] type 0 class 0x000c03
[ 0.043506] pci 0000:00:0b.1: reg 10: [mem 0xfebfec00-0xfebfecff]
[ 0.043659] pci 0000:00:0c.0: [17f3:1011] type 0 class 0x000101
[ 0.043697] pci 0000:00:0c.0: reg 10: [io 0x0000-0x0007]
[ 0.043728] pci 0000:00:0c.0: reg 14: [io 0x0000-0x0003]
[ 0.043759] pci 0000:00:0c.0: reg 18: [io 0x0000-0x0007]
[ 0.043790] pci 0000:00:0c.0: reg 1c: [io 0x0000-0x0003]
[ 0.043821] pci 0000:00:0c.0: reg 20: [io 0xef00-0xef0f]
[ 0.044463] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.046780] pci 0000:00:07.0: default IRQ router [17f3:6031]
[ 0.046891] PCI: pci_cache_line_size set to 32 bytes
[ 0.047048] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.048118] Switching to clocksource pit
[ 0.059274] pnp: PnP ACPI: disabled
[ 0.059298] PnPBIOS: Scanning system for PnP BIOS support...
[ 0.059371] PnPBIOS: Found PnP BIOS installation structure at 0xc00f3140
[ 0.059399] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x3cba, dseg 0xf0000
[ 0.059741] pnp 00:00: [mem 0x00000000-0x0009fbff]
[ 0.059768] pnp 00:00: [mem 0x0009fc00-0x0009ffff]
[ 0.059792] pnp 00:00: [mem 0x000e4000-0x000fffff]
[ 0.059816] pnp 00:00: [mem 0x00100000-0x0fffffff]
[ 0.059840] pnp 00:00: [mem 0xff000000-0xfffbffff]
[ 0.059923] pnp 00:00: [mem 0xfffc0000-0xffffffff]
[ 0.060288] system 00:00: [mem 0x00000000-0x0009fbff] could not be reserved
[ 0.060321] system 00:00: [mem 0x0009fc00-0x0009ffff] could not be reserved
[ 0.060352] system 00:00: [mem 0x000e4000-0x000fffff] could not be reserved
[ 0.060383] system 00:00: [mem 0x00100000-0x0fffffff] could not be reserved
[ 0.060414] system 00:00: [mem 0xff000000-0xfffbffff] has been reserved
[ 0.060445] system 00:00: [mem 0xfffc0000-0xffffffff] has been reserved
[ 0.060479] system 00:00: Plug and Play BIOS device, IDs PNP0c01 (active)
[ 0.060579] pnp 00:01: [io 0x0020-0x0021]
[ 0.060602] pnp 00:01: [io 0x00a0-0x00a1]
[ 0.060625] pnp 00:01: [irq 2]
[ 0.060869] pnp 00:01: Plug and Play BIOS device, IDs PNP0000 (active)
[ 0.060950] pnp 00:02: [dma 4]
[ 0.060972] pnp 00:02: [io 0x0000-0x000f]
[ 0.060994] pnp 00:02: [io 0x0080-0x0090]
[ 0.061016] pnp 00:02: [io 0x0094-0x009f]
[ 0.061038] pnp 00:02: [io 0x00c0-0x00de]
[ 0.061266] pnp 00:02: Plug and Play BIOS device, IDs PNP0200 (active)
[ 0.061346] pnp 00:03: [irq 0]
[ 0.061368] pnp 00:03: [io 0x0040-0x0043]
[ 0.061595] pnp 00:03: Plug and Play BIOS device, IDs PNP0100 (active)
[ 0.061678] pnp 00:04: [irq 8]
[ 0.061700] pnp 00:04: [io 0x0070-0x0071]
[ 0.061931] pnp 00:04: Plug and Play BIOS device, IDs PNP0b00 (active)
[ 0.062032] pnp 00:05: [irq 1]
[ 0.062053] pnp 00:05: [io 0x0060]
[ 0.062087] pnp 00:05: [io 0x0064]
[ 0.062332] pnp 00:05: Plug and Play BIOS device, IDs PNP0303 (active)
[ 0.062636] pnp 00:06: Plug and Play BIOS device, IDs PNP0a03 (disabled)
[ 0.062726] pnp 00:07: [io 0x0061]
[ 0.062956] pnp 00:07: Plug and Play BIOS device, IDs PNP0800 (active)
[ 0.063048] pnp 00:08: [irq 13]
[ 0.063071] pnp 00:08: [io 0x00f0-0x00ff]
[ 0.063301] pnp 00:08: Plug and Play BIOS device, IDs PNP0c04 (active)
[ 0.063398] pnp 00:09: [io 0x04d0-0x04d1]
[ 0.063421] pnp 00:09: [io 0x0cf8-0x0cff]
[ 0.063443] pnp 00:09: [io 0xfc00-0xfc0f]
[ 0.063755] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 0.063787] system 00:09: [io 0x0cf8-0x0cff] could not be reserved
[ 0.063816] system 00:09: [io 0xfc00-0xfc0f] has been reserved
[ 0.063846] system 00:09: Plug and Play BIOS device, IDs PNP0c02 (active)
[ 0.064020] pnp 00:0a: [io 0x03f8-0x03ff]
[ 0.064044] pnp 00:0a: [irq 4]
[ 0.064577] pnp 00:0a: Plug and Play BIOS device, IDs PNP0501 (active)
[ 0.064699] pnp 00:0b: [io 0x02f8-0x02ff]
[ 0.064722] pnp 00:0b: [irq 3]
[ 0.065224] pnp 00:0b: Plug and Play BIOS device, IDs PNP0501 (active)
[ 0.065344] pnp 00:0c: [io 0x03f0-0x03f5]
[ 0.065650] system 00:0c: [io 0x03f0-0x03f5] has been reserved
[ 0.065682] system 00:0c: Plug and Play BIOS device, IDs PNP0c02 (active)
[ 0.065803] pnp 00:0d: [irq 12]
[ 0.066040] pnp 00:0d: Plug and Play BIOS device, IDs PNP0f13 (active)
[ 0.066086] PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
[ 0.090071] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.090101] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.090500] NET: Registered protocol family 2
[ 0.091037] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.092751] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.093059] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.093239] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.093259] TCP reno registered
[ 0.093282] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.093326] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.094250] NET: Registered protocol family 1
[ 0.094353] pci 0000:00:01.0: Boot video device
[ 0.111931] PCI: CLS mismatch (64 != 16), using 32 bytes
[ 0.132289] Unpacking initramfs...
[ 2.710068] Freeing initrd memory: 8856k freed
[ 2.756671] audit: initializing netlink socket (disabled)
[ 2.756757] type=2000 audit(1312221070.752:1): initialized
[ 2.851426] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 2.852407] VFS: Disk quotas dquot_6.5.2
[ 2.852567] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.853016] msgmni has been set to 496
[ 2.854393] alg: No test for stdrng (krng)
[ 2.854659] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.854687] io scheduler noop registered
[ 2.854705] io scheduler deadline registered
[ 2.854783] io scheduler cfq registered (default)
[ 2.857291] isapnp: Scanning for PnP cards...
[ 3.211351] isapnp: No Plug & Play device found
[ 3.211900] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 3.216667] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.221364] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.228066] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.233118] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.235022] Linux agpgart interface v0.103
[ 3.237607] i8042: PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
[ 3.240502] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.240553] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.241961] mousedev: PS/2 mouse device common for all mice
[ 3.242901] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 3.242976] rtc0: alarms up to one day, 114 bytes nvram
[ 3.243535] EISA: Probing bus 0 at eisa.0
[ 3.243715] EISA: Detected 0 cards.
[ 3.243735] cpuidle: using governor ladder
[ 3.243754] cpuidle: using governor menu
[ 3.245860] TCP cubic registered
[ 3.246085] NET: Registered protocol family 10
[ 3.251068] Mobile IPv6
[ 3.251093] NET: Registered protocol family 17
[ 3.251137] Registering the dns_resolver key type
[ 3.251226] Using IPI Shortcut mode
[ 3.252273] PM: Hibernation image not present or could not be loaded.
[ 3.252358] registered taskstats version 1
[ 3.253148] rtc_cmos 00:04: setting system clock to 2011-08-01 17:51:11 UTC (1312221071)
[ 3.253332] Initializing network drop monitor service
[ 3.254122] Freeing unused kernel memory: 488k freed
[ 3.256988] Write protecting the kernel text: 2544k
[ 3.257167] Write protecting the kernel read-only data: 980k
[ 3.263988] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 3.388934] udev[43]: starting version 164
[ 3.848235] Switching to clocksource tsc
[ 4.702577] r6040: RDC R6040 NAPI net driver,version 0.27 (23Feb2011)
[ 4.773121] r6040_eth_mii: probed
[ 4.775313] r6040 0000:00:08.0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01)
[ 5.511399] usbcore: registered new interface driver usbfs
[ 5.512933] usbcore: registered new interface driver hub
[ 5.513338] usbcore: registered new device driver usb
[ 5.703192] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.703417] ehci_hcd 0000:00:0a.1: EHCI Host Controller
[ 5.703622] ehci_hcd 0000:00:0a.1: new USB bus registered, assigned bus number 1
[ 5.705371] SCSI subsystem initialized
[ 5.724244] ehci_hcd 0000:00:0a.1: irq 9, io mem 0xfebfe800
[ 5.736148] ehci_hcd 0000:00:0a.1: USB 2.0 started, EHCI 1.00
[ 5.736378] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.736408] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.736433] usb usb1: Product: EHCI Host Controller
[ 5.736455] usb usb1: Manufacturer: Linux 2.6.39-2-486 ehci_hcd
[ 5.736477] usb usb1: SerialNumber: 0000:00:0a.1
[ 5.740633] hub 1-0:1.0: USB hub found
[ 5.740694] hub 1-0:1.0: 2 ports detected
[ 5.741320] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 5.741412] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 5.764604] ehci_hcd 0000:00:0b.1: irq 11, io mem 0xfebfec00
[ 5.777398] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
[ 5.777606] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.777635] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.777660] usb usb2: Product: EHCI Host Controller
[ 5.777682] usb usb2: Manufacturer: Linux 2.6.39-2-486 ehci_hcd
[ 5.777705] usb usb2: SerialNumber: 0000:00:0b.1
[ 5.779788] hub 2-0:1.0: USB hub found
[ 5.779846] hub 2-0:1.0: 2 ports detected
[ 5.942142] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.942371] ohci_hcd 0000:00:0a.0: OHCI Host Controller
[ 5.942460] ohci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 3
[ 5.942618] ohci_hcd 0000:00:0a.0: irq 5, io mem 0xfebfc000
[ 6.073680] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.073718] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.073743] usb usb3: Product: OHCI Host Controller
[ 6.073764] usb usb3: Manufacturer: Linux 2.6.39-2-486 ohci_hcd
[ 6.073787] usb usb3: SerialNumber: 0000:00:0a.0
[ 6.078152] hub 3-0:1.0: USB hub found
[ 6.078213] hub 3-0:1.0: 2 ports detected
[ 6.078855] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 6.078933] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 4
[ 6.079087] ohci_hcd 0000:00:0b.0: irq 10, io mem 0xfebfd000
[ 6.399142] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.399181] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.399207] usb usb4: Product: OHCI Host Controller
[ 6.399228] usb usb4: Manufacturer: Linux 2.6.39-2-486 ohci_hcd
[ 6.399251] usb usb4: SerialNumber: 0000:00:0b.0
[ 6.401382] hub 4-0:1.0: USB hub found
[ 6.401441] hub 4-0:1.0: 2 ports detected
[ 6.416316] libata version 3.00 loaded.
[ 6.474576] pata_rdc 0000:00:0c.0: version 0.01
[ 6.475316] pata_rdc 0000:00:0c.0: setting latency timer to 64
[ 6.481033] scsi0 : pata_rdc
[ 6.482451] scsi1 : pata_rdc
[ 6.483528] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xef00 irq 14
[ 6.483555] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xef08 irq 15
[ 6.714752] ata1.00: ATA-8: WDC WD1200BEVE-00WZT0, 01.01A01, max UDMA/100
[ 6.714786] ata1.00: 234441648 sectors, multi 16: LBA48
[ 6.714849] ata1.01: ATA-0: SILICONSYSTEMS INC 512MB, V2.27d, max MWDMA2
[ 6.714875] ata1.01: 1019088 sectors, multi 0: LBA
[ 6.714911] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 6.721008] ata1.00: configured for UDMA/33
[ 6.728246] ata1.01: configured for MWDMA2
[ 6.729094] scsi 0:0:0:0: Direct-Access ATA WDC WD1200BEVE-0 01.0 PQ: 0 ANSI: 5
[ 6.732293] scsi 0:0:1:0: Direct-Access ATA SILICONSYSTEMS I V2.2 PQ: 0 ANSI: 5
[ 6.993335] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 6.993998] sd 0:0:0:0: [sda] Write Protect is off
[ 6.994029] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.994311] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.042216] sd 0:0:1:0: [sdb] 1019088 512-byte logical blocks: (521 MB/497 MiB)
[ 7.042889] sd 0:0:1:0: [sdb] Write Protect is off
[ 7.042919] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 7.043202] sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 7.048391] sda: sda1
[ 37.827489] ata1: lost interrupt (Status 0x58)
[ 37.827910] ata1: drained 512 bytes to clear DRQ.
[ 37.827961] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 37.828060] ata1.01: failed command: READ DMA
[ 37.828162] ata1.01: cmd c8/00:08:00:00:00/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 37.828176] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 37.828311] ata1.01: status: { DRDY }
[ 37.828452] ata1: soft resetting link
[ 38.280580] ata1.00: configured for UDMA/33
[ 38.287670] ata1.01: configured for MWDMA2
[ 38.287707] ata1.01: device reported invalid CHS sector 0
[ 38.287753] ata1: EH complete
[ 68.834877] ata1: lost interrupt (Status 0x58)
[ 68.835285] ata1: drained 512 bytes to clear DRQ.
[ 68.835323] ata1.01: limiting speed to MWDMA1:PIO4
[ 68.835354] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 68.835448] ata1.01: failed command: READ DMA
[ 68.835548] ata1.01: cmd c8/00:08:00:00:00/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 68.835562] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 68.835698] ata1.01: status: { DRDY }
[ 68.835827] ata1: soft resetting link
[ 69.295660] ata1.00: configured for UDMA/33
[ 69.303102] ata1.01: configured for MWDMA1
[ 69.303134] ata1.01: device reported invalid CHS sector 0
[ 69.303175] ata1: EH complete
[ 99.874284] ata1: lost interrupt (Status 0x58)
[ 99.874784] ata1: drained 512 bytes to clear DRQ.
[ 99.874819] ata1.01: limiting speed to PIO4
[ 99.874849] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 99.874941] ata1.01: failed command: READ DMA
[ 99.875041] ata1.01: cmd c8/00:08:00:00:00/00:00:00:00:00/f0 tag 0 dma 4096 in
[ 99.875055] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 99.875191] ata1.01: status: { DRDY }
[ 99.875319] ata1: soft resetting link
[ 100.334769] ata1.00: configured for UDMA/33
[ 100.342485] ata1.01: configured for PIO4
[ 100.342515] ata1.01: device reported invalid CHS sector 0
[ 100.342556] ata1: EH complete
[ 100.344624] sdb: sdb1
[ 100.351473] sd 0:0:0:0: [sda] Attached SCSI disk
[ 100.352914] sdb: detected capacity change from 0 to 521773056
[ 100.355713] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 100.368940] sdb: detected capacity change from 0 to 521773056
[ 101.098544] EXT3-fs: barriers not enabled
[ 101.115725] kjournald starting. Commit interval 5 seconds
[ 101.116337] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 102.745488] udev[188]: starting version 164
[ 103.764805] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 105.148637] psmouse serio1: ID: 10 00 64
[ 105.201325] udev[199]: renamed network interface eth0 to eth1
[ 105.231639] input: GenPS/2 Genius Mouse as /devices/platform/i8042/serio1/input/input2
[ 105.760437] Error: Driver 'pcspkr' is already registered, aborting...
[ 107.348112] EXT3-fs (sda1): using internal journal
[ 107.850449] loop: module loaded
[ 114.335208] sshd (857): /proc/857/oom_adj is deprecated, please use /proc/857/oom_score_adj instead.
[ 304.062346] eth1: no IPv6 routers present
00:00.0 Host bridge: RDC Semiconductor, Inc. R6021 Host Bridge (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
00: f3 17 21 60 0e 00 00 22 02 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 fc 00 00 49 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 34 1e 00 00 00 e1 00 9f c9 0e 00 7a 27 00 00
70: 03 00 00 00 55 56 0b 00 00 00 00 00 00 00 00 00
80: 00 00 00 f0 50 05 d0 17 00 00 00 00 00 00 00 00
90: 44 4d 50 32 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: c2 00 00 01 0a 03 a6 b7 c8 d9 ea fb 0c 1d 2e 3f
e0: 50 61 72 83 31 31 31 39 d8 e9 fa 0b 1c 2d 3e 4f
f0: 01 00 00 00 05 00 00 00 08 00 00 00 00 00 00 00
00:01.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M (rev 64) (prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc Rage Mobility P/M
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 0
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at febc0000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 52 4c 87 00 90 02 64 00 00 03 10 80 00 00
10: 00 00 00 fd 01 d8 00 00 00 f0 bf fe 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 52 4c
30: 00 00 bc fe 5c 00 00 00 00 00 00 00 00 01 08 00
40: 0c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 5c 10 00 01 00 00 ff 00 00 00 00 01 00 01 06
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.0 ISA bridge: RDC Semiconductor, Inc. R6031 ISA Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=?? >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00: f3 17 31 60 0f 00 00 06 02 00 01 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 16 00 00 77 d5 07 1b 00 12 ff 3f f1 ff 00 00
50: d2 15 00 94 f8 03 00 00 00 00 06 15 00 00 00 00
60: 78 00 79 00 7a 00 7b 00 7c 00 98 00 9f 02 00 00
70: 10 00 00 00 e0 01 00 00 f0 ff ff 02 d0 01 00 00
80: f0 ff ff 02 00 00 00 00 00 00 00 00 fe ff ff 0d
90: 00 c0 0c 00 c0 ff ff 0d 00 01 00 00 fe ff ff 04
a0: f8 02 a2 00 00 00 20 00 00 00 20 00 00 00 20 00
b0: 00 00 00 04 93 fd 00 00 00 00 00 00 80 13 7c 00
c0: 40 01 2d 03 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00
e0: 00 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:08.0 Ethernet controller: RDC Semiconductor, Inc. R6040 MAC Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (750ns min, 2000ns max)
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at d600 [size=256]
Region 1: Memory at febfe400 (32-bit, non-prefetchable) [size=256]
Expansion ROM at febe0000 [disabled] [size=64K]
Kernel driver in use: r6040
00: f3 17 40 60 07 00 00 02 00 00 00 02 00 80 00 00
10: 01 d6 00 00 00 e4 bf fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 be fe 00 00 00 00 00 00 00 00 07 01 03 08
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0a.0 USB Controller: RDC Semiconductor, Inc. R6060 USB 1.1 Controller (rev 12) (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00: f3 17 60 60 06 01 00 02 12 10 03 0c 08 80 80 00
10: 00 c0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 01 00 00
40: 09 00 30 10 0c 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0a.1 USB Controller: RDC Semiconductor, Inc. R6061 USB 2.0 Controller (rev 03) (prog-if 20 [EHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 9
Region 0: Memory at febfe800 (32-bit, non-prefetchable) [size=256]
Kernel driver in use: ehci_hcd
00: f3 17 61 60 06 01 00 02 03 20 03 0c 08 80 00 00
10: 00 e8 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 09 02 00 00
40: 09 00 30 10 0c 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 00 00 00 00 00 08 40 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0b.0 USB Controller: RDC Semiconductor, Inc. R6060 USB 1.1 Controller (rev 12) (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00: f3 17 60 60 06 01 00 02 12 10 03 0c 08 80 80 00
10: 00 d0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
40: 09 00 30 10 0c 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0b.1 USB Controller: RDC Semiconductor, Inc. R6061 USB 2.0 Controller (rev 03) (prog-if 20 [EHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 11
Region 0: Memory at febfec00 (32-bit, non-prefetchable) [size=256]
Kernel driver in use: ehci_hcd
00: f3 17 61 60 06 01 00 02 03 20 03 0c 08 80 00 00
10: 00 ec bf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00
40: 09 00 30 10 0c 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 00 00 00 00 00 08 40 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0c.0 IDE interface: RDC Semiconductor, Inc. Device 1011 (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: RDC Semiconductor, Inc. Device 1011
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 14
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ef00 [size=16]
Kernel driver in use: pata_rdc
00: f3 17 11 10 05 00 00 02 01 8a 01 01 04 40 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: 01 ef 00 00 00 00 00 00 00 00 00 00 f3 17 11 10
30: 00 00 00 00 00 00 00 00 00 00 00 00 0e 01 00 00
40: 77 e3 00 c0 0b 00 00 00 01 00 02 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 02 00 c0 00 40 08 00 00 00 00 00 00 00 00
a0: 00 00 00 00 04 40 04 40 1b 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
