On 03/26/2010 08:36 PM, David Fries wrote:
On Fri, Mar 26, 2010 at 08:12:26PM -0400, Jeff Garzik wrote:
On 03/26/2010 07:21 PM, David Fries wrote:
The kernel fails to see the entire disk with 2.6.34-rc2 with VIA
vt82c586b chipset. I tracked it down to commit
f931a5d5785d7b7c44871bd7ad2762e29dfddf29 "via82cxxx: workaround h/w
bugs" and reverting just that one solves the problem, or just
commenting out just one outb write in that change.
via82cxxx 0000:00:07.1: VIA vt82c586b (rev 41) IDE UDMA33
via82cxxx 0000:00:07.1: IDE controller (0x1106:0x0571 rev 0x06)
via82cxxx 0000:00:07.1: not 100% native mode: will probe irqs later
Note the kernel panic is intentional as I'm given the test kernel an
invalid root device, so that I can suspend to disk, try a kernel,
resume and pick up where I left off. It does have a side benefit of
dumping the size of all partitions.
2.6.34-rc2 unmodified, fails and sees 30985416 KiB for the last
partition.
ide-gd driver 1.18
hda: max request size: 128KiB
hda: 66055248 sectors (33820 MB) w/7936KiB Cache, CHS=65531/16/63
hda: cache flushes supported
hda: hda1 hda2 hda3
hda: p3 size 236037312 exceeds device capacity, enabling native capacity
hda: p3 size 236037312 exceeds device capacity, limited to end of disk
ide-cd driver 5.00
...
Please append a correct "root=" boot option; here are the available partitions:
0300 33027624 hda driver: ide-gd
0301 49391 hda1
0302 1992816 hda2
0303 30985416 hda3
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(22,2)
2.6.34-rc2 with patch revered, correct size 118018656
ide-gd driver 1.18
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 66055248 sectors (33820 MB)
native capacity is 240121728 sectors (122942 MB)
hda: 66055248 sectors (33820 MB) w/7936KiB Cache, CHS=65531/16/63
hda: cache flushes supported
hda: hda1 hda2 hda3
hda: p3 size 236037312 exceeds device capacity, enabling native capacity
hda: detected capacity change from 33820286976 to 122942324736
ide-cd driver 5.00
0300 120060864 hda driver: ide-gd
0301 49391 hda1
0302 1992816 hda2
0303 118018656 hda3
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(22,2)
Here are two debug patches, the first adds debug prints and the second
disables the problematic write, I have the output of both included.
From dac7d14ce1f227d8a084c3ec218ea1430bffdc57 Mon Sep 17 00:00:00 2001
From: David Fries<david@xxxxxxxxx>
Date: Thu, 25 Mar 2010 19:51:31 -0500
Subject: [PATCH 1/2] fails: add print messages
add print messages for debugging
---
drivers/ide/via82cxxx.c | 5 +++++
1 files changed, 5 insertions(+), 0 deletions(-)
Does libata + pata_via work, if you pass ignore_hpa=1 module option to
libata?
Jeff
No, here is the output with ignore_hpa=1 on the command line. I also
don't see any difference with it not on the command line.
I said "module option", which is different from a kernel command line
option.
If you are trying to build a module into the kernel image itself, you
must use the "modulename.moduleoption" format on the kernel command
line, ie. libata.ignore_hpa=1
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xe400 irq 14
ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xe408 irq 15
ata1.00: HPA detected: current 66055248, native 240121728
ata1.00: ATA-7: Maxtor 6Y120P0, YAR41BW0, max UDMA/133
ata1.00: 66055248 sectors, multi 16: LBA
ata1.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y120P0 YAR4 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 66055248 512-byte logical blocks: (33.8 GB/31.4 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sda: p3 size 236037312 exceeds device capacity, limited to end of disk
This message should hopefully change, when the module option is
correctly specified.
sd 0:0:0:0: [sda] Attached SCSI disk
ata2.01: ATAPI: PLEXTOR CD-R PX-W4012A, 1.06, max UDMA/33
ata2.01: configured for UDMA/33
scsi 1:0:1:0: CD-ROM PLEXTOR CD-R PX-W4012A 1.06 PQ: 0 ANSI: 5
...
VFS: Cannot open root device "1602" or unknown-block(22,2)
Please append a correct "root=" boot option; here are the available partitions:
0800 33027624 sda driver: sd
0801 49391 sda1
0802 1992816 sda2
0803 30985416 sda3
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(22,2)
All these errors related to unknown-block(22,2) are it trying to find
/dev/hdX, when libata uses the SCSI block devices /dev/sdX
These errors are unrelated to HPA, and are a standard issue encountered
when moving from legacy IDE driver to libata.
Jeff
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
