As these drivers' set_piomode() and set_dmamode() methods are almost identical,
factor out the common hpt{37x|3x2n}_set_mode() function to be called by both of
them, the same as in 'pata_hpt366' driver.
This results in ~5% decrease in the 'pata_hpt37x' driver binary size and in ~4%
decrease in the 'pata_hpt3x2n' driver binary size (as measured on x86-32).
Signed-off-by: Sergei Shtylyov <sshtylyov@xxxxxxxxxxxxx>
---
The patch is against the recent Linus' tree.
drivers/ata/pata_hpt37x.c | 137 +++++++++++++++++++--------------------------
drivers/ata/pata_hpt3x2n.c | 69 ++++++++++------------
2 files changed, 90 insertions(+), 116 deletions(-)
Index: linux-2.6/drivers/ata/pata_hpt37x.c
===================================================================
--- linux-2.6.orig/drivers/ata/pata_hpt37x.c
+++ linux-2.6/drivers/ata/pata_hpt37x.c
@@ -24,7 +24,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt37x"
-#define DRV_VERSION "0.6.14"
+#define DRV_VERSION "0.6.15"
struct hpt_clock {
u8 xfer_speed;
@@ -377,20 +377,12 @@ static int hpt374_fn1_pre_reset(struct a
return ata_sff_prereset(link, deadline);
}
-/**
- * hpt370_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt370_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -402,11 +394,31 @@ static void hpt370_set_piomode(struct at
fast |= 0x01;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt37x_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, ®);
- mode = hpt37x_find_mode(ap, adev->pio_mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
+/**
+ * hpt370_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt370_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -414,33 +426,12 @@ static void hpt370_set_piomode(struct at
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x02;
- fast |= 0x01;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, ®);
- mode = hpt37x_find_mode(ap, adev->dma_mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt370_set_mode(ap, adev, adev->dma_mode);
}
/**
@@ -480,20 +471,12 @@ static void hpt370_bmdma_stop(struct ata
ata_bmdma_stop(qc);
}
-/**
- * hpt372_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt372_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -504,13 +487,32 @@ static void hpt372_set_piomode(struct at
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt37x_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, ®);
- mode = hpt37x_find_mode(ap, adev->pio_mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
- printk("Find mode for %d reports %X\n", adev->pio_mode, mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+/**
+ * hpt372_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt372_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -518,33 +520,12 @@ static void hpt372_set_piomode(struct at
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x07;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, ®);
- mode = hpt37x_find_mode(ap, adev->dma_mode);
- printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt372_set_mode(ap, adev, adev->dma_mode);
}
/**
Index: linux-2.6/drivers/ata/pata_hpt3x2n.c
===================================================================
--- linux-2.6.orig/drivers/ata/pata_hpt3x2n.c
+++ linux-2.6/drivers/ata/pata_hpt3x2n.c
@@ -25,7 +25,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
-#define DRV_VERSION "0.3.9"
+#define DRV_VERSION "0.3.10"
enum {
HPT_PCI_FAST = (1 << 31),
@@ -159,20 +159,12 @@ static int hpt3x2n_pre_reset(struct ata_
return ata_sff_prereset(link, deadline);
}
-/**
- * hpt3x2n_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Perform PIO mode setup.
- */
-
-static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev,
+ u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
- u32 reg;
- u32 mode;
+ u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
@@ -183,11 +175,32 @@ static void hpt3x2n_set_piomode(struct a
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
+ /* Determine timing mask and find matching mode entry */
+ if (mode < XFER_MW_DMA_0)
+ mask = 0xcfc3ffff;
+ else if (mode < XFER_UDMA_0)
+ mask = 0x31c001ff;
+ else
+ mask = 0x303c0000;
+
+ timing = hpt3x2n_find_mode(ap, mode);
+
pci_read_config_dword(pdev, addr1, ®);
- mode = hpt3x2n_find_mode(ap, adev->pio_mode);
- mode &= 0xCFC3FFFF; /* Leave DMA bits alone */
- reg &= ~0xCFC3FFFF; /* Strip timing bits */
- pci_write_config_dword(pdev, addr1, reg | mode);
+ reg = (reg & ~mask) | (timing & mask);
+ pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ * hpt3x2n_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Perform PIO mode setup.
+ */
+
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ hpt3x2n_set_mode(ap, adev, adev->pio_mode);
}
/**
@@ -195,32 +208,12 @@ static void hpt3x2n_set_piomode(struct a
* @ap: ATA interface
* @adev: Device being configured
*
- * Set up the channel for MWDMA or UDMA modes. Much the same as with
- * PIO, load the mode number and then set MWDMA or UDMA flag.
+ * Set up the channel for MWDMA or UDMA modes.
*/
static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u32 addr1, addr2;
- u32 reg, mode, mask;
- u8 fast;
-
- addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
- addr2 = 0x51 + 4 * ap->port_no;
-
- /* Fast interrupt prediction disable, hold off interrupt disable */
- pci_read_config_byte(pdev, addr2, &fast);
- fast &= ~0x07;
- pci_write_config_byte(pdev, addr2, fast);
-
- mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000;
-
- pci_read_config_dword(pdev, addr1, ®);
- mode = hpt3x2n_find_mode(ap, adev->dma_mode);
- mode &= mask;
- reg &= ~mask;
- pci_write_config_dword(pdev, addr1, reg | mode);
+ hpt3x2n_set_mode(ap, adev, adev->dma_mode);
}
/**
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
