On Sun, Apr 25, 2010 at 10:57 AM, Richard Genoud
<richard.genoud@xxxxxxxxx> wrote:
> 2010/4/25 Robert Hancock <hancockrwd@xxxxxxxxx>:
>> Usually this sort of thing is some kind of hardware problem - either a
>> firmware bug in the drive, or else a SATA link communication problem like a
>> bad cable, or the drives not getting clean power under load.
> I'll try other sata cables, but I'm afraid, like you said, that it's a
> firmware bug...
>
>> The log is missing the detail messages indicating what actually happened -
>> can you post the output from dmesg instead?
> you're right, there's more informations in there :
>
> [ 2.701742] ahci 0000:00:1f.2: version 3.0
> [ 2.701751] alloc irq_desc for 21 on node 0
> [ 2.701752] alloc kstat_irqs on node 0
> [ 2.701756] ahci 0000:00:1f.2: PCI INT D -> GSI 21 (level, low) -> IRQ 21
> [ 2.701826] alloc irq_desc for 35 on node 0
> [ 2.701827] alloc kstat_irqs on node 0
> [ 2.701833] ahci 0000:00:1f.2: irq 35 for MSI/MSI-X
> [ 2.701855] ahci: SSS flag set, parallel bus scan disabled
> [ 2.719878] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3
> Gbps 0x3f impl SATA mode
> [ 2.719947] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led
> clo pmp pio slum part ems
> [ 2.720011] ahci 0000:00:1f.2: setting latency timer to 64
> [ 2.819723] scsi0 : ahci
> [ 2.819817] scsi1 : ahci
> [ 2.819888] scsi2 : ahci
> [ 2.819960] scsi3 : ahci
> [ 2.820034] scsi4 : ahci
> [ 2.820104] scsi5 : ahci
> [ 2.820226] ata1: SATA max UDMA/133 abar m2048@0xfbaf7000 port
> 0xfbaf7100 irq 35
> [ 2.820288] ata2: SATA max UDMA/133 abar m2048@0xfbaf7000 port
> 0xfbaf7180 irq 35
> [ 2.820349] ata3: SATA max UDMA/133 abar m2048@0xfbaf7000 port
> 0xfbaf7200 irq 35
> [ 2.820411] ata4: SATA max UDMA/133 abar m2048@0xfbaf7000 port
> 0xfbaf7280 irq 35
> [ 2.820472] ata5: SATA max UDMA/133 abar m2048@0xfbaf7000 port
> 0xfbaf7300 irq 35
> [ 2.820534] ata6: SATA max UDMA/133 abar m2048@0xfbaf7000 port
> 0xfbaf7380 irq 35
> [ 2.820630] ahci 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 2.839665] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3
> Gbps 0x3 impl SATA mode
> [ 2.839736] ahci 0000:03:00.0: flags: 64bit ncq led clo pmp pio
> [ 2.839787] ahci 0000:03:00.0: setting latency timer to 64
> [ 2.839869] scsi6 : ahci
> [ 2.839939] scsi7 : ahci
> [ 2.840024] ata7: SATA max UDMA/133 abar m8192@0xfbdfa000 port
> 0xfbdfa100 irq 18
> [ 2.840086] ata8: SATA max UDMA/133 abar m8192@0xfbdfa000 port
> 0xfbdfa180 irq 18
> [ 3.348939] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 3.366808] ata1.00: ATA-7: HDS728080PLA380, PF2OA60A, max UDMA/133
> [ 3.366869] ata1.00: 160836480 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 3.368030] ata1.00: configured for UDMA/133
> [ 4.317329] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 4.338405] ata2.00: ATA-7: HDS728080PLA380, PF2OA60A, max UDMA/133
> [ 4.338466] ata2.00: 160836480 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 4.339643] ata2.00: configured for UDMA/133
> [ 5.285674] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 5.305917] ata3.00: ATA-8: Hitachi HDP725050GLA360, GM4OA5CA, max UDMA/133
> [ 5.305979] ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 5.307132] ata3.00: configured for UDMA/133
> [ 5.675046] ata4: SATA link down (SStatus 0 SControl 300)
> [ 6.044399] ata5: SATA link down (SStatus 0 SControl 300)
> [ 6.413775] ata6: SATA link down (SStatus 0 SControl 300)
..
> [16840.450530] ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen
> [16840.450535] ata1.00: cmd 61/b8:00:20:d5:8b/02:00:05:00:00/40 tag 0
> ncq 356352 out
> [16840.450536] res 40/00:00:00:4f:c2/00:01:00:00:00/00 Emask
> 0x4 (timeout)
> [16840.450538] ata1.00: status: { DRDY }
> [16840.450541] ata1.00: cmd 61/80:08:99:bd:86/01:00:09:00:00/40 tag 1
> ncq 196608 out
> [16840.450542] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
> 0x4 (timeout)
> [16840.450543] ata1.00: status: { DRDY }
> [16840.450546] ata1: hard resetting link
> [16840.978820] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [16840.981055] ata1.00: configured for UDMA/133
> [16840.981064] ata1.00: device reported invalid CHS sector 0
> [16840.981069] ata1.00: device reported invalid CHS sector 0
> [16840.981078] ata1: EH complete
Looks like it's only happening on one of the drives, I'd suspect
there's some kind of drive fault or power problem specific to that
one..
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
