Thanks for the reply Tejun. I gave the 2.6.30-2 kernel a try and I received the same error message as quoted below - it just happened a bit later on in the boot process. (not at the "starting.." screen) Chris. On Wed, Aug 12, 2009 at 12:19 AM, Tejun Heo <htejun@xxxxxxxxx> wrote: > > Chris K wrote: > > Hello Tejun, > > > > I was hoping you'd have some feedback or suggestions relating to the > > eSata port multiplier errors I am receiving below. > > > > I have a Silicone Image 3132 chipset (PCI-E 2-port eSATA controller > > card) and a Sans Digital TRM4-B 4x hard drive enclosure with 4x 1TB WD > > Caviar Green drives. I am having difficulty getting drives detected with > > eSATA and Port Multiplier (PMP) in Ubuntu 9.04 running the > > 2.6.28-14-server (or generic) kernel. I've also tried > > 2.6.28-11-server/generic and 2.6.31-5-generic with no luck . > > > > On a Windows machine everything works correctly. When I boot my Ubuntu > > machine (or plug in the eSATA cable), it scans the external drives > > repeatedly (LEDs go on an off a number of times) and eventually times > > out with the following messages: > > > > [59719.989422] ata7: irq_stat 0x01100010, PHY RDY changed > > [59719.989477] ata7: SError: { 10B8B } > > [59722.781043] ata7: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe > > frozen > > [59722.781112] ata7: irq_stat 0x00b40090, PHY RDY changed > > [59791.300259] ata7.15: failed to write PMP_FEAT_EN (Emask=0x40) > > [59791.300324] ata7: failed to recover PMP after 5 tries, giving up > > [59791.300323] ata7: exception Emask 0x3 SAct 0x0 SErr 0x0 action 0x6 > > frozen t4 > > [59791.300483] ata7: irq_stat 0x00060002, device error via D2H FIS > > > > I've attached my dmesg as well. Any help would be greatly appreciated. > > * Can you please cc linux-ide@xxxxxxxxxxxxxxx? > > * Can you please try 2.6.30? > > Thanks. > > -- > tejun
[ 0.000000] BIOS EBDA/lowmem at: 0009e800/0009e800 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.28-14-server (buildd@palmer) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #47-Ubuntu SMP Sat Jul 25 01:18:34 UTC 2009 (Ubuntu 2.6.28-14.47-server) [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 0000000060000000 (usable) [ 0.000000] BIOS-e820: 0000000060000000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 0000000080000000 - 000000009fef0000 (usable) [ 0.000000] BIOS-e820: 000000009fef0000 - 000000009fef3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000009fef3000 - 000000009ff00000 (ACPI data) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000e2000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable) [ 0.000000] DMI 2.4 present. [ 0.000000] last_pfn = 0x140000 max_arch_pfn = 0x1000000 [ 0.000000] Scanning 2 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000002000 (usable) [ 0.000000] modified: 0000000000002000 - 0000000000006000 (reserved) [ 0.000000] modified: 0000000000006000 - 0000000000007000 (usable) [ 0.000000] modified: 0000000000007000 - 0000000000010000 (reserved) [ 0.000000] modified: 0000000000010000 - 0000000000091800 (usable) [ 0.000000] modified: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] modified: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 0000000060000000 (usable) [ 0.000000] modified: 0000000060000000 - 0000000080000000 (reserved) [ 0.000000] modified: 0000000080000000 - 000000009fef0000 (usable) [ 0.000000] modified: 000000009fef0000 - 000000009fef3000 (ACPI NVS) [ 0.000000] modified: 000000009fef3000 - 000000009ff00000 (ACPI data) [ 0.000000] modified: 00000000e0000000 - 00000000e2000000 (reserved) [ 0.000000] modified: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] modified: 0000000100000000 - 0000000140000000 (usable) [ 0.000000] kernel direct mapping tables up to 377fe000 @ 10000-16000 [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] RAMDISK: 37870000 - 37fef355 [ 0.000000] Allocated new RAMDISK: 008ab000 - 0102a355 [ 0.000000] Move RAMDISK from 0000000037870000 - 0000000037fef354 to 008ab000 - 0102a354 [ 0.000000] ACPI: RSDP 000F64D0, 0014 (r0 GBT ) [ 0.000000] ACPI: RSDT 9FEF3040, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) [ 0.000000] ACPI: FACP 9FEF30C0, 0074 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) [ 0.000000] ACPI: DSDT 9FEF3180, 79C9 (r1 GBT GBTUACPI 1000 MSFT 3000000) [ 0.000000] ACPI: FACS 9FEF1800, 0040 [ 0.000000] ACPI: HPET 9FEFACC0, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 98) [ 0.000000] ACPI: MCFG 9FEFAD40, 003C (r1 GBT GBTUACPI 42302E31 GBTU 1010101) [ 0.000000] ACPI: APIC 9FEFABC0, 0098 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) [ 0.000000] ACPI: SSDT 9FEFB3E0, 03AB (r1 PmRef CpuPm 3000 INTL 20040311) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] 4232MB HIGHMEM available. [ 0.000000] 887MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 377fe000 [ 0.000000] low ram: 00000000 - 377fe000 [ 0.000000] bootmap 00013000 - 00019f00 [ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] [ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] [ 0.000000] #3 [0000100000 - 00008a19ac] TEXT DATA BSS ==> [0000100000 - 00008a19ac] [ 0.000000] #4 [00008a2000 - 00008ab000] INIT_PG_TABLE ==> [00008a2000 - 00008ab000] [ 0.000000] #5 [000009e800 - 0000100000] BIOS reserved ==> [000009e800 - 0000100000] [ 0.000000] #6 [0000010000 - 0000013000] PGTABLE ==> [0000010000 - 0000013000] [ 0.000000] #7 [00008ab000 - 000102a355] NEW RAMDISK ==> [00008ab000 - 000102a355] [ 0.000000] #8 [0000013000 - 000001a000] BOOTMAP ==> [0000013000 - 000001a000] [ 0.000000] found SMP MP-table at [c00f4b90] 000f4b90 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00001000 [ 0.000000] Normal 0x00001000 -> 0x000377fe [ 0.000000] HighMem 0x000377fe -> 0x00140000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[6] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00000002 [ 0.000000] 0: 0x00000006 -> 0x00000007 [ 0.000000] 0: 0x00000010 -> 0x00000091 [ 0.000000] 0: 0x00000100 -> 0x00060000 [ 0.000000] 0: 0x00080000 -> 0x0009fef0 [ 0.000000] 0: 0x00100000 -> 0x00140000 [ 0.000000] On node 0 totalpages: 786036 [ 0.000000] free_area_init_node: node 0, pgdat c06dea00, node_mem_map c102b000 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3940 pages, LIFO batch:0 [ 0.000000] Normal zone: 1744 pages used for memmap [ 0.000000] Normal zone: 221486 pages, LIFO batch:31 [ 0.000000] HighMem zone: 8465 pages used for memmap [ 0.000000] HighMem zone: 550369 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfeff0000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs [ 0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000 [ 0.000000] PM: Registered nosave memory: 0000000000007000 - 0000000000010000 [ 0.000000] PM: Registered nosave memory: 0000000000091000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at a0000000 (gap: 9ff00000:40100000) [ 0.000000] PERCPU: Allocating 49152 bytes of per cpu data [ 0.000000] NR_CPUS: 64, nr_cpu_ids: 4, nr_node_ids 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 775795 [ 0.000000] Kernel command line: root=UUID=4d2c3811-2cee-426f-a6aa-f2f318fbca93 ro quiet splash quiet [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 2499.645 MHz processor. [ 0.010000] spurious 8259A interrupt: IRQ7. [ 0.010000] Console: colour VGA+ 80x25 [ 0.010000] console [tty0] enabled [ 0.010000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.010000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.010000] allocated 26214400 bytes of page_cgroup [ 0.010000] please try cgroup_disable=memory option if you don't want [ 0.010000] Scanning for low memory corruption every 60 seconds [ 0.010000] Memory: 3060048k/5242880k available (4168k kernel code, 83184k reserved, 2239k data, 544k init, 2235336k highmem) [ 0.010000] virtual kernel memory layout: [ 0.010000] fixmap : 0xffc78000 - 0xfffff000 (3612 kB) [ 0.010000] pkmap : 0xff800000 - 0xffa00000 (2048 kB) [ 0.010000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB) [ 0.010000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB) [ 0.010000] .init : 0xc0749000 - 0xc07d1000 ( 544 kB) [ 0.010000] .data : 0xc0512393 - 0xc0741fc0 (2239 kB) [ 0.010000] .text : 0xc0100000 - 0xc0512393 (4168 kB) [ 0.010000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.010000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.010000] hpet clockevent registered [ 0.010000] HPET: 4 timers in total, 0 timers will be used for per-cpu timer [ 0.010000] Calibrating delay loop (skipped), value calculated using timer frequency.. 4999.29 BogoMIPS (lpj=24996450) [ 0.010000] Security Framework initialized [ 0.010000] SELinux: Disabled at boot. [ 0.010000] AppArmor: AppArmor initialized [ 0.010000] Mount-cache hash table entries: 512 [ 0.010000] Initializing cgroup subsys ns [ 0.010000] Initializing cgroup subsys cpuacct [ 0.010000] Initializing cgroup subsys memory [ 0.010000] Initializing cgroup subsys freezer [ 0.010000] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.010000] CPU: L2 cache: 2048K [ 0.010000] CPU: Physical Processor ID: 0 [ 0.010000] CPU: Processor Core ID: 0 [ 0.010000] using mwait in idle threads. [ 0.010000] Checking 'hlt' instruction... OK. [ 0.042347] ACPI: Core revision 20080926 [ 0.045716] ACPI: Checking initramfs for custom DSDT [ 0.347508] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.447516] CPU0: Intel Pentium(R) Dual-Core CPU E5200 @ 2.50GHz stepping 0a [ 0.450000] Booting processor 1 APIC 0x1 ip 0x6000 [ 0.010000] Initializing CPU#1 [ 0.010000] Calibrating delay using timer specific routine.. 4999.91 BogoMIPS (lpj=24999562) [ 0.010000] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.010000] CPU: L2 cache: 2048K [ 0.010000] CPU: Physical Processor ID: 0 [ 0.010000] CPU: Processor Core ID: 1 [ 0.600448] CPU1: Intel Pentium(R) Dual-Core CPU E5200 @ 2.50GHz stepping 0a [ 0.600463] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 0.610039] Brought up 2 CPUs [ 0.610041] Total of 2 processors activated (9999.20 BogoMIPS). [ 0.610107] CPU0 attaching sched-domain: [ 0.610109] domain 0: span 0-1 level MC [ 0.610111] groups: 0 1 [ 0.610116] CPU1 attaching sched-domain: [ 0.610117] domain 0: span 0-1 level MC [ 0.610119] groups: 1 0 [ 0.610182] net_namespace: 776 bytes [ 0.610182] Booting paravirtualized kernel on bare hardware [ 0.610280] Time: 22:21:36 Date: 08/12/09 [ 0.610280] regulator: core version 0.5 [ 0.610280] NET: Registered protocol family 16 [ 0.610280] EISA bus registered [ 0.610280] ACPI: bus type pci registered [ 0.610280] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 31 [ 0.610280] PCI: MCFG area at e0000000 reserved in E820 [ 0.610280] PCI: Using MMCONFIG for extended config space [ 0.610280] PCI: Using configuration type 1 for base access [ 0.610284] mtrr: your CPUs had inconsistent fixed MTRR settings [ 0.610286] mtrr: probably your BIOS does not setup all CPUs. [ 0.610287] mtrr: corrected configuration. [ 0.611180] ACPI: EC: Look up EC in DSDT [ 0.626764] ACPI: Interpreter enabled [ 0.626770] ACPI: (supports S0 S3 S4 S5) [ 0.626785] ACPI: Using IOAPIC for interrupt routing [ 0.643923] ACPI: No dock devices found. [ 0.643934] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.644251] pci 0000:00:03.2: reg 10 io port: [0xdc00-0xdc3f] [ 0.644265] pci 0000:00:03.2: reg 20 io port: [0x1c00-0x1c3f] [ 0.644270] pci 0000:00:03.2: reg 24 io port: [0x1c80-0x1cbf] [ 0.644282] pci 0000:00:03.2: PME# supported from D3hot D3cold [ 0.644287] pci 0000:00:03.2: PME# disabled [ 0.644445] pci 0000:00:03.5: reg 10 32bit mmio: [0xe6000000-0xe607ffff] [ 0.644531] pci 0000:00:04.0: reg 10 32bit mmio: [0xe608c000-0xe608cfff] [ 0.644556] pci 0000:00:04.0: supports D1 D2 [ 0.644557] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.644560] pci 0000:00:04.0: PME# disabled [ 0.644588] pci 0000:00:04.1: reg 10 32bit mmio: [0xe6089000-0xe60890ff] [ 0.644615] pci 0000:00:04.1: supports D1 D2 [ 0.644616] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot D3cold [ 0.644619] pci 0000:00:04.1: PME# disabled [ 0.644651] pci 0000:00:06.0: reg 10 32bit mmio: [0xe608a000-0xe608afff] [ 0.644676] pci 0000:00:06.0: supports D1 D2 [ 0.644677] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.644680] pci 0000:00:06.0: PME# disabled [ 0.644708] pci 0000:00:06.1: reg 10 32bit mmio: [0xe608b000-0xe608b0ff] [ 0.644735] pci 0000:00:06.1: supports D1 D2 [ 0.644736] pci 0000:00:06.1: PME# supported from D0 D1 D2 D3hot D3cold [ 0.644739] pci 0000:00:06.1: PME# disabled [ 0.644771] pci 0000:00:08.0: reg 10 32bit mmio: [0xe6080000-0xe6083fff] [ 0.644796] pci 0000:00:08.0: PME# supported from D3hot D3cold [ 0.644799] pci 0000:00:08.0: PME# disabled [ 0.644854] pci 0000:00:0a.0: reg 10 32bit mmio: [0xe6086000-0xe6086fff] [ 0.644858] pci 0000:00:0a.0: reg 14 io port: [0xc400-0xc407] [ 0.644863] pci 0000:00:0a.0: reg 18 32bit mmio: [0xe6087000-0xe60870ff] [ 0.644867] pci 0000:00:0a.0: reg 1c 32bit mmio: [0xe6088000-0xe608800f] [ 0.644882] pci 0000:00:0a.0: supports D1 D2 [ 0.644883] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.644887] pci 0000:00:0a.0: PME# disabled [ 0.644915] pci 0000:00:0b.0: reg 10 io port: [0x9f0-0x9f7] [ 0.644919] pci 0000:00:0b.0: reg 14 io port: [0xbf0-0xbf3] [ 0.644923] pci 0000:00:0b.0: reg 18 io port: [0x970-0x977] [ 0.644927] pci 0000:00:0b.0: reg 1c io port: [0xb70-0xb73] [ 0.644931] pci 0000:00:0b.0: reg 20 io port: [0xd800-0xd80f] [ 0.644935] pci 0000:00:0b.0: reg 24 32bit mmio: [0xe6084000-0xe6085fff] [ 0.644981] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.644983] pci 0000:00:10.0: PME# disabled [ 0.645126] pci 0000:00:15.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.645133] pci 0000:00:15.0: PME# disabled [ 0.645215] pci 0000:00:09.0: transparent bridge [ 0.645218] pci 0000:00:09.0: bridge io port: [0x9000-0x9fff] [ 0.645251] pci 0000:02:00.0: reg 10 32bit mmio: [0xe2000000-0xe2ffffff] [ 0.645259] pci 0000:02:00.0: reg 14 64bit mmio: [0xc0000000-0xcfffffff] [ 0.645267] pci 0000:02:00.0: reg 1c 64bit mmio: [0xd0000000-0xd1ffffff] [ 0.645273] pci 0000:02:00.0: reg 24 io port: [0xa000-0xa07f] [ 0.645278] pci 0000:02:00.0: reg 30 32bit mmio: [0x000000-0x01ffff] [ 0.645317] pci 0000:00:10.0: bridge io port: [0xa000-0xafff] [ 0.645320] pci 0000:00:10.0: bridge 32bit mmio: [0xe2000000-0xe3ffffff] [ 0.645324] pci 0000:00:10.0: bridge 64bit mmio pref: [0xc0000000-0xdfffffff] [ 0.645380] pci 0000:03:00.0: reg 10 64bit mmio: [0xe5004000-0xe500407f] [ 0.645394] pci 0000:03:00.0: reg 18 64bit mmio: [0xe5000000-0xe5003fff] [ 0.645401] pci 0000:03:00.0: reg 20 io port: [0xb000-0xb07f] [ 0.645415] pci 0000:03:00.0: reg 30 32bit mmio: [0x000000-0x07ffff] [ 0.645426] pci 0000:03:00.0: supports D1 D2 [ 0.645487] pci 0000:00:15.0: bridge io port: [0xb000-0xbfff] [ 0.645495] pci 0000:00:15.0: bridge 32bit mmio: [0xe4000000-0xe5ffffff] [ 0.645529] bus 00 -> node 0 [ 0.645534] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.646042] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 0.756505] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.756720] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.756933] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.757146] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.757360] ACPI: PCI Interrupt Link [LE0A] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.757573] ACPI: PCI Interrupt Link [LE0B] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.757786] ACPI: PCI Interrupt Link [LE0C] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.757999] ACPI: PCI Interrupt Link [LE0D] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.758211] ACPI: PCI Interrupt Link [LE1A] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.758424] ACPI: PCI Interrupt Link [LE1B] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.758637] ACPI: PCI Interrupt Link [LE1C] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.758849] ACPI: PCI Interrupt Link [LE1D] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.759061] ACPI: PCI Interrupt Link [LE2A] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.759274] ACPI: PCI Interrupt Link [LE2B] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.759487] ACPI: PCI Interrupt Link [LE2C] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.759699] ACPI: PCI Interrupt Link [LE2D] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.759914] ACPI: PCI Interrupt Link [LE3A] (IRQs 5 7 9 10 *11 14 15) [ 0.760144] ACPI: PCI Interrupt Link [LE3B] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.760358] ACPI: PCI Interrupt Link [LE3C] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.760573] ACPI: PCI Interrupt Link [LE3D] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.760786] ACPI: PCI Interrupt Link [LE4A] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.760999] ACPI: PCI Interrupt Link [LE4B] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.761213] ACPI: PCI Interrupt Link [LE4C] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.761426] ACPI: PCI Interrupt Link [LE4D] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.761639] ACPI: PCI Interrupt Link [LE5A] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.761852] ACPI: PCI Interrupt Link [LE5B] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.762066] ACPI: PCI Interrupt Link [LE5C] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.762279] ACPI: PCI Interrupt Link [LE5D] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.762492] ACPI: PCI Interrupt Link [LE6A] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.762706] ACPI: PCI Interrupt Link [LE6B] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.762919] ACPI: PCI Interrupt Link [LE6C] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.763132] ACPI: PCI Interrupt Link [LE6D] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.763345] ACPI: PCI Interrupt Link [LE7A] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.763558] ACPI: PCI Interrupt Link [LE7B] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.763771] ACPI: PCI Interrupt Link [LE7C] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.763984] ACPI: PCI Interrupt Link [LE7D] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.764197] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.764414] ACPI: PCI Interrupt Link [LIGP] (IRQs 5 *7 9 10 11 14 15) [ 0.764627] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15) [ 0.764841] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15) [ 0.765055] ACPI: PCI Interrupt Link [LU1B] (IRQs 5 *7 9 10 11 14 15) [ 0.765272] ACPI: PCI Interrupt Link [LU2B] (IRQs *5 7 9 10 11 14 15) [ 0.765485] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 *15) [ 0.765701] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15) [ 0.765916] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 *10 11 14 15) [ 0.766129] ACPI: PCI Interrupt Link [LSMB] (IRQs *5 7 9 10 11 14 15) [ 0.766345] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.766559] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15) [ 0.766809] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. [ 0.767054] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. [ 0.767298] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. [ 0.767542] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. [ 0.767786] ACPI: PCI Interrupt Link [AE0A] (IRQs 16) *0, disabled. [ 0.768030] ACPI: PCI Interrupt Link [AE0B] (IRQs 16) *0, disabled. [ 0.768274] ACPI: PCI Interrupt Link [AE0C] (IRQs 16) *0, disabled. [ 0.768518] ACPI: PCI Interrupt Link [AE0D] (IRQs 16) *0, disabled. [ 0.768762] ACPI: PCI Interrupt Link [AE1A] (IRQs 16) *0, disabled. [ 0.769006] ACPI: PCI Interrupt Link [AE1B] (IRQs 16) *0, disabled. [ 0.769251] ACPI: PCI Interrupt Link [AE1C] (IRQs 16) *0, disabled. [ 0.769495] ACPI: PCI Interrupt Link [AE1D] (IRQs 16) *0, disabled. [ 0.769739] ACPI: PCI Interrupt Link [AE2A] (IRQs 16) *0, disabled. [ 0.769983] ACPI: PCI Interrupt Link [AE2B] (IRQs 16) *0, disabled. [ 0.770244] ACPI: PCI Interrupt Link [AE2C] (IRQs 16) *0, disabled. [ 0.770488] ACPI: PCI Interrupt Link [AE2D] (IRQs 16) *0, disabled. [ 0.770732] ACPI: PCI Interrupt Link [AE3A] (IRQs 16) *0 [ 0.770975] ACPI: PCI Interrupt Link [AE3B] (IRQs 16) *0, disabled. [ 0.771218] ACPI: PCI Interrupt Link [AE3C] (IRQs 16) *0, disabled. [ 0.771462] ACPI: PCI Interrupt Link [AE3D] (IRQs 16) *0, disabled. [ 0.771709] ACPI: PCI Interrupt Link [AE4A] (IRQs 16) *0, disabled. [ 0.771954] ACPI: PCI Interrupt Link [AE4B] (IRQs 16) *0, disabled. [ 0.772198] ACPI: PCI Interrupt Link [AE4C] (IRQs 16) *0, disabled. [ 0.772442] ACPI: PCI Interrupt Link [AE4D] (IRQs 16) *0, disabled. [ 0.772687] ACPI: PCI Interrupt Link [AE5A] (IRQs 16) *0, disabled. [ 0.772931] ACPI: PCI Interrupt Link [AE5B] (IRQs 16) *0, disabled. [ 0.773175] ACPI: PCI Interrupt Link [AE5C] (IRQs 16) *0, disabled. [ 0.773421] ACPI: PCI Interrupt Link [AE5D] (IRQs 16) *0, disabled. [ 0.773665] ACPI: PCI Interrupt Link [AE6A] (IRQs 16) *0, disabled. [ 0.773911] ACPI: PCI Interrupt Link [AE6B] (IRQs 16) *0, disabled. [ 0.774156] ACPI: PCI Interrupt Link [AE6C] (IRQs 16) *0, disabled. [ 0.774404] ACPI: PCI Interrupt Link [AE6D] (IRQs 16) *0, disabled. [ 0.774649] ACPI: PCI Interrupt Link [AE7A] (IRQs 16) *0, disabled. [ 0.774893] ACPI: PCI Interrupt Link [AE7B] (IRQs 16) *0, disabled. [ 0.775138] ACPI: PCI Interrupt Link [AE7C] (IRQs 16) *0, disabled. [ 0.775384] ACPI: PCI Interrupt Link [AE7D] (IRQs 16) *0, disabled. [ 0.775628] ACPI: PCI Interrupt Link [AIGP] (IRQs 20 21 22 23) *0 [ 0.775873] ACPI: PCI Interrupt Link [AUBA] (IRQs 20 21 22 23) *0 [ 0.776118] ACPI: PCI Interrupt Link [AUB2] (IRQs 20 21 22 23) *0 [ 0.776362] ACPI: PCI Interrupt Link [AU1B] (IRQs 20 21 22 23) *0 [ 0.776607] ACPI: PCI Interrupt Link [AU2B] (IRQs 20 21 22 23) *0 [ 0.776852] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0 [ 0.777097] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0 [ 0.777342] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0 [ 0.777587] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0 [ 0.777832] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. [ 0.778077] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. [ 0.778323] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0 [ 0.778493] ACPI: WMI: Mapper loaded [ 0.778522] SCSI subsystem initialized [ 0.778522] libata version 3.00 loaded. [ 0.778522] usbcore: registered new interface driver usbfs [ 0.778522] usbcore: registered new interface driver hub [ 0.778522] usbcore: registered new device driver usb [ 0.778522] PCI: Using ACPI for IRQ routing [ 0.790011] Bluetooth: Core ver 2.13 [ 0.790028] NET: Registered protocol family 31 [ 0.790028] Bluetooth: HCI device and connection manager initialized [ 0.790028] Bluetooth: HCI socket layer initialized [ 0.790028] NET: Registered protocol family 8 [ 0.790030] NET: Registered protocol family 20 [ 0.790049] NetLabel: Initializing [ 0.790051] NetLabel: domain hash size = 128 [ 0.790054] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.790073] NetLabel: unlabeled traffic allowed by default [ 0.790094] hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31, 31 [ 0.790102] hpet0: 4 comparators, 64-bit 25.000000 MHz counter [ 0.800078] AppArmor: AppArmor Filesystem Enabled [ 0.810010] Switched to high resolution mode on CPU 0 [ 0.810498] Switched to high resolution mode on CPU 1 [ 0.820001] pnp: PnP ACPI init [ 0.820018] ACPI: bus type pnp registered [ 0.828145] pnp: PnP ACPI: found 11 devices [ 0.828147] ACPI: ACPI bus type pnp unregistered [ 0.828150] PnPBIOS: Disabled by ACPI PNP [ 0.828158] system 00:01: ioport range 0x1000-0x107f has been reserved [ 0.828160] system 00:01: ioport range 0x1080-0x10ff has been reserved [ 0.828162] system 00:01: ioport range 0x1400-0x147f has been reserved [ 0.828164] system 00:01: ioport range 0x1480-0x14ff has been reserved [ 0.828165] system 00:01: ioport range 0x1800-0x187f has been reserved [ 0.828167] system 00:01: ioport range 0x1880-0x18ff has been reserved [ 0.828170] system 00:01: iomem range 0xfefe1000-0xfefe10ff has been reserved [ 0.828171] system 00:01: iomem range 0x60000000-0x7fffffff has been reserved [ 0.828176] system 00:02: ioport range 0x4d0-0x4d1 has been reserved [ 0.828178] system 00:02: ioport range 0x800-0x87f has been reserved [ 0.828182] system 00:02: ioport range 0x290-0x294 has been reserved [ 0.828184] system 00:02: ioport range 0x880-0x88f has been reserved [ 0.828190] system 00:09: iomem range 0xe0000000-0xe1ffffff has been reserved [ 0.828194] system 00:0a: iomem range 0xd0000-0xd3fff has been reserved [ 0.828196] system 00:0a: iomem range 0xdaa00-0xdbfff has been reserved [ 0.828198] system 00:0a: iomem range 0xf0000-0xfbfff could not be reserved [ 0.828200] system 00:0a: iomem range 0xfc000-0xfffff could not be reserved [ 0.828202] system 00:0a: iomem range 0x9fef0000-0x9fefffff could not be reserved [ 0.828204] system 00:0a: iomem range 0xffff0000-0xffffffff has been reserved [ 0.828206] system 00:0a: iomem range 0x0-0x9ffff could not be reserved [ 0.828208] system 00:0a: iomem range 0x100000-0x9feeffff could not be reserved [ 0.828210] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved [ 0.828212] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.828214] system 00:0a: iomem range 0xfeff0000-0xfeff03ff has been reserved [ 0.862926] pci 0000:00:09.0: PCI bridge, secondary bus 0000:01 [ 0.862929] pci 0000:00:09.0: IO window: 0x9000-0x9fff [ 0.862933] pci 0000:00:09.0: MEM window: disabled [ 0.862935] pci 0000:00:09.0: PREFETCH window: disabled [ 0.862940] pci 0000:00:10.0: PCI bridge, secondary bus 0000:02 [ 0.862942] pci 0000:00:10.0: IO window: 0xa000-0xafff [ 0.862945] pci 0000:00:10.0: MEM window: 0xe2000000-0xe3ffffff [ 0.862948] pci 0000:00:10.0: PREFETCH window: 0x000000c0000000-0x000000dfffffff [ 0.862953] pci 0000:00:15.0: PCI bridge, secondary bus 0000:03 [ 0.862957] pci 0000:00:15.0: IO window: 0xb000-0xbfff [ 0.862967] pci 0000:00:15.0: MEM window: 0xe4000000-0xe5ffffff [ 0.862974] pci 0000:00:15.0: PREFETCH window: 0x000000a0000000-0x000000a00fffff [ 0.862992] pci 0000:00:09.0: setting latency timer to 64 [ 0.862998] pci 0000:00:10.0: setting latency timer to 64 [ 0.863365] ACPI: PCI Interrupt Link [AE3A] enabled at IRQ 16 [ 0.863369] pci 0000:00:15.0: PCI INT A -> Link[AE3A] -> GSI 16 (level, low) -> IRQ 16 [ 0.863377] pci 0000:00:15.0: setting latency timer to 64 [ 0.863382] bus: 00 index 0 io port: [0x00-0xffff] [ 0.863384] bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff] [ 0.863385] bus: 01 index 0 io port: [0x9000-0x9fff] [ 0.863387] bus: 01 index 1 mmio: [0x0-0x0] [ 0.863388] bus: 01 index 2 mmio: [0x0-0x0] [ 0.863390] bus: 01 index 3 io port: [0x00-0xffff] [ 0.863391] bus: 01 index 4 mmio: [0x000000-0xffffffffffffffff] [ 0.863393] bus: 02 index 0 io port: [0xa000-0xafff] [ 0.863395] bus: 02 index 1 mmio: [0xe2000000-0xe3ffffff] [ 0.863396] bus: 02 index 2 mmio: [0xc0000000-0xdfffffff] [ 0.863398] bus: 02 index 3 mmio: [0x0-0x0] [ 0.863399] bus: 03 index 0 io port: [0xb000-0xbfff] [ 0.863401] bus: 03 index 1 mmio: [0xe4000000-0xe5ffffff] [ 0.863402] bus: 03 index 2 mmio: [0xa0000000-0xa00fffff] [ 0.863404] bus: 03 index 3 mmio: [0x0-0x0] [ 0.863410] NET: Registered protocol family 2 [ 0.900084] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.900322] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.900708] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.900925] TCP: Hash tables configured (established 131072 bind 65536) [ 0.900927] TCP reno registered [ 0.910121] NET: Registered protocol family 1 [ 0.910257] checking if image is initramfs... it is [ 1.512648] Freeing initrd memory: 7676k freed [ 1.512852] cpufreq: No nForce2 chipset. [ 1.512975] audit: initializing netlink socket (disabled) [ 1.512999] type=2000 audit(1250115696.510:1): initialized [ 1.519213] highmem bounce pool size: 64 pages [ 1.519217] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.520174] VFS: Disk quotas dquot_6.5.1 [ 1.520217] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.520673] fuse init (API version 7.10) [ 1.520735] msgmni has been set to 1627 [ 1.520878] alg: No test for stdrng (krng) [ 1.520887] io scheduler noop registered [ 1.520888] io scheduler anticipatory registered [ 1.520890] io scheduler deadline registered (default) [ 1.520900] io scheduler cfq registered [ 1.561401] pci 0000:02:00.0: Boot video device [ 1.575325] pcieport-driver 0000:00:15.0: setting latency timer to 64 [ 1.575483] pcieport-driver 0000:00:15.0: found MSI capability [ 1.575572] pcieport-driver 0000:00:15.0: irq 2303 for MSI/MSI-X [ 1.575607] pci_express 0000:00:15.0:pcie00: allocate port service [ 1.575753] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.575760] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 1.575921] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 1.575923] ACPI: Power Button (FF) [PWRF] [ 1.575955] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 1.575957] ACPI: Power Button (CM) [PWRB] [ 1.576542] ACPI: SSDT 9FEFADC0, 02AE (r1 PmRef Cpu0Ist 3000 INTL 20040311) [ 1.576864] processor ACPI_CPU:00: registered as cooling_device0 [ 1.577003] ACPI: SSDT 9FEFB280, 0152 (r1 PmRef Cpu1Ist 3000 INTL 20040311) [ 1.577316] processor ACPI_CPU:01: registered as cooling_device1 [ 1.585049] isapnp: Scanning for PnP cards... [ 1.940736] isapnp: No Plug & Play device found [ 1.961537] Serial: 8250/16550 driver4 ports, IRQ sharing enabled [ 1.962310] brd: module loaded [ 1.962541] loop: module loaded [ 1.962590] Fixed MDIO Bus: probed [ 1.962595] PPP generic driver version 2.4.2 [ 1.962635] input: Macintosh mouse button emulation as /devices/virtual/input/input2 [ 1.962656] Driver 'sd' needs updating - please use bus_type methods [ 1.962662] Driver 'sr' needs updating - please use bus_type methods [ 1.962697] ahci 0000:00:0b.0: version 3.0 [ 1.963066] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23 [ 1.963072] ahci 0000:00:0b.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23 [ 1.963102] ahci 0000:00:0b.0: irq 2302 for MSI/MSI-X [ 1.963169] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 1.963172] ahci 0000:00:0b.0: flags: 64bit ncq sntf led pmp pio slum part [ 1.963174] ahci 0000:00:0b.0: setting latency timer to 64 [ 1.963550] scsi0 : ahci [ 1.963624] scsi1 : ahci [ 1.963665] scsi2 : ahci [ 1.963708] scsi3 : ahci [ 1.963750] scsi4 : ahci [ 1.963795] scsi5 : ahci [ 1.963884] ata1: SATA max UDMA/133 abar m8192@0xe6084000 port 0xe6084100 irq 2302 [ 1.963887] ata2: SATA max UDMA/133 abar m8192@0xe6084000 port 0xe6084180 irq 2302 [ 1.963888] ata3: SATA max UDMA/133 abar m8192@0xe6084000 port 0xe6084200 irq 2302 [ 1.963890] ata4: SATA max UDMA/133 abar m8192@0xe6084000 port 0xe6084280 irq 2302 [ 1.963892] ata5: SATA max UDMA/133 abar m8192@0xe6084000 port 0xe6084300 irq 2302 [ 1.963894] ata6: SATA max UDMA/133 abar m8192@0xe6084000 port 0xe6084380 irq 2302 [ 2.490034] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.490613] ata1.00: ATA-8: WDC WD10EADS-65L5B1, 01.01A01, max UDMA/133 [ 2.490617] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 2.491321] ata1.00: configured for UDMA/133 [ 2.840016] ata2: SATA link down (SStatus 0 SControl 300) [ 3.190017] ata3: SATA link down (SStatus 0 SControl 300) [ 4.120028] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 4.121932] ata4.00: ATAPI: Optiarc DVD RW AD-7240S, 1.00, max UDMA/100 [ 4.123904] ata4.00: configured for UDMA/100 [ 4.470016] ata5: SATA link down (SStatus 0 SControl 300) [ 4.820016] ata6: SATA link down (SStatus 0 SControl 300) [ 4.820147] scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-65L 01.0 PQ: 0 ANSI: 5 [ 4.820249] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [ 4.820261] sd 0:0:0:0: [sda] Write Protect is off [ 4.820263] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.820281] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.820331] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [ 4.820341] sd 0:0:0:0: [sda] Write Protect is off [ 4.820343] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.820360] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.820363] sda: sda1 < sda5 sda6 > sda3 [ 4.844033] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.844073] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 4.845259] scsi 3:0:0:0: CD-ROM Optiarc DVD RW AD-7240S 1.00 PQ: 0 ANSI: 5 [ 4.849510] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 4.849514] Uniform CD-ROM driver Revision: 3.20 [ 4.849638] sr 3:0:0:0: Attached scsi CD-ROM sr0 [ 4.849690] sr 3:0:0:0: Attached scsi generic sg1 type 5 [ 4.849782] sata_sil24 0000:03:00.0: version 1.1 [ 4.849795] sata_sil24 0000:03:00.0: PCI INT A -> Link[AE3A] -> GSI 16 (level, low) -> IRQ 16 [ 4.849862] sata_sil24 0000:03:00.0: setting latency timer to 64 [ 4.850037] scsi6 : sata_sil24 [ 4.850079] scsi7 : sata_sil24 [ 4.850107] ata7: SATA max UDMA/100 host m128@0xe5004000 port 0xe5000000 irq 16 [ 4.850110] ata8: SATA max UDMA/100 host m128@0xe5004000 port 0xe5002000 irq 16 [ 7.070033] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 7.070267] ata7.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9 [ 7.070529] ata7.00: hard resetting link [ 7.420306] ata7.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 7.420310] ata7.01: hard resetting link [ 7.770306] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 7.770310] ata7.02: hard resetting link [ 8.120317] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 8.120321] ata7.03: hard resetting link [ 8.470302] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 8.470306] ata7.04: hard resetting link [ 8.820307] ata7.04: SATA link down (SStatus 0 SControl 320) [ 8.820311] ata7.05: hard resetting link [ 9.170231] ata7.05: failed to read SCR 1 (Emask=0x1) [ 9.170233] ata7.05: failed to read SCR 0 (Emask=0x40) [ 9.170236] ata7.00: failed to IDENTIFY (I/O error, err_mask=0x40) [ 9.170239] ata7.15: hard resetting link [ 11.390033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 12.420064] ata7.00: hard resetting link [ 12.770304] ata7.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 12.770308] ata7.01: hard resetting link [ 13.120305] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 13.120309] ata7.02: hard resetting link [ 13.470305] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 13.470310] ata7.03: hard resetting link [ 13.820304] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 14.170032] ata7.05: hard resetting link [ 14.520232] ata7.05: failed to read SCR 1 (Emask=0x1) [ 14.520234] ata7.05: failed to read SCR 0 (Emask=0x40) [ 14.520236] ata7.00: failed to IDENTIFY (I/O error, err_mask=0x40) [ 14.520238] ata7.15: hard resetting link [ 16.740033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 17.770045] ata7.00: hard resetting link [ 18.120307] ata7.00: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 18.120311] ata7.01: hard resetting link [ 18.470306] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 18.470310] ata7.02: hard resetting link [ 18.820305] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 18.820309] ata7.03: hard resetting link [ 19.170306] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 19.170310] ata7.04: hard resetting link [ 19.520304] ata7.04: SATA link down (SStatus 0 SControl 320) [ 19.520308] ata7.05: hard resetting link [ 19.870231] ata7.05: failed to read SCR 1 (Emask=0x1) [ 19.870233] ata7.05: failed to read SCR 0 (Emask=0x40) [ 19.870235] ata7.00: failed to IDENTIFY (I/O error, err_mask=0x40) [ 19.870237] ata7.00: failed to recover link after 3 tries, disabling [ 19.870239] ata7.15: hard resetting link [ 22.090033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 23.470070] ata7.01: hard resetting link [ 23.820305] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 23.820310] ata7.02: hard resetting link [ 24.170304] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 24.170309] ata7.03: hard resetting link [ 24.520305] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 24.870054] ata7.05: hard resetting link [ 25.220231] ata7.05: failed to read SCR 1 (Emask=0x1) [ 25.220233] ata7.05: failed to read SCR 0 (Emask=0x40) [ 25.220236] ata7.01: failed to IDENTIFY (I/O error, err_mask=0x40) [ 25.220238] ata7.15: hard resetting link [ 27.440033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 28.820051] ata7.01: hard resetting link [ 29.170317] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 29.170322] ata7.02: hard resetting link [ 29.520305] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 29.520309] ata7.03: hard resetting link [ 29.870317] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 29.870321] ata7.04: hard resetting link [ 30.220304] ata7.04: SATA link down (SStatus 0 SControl 320) [ 30.220309] ata7.05: hard resetting link [ 30.570232] ata7.05: failed to read SCR 1 (Emask=0x1) [ 30.570234] ata7.05: failed to read SCR 0 (Emask=0x40) [ 30.570236] ata7.01: failed to IDENTIFY (I/O error, err_mask=0x40) [ 30.570238] ata7.15: hard resetting link [ 32.790033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 34.170032] ata7.01: hard resetting link [ 34.520306] ata7.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 34.520310] ata7.02: hard resetting link [ 34.870306] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 34.870311] ata7.03: hard resetting link [ 35.220319] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 35.570019] ata7.05: hard resetting link [ 35.920232] ata7.05: failed to read SCR 1 (Emask=0x1) [ 35.920234] ata7.05: failed to read SCR 0 (Emask=0x40) [ 35.920236] ata7.01: failed to IDENTIFY (I/O error, err_mask=0x40) [ 35.920238] ata7.01: failed to recover link after 3 tries, disabling [ 35.920240] ata7.15: hard resetting link [ 38.140033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 39.870057] ata7.02: hard resetting link [ 40.220305] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 40.220309] ata7.03: hard resetting link [ 40.570307] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 40.570311] ata7.04: hard resetting link [ 40.920306] ata7.04: SATA link down (SStatus 0 SControl 320) [ 40.920310] ata7.05: hard resetting link [ 41.270232] ata7.05: failed to read SCR 1 (Emask=0x1) [ 41.270234] ata7.05: failed to read SCR 0 (Emask=0x40) [ 41.270236] ata7.02: failed to IDENTIFY (I/O error, err_mask=0x40) [ 41.270238] ata7.15: hard resetting link [ 43.490033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 45.220038] ata7.02: hard resetting link [ 45.570319] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 45.570323] ata7.03: hard resetting link [ 45.920306] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 46.270044] ata7.05: hard resetting link [ 46.620231] ata7.05: failed to read SCR 1 (Emask=0x1) [ 46.620233] ata7.05: failed to read SCR 0 (Emask=0x40) [ 46.620236] ata7.02: failed to IDENTIFY (I/O error, err_mask=0x40) [ 46.620238] ata7.15: hard resetting link [ 48.840033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 50.570020] ata7.02: hard resetting link [ 50.920307] ata7.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 50.920311] ata7.03: hard resetting link [ 51.270304] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 51.270308] ata7.04: hard resetting link [ 51.620305] ata7.04: SATA link down (SStatus 0 SControl 320) [ 51.620309] ata7.05: hard resetting link [ 51.970231] ata7.05: failed to read SCR 1 (Emask=0x1) [ 51.970233] ata7.05: failed to read SCR 0 (Emask=0x40) [ 51.970235] ata7.02: failed to IDENTIFY (I/O error, err_mask=0x40) [ 51.970237] ata7.02: failed to recover link after 3 tries, disabling [ 51.970239] ata7.15: hard resetting link [ 54.190033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 56.270044] ata7.03: hard resetting link [ 56.620304] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 56.970054] ata7.05: hard resetting link [ 57.320231] ata7.05: failed to read SCR 1 (Emask=0x1) [ 57.320233] ata7.05: failed to read SCR 0 (Emask=0x40) [ 57.320236] ata7.03: failed to IDENTIFY (I/O error, err_mask=0x40) [ 57.320238] ata7.15: hard resetting link [ 59.540033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 61.620026] ata7.03: hard resetting link [ 61.970305] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 61.970309] ata7.04: hard resetting link [ 62.320304] ata7.04: SATA link down (SStatus 0 SControl 320) [ 62.320308] ata7.05: hard resetting link [ 62.670231] ata7.05: failed to read SCR 1 (Emask=0x1) [ 62.670233] ata7.05: failed to read SCR 0 (Emask=0x40) [ 62.670236] ata7.03: failed to IDENTIFY (I/O error, err_mask=0x40) [ 62.670238] ata7.15: hard resetting link [ 64.890033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 66.970070] ata7.03: hard resetting link [ 67.320303] ata7.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 67.670032] ata7.05: hard resetting link [ 68.020232] ata7.05: failed to read SCR 1 (Emask=0x1) [ 68.020234] ata7.05: failed to read SCR 0 (Emask=0x40) [ 68.020237] ata7.03: failed to IDENTIFY (I/O error, err_mask=0x40) [ 68.020238] ata7.03: failed to recover link after 3 tries, disabling [ 68.020240] ata7.15: hard resetting link [ 70.240033] ata7.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 71.640152] ata7.04: hard resetting link [ 71.990295] ata7.04: SATA link down (SStatus 0 SControl 320) [ 73.020013] ata7.05: hard resetting link [ 73.370232] ata7.05: failed to read SCR 1 (Emask=0x1) [ 73.370234] ata7.05: failed to read SCR 0 (Emask=0x40) [ 73.370237] ata7.15: failed to write PMP_FEAT_EN (Emask=0x40) [ 73.370286] ata7: failed to recover PMP after 5 tries, giving up [ 73.370332] ata7.15: Port Multiplier detaching [ 73.370356] ata7.00: disabled [ 73.370363] ata7: exception Emask 0x3 SAct 0x0 SErr 0x0 action 0x6 frozen t4 [ 73.370410] ata7: irq_stat 0x00060002, device error via D2H FIS [ 73.370458] ata7: hard resetting link [ 75.590033] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 0) [ 75.590039] ata7: EH complete [ 77.680036] ata8: SATA link down (SStatus 0 SControl 0) [ 77.680582] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 77.680984] ACPI: PCI Interrupt Link [AUB2] enabled at IRQ 22 [ 77.680989] ehci_hcd 0000:00:04.1: PCI INT B -> Link[AUB2] -> GSI 22 (level, low) -> IRQ 22 [ 77.680998] ehci_hcd 0000:00:04.1: setting latency timer to 64 [ 77.681001] ehci_hcd 0000:00:04.1: EHCI Host Controller [ 77.681055] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1 [ 77.681078] ehci_hcd 0000:00:04.1: debug port 1 [ 77.681082] ehci_hcd 0000:00:04.1: cache line size of 32 is not supported [ 77.681093] ehci_hcd 0000:00:04.1: irq 22, io mem 0xe6089000 [ 77.700018] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00 [ 77.700109] usb usb1: configuration #1 chosen from 1 choice [ 77.700152] hub 1-0:1.0: USB hub found [ 77.700162] hub 1-0:1.0: 6 ports detected [ 77.700472] ACPI: PCI Interrupt Link [AU2B] disabled and referenced, BIOS bug [ 77.700615] ACPI: PCI Interrupt Link [AU2B] enabled at IRQ 21 [ 77.700619] ehci_hcd 0000:00:06.1: PCI INT B -> Link[AU2B] -> GSI 21 (level, low) -> IRQ 21 [ 77.700626] ehci_hcd 0000:00:06.1: setting latency timer to 64 [ 77.700629] ehci_hcd 0000:00:06.1: EHCI Host Controller [ 77.700660] ehci_hcd 0000:00:06.1: new USB bus registered, assigned bus number 2 [ 77.700681] ehci_hcd 0000:00:06.1: debug port 1 [ 77.700685] ehci_hcd 0000:00:06.1: cache line size of 32 is not supported [ 77.700695] ehci_hcd 0000:00:06.1: irq 21, io mem 0xe608b000 [ 77.720016] ehci_hcd 0000:00:06.1: USB 2.0 started, EHCI 1.00 [ 77.720104] usb usb2: configuration #1 chosen from 1 choice [ 77.720141] hub 2-0:1.0: USB hub found [ 77.720150] hub 2-0:1.0: 6 ports detected [ 77.720246] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 77.720613] ACPI: PCI Interrupt Link [AUBA] enabled at IRQ 20 [ 77.720616] ohci_hcd 0000:00:04.0: PCI INT A -> Link[AUBA] -> GSI 20 (level, low) -> IRQ 20 [ 77.720624] ohci_hcd 0000:00:04.0: setting latency timer to 64 [ 77.720626] ohci_hcd 0000:00:04.0: OHCI Host Controller [ 77.720662] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 3 [ 77.720678] ohci_hcd 0000:00:04.0: irq 20, io mem 0xe608c000 [ 77.782060] usb usb3: configuration #1 chosen from 1 choice [ 77.782078] hub 3-0:1.0: USB hub found [ 77.782084] hub 3-0:1.0: 6 ports detected [ 77.782500] ACPI: PCI Interrupt Link [AU1B] enabled at IRQ 23 [ 77.782503] ohci_hcd 0000:00:06.0: PCI INT A -> Link[AU1B] -> GSI 23 (level, low) -> IRQ 23 [ 77.782510] ohci_hcd 0000:00:06.0: setting latency timer to 64 [ 77.782512] ohci_hcd 0000:00:06.0: OHCI Host Controller [ 77.782543] ohci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 4 [ 77.782564] ohci_hcd 0000:00:06.0: irq 23, io mem 0xe608a000 [ 77.842053] usb usb4: configuration #1 chosen from 1 choice [ 77.842071] hub 4-0:1.0: USB hub found [ 77.842077] hub 4-0:1.0: 6 ports detected [ 77.842140] uhci_hcd: USB Universal Host Controller Interface driver [ 77.842210] PNP: No PS/2 controller found. Probing ports directly. [ 77.842601] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 77.842608] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 77.850058] mice: PS/2 mouse device common for all mice [ 77.880124] rtc_cmos 00:05: RTC can wake from S4 [ 77.880174] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 [ 77.880229] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs [ 77.880273] device-mapper: uevent: version 1.0.3 [ 77.880337] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@xxxxxxxxxx [ 77.880388] device-mapper: multipath: version 1.0.5 loaded [ 77.880390] device-mapper: multipath round-robin: version 1.0.0 loaded [ 77.880449] EISA: Probing bus 0 at eisa.0 [ 77.880455] Cannot allocate resource for EISA slot 1 [ 77.880474] EISA: Detected 0 cards. [ 77.880514] cpuidle: using governor ladder [ 77.880515] cpuidle: using governor menu [ 77.880898] TCP cubic registered [ 77.880991] NET: Registered protocol family 10 [ 77.881325] lo: Disabled Privacy Extensions [ 77.881569] NET: Registered protocol family 17 [ 77.881581] Bluetooth: L2CAP ver 2.11 [ 77.881583] Bluetooth: L2CAP socket layer initialized [ 77.881585] Bluetooth: SCO (Voice Link) ver 0.6 [ 77.881586] Bluetooth: SCO socket layer initialized [ 77.881607] Bluetooth: RFCOMM socket layer initialized [ 77.881614] Bluetooth: RFCOMM TTY layer initialized [ 77.881615] Bluetooth: RFCOMM ver 1.10 [ 77.883090] Using IPI No-Shortcut mode [ 77.883147] registered taskstats version 1 [ 77.883247] Magic number: 5:72:401 [ 77.883356] rtc_cmos 00:05: setting system clock to 2009-08-12 22:22:53 UTC (1250115773) [ 77.883358] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 77.883359] EDD information not available. [ 77.883631] Freeing unused kernel memory: 544k freed [ 77.883723] Write protecting the kernel text: 4172k [ 77.883788] Write protecting the kernel read-only data: 1544k [ 78.001778] md: linear personality registered for level -1 [ 78.003424] md: multipath personality registered for level -4 [ 78.004913] md: raid0 personality registered for level 0 [ 78.007237] md: raid1 personality registered for level 1 [ 78.008611] xor: automatically using best checksumming function: pIII_sse [ 78.051254] pIII_sse : 9412.800 MB/sec [ 78.051255] xor: using function: pIII_sse (9412.800 MB/sec) [ 78.051549] async_tx: api initialized (sync-only) [ 78.221273] raid6: int32x1 913 MB/s [ 78.290009] usb 4-2: new low speed USB device using ohci_hcd and address 2 [ 78.391257] raid6: int32x2 969 MB/s [ 78.561277] raid6: int32x4 739 MB/s [ 78.566165] usb 4-2: configuration #1 chosen from 1 choice [ 78.731338] raid6: int32x8 691 MB/s [ 78.901273] raid6: mmxx1 3113 MB/s [ 78.910011] usb 4-5: new low speed USB device using ohci_hcd and address 3 [ 79.071264] raid6: mmxx2 3555 MB/s [ 79.128254] usb 4-5: configuration #1 chosen from 1 choice [ 79.241264] raid6: sse1x1 2099 MB/s [ 79.411270] raid6: sse1x2 2685 MB/s [ 79.581268] raid6: sse2x1 3805 MB/s [ 79.751266] raid6: sse2x2 4033 MB/s [ 79.751268] raid6: using algorithm sse2x2 (4033 MB/s) [ 79.751271] md: raid6 personality registered for level 6 [ 79.751273] md: raid5 personality registered for level 5 [ 79.751275] md: raid4 personality registered for level 4 [ 79.756505] md: raid10 personality registered for level 10 [ 79.808936] Floppy drive(s): fd0 is 1.44M [ 79.825153] FDC 0 is a post-1991 82077 [ 79.831276] usbcore: registered new interface driver hiddev [ 79.839531] input: HOLTEK Wireless 2.4GHz TouchPad Keyboard as /devices/pci0000:00/0000:00:06.0/usb4/4-2/4-2:1.0/input/input3 [ 79.841520] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61. [ 79.841951] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22 [ 79.841955] forcedeth 0000:00:0a.0: PCI INT A -> Link[APCH] -> GSI 22 (level, low) -> IRQ 22 [ 79.841960] forcedeth 0000:00:0a.0: setting latency timer to 64 [ 79.871687] generic-usb 0003:1241:F767.0001: input,hidraw0: USB HID v1.10 Keyboard [HOLTEK Wireless 2.4GHz TouchPad Keyboard] on usb-0000:00:06.0-2/input0 [ 79.883687] input: HOLTEK Wireless 2.4GHz TouchPad Keyboard as /devices/pci0000:00/0000:00:06.0/usb4/4-2/4-2:1.1/input/input4 [ 79.931277] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:1d:1c:3d:0f [ 79.931281] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt timirq gbit lnktim msi desc-v3 [ 79.941516] generic-usb 0003:1241:F767.0002: input,hiddev96,hidraw1: USB HID v1.10 Mouse [HOLTEK Wireless 2.4GHz TouchPad Keyboard] on usb-0000:00:06.0-2/input1 [ 79.941571] usbcore: registered new interface driver usbhid [ 79.941574] usbhid: v2.6:USB HID core driver [ 80.752011] PM: Starting manual resume from disk [ 80.752014] PM: Resume from partition 8:6 [ 80.752015] PM: Checking hibernation image. [ 80.752112] PM: Resume from disk failed. [ 80.796853] kjournald starting. Commit interval 5 seconds [ 80.796868] EXT3-fs: mounted filesystem with ordered data mode. [ 82.064366] udev: starting version 141 [ 82.549602] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 82.555437] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 82.581333] Linux agpgart interface v0.103 [ 83.729463] nvidia: module license 'NVIDIA' taints kernel. [ 83.775492] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 21 [ 83.775497] HDA Intel 0000:00:08.0: PCI INT A -> Link[AAZA] -> GSI 21 (level, low) -> IRQ 21 [ 83.775712] HDA Intel 0000:00:08.0: setting latency timer to 64 [ 83.794845] lirc_dev: IR Remote Control driver registered, major 61 [ 83.799809] Driver for Soundgraph iMON MultiMedia IR/Display, v0.5 [ 83.799811] Venky Raju <dev@xxxxxxxx> [ 83.799829] imon_probe: found iMON device [ 83.799833] lirc_dev: lirc_register_driver: sample_rate: 0 [ 83.799873] imon_probe: Registered iMON driver(minor:0) [ 83.799891] imon_probe: iMON device on usb<4:3> initialized [ 83.799897] imon_probe: found iMON device [ 83.799899] lirc_dev: lirc_register_driver: sample_rate: 0 [ 83.799915] imon_probe: Registered iMON driver(minor:1) [ 83.799931] imon_probe: iMON device on usb<4:3> initialized [ 83.799942] usbcore: registered new interface driver lirc_imon [ 83.984682] ACPI: PCI Interrupt Link [AIGP] enabled at IRQ 20 [ 83.984687] nvidia 0000:02:00.0: PCI INT A -> Link[AIGP] -> GSI 20 (level, low) -> IRQ 20 [ 83.984695] nvidia 0000:02:00.0: setting latency timer to 64 [ 83.984888] NVRM: loading NVIDIA UNIX x86 Kernel Module 185.18.29 Thu Jul 23 05:09:54 PDT 2009 [ 84.751264] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS... [ 86.590814] lp: driver loaded but no devices found [ 86.831856] Adding 915664k swap on /dev/sda6. Priority:-1 extents:1 across:915664k [ 87.425472] EXT3 FS on sda5, internal journal [ 88.232547] kjournald starting. Commit interval 5 seconds [ 88.232997] EXT3 FS on sda3, internal journal [ 88.233004] EXT3-fs: mounted filesystem with ordered data mode. [ 88.598909] type=1505 audit(1250115784.206:2): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2161 [ 88.599000] type=1505 audit(1250115784.206:3): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2161 [ 88.599033] type=1505 audit(1250115784.206:4): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2161 [ 88.599069] type=1505 audit(1250115784.206:5): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2161 [ 88.643522] type=1505 audit(1250115784.256:6): operation="profile_load" name="/usr/sbin/mysqld" name2="default" pid=2166 [ 88.671703] type=1505 audit(1250115784.286:7): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2170 [ 89.383333] forcedeth 0000:00:0a.0: irq 2301 for MSI/MSI-X [ 99.951260] eth0: no IPv6 routers present [ 104.995626] IR port opened [ 105.141853] display port opened