The following changes since commit 184b8405d5d3e8510163d66efbac99d351faba2e:
Bartlomiej Zolnierkiewicz (1):
libata: add private driver field to struct ata_device
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/bart/misc.git atang-for-2.6.33
Bartlomiej Zolnierkiewicz (28):
ide-pci-generic: build fix
ata_piix: fix MWDMA handling on PIIX3
pata_efar: fix wrong PIO timings being programmed
pata_efar: fix wrong MWDMA timings being programmed
pata_efar: MWDMA0 is unsupported
pata_cmd640: document known issues
pata_cs5520: remove dead VDMA support
pata_cypress: document known issues
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_hpt3x3: Power Management fix
pata_it8213: fix UDMA handling
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: MWDMA0 is unsupported
pata_legacy: fix QDI6580DP support
pata_legacy: fix access to control register for QDI6580
pata_legacy: add pointers to QDI65x0 documentation
pata_marvell: fix marvell_pre_reset() documentation
pata_ns87415: Power Management fix
pata_oldpiix: MWDMA0 is unsupported
pata_pdc202xx_old: document known issues
pata_radisys: fix UDMA handling
pata_rdc: MWDMA0 is unsupported
pata_rz1000: Power Management fix
pata_sis: Power Management fix
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
drivers/ata/Kconfig | 14 ++++++++++++--
drivers/ata/ata_piix.c | 6 +++---
drivers/ata/pata_cs5520.c | 39 +--------------------------------------
drivers/ata/pata_efar.c | 9 +++++----
drivers/ata/pata_hpt3x2n.c | 3 +--
drivers/ata/pata_hpt3x3.c | 11 ++++++++++-
drivers/ata/pata_it8213.c | 27 +++++++++++++--------------
drivers/ata/pata_legacy.c | 14 +++++++++++---
drivers/ata/pata_marvell.c | 2 +-
drivers/ata/pata_ns87415.c | 32 +++++++++++++++++++++++++++-----
drivers/ata/pata_oldpiix.c | 2 +-
drivers/ata/pata_radisys.c | 4 ++--
drivers/ata/pata_rdc.c | 2 +-
drivers/ata/pata_rz1000.c | 11 ++++++++++-
drivers/ata/pata_sis.c | 21 +++++++++++++++++++--
drivers/ata/pata_via.c | 19 +++++++++++++------
drivers/ide/ide-pci-generic.c | 2 +-
17 files changed, 131 insertions(+), 87 deletions(-)
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 676f08b..25cb4e7 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -287,8 +287,11 @@ config PATA_CMD640_PCI
depends on PCI && EXPERIMENTAL
help
This option enables support for the CMD640 PCI IDE
- interface chip. Only the primary channel is currently
- supported.
+ interface chip.
+
+ Known issues:
+ - only the primary channel is currently supported
+ - only the PCI chip interface is currently supported
If unsure, say N.
@@ -344,6 +347,9 @@ config PATA_CYPRESS
This option enables support for the Cypress/Contaq CY82C693
chipset found in some Alpha systems
+ Known issues:
+ - only the primary channel is currently supported
+
If unsure, say N.
config PATA_EFAR
@@ -588,6 +594,10 @@ config PATA_PDC_OLD
This option enables support for the Promise 20246, 20262, 20263,
20265 and 20267 adapters.
+ Known issues:
+ - UDMA transfers fail mysteriously on some chipsets
+ - ATAPI DMA is unsupported currently
+
If unsure, say N.
config PATA_QDI
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 9ac4e37..0c6155f 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -869,10 +869,10 @@ static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, in
(timings[pio][1] << 8);
}
- if (ap->udma_mask) {
+ if (ap->udma_mask)
udma_enable &= ~(1 << devid);
- pci_write_config_word(dev, master_port, master_data);
- }
+
+ pci_write_config_word(dev, master_port, master_data);
}
/* Don't scribble on 0x48 if the controller does not support UDMA */
if (ap->udma_mask)
diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c
index 0df83cf..95ebdac 100644
--- a/drivers/ata/pata_cs5520.c
+++ b/drivers/ata/pata_cs5520.c
@@ -90,48 +90,12 @@ static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int
}
/**
- * cs5520_enable_dma - turn on DMA bits
- *
- * Turn on the DMA bits for this disk. Needed because the BIOS probably
- * has not done the work for us. Belongs in the core SATA code.
- */
-
-static void cs5520_enable_dma(struct ata_port *ap, struct ata_device *adev)
-{
- /* Set the DMA enable/disable flag */
- u8 reg = ioread8(ap->ioaddr.bmdma_addr + 0x02);
- reg |= 1<<(adev->devno + 5);
- iowrite8(reg, ap->ioaddr.bmdma_addr + 0x02);
-}
-
-/**
- * cs5520_set_dmamode - program DMA timings
- * @ap: ATA port
- * @adev: ATA device
- *
- * Program the DMA mode timings for the controller according to the pio
- * clocking table. Note that this device sets the DMA timings to PIO
- * mode values. This may seem bizarre but the 5520 architecture talks
- * PIO mode to the disk and DMA mode to the controller so the underlying
- * transfers are PIO timed.
- */
-
-static void cs5520_set_dmamode(struct ata_port *ap, struct ata_device *adev)
-{
- static const int dma_xlate[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 };
- cs5520_set_timings(ap, adev, dma_xlate[adev->dma_mode]);
- cs5520_enable_dma(ap, adev);
-}
-
-/**
* cs5520_set_piomode - program PIO timings
* @ap: ATA port
* @adev: ATA device
*
* Program the PIO mode timings for the controller according to the pio
- * clocking table. We know pio_mode will equal dma_mode because of the
- * CS5520 architecture. At least once we turned DMA on and wrote a
- * mode setter.
+ * clocking table.
*/
static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev)
@@ -149,7 +113,6 @@ static struct ata_port_operations cs5520_port_ops = {
.qc_prep = ata_sff_dumb_qc_prep,
.cable_detect = ata_cable_40wire,
.set_piomode = cs5520_set_piomode,
- .set_dmamode = cs5520_set_dmamode,
};
static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c
index 2a6412f..b2e71e6 100644
--- a/drivers/ata/pata_efar.c
+++ b/drivers/ata/pata_efar.c
@@ -2,6 +2,7 @@
* pata_efar.c - EFAR PIIX clone controller driver
*
* (C) 2005 Red Hat
+ * (C) 2009 Bartlomiej Zolnierkiewicz
*
* Some parts based on ata_piix.c by Jeff Garzik and others.
*
@@ -118,12 +119,12 @@ static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev)
int shift = 4 * ap->port_no;
u8 slave_data;
- idetm_data &= 0xCC0F;
+ idetm_data &= 0xFF0F;
idetm_data |= (control << 4);
/* Slave timing in separate register */
pci_read_config_byte(dev, 0x44, &slave_data);
- slave_data &= 0x0F << shift;
+ slave_data &= ap->port_no ? 0x0F : 0xF0;
slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << shift;
pci_write_config_byte(dev, 0x44, slave_data);
}
@@ -200,7 +201,7 @@ static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev)
master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
master_data |= control << 4;
pci_read_config_byte(dev, 0x44, &slave_data);
- slave_data &= (0x0F + 0xE1 * ap->port_no);
+ slave_data &= ap->port_no ? 0x0F : 0xF0;
/* Load the matching timing */
slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
pci_write_config_byte(dev, 0x44, slave_data);
@@ -251,7 +252,7 @@ static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
+ .mwdma_mask = ATA_MWDMA12_ONLY,
.udma_mask = ATA_UDMA4,
.port_ops = &efar_ops,
};
diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
index d30da80..9a09a1b 100644
--- a/drivers/ata/pata_hpt3x2n.c
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -80,14 +80,13 @@ static struct hpt_clock hpt3x2n_clocks[] = {
{ XFER_MW_DMA_2, 0x2c829c62 },
{ XFER_MW_DMA_1, 0x2c829c66 },
- { XFER_MW_DMA_0, 0x2c829d2c },
+ { XFER_MW_DMA_0, 0x2c829d2e },
{ XFER_PIO_4, 0x0c829c62 },
{ XFER_PIO_3, 0x0c829c84 },
{ XFER_PIO_2, 0x0c829ca6 },
{ XFER_PIO_1, 0x0d029d26 },
{ XFER_PIO_0, 0x0d029d5e },
- { 0, 0x0d029d5e }
};
/**
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
index 7e31025..c86c716 100644
--- a/drivers/ata/pata_hpt3x3.c
+++ b/drivers/ata/pata_hpt3x3.c
@@ -255,8 +255,17 @@ static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
#ifdef CONFIG_PM
static int hpt3x3_reinit_one(struct pci_dev *dev)
{
+ struct ata_host *host = dev_get_drvdata(&dev->dev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(dev);
+ if (rc)
+ return rc;
+
hpt3x3_init_chipset(dev);
- return ata_pci_device_resume(dev);
+
+ ata_host_resume(host);
+ return 0;
}
#endif
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c
index f156da8..8f3325a 100644
--- a/drivers/ata/pata_it8213.c
+++ b/drivers/ata/pata_it8213.c
@@ -22,7 +22,7 @@
#define DRV_VERSION "0.0.3"
/**
- * it8213_pre_reset - check for 40/80 pin
+ * it8213_pre_reset - probe begin
* @link: link
* @deadline: deadline jiffies for the operation
*
@@ -92,18 +92,17 @@ static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
{ 2, 1 },
{ 2, 3 }, };
- if (pio > 2)
- control |= 1; /* TIME1 enable */
+ if (pio > 1)
+ control |= 1; /* TIME */
if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */
- control |= 2; /* IORDY enable */
+ control |= 2; /* IE */
/* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */
if (adev->class != ATA_DEV_ATA)
- control |= 4;
+ control |= 4; /* PPE */
pci_read_config_word(dev, idetm_port, &idetm_data);
- /* Enable PPE, IE and TIME as appropriate */
-
+ /* Set PPE, IE, and TIME as appropriate */
if (adev->devno == 0) {
idetm_data &= 0xCCF0;
idetm_data |= control;
@@ -112,17 +111,17 @@ static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
} else {
u8 slave_data;
- idetm_data &= 0xCC0F;
+ idetm_data &= 0xFF0F;
idetm_data |= (control << 4);
/* Slave timing in separate register */
pci_read_config_byte(dev, 0x44, &slave_data);
slave_data &= 0xF0;
- slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << 4;
+ slave_data |= (timings[pio][0] << 2) | timings[pio][1];
pci_write_config_byte(dev, 0x44, slave_data);
}
- idetm_data |= 0x4000; /* Ensure SITRE is enabled */
+ idetm_data |= 0x4000; /* Ensure SITRE is set */
pci_write_config_word(dev, idetm_port, idetm_data);
}
@@ -173,10 +172,10 @@ static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev)
udma_enable |= (1 << devid);
- /* Load the UDMA mode number */
+ /* Load the UDMA cycle time */
pci_read_config_word(dev, 0x4A, &udma_timing);
udma_timing &= ~(3 << (4 * devid));
- udma_timing |= (udma & 3) << (4 * devid);
+ udma_timing |= u_speed << (4 * devid);
pci_write_config_word(dev, 0x4A, udma_timing);
/* Load the clock selection */
@@ -211,7 +210,7 @@ static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev)
master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
master_data |= control << 4;
pci_read_config_byte(dev, 0x44, &slave_data);
- slave_data &= (0x0F + 0xE1 * ap->port_no);
+ slave_data &= 0xF0;
/* Load the matching timing */
slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
pci_write_config_byte(dev, 0x44, slave_data);
@@ -263,7 +262,7 @@ static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *en
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
+ .mwdma_mask = ATA_MWDMA12_ONLY,
.udma_mask = ATA_UDMA4, /* FIXME: want UDMA 100? */
.port_ops = &it8213_ops,
};
diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c
index 6932e56..9df1ff7 100644
--- a/drivers/ata/pata_legacy.c
+++ b/drivers/ata/pata_legacy.c
@@ -25,6 +25,13 @@
* http://www.ryston.cz/petr/vlb/pdc20230b.html
* http://www.ryston.cz/petr/vlb/pdc20230c.html
* http://www.ryston.cz/petr/vlb/pdc20630.html
+ * QDI65x0:
+ * http://www.ryston.cz/petr/vlb/qd6500.html
+ * http://www.ryston.cz/petr/vlb/qd6580.html
+ *
+ * QDI65x0 probe code based on drivers/ide/legacy/qd65xx.c
+ * Rewritten from the work of Colten Edwards <pje120@xxxxxxxxxxx> by
+ * Samuel Thibault <samuel.thibault@xxxxxxxxxxxx>
*
* Unsupported but docs exist:
* Appian/Adaptec AIC25VL01/Cirrus Logic PD7220
@@ -35,7 +42,7 @@
* the MPIIX where the tuning is PCI side but the IDE is "ISA side".
*
* Specific support is included for the ht6560a/ht6560b/opti82c611a/
- * opti82c465mv/promise 20230c/20630/winbond83759A
+ * opti82c465mv/promise 20230c/20630/qdi65x0/winbond83759A
*
* Use the autospeed and pio_mask options with:
* Appian ADI/2 aka CLPD7220 or AIC25VL01.
@@ -672,7 +679,7 @@ static void qdi6580dp_set_piomode(struct ata_port *ap, struct ata_device *adev)
outb(timing, ld_qdi->timing + 2 * ap->port_no);
/* Clear the FIFO */
if (adev->class != ATA_DEV_ATA)
- outb(0x5F, ld_qdi->timing + 3);
+ outb(0x5F, (ld_qdi->timing & 0xFFF0) + 3);
}
/**
@@ -707,7 +714,7 @@ static void qdi6580_set_piomode(struct ata_port *ap, struct ata_device *adev)
outb(timing, ld_qdi->timing + 2 * adev->devno);
/* Clear the FIFO */
if (adev->class != ATA_DEV_ATA)
- outb(0x5F, ld_qdi->timing + 3);
+ outb(0x5F, (ld_qdi->timing & 0xFFF0) + 3);
}
/**
@@ -787,6 +794,7 @@ static struct ata_port_operations qdi6580_port_ops = {
static struct ata_port_operations qdi6580dp_port_ops = {
.inherits = &legacy_base_port_ops,
.set_piomode = qdi6580dp_set_piomode,
+ .qc_issue = qdi_qc_issue,
.sff_data_xfer = vlb32_data_xfer,
};
diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c
index 2096fb7..950da39 100644
--- a/drivers/ata/pata_marvell.c
+++ b/drivers/ata/pata_marvell.c
@@ -58,7 +58,7 @@ static int marvell_pata_active(struct pci_dev *pdev)
}
/**
- * marvell_pre_reset - check for 40/80 pin
+ * marvell_pre_reset - probe begin
* @link: link
* @deadline: deadline jiffies for the operation
*
diff --git a/drivers/ata/pata_ns87415.c b/drivers/ata/pata_ns87415.c
index 773b159..061aa1c 100644
--- a/drivers/ata/pata_ns87415.c
+++ b/drivers/ata/pata_ns87415.c
@@ -325,6 +325,13 @@ static struct scsi_host_template ns87415_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
+static void ns87415_fixup(struct pci_dev *pdev)
+{
+ /* Select 512 byte sectors */
+ pci_write_config_byte(pdev, 0x55, 0xEE);
+ /* Select PIO0 8bit clocking */
+ pci_write_config_byte(pdev, 0x54, 0xB7);
+}
/**
* ns87415_init_one - Register 87415 ATA PCI device with kernel services
@@ -371,10 +378,8 @@ static int ns87415_init_one (struct pci_dev *pdev, const struct pci_device_id *e
if (rc)
return rc;
- /* Select 512 byte sectors */
- pci_write_config_byte(pdev, 0x55, 0xEE);
- /* Select PIO0 8bit clocking */
- pci_write_config_byte(pdev, 0x54, 0xB7);
+ ns87415_fixup(pdev);
+
return ata_pci_sff_init_one(pdev, ppi, &ns87415_sht, NULL);
}
@@ -384,6 +389,23 @@ static const struct pci_device_id ns87415_pci_tbl[] = {
{ } /* terminate list */
};
+#ifdef CONFIG_PM
+static int ns87415_reinit_one(struct pci_dev *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+
+ ns87415_fixup(pdev);
+
+ ata_host_resume(host);
+ return 0;
+}
+#endif
+
static struct pci_driver ns87415_pci_driver = {
.name = DRV_NAME,
.id_table = ns87415_pci_tbl,
@@ -391,7 +413,7 @@ static struct pci_driver ns87415_pci_driver = {
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
- .resume = ata_pci_device_resume,
+ .resume = ns87415_reinit_one,
#endif
};
diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c
index 84ac503..9a8687d 100644
--- a/drivers/ata/pata_oldpiix.c
+++ b/drivers/ata/pata_oldpiix.c
@@ -239,7 +239,7 @@ static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *e
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
+ .mwdma_mask = ATA_MWDMA12_ONLY,
.port_ops = &oldpiix_pata_ops,
};
const struct ata_port_info *ppi[] = { &info, NULL };
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
index 4401b33..4fd25e7 100644
--- a/drivers/ata/pata_radisys.c
+++ b/drivers/ata/pata_radisys.c
@@ -139,9 +139,9 @@ static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
pci_read_config_byte(dev, 0x4A, &udma_mode);
if (adev->xfer_mode == XFER_UDMA_2)
- udma_mode &= ~ (1 << adev->devno);
+ udma_mode &= ~(2 << (adev->devno * 4));
else /* UDMA 4 */
- udma_mode |= (1 << adev->devno);
+ udma_mode |= (2 << (adev->devno * 4));
pci_write_config_byte(dev, 0x4A, udma_mode);
diff --git a/drivers/ata/pata_rdc.c b/drivers/ata/pata_rdc.c
index c843a1e..237a24d 100644
--- a/drivers/ata/pata_rdc.c
+++ b/drivers/ata/pata_rdc.c
@@ -284,7 +284,7 @@ static struct ata_port_info rdc_port_info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
- .mwdma_mask = ATA_MWDMA2,
+ .mwdma_mask = ATA_MWDMA12_ONLY,
.udma_mask = ATA_UDMA5,
.port_ops = &rdc_pata_ops,
};
diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c
index a5e4dfe..2932998 100644
--- a/drivers/ata/pata_rz1000.c
+++ b/drivers/ata/pata_rz1000.c
@@ -105,11 +105,20 @@ static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *en
#ifdef CONFIG_PM
static int rz1000_reinit_one(struct pci_dev *pdev)
{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+
/* If this fails on resume (which is a "cant happen" case), we
must stop as any progress risks data loss */
if (rz1000_fifo_disable(pdev))
panic("rz1000 fifo");
- return ata_pci_device_resume(pdev);
+
+ ata_host_resume(host);
+ return 0;
}
#endif
diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c
index d70ecec..8af0dc8 100644
--- a/drivers/ata/pata_sis.c
+++ b/drivers/ata/pata_sis.c
@@ -2,7 +2,7 @@
* pata_sis.c - SiS ATA driver
*
* (C) 2005 Red Hat
- * (C) 2007 Bartlomiej Zolnierkiewicz
+ * (C) 2007,2009 Bartlomiej Zolnierkiewicz
*
* Based upon linux/drivers/ide/pci/sis5513.c
* Copyright (C) 1999-2000 Andre Hedrick <andre@xxxxxxxxxxxxx>
@@ -876,6 +876,23 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
return ata_pci_sff_init_one(pdev, ppi, &sis_sht, chipset);
}
+#ifdef CONFIG_PM
+static int sis_reinit_one(struct pci_dev *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+
+ sis_fixup(pdev, host->private_data);
+
+ ata_host_resume(host);
+ return 0;
+}
+#endif
+
static const struct pci_device_id sis_pci_tbl[] = {
{ PCI_VDEVICE(SI, 0x5513), }, /* SiS 5513 */
{ PCI_VDEVICE(SI, 0x5518), }, /* SiS 5518 */
@@ -891,7 +908,7 @@ static struct pci_driver sis_pci_driver = {
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
- .resume = ata_pci_device_resume,
+ .resume = sis_reinit_one,
#endif
};
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c
index 78eac27..0d97890 100644
--- a/drivers/ata/pata_via.c
+++ b/drivers/ata/pata_via.c
@@ -303,14 +303,21 @@ static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mo
}
/* Set UDMA unless device is not UDMA capable */
- if (udma_type && t.udma) {
- u8 cable80_status;
+ if (udma_type) {
+ u8 udma_etc;
- /* Get 80-wire cable detection bit */
- pci_read_config_byte(pdev, 0x50 + offset, &cable80_status);
- cable80_status &= 0x10;
+ pci_read_config_byte(pdev, 0x50 + offset, &udma_etc);
- pci_write_config_byte(pdev, 0x50 + offset, ut | cable80_status);
+ /* clear transfer mode bit */
+ udma_etc &= ~0x20;
+
+ if (t.udma) {
+ /* preserve 80-wire cable detection bit */
+ udma_etc &= 0x10;
+ udma_etc |= ut;
+ }
+
+ pci_write_config_byte(pdev, 0x50 + offset, udma_etc);
}
}
diff --git a/drivers/ide/ide-pci-generic.c b/drivers/ide/ide-pci-generic.c
index 3f0bc42..a743e68 100644
--- a/drivers/ide/ide-pci-generic.c
+++ b/drivers/ide/ide-pci-generic.c
@@ -165,7 +165,7 @@ static const struct pci_device_id generic_pci_tbl[] = {
{ PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), 4 },
{ PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), 4 },
{ PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_3), 4 },
- { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_5) 4 },
+ { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_5), 4 },
{ PCI_VDEVICE(NETCELL, PCI_DEVICE_ID_REVOLUTION), 6 },
/*
* Must come last. If you add entries adjust
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
