From: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
Subject: [PATCH] serverworks: convert to ide2libata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
---
drivers/ata/pata_serverworks.h | 20 ++
drivers/ide/serverworks.c | 281 ++---------------------------------------
2 files changed, 40 insertions(+), 261 deletions(-)
Index: b/drivers/ata/pata_serverworks.h
===================================================================
--- a/drivers/ata/pata_serverworks.h
+++ b/drivers/ata/pata_serverworks.h
@@ -11,6 +11,9 @@
* *** to detect 80-conductor cable presence. ***
*
* CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
+ *
+ * HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
+ * controller same as the CSB6. Single channel ATA100 only.
*/
#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
@@ -213,6 +216,10 @@ static int serverworks_fixup_csb(struct
pci_write_config_dword(findev, 0x4C, reg4c);
pci_dev_put(findev);
}
+#ifdef __IDE2LIBATA
+ outb_p(0x06, 0x0c00);
+ pdev->irq = inb_p(0x0c01);
+#endif
} else {
struct pci_dev *findev = NULL;
u8 reg41 = 0;
@@ -225,6 +232,17 @@ static int serverworks_fixup_csb(struct
pci_write_config_byte(findev, 0x41, reg41);
pci_dev_put(findev);
}
+#ifdef __IDE2LIBATA
+ /*
+ * This is a device pin issue on CSB6.
+ * Since there will be a future raid mode,
+ * early versions of the chipset require the
+ * interrupt pin to be set, and it is a compatibility
+ * mode issue.
+ */
+ if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE)
+ pdev->irq = 0;
+#endif
}
/* setup the UDMA Control register
*
@@ -268,7 +286,9 @@ static int serverworks_fixup(struct pci_
rc = serverworks_fixup_osb4(pdev);
break;
case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
+#ifndef __IDE2LIBATA
ata_pci_bmdma_clear_simplex(pdev);
+#endif
/* fall through */
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
Index: b/drivers/ide/serverworks.c
===================================================================
--- a/drivers/ide/serverworks.c
+++ b/drivers/ide/serverworks.c
@@ -8,21 +8,6 @@
*
* RCC/ServerWorks IDE driver for Linux
*
- * OSB4: `Open South Bridge' IDE Interface (fn 1)
- * supports UDMA mode 2 (33 MB/s)
- *
- * CSB5: `Champion South Bridge' IDE Interface (fn 1)
- * all revisions support UDMA mode 4 (66 MB/s)
- * revision A2.0 and up support UDMA mode 5 (100 MB/s)
- *
- * *** The CSB5 does not provide ANY register ***
- * *** to detect 80-conductor cable presence. ***
- *
- * CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
- *
- * HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
- * controller same as the CSB6. Single channel ATA100 only.
- *
* Documentation:
* Available under NDA only. Errata info very hard to get.
*
@@ -39,19 +24,6 @@
#define DRV_NAME "serverworks"
-#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
-#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
-
-/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
- * can overrun their FIFOs when used with the CSB5 */
-static const char *svwks_bad_ata100[] = {
- "ST320011A",
- "ST340016A",
- "ST360021A",
- "ST380021A",
- NULL
-};
-
static int check_in_drive_lists (ide_drive_t *drive, const char **list)
{
char *m = (char *)&drive->id[ATA_ID_PROD];
@@ -62,6 +34,19 @@ static int check_in_drive_lists (ide_dri
return 0;
}
+static int ata_cable_40wire(ide_hwif_t *hwif)
+{
+ return ATA_CBL_PATA40;
+}
+
+static int ata_cable_unknown(ide_hwif_t *hwif)
+{
+ return ATA_CBL_PATA80;
+}
+
+#include <linux/ide2libata.h>
+#include "../ata/pata_serverworks.h"
+
static u8 svwks_udma_filter(ide_drive_t *drive)
{
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
@@ -78,7 +63,7 @@ static u8 svwks_udma_filter(ide_drive_t
/* If someone decides to do UDMA133 on CSB5 the same
issue will bite so be inclusive */
- if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
+ if (mode > 2 && check_in_drive_lists(drive, csb_bad_ata100))
mode = 2;
switch(mode) {
@@ -92,249 +77,23 @@ static u8 svwks_udma_filter(ide_drive_t
}
}
-static u8 svwks_csb_check (struct pci_dev *dev)
-{
- switch (dev->device) {
- case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
- case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
- case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
- case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
- return 1;
- default:
- break;
- }
- return 0;
-}
-
-static void svwks_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
- static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
-
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- const u8 pio = drive->pio_mode - XFER_PIO_0;
-
- pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);
-
- if (svwks_csb_check(dev)) {
- u16 csb_pio = 0;
-
- pci_read_config_word(dev, 0x4a, &csb_pio);
-
- csb_pio &= ~(0x0f << (4 * drive->dn));
- csb_pio |= (pio << (4 * drive->dn));
-
- pci_write_config_word(dev, 0x4a, csb_pio);
- }
-}
-
-static void svwks_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- static const u8 udma_modes[] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
- static const u8 dma_modes[] = { 0x77, 0x21, 0x20 };
- static const u8 drive_pci2[] = { 0x45, 0x44, 0x47, 0x46 };
-
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- const u8 speed = drive->dma_mode;
- u8 unit = drive->dn & 1;
-
- u8 ultra_enable = 0, ultra_timing = 0, dma_timing = 0;
-
- pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
- pci_read_config_byte(dev, 0x54, &ultra_enable);
-
- ultra_timing &= ~(0x0F << (4*unit));
- ultra_enable &= ~(0x01 << drive->dn);
-
- if (speed >= XFER_UDMA_0) {
- dma_timing |= dma_modes[2];
- ultra_timing |= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
- ultra_enable |= (0x01 << drive->dn);
- } else if (speed >= XFER_MW_DMA_0)
- dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
-
- pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
- pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
- pci_write_config_byte(dev, 0x54, ultra_enable);
-}
-
static int init_chipset_svwks(struct pci_dev *dev)
{
- unsigned int reg;
- u8 btr;
-
- /* force Master Latency Timer value to 64 PCICLKs */
- pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
-
- /* OSB4 : South Bridge and IDE */
- if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
- struct pci_dev *isa_dev =
- pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
- PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
- if (isa_dev) {
- pci_read_config_dword(isa_dev, 0x64, ®);
- reg &= ~0x00002000; /* disable 600ns interrupt mask */
- if(!(reg & 0x00004000))
- printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
- "enabled.\n", pci_name(dev));
- reg |= 0x00004000; /* enable UDMA/33 support */
- pci_write_config_dword(isa_dev, 0x64, reg);
- pci_dev_put(isa_dev);
- }
- }
-
- /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
- else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
- (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
- (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
-
- /* Third Channel Test */
- if (!(PCI_FUNC(dev->devfn) & 1)) {
- struct pci_dev * findev = NULL;
- u32 reg4c = 0;
- findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
- PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
- if (findev) {
- pci_read_config_dword(findev, 0x4C, ®4c);
- reg4c &= ~0x000007FF;
- reg4c |= 0x00000040;
- reg4c |= 0x00000020;
- pci_write_config_dword(findev, 0x4C, reg4c);
- pci_dev_put(findev);
- }
- outb_p(0x06, 0x0c00);
- dev->irq = inb_p(0x0c01);
- } else {
- struct pci_dev * findev = NULL;
- u8 reg41 = 0;
-
- findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
- PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
- if (findev) {
- pci_read_config_byte(findev, 0x41, ®41);
- reg41 &= ~0x40;
- pci_write_config_byte(findev, 0x41, reg41);
- pci_dev_put(findev);
- }
- /*
- * This is a device pin issue on CSB6.
- * Since there will be a future raid mode,
- * early versions of the chipset require the
- * interrupt pin to be set, and it is a compatibility
- * mode issue.
- */
- if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
- dev->irq = 0;
- }
-// pci_read_config_dword(dev, 0x40, &pioreg)
-// pci_write_config_dword(dev, 0x40, 0x99999999);
-// pci_read_config_dword(dev, 0x44, &dmareg);
-// pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
- /* setup the UDMA Control register
- *
- * 1. clear bit 6 to enable DMA
- * 2. enable DMA modes with bits 0-1
- * 00 : legacy
- * 01 : udma2
- * 10 : udma2/udma4
- * 11 : udma2/udma4/udma5
- */
- pci_read_config_byte(dev, 0x5A, &btr);
- btr &= ~0x40;
- if (!(PCI_FUNC(dev->devfn) & 1))
- btr |= 0x2;
- else
- btr |= (dev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
- pci_write_config_byte(dev, 0x5A, btr);
- }
- /* Setup HT1000 SouthBridge Controller - Single Channel Only */
- else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
- pci_read_config_byte(dev, 0x5A, &btr);
- btr &= ~0x40;
- btr |= 0x3;
- pci_write_config_byte(dev, 0x5A, btr);
- }
+ (void)serverworks_fixup(dev);
return 0;
}
-static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
-{
- return ATA_CBL_PATA80;
-}
-
-/* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
- * of the subsystem device ID indicate presence of an 80-pin cable.
- * Bit 15 clear = secondary IDE channel does not have 80-pin cable.
- * Bit 15 set = secondary IDE channel has 80-pin cable.
- * Bit 14 clear = primary IDE channel does not have 80-pin cable.
- * Bit 14 set = primary IDE channel has 80-pin cable.
- */
-static u8 ata66_svwks_dell(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
-
- if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
- dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
- (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
- dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
- return ((1 << (hwif->channel + 14)) &
- dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
- return ATA_CBL_PATA40;
-}
-
-/* Sun Cobalt Alpine hardware avoids the 80-pin cable
- * detect issue by attaching the drives directly to the board.
- * This check follows the Dell precedent (how scary is that?!)
- *
- * WARNING: this only works on Alpine hardware!
- */
-static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
-
- if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
- dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
- dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
- return ((1 << (hwif->channel + 14)) &
- dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
- return ATA_CBL_PATA40;
-}
-
-static int svwks_cable_detect(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
-
- /* Server Works */
- if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
- return ata66_svwks_svwks (hwif);
-
- /* Dell PowerEdge */
- if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
- return ata66_svwks_dell (hwif);
-
- /* Cobalt Alpine */
- if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
- return ata66_svwks_cobalt (hwif);
-
- /* Per Specified Design by OEM, and ASIC Architect */
- if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
- (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
- return ATA_CBL_PATA80;
-
- return ATA_CBL_PATA40;
-}
-
static const struct ide_port_ops osb4_port_ops = {
- .set_pio_mode = svwks_set_pio_mode,
- .set_dma_mode = svwks_set_dma_mode,
+ .set_pio_mode = serverworks_set_piomode,
+ .set_dma_mode = serverworks_set_dmamode,
};
static const struct ide_port_ops svwks_port_ops = {
- .set_pio_mode = svwks_set_pio_mode,
- .set_dma_mode = svwks_set_dma_mode,
+ .set_pio_mode = serverworks_set_piomode,
+ .set_dma_mode = serverworks_set_dmamode,
.udma_filter = svwks_udma_filter,
- .cable_detect = svwks_cable_detect,
+ .cable_detect = serverworks_cable_detect,
};
static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
