From: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
Subject: [PATCH] it8213: convert to ide2libata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
---
drivers/ata/pata_it8213.h | 11 +++
drivers/ide/it8213.c | 138 +---------------------------------------------
2 files changed, 13 insertions(+), 136 deletions(-)
Index: b/drivers/ata/pata_it8213.h
===================================================================
--- a/drivers/ata/pata_it8213.h
+++ b/drivers/ata/pata_it8213.h
@@ -141,9 +141,16 @@ static void it8213_set_dmamode(struct at
ideconf |= u_clock << devid;
pci_write_config_word(dev, 0x54, ideconf);
} else {
- /* MWDMA is driven by the PIO timings. */
+ /* Normal DMA is driven by the PIO timings. */
+#ifdef __IDE2LIBATA
+ if (speed >= XFER_MW_DMA_0)
+ adev->pio_mode = ata_mwdma_to_pio(speed) + XFER_PIO_0;
+ else
+ adev->pio_mode = XFER_PIO_2; /* for SWDMA2 */
+ it8213_set_timings(ap, adev, adev->pio_mode - XFER_PIO_0, 1);
+#else
it8213_set_timings(ap, adev, ata_mwdma_to_pio(speed), 1);
-
+#endif
udma_enable &= ~(1 << devid);
}
pci_write_config_byte(dev, 0x48, udma_enable);
Index: b/drivers/ide/it8213.c
===================================================================
--- a/drivers/ide/it8213.c
+++ b/drivers/ide/it8213.c
@@ -15,142 +15,12 @@
#define DRV_NAME "it8213"
-/**
- * it8213_set_pio_mode - set host controller for PIO mode
- * @hwif: port
- * @drive: drive
- *
- * Set the interface PIO mode.
- */
-
-static void it8213_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- int is_slave = drive->dn & 1;
- int master_port = 0x40;
- int slave_port = 0x44;
- unsigned long flags;
- u16 master_data;
- u8 slave_data;
- static DEFINE_SPINLOCK(tune_lock);
- int control = 0;
- const u8 pio = drive->pio_mode - XFER_PIO_0;
-
- static const u8 timings[][2] = {
- { 0, 0 },
- { 0, 0 },
- { 1, 0 },
- { 2, 1 },
- { 2, 3 }, };
-
- spin_lock_irqsave(&tune_lock, flags);
- pci_read_config_word(dev, master_port, &master_data);
-
- if (pio > 1)
- control |= 1; /* Programmable timing on */
- if (drive->media != ide_disk)
- control |= 4; /* ATAPI */
- if (ide_pio_need_iordy(drive, pio))
- control |= 2; /* IORDY */
- if (is_slave) {
- master_data |= 0x4000;
- master_data &= ~0x0070;
- master_data = master_data | (control << 4);
- pci_read_config_byte(dev, slave_port, &slave_data);
- slave_data = slave_data & 0xf0;
- slave_data = slave_data | (timings[pio][0] << 2) | timings[pio][1];
- } else {
- master_data &= ~0x3307;
- master_data = master_data | control;
- master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8);
- }
- pci_write_config_word(dev, master_port, master_data);
- if (is_slave)
- pci_write_config_byte(dev, slave_port, slave_data);
- spin_unlock_irqrestore(&tune_lock, flags);
-}
-
-/**
- * it8213_set_dma_mode - set host controller for DMA mode
- * @hwif: port
- * @drive: drive
- *
- * Tune the ITE chipset for the DMA mode.
- */
-
-static void it8213_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 maslave = 0x40;
- int a_speed = 3 << (drive->dn * 4);
- int u_flag = 1 << drive->dn;
- int v_flag = 0x01 << drive->dn;
- int w_flag = 0x10 << drive->dn;
- int u_speed = 0;
- u16 reg4042, reg4a;
- u8 reg48, reg54, reg55;
- const u8 speed = drive->dma_mode;
-
- pci_read_config_word(dev, maslave, ®4042);
- pci_read_config_byte(dev, 0x48, ®48);
- pci_read_config_word(dev, 0x4a, ®4a);
- pci_read_config_byte(dev, 0x54, ®54);
- pci_read_config_byte(dev, 0x55, ®55);
-
- if (speed >= XFER_UDMA_0) {
- u8 udma = speed - XFER_UDMA_0;
-
- u_speed = min_t(u8, 2 - (udma & 1), udma) << (drive->dn * 4);
-
- if (!(reg48 & u_flag))
- pci_write_config_byte(dev, 0x48, reg48 | u_flag);
- if (speed >= XFER_UDMA_5)
- pci_write_config_byte(dev, 0x55, (u8) reg55|w_flag);
- else
- pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
-
- if ((reg4a & a_speed) != u_speed)
- pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
- if (speed > XFER_UDMA_2) {
- if (!(reg54 & v_flag))
- pci_write_config_byte(dev, 0x54, reg54 | v_flag);
- } else
- pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
- } else {
- const u8 mwdma_to_pio[] = { 0, 3, 4 };
-
- if (reg48 & u_flag)
- pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
- if (reg4a & a_speed)
- pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
- if (reg54 & v_flag)
- pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
- if (reg55 & w_flag)
- pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
-
- if (speed >= XFER_MW_DMA_0)
- drive->pio_mode =
- mwdma_to_pio[speed - XFER_MW_DMA_0] + XFER_PIO_0;
- else
- drive->pio_mode = XFER_PIO_2; /* for SWDMA2 */
-
- it8213_set_pio_mode(hwif, drive);
- }
-}
-
-static int it8213_cable_detect(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 reg42h = 0;
-
- pci_read_config_byte(dev, 0x42, ®42h);
-
- return (reg42h & 0x02) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
-}
+#include <linux/ide2libata.h>
+#include "../ata/pata_it8213.h"
static const struct ide_port_ops it8213_port_ops = {
- .set_pio_mode = it8213_set_pio_mode,
- .set_dma_mode = it8213_set_dma_mode,
+ .set_pio_mode = it8213_set_piomode,
+ .set_dma_mode = it8213_set_dmamode,
.cable_detect = it8213_cable_detect,
};
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
