Woops, I forgot the attachments. Attached now :) On Fri, Jun 19, 2009 at 11:38 AM, Marc Bowes<marcbowes@xxxxxxxxx> wrote: > Hi, > > Tejun, the motherboard is a Gigabyte EP45-DQ6. Attached are dmidecode > and a new dmesg.txt, as I have enabled AHCI mode. > > Robert, > 0a:00.0 SATA controller: JMicron Technologies, Inc. JMicron > 20360/20363 AHCI Controller (rev 02) > 0a:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 > AHCI Controller (rev 02) > Those are the two JMicron controllers I have. I assume you mean the > SATA one. The AHCI controller is: > 00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA > AHCI Controller > I'm not sure if just that controller will be sufficient? Anyways, I > will experiment. > > Thanks > > On Fri, Jun 19, 2009 at 6:00 AM, Tejun Heo<htejun@xxxxxxxxx> wrote: >> Robert Hancock wrote: >>> On 06/16/2009 09:21 AM, James Bottomley wrote: >>>> On Tue, 2009-06-16 at 17:03 +0200, Marc Bowes wrote: >>>>> Sorry to bother, but this is really bugging me! I can't seem to find >>>>> anybody >>>>> else with the same problem. What steps should I be taking to figure this >>>>> out? I'm thinking I should be trying other kernel versions and/or >>>>> plugging >>>>> drives in different places. I don't think the motherboard is faulty, >>>>> and I >>>>> seem to be getting good speeds (~70mbs) to all four drives. >>>> >>>> Well, those are on the AHCI built in controller. The one with the slow >>>> response is the empty JMicron 20360/20363. But why this should be so, >>>> I've no idea ... it looks like the AHCI driver can't tell the phys are >>>> empty for some reason, which could be due to many things. >>> >>> I would suspect it's a hardware problem that we can't do much about.. >>> For some reason the controller is reporting the SATA link is online at >>> 3Gbps when there's actually nothing connected. We try to repeatedly >>> reset the "device" as it doesn't respond properly, until we finally give >>> up. >>> >>> Can you disable that JMicron controller in the BIOS somehow? >> >> It could be some storage controller hanging off there. Some revisions >> of SIMG PMPs operating in raid mode keep the link online while failing >> to respond to reset if the downstream ports are empty. Marc, which >> motherboard are you using? Can you please post the output of >> dmidecode? >> >> Thanks. >> >> -- >> tejun >> >
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.29-gentoo-r5 (root@saidin) (gcc version 4.3.2 (Gentoo 4.3.2-r3 p1.6, pie-10.1.5) ) #9 SMP Thu Jun 11 03:45:24 SAST 2009 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cfeb0000 (usable) [ 0.000000] BIOS-e820: 00000000cfeb0000 - 00000000cfee3000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000cfee3000 - 00000000cfef0000 (ACPI data) [ 0.000000] BIOS-e820: 00000000cfef0000 - 00000000cff00000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000e4000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable) [ 0.000000] DMI 2.4 present. [ 0.000000] last_pfn = 0xcfeb0 max_arch_pfn = 0x100000 [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] kernel direct mapping tables up to 373fe000 @ 7000-d000 [ 0.000000] ACPI: RSDP 000F7910, 0014 (r0 GBT ) [ 0.000000] ACPI: RSDT CFEE3040, 0034 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) [ 0.000000] ACPI: FACP CFEE30C0, 0074 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) [ 0.000000] FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) [ 0.000000] ACPI: DSDT CFEE3180, 4C52 (r1 GBT GBTUACPI 1000 MSFT 100000C) [ 0.000000] ACPI: FACS CFEB0000, 0040 [ 0.000000] ACPI: MCFG CFEE7FC0, 003C (r1 GBT GBTUACPI 42302E31 GBTU 1010101) [ 0.000000] ACPI: APIC CFEE7E40, 0084 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) [ 0.000000] ACPI: SSDT CFEE89A0, 03AB (r1 PmRef CpuPm 3000 INTL 20040311) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] 2442MB HIGHMEM available. [ 0.000000] 883MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 373fe000 [ 0.000000] low ram: 00000000 - 373fe000 [ 0.000000] bootmap 00008000 - 0000ee80 [ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 00373fe000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] [ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] [ 0.000000] #3 [0001000000 - 000168a574] TEXT DATA BSS ==> [0001000000 - 000168a574] [ 0.000000] #4 [000168b000 - 0001692000] INIT_PG_TABLE ==> [000168b000 - 0001692000] [ 0.000000] #5 [000009e800 - 0000100000] BIOS reserved ==> [000009e800 - 0000100000] [ 0.000000] #6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000] [ 0.000000] #7 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000] [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00001000 [ 0.000000] Normal 0x00001000 -> 0x000373fe [ 0.000000] HighMem 0x000373fe -> 0x000cfeb0 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x0000009e [ 0.000000] 0: 0x00000100 -> 0x000cfeb0 [ 0.000000] On node 0 totalpages: 851534 [ 0.000000] free_area_init_node: node 0, pgdat c1553380, node_mem_map c1692000 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3966 pages, LIFO batch:0 [ 0.000000] Normal zone: 1736 pages used for memmap [ 0.000000] Normal zone: 220470 pages, LIFO batch:31 [ 0.000000] HighMem zone: 4886 pages used for memmap [ 0.000000] HighMem zone: 620444 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 24 [ 0.000000] Allocating PCI resources starting at e6000000 (gap: e4000000:1ac00000) [ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] PERCPU: Allocating 40960 bytes of per cpu data [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 844880 [ 0.000000] Kernel command line: root=/dev/sda3 video=uvesafb:mtrr:3,ywrap,1680x1050-32@60 [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 2399.890 MHz processor. [ 0.000999] Console: colour VGA+ 80x25 [ 0.000999] console [tty0] enabled [ 0.000999] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000999] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000999] Memory: 3370812k/3406528k available (3786k kernel code, 34464k reserved, 2028k data, 324k init, 2501320k highmem) [ 0.000999] virtual kernel memory layout: [ 0.000999] fixmap : 0xffc79000 - 0xfffff000 (3608 kB) [ 0.000999] pkmap : 0xff400000 - 0xff800000 (4096 kB) [ 0.000999] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB) [ 0.000999] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB) [ 0.000999] .init : 0xc15b4000 - 0xc1605000 ( 324 kB) [ 0.000999] .data : 0xc13b2833 - 0xc15adb80 (2028 kB) [ 0.000999] .text : 0xc1000000 - 0xc13b2833 (3786 kB) [ 0.000999] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000999] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.001006] Calibrating delay loop (skipped), value calculated using timer frequency.. 4799.78 BogoMIPS (lpj=2399890) [ 0.001293] Security Framework initialized [ 0.001432] Mount-cache hash table entries: 512 [ 0.001665] Initializing cgroup subsys ns [ 0.001799] Initializing cgroup subsys cpuacct [ 0.001944] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.002122] CPU: L2 cache: 4096K [ 0.002251] CPU: Physical Processor ID: 0 [ 0.002383] CPU: Processor Core ID: 0 [ 0.002514] using mwait in idle threads. [ 0.002651] Checking 'hlt' instruction... OK. [ 0.006595] ACPI: Core revision 20081204 [ 0.013408] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.024187] CPU0: Intel(R) Core(TM)2 Quad CPU @ 2.40GHz stepping 07 [ 0.024996] Booting processor 1 APIC 0x3 ip 0x6000 [ 0.000999] Initializing CPU#1 [ 0.000999] Calibrating delay using timer specific routine.. 4799.31 BogoMIPS (lpj=2399656) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.000999] CPU: L2 cache: 4096K [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 3 [ 0.000999] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 [ 0.096347] CPU1: Intel(R) Core(TM)2 Quad CPU @ 2.40GHz stepping 07 [ 0.097159] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 0.098130] Booting processor 2 APIC 0x1 ip 0x6000 [ 0.000999] Initializing CPU#2 [ 0.000999] Calibrating delay using timer specific routine.. 4799.32 BogoMIPS (lpj=2399664) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.000999] CPU: L2 cache: 4096K [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 1 [ 0.000999] x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106 [ 0.171395] CPU2: Intel(R) Core(TM)2 Quad CPU @ 2.40GHz stepping 07 [ 0.172163] checking TSC synchronization [CPU#0 -> CPU#2]: passed. [ 0.174026] Booting processor 3 APIC 0x2 ip 0x6000 [ 0.000999] Initializing CPU#3 [ 0.000999] Calibrating delay using timer specific routine.. 4799.28 BogoMIPS (lpj=2399644) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.000999] CPU: L2 cache: 4096K [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 2 [ 0.000999] x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106 [ 0.246409] CPU3: Intel(R) Core(TM)2 Quad CPU @ 2.40GHz stepping 07 [ 0.247139] checking TSC synchronization [CPU#0 -> CPU#3]: passed. [ 0.248028] Brought up 4 CPUs [ 0.248964] Total of 4 processors activated (19197.70 BogoMIPS). [ 0.249177] khelper used greatest stack depth: 7128 bytes left [ 0.249177] net_namespace: 556 bytes [ 0.250112] NET: Registered protocol family 16 [ 0.250270] ACPI: bus type pci registered [ 0.251008] dca service started, version 1.8 [ 0.251119] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63 [ 0.251135] PCI: MCFG area at e0000000 reserved in E820 [ 0.251302] PCI: Using MMCONFIG for extended config space [ 0.251439] PCI: Using configuration type 1 for base access [ 0.257992] bio: create slab <bio-0> at 0 [ 0.259448] ACPI: EC: Look up EC in DSDT [ 0.265026] ACPI: Interpreter enabled [ 0.265177] ACPI: (supports S0 S3 S5) [ 0.265424] ACPI: Using IOAPIC for interrupt routing [ 0.271100] ACPI: No dock devices found. [ 0.271249] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.271979] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 0.272122] pci 0000:00:01.0: PME# disabled [ 0.272308] pci 0000:00:1a.0: reg 20 io port: [0xe100-0xe11f] [ 0.272371] pci 0000:00:1a.1: reg 20 io port: [0xe200-0xe21f] [ 0.272434] pci 0000:00:1a.2: reg 20 io port: [0xe000-0xe01f] [ 0.272487] pci 0000:00:1a.7: reg 10 32bit mmio: [0xec605000-0xec6053ff] [ 0.272562] pci 0000:00:1b.0: reg 10 64bit mmio: [0xec600000-0xec603fff] [ 0.272607] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 0.272768] pci 0000:00:1b.0: PME# disabled [ 0.272972] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.273114] pci 0000:00:1c.0: PME# disabled [ 0.273301] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 0.273961] pci 0000:00:1c.4: PME# disabled [ 0.274133] pci 0000:00:1d.0: reg 20 io port: [0xe300-0xe31f] [ 0.274196] pci 0000:00:1d.1: reg 20 io port: [0xe400-0xe41f] [ 0.274258] pci 0000:00:1d.2: reg 20 io port: [0xe500-0xe51f] [ 0.274311] pci 0000:00:1d.7: reg 10 32bit mmio: [0xec604000-0xec6043ff] [ 0.274467] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO [ 0.274718] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO [ 0.274960] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 000f) [ 0.275191] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 000f) [ 0.275422] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 4700 (mask 000b) [ 0.275691] pci 0000:00:1f.2: reg 10 io port: [0xe600-0xe607] [ 0.275696] pci 0000:00:1f.2: reg 14 io port: [0xe700-0xe703] [ 0.275701] pci 0000:00:1f.2: reg 18 io port: [0xe800-0xe807] [ 0.275706] pci 0000:00:1f.2: reg 1c io port: [0xe900-0xe903] [ 0.275711] pci 0000:00:1f.2: reg 20 io port: [0xea00-0xea1f] [ 0.275716] pci 0000:00:1f.2: reg 24 32bit mmio: [0xec606000-0xec6067ff] [ 0.275782] pci 0000:00:1f.2: PME# supported from D3hot [ 0.275960] pci 0000:00:1f.2: PME# disabled [ 0.276114] pci 0000:00:1f.3: reg 10 64bit mmio: [0xec607000-0xec6070ff] [ 0.276127] pci 0000:00:1f.3: reg 20 io port: [0x500-0x51f] [ 0.276163] pci 0000:01:00.0: reg 10 32bit mmio: [0xe6000000-0xe6ffffff] [ 0.276171] pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff] [ 0.276179] pci 0000:01:00.0: reg 1c 64bit mmio: [0xe4000000-0xe5ffffff] [ 0.276183] pci 0000:01:00.0: reg 24 io port: [0x8000-0x807f] [ 0.276188] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff] [ 0.276225] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.276518] pci 0000:00:01.0: bridge io port: [0x8000-0x8fff] [ 0.276521] pci 0000:00:01.0: bridge 32bit mmio: [0xe4000000-0xe7ffffff] [ 0.276525] pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff] [ 0.276594] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 0.276737] pci 0000:02:00.0: PME# disabled [ 0.279038] pci 0000:00:1c.0: bridge io port: [0x9000-0xcfff] [ 0.279043] pci 0000:00:1c.0: bridge 32bit mmio: [0xe8000000-0xebffffff] [ 0.279050] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xec000000-0xec3fffff] [ 0.279150] pci 0000:03:01.0: PME# supported from D0 D3hot D3cold [ 0.279304] pci 0000:03:01.0: PME# disabled [ 0.279513] pci 0000:03:02.0: PME# supported from D0 D3hot D3cold [ 0.279657] pci 0000:03:02.0: PME# disabled [ 0.279865] pci 0000:03:03.0: PME# supported from D0 D3hot D3cold [ 0.279961] pci 0000:03:03.0: PME# disabled [ 0.280187] pci 0000:03:04.0: PME# supported from D0 D3hot D3cold [ 0.280331] pci 0000:03:04.0: PME# disabled [ 0.280540] pci 0000:03:05.0: PME# supported from D0 D3hot D3cold [ 0.280684] pci 0000:03:05.0: PME# disabled [ 0.280892] pci 0000:03:06.0: PME# supported from D0 D3hot D3cold [ 0.280961] pci 0000:03:06.0: PME# disabled [ 0.281162] pci 0000:02:00.0: bridge io port: [0x9000-0xcfff] [ 0.281168] pci 0000:02:00.0: bridge 32bit mmio: [0xe8000000-0xebffffff] [ 0.281176] pci 0000:02:00.0: bridge 64bit mmio pref: [0xec000000-0xec3fffff] [ 0.281277] pci 0000:05:00.0: reg 10 io port: [0x9000-0x90ff] [ 0.281301] pci 0000:05:00.0: reg 18 64bit mmio: [0xec010000-0xec010fff] [ 0.281317] pci 0000:05:00.0: reg 20 64bit mmio: [0xec000000-0xec00ffff] [ 0.281326] pci 0000:05:00.0: reg 30 32bit mmio: [0x000000-0x00ffff] [ 0.281388] pci 0000:05:00.0: supports D1 D2 [ 0.281390] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.281536] pci 0000:05:00.0: PME# disabled [ 0.283086] pci 0000:03:02.0: bridge io port: [0x9000-0x9fff] [ 0.283092] pci 0000:03:02.0: bridge 32bit mmio: [0xe8000000-0xe8ffffff] [ 0.283102] pci 0000:03:02.0: bridge 64bit mmio pref: [0xec000000-0xec0fffff] [ 0.283174] pci 0000:06:00.0: reg 10 io port: [0xa000-0xa0ff] [ 0.283198] pci 0000:06:00.0: reg 18 64bit mmio: [0xec110000-0xec110fff] [ 0.283214] pci 0000:06:00.0: reg 20 64bit mmio: [0xec100000-0xec10ffff] [ 0.283223] pci 0000:06:00.0: reg 30 32bit mmio: [0x000000-0x00ffff] [ 0.283285] pci 0000:06:00.0: supports D1 D2 [ 0.283286] pci 0000:06:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.283433] pci 0000:06:00.0: PME# disabled [ 0.285085] pci 0000:03:03.0: bridge io port: [0xa000-0xafff] [ 0.285091] pci 0000:03:03.0: bridge 32bit mmio: [0xe9000000-0xe9ffffff] [ 0.285100] pci 0000:03:03.0: bridge 64bit mmio pref: [0xec100000-0xec1fffff] [ 0.285173] pci 0000:07:00.0: reg 10 io port: [0xb000-0xb0ff] [ 0.285196] pci 0000:07:00.0: reg 18 64bit mmio: [0xec210000-0xec210fff] [ 0.285213] pci 0000:07:00.0: reg 20 64bit mmio: [0xec200000-0xec20ffff] [ 0.285222] pci 0000:07:00.0: reg 30 32bit mmio: [0x000000-0x00ffff] [ 0.285283] pci 0000:07:00.0: supports D1 D2 [ 0.285285] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.285431] pci 0000:07:00.0: PME# disabled [ 0.287085] pci 0000:03:04.0: bridge io port: [0xb000-0xbfff] [ 0.287091] pci 0000:03:04.0: bridge 32bit mmio: [0xea000000-0xeaffffff] [ 0.287100] pci 0000:03:04.0: bridge 64bit mmio pref: [0xec200000-0xec2fffff] [ 0.287173] pci 0000:08:00.0: reg 10 io port: [0xc000-0xc0ff] [ 0.287197] pci 0000:08:00.0: reg 18 64bit mmio: [0xec310000-0xec310fff] [ 0.287213] pci 0000:08:00.0: reg 20 64bit mmio: [0xec300000-0xec30ffff] [ 0.287222] pci 0000:08:00.0: reg 30 32bit mmio: [0x000000-0x00ffff] [ 0.287284] pci 0000:08:00.0: supports D1 D2 [ 0.287285] pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.287432] pci 0000:08:00.0: PME# disabled [ 0.289085] pci 0000:03:05.0: bridge io port: [0xc000-0xcfff] [ 0.289090] pci 0000:03:05.0: bridge 32bit mmio: [0xeb000000-0xebffffff] [ 0.289099] pci 0000:03:05.0: bridge 64bit mmio pref: [0xec300000-0xec3fffff] [ 0.289318] pci 0000:0a:00.0: reg 24 32bit mmio: [0xec400000-0xec401fff] [ 0.289365] pci 0000:0a:00.0: PME# supported from D3hot [ 0.289506] pci 0000:0a:00.0: PME# disabled [ 0.289672] pci 0000:0a:00.1: reg 10 io port: [0xd000-0xd007] [ 0.289680] pci 0000:0a:00.1: reg 14 io port: [0xd100-0xd103] [ 0.289689] pci 0000:0a:00.1: reg 18 io port: [0xd200-0xd207] [ 0.289697] pci 0000:0a:00.1: reg 1c io port: [0xd300-0xd303] [ 0.289705] pci 0000:0a:00.1: reg 20 io port: [0xd400-0xd40f] [ 0.289785] pci 0000:0a:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.290059] pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff] [ 0.290062] pci 0000:00:1c.4: bridge 32bit mmio: [0xec400000-0xec4fffff] [ 0.290095] pci 0000:0b:06.0: reg 10 32bit mmio: [0xec504000-0xec5047ff] [ 0.290101] pci 0000:0b:06.0: reg 14 32bit mmio: [0xec500000-0xec503fff] [ 0.290172] pci 0000:0b:06.0: supports D1 D2 [ 0.290173] pci 0000:0b:06.0: PME# supported from D0 D1 D2 D3hot [ 0.290316] pci 0000:0b:06.0: PME# disabled [ 0.290483] pci 0000:00:1e.0: transparent bridge [ 0.290621] pci 0000:00:1e.0: bridge 32bit mmio: [0xec500000-0xec5fffff] [ 0.290639] pci_bus 0000:00: on NUMA node 0 [ 0.290648] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.290835] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 0.290963] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 0.291027] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 0.308962] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14 *15) [ 0.309704] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 *14 15) [ 0.310479] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 0.311165] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 0.312039] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. [ 0.312845] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 9 10 11 12 14 15) [ 0.313597] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 0.314397] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 *7 9 10 11 12 14 15) [ 0.315039] SCSI subsystem initialized [ 0.315970] libata version 3.00 loaded. [ 0.316016] usbcore: registered new interface driver usbfs [ 0.316151] usbcore: registered new interface driver hub [ 0.316151] usbcore: registered new device driver usb [ 0.316984] PCI: Using ACPI for IRQ routing [ 0.325065] pnp: PnP ACPI init [ 0.325200] ACPI: bus type pnp registered [ 0.328485] pnp: PnP ACPI: found 12 devices [ 0.328641] ACPI: ACPI bus type pnp unregistered [ 0.328791] system 00:01: ioport range 0x4d0-0x4d1 has been reserved [ 0.328934] system 00:01: ioport range 0x290-0x29f has been reserved [ 0.329077] system 00:01: ioport range 0x800-0x805 has been reserved [ 0.329220] system 00:01: ioport range 0x290-0x294 has been reserved [ 0.329367] system 00:01: ioport range 0x880-0x88f has been reserved [ 0.329510] system 00:01: ioport range 0x4c0-0x4ff could not be reserved [ 0.329695] system 00:08: ioport range 0x400-0x4bf could not be reserved [ 0.329842] system 00:09: iomem range 0xe0000000-0xe3ffffff has been reserved [ 0.329991] system 00:0a: iomem range 0xd2000-0xd3fff has been reserved [ 0.330134] system 00:0a: iomem range 0xf0000-0xf7fff could not be reserved [ 0.330282] system 00:0a: iomem range 0xf8000-0xfbfff could not be reserved [ 0.330427] system 00:0a: iomem range 0xfc000-0xfffff could not be reserved [ 0.330591] system 00:0a: iomem range 0xcfeb0000-0xcfefffff could not be reserved [ 0.330830] system 00:0a: iomem range 0x0-0x9ffff could not be reserved [ 0.330974] system 00:0a: iomem range 0x100000-0xcfeaffff could not be reserved [ 0.331202] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved [ 0.331351] system 00:0a: iomem range 0xfed10000-0xfed1dfff has been reserved [ 0.331497] system 00:0a: iomem range 0xfed20000-0xfed8ffff has been reserved [ 0.331644] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.331794] system 00:0a: iomem range 0xffb00000-0xffb7ffff has been reserved [ 0.331940] system 00:0a: iomem range 0xfff00000-0xffffffff has been reserved [ 0.332086] system 00:0a: iomem range 0xe0000-0xeffff has been reserved [ 0.366929] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 [ 0.367088] pci 0000:00:01.0: IO window: 0x8000-0x8fff [ 0.367246] pci 0000:00:01.0: MEM window: 0xe4000000-0xe7ffffff [ 0.367392] pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff [ 0.367624] pci 0000:03:01.0: PCI bridge, secondary bus 0000:04 [ 0.367764] pci 0000:03:01.0: IO window: disabled [ 0.367904] pci 0000:03:01.0: MEM window: disabled [ 0.368062] pci 0000:03:01.0: PREFETCH window: disabled [ 0.368224] pci 0000:03:02.0: PCI bridge, secondary bus 0000:05 [ 0.368369] pci 0000:03:02.0: IO window: 0x9000-0x9fff [ 0.368512] pci 0000:03:02.0: MEM window: 0xe8000000-0xe8ffffff [ 0.368656] pci 0000:03:02.0: PREFETCH window: 0x000000ec000000-0x000000ec0fffff [ 0.368893] pci 0000:03:03.0: PCI bridge, secondary bus 0000:06 [ 0.369035] pci 0000:03:03.0: IO window: 0xa000-0xafff [ 0.369190] pci 0000:03:03.0: MEM window: 0xe9000000-0xe9ffffff [ 0.369347] pci 0000:03:03.0: PREFETCH window: 0x000000ec100000-0x000000ec1fffff [ 0.369583] pci 0000:03:04.0: PCI bridge, secondary bus 0000:07 [ 0.369725] pci 0000:03:04.0: IO window: 0xb000-0xbfff [ 0.369868] pci 0000:03:04.0: MEM window: 0xea000000-0xeaffffff [ 0.370012] pci 0000:03:04.0: PREFETCH window: 0x000000ec200000-0x000000ec2fffff [ 0.370250] pci 0000:03:05.0: PCI bridge, secondary bus 0000:08 [ 0.370406] pci 0000:03:05.0: IO window: 0xc000-0xcfff [ 0.370548] pci 0000:03:05.0: MEM window: 0xeb000000-0xebffffff [ 0.370692] pci 0000:03:05.0: PREFETCH window: 0x000000ec300000-0x000000ec3fffff [ 0.370928] pci 0000:03:06.0: PCI bridge, secondary bus 0000:09 [ 0.371067] pci 0000:03:06.0: IO window: disabled [ 0.371217] pci 0000:03:06.0: MEM window: disabled [ 0.371368] pci 0000:03:06.0: PREFETCH window: disabled [ 0.371512] pci 0000:02:00.0: PCI bridge, secondary bus 0000:03 [ 0.371653] pci 0000:02:00.0: IO window: 0x9000-0xcfff [ 0.371796] pci 0000:02:00.0: MEM window: 0xe8000000-0xebffffff [ 0.371940] pci 0000:02:00.0: PREFETCH window: 0x000000ec000000-0x000000ec3fffff [ 0.372177] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02 [ 0.372330] pci 0000:00:1c.0: IO window: 0x9000-0xcfff [ 0.372480] pci 0000:00:1c.0: MEM window: 0xe8000000-0xebffffff [ 0.372622] pci 0000:00:1c.0: PREFETCH window: 0x000000ec000000-0x000000ec3fffff [ 0.372855] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0a [ 0.372996] pci 0000:00:1c.4: IO window: 0xd000-0xdfff [ 0.373135] pci 0000:00:1c.4: MEM window: 0xec400000-0xec4fffff [ 0.373280] pci 0000:00:1c.4: PREFETCH window: disabled [ 0.373435] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0b [ 0.373574] pci 0000:00:1e.0: IO window: disabled [ 0.373713] pci 0000:00:1e.0: MEM window: 0xec500000-0xec5fffff [ 0.373856] pci 0000:00:1e.0: PREFETCH window: disabled [ 0.374002] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.374149] pci 0000:00:01.0: setting latency timer to 64 [ 0.374154] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.374313] pci 0000:00:1c.0: setting latency timer to 64 [ 0.374325] pci 0000:02:00.0: setting latency timer to 64 [ 0.374336] pci 0000:03:01.0: setting latency timer to 64 [ 0.374348] pci 0000:03:02.0: setting latency timer to 64 [ 0.374359] pci 0000:03:03.0: setting latency timer to 64 [ 0.374370] pci 0000:03:04.0: setting latency timer to 64 [ 0.374381] pci 0000:03:05.0: setting latency timer to 64 [ 0.374393] pci 0000:03:06.0: setting latency timer to 64 [ 0.374399] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.374552] pci 0000:00:1c.4: setting latency timer to 64 [ 0.374558] pci 0000:00:1e.0: setting latency timer to 64 [ 0.374561] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.374563] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] [ 0.374565] pci_bus 0000:01: resource 0 io: [0x8000-0x8fff] [ 0.374568] pci_bus 0000:01: resource 1 mem: [0xe4000000-0xe7ffffff] [ 0.374571] pci_bus 0000:01: resource 2 mem: [0xd0000000-0xdfffffff] [ 0.374573] pci_bus 0000:01: resource 3 mem: [0x0-0x0] [ 0.374576] pci_bus 0000:02: resource 0 io: [0x9000-0xcfff] [ 0.374579] pci_bus 0000:02: resource 1 mem: [0xe8000000-0xebffffff] [ 0.374581] pci_bus 0000:02: resource 2 mem: [0xec000000-0xec3fffff] [ 0.374584] pci_bus 0000:02: resource 3 mem: [0x0-0x0] [ 0.374586] pci_bus 0000:03: resource 0 io: [0x9000-0xcfff] [ 0.374588] pci_bus 0000:03: resource 1 mem: [0xe8000000-0xebffffff] [ 0.374591] pci_bus 0000:03: resource 2 mem: [0xec000000-0xec3fffff] [ 0.374593] pci_bus 0000:03: resource 3 mem: [0x0-0x0] [ 0.374594] pci_bus 0000:04: resource 0 mem: [0x0-0x0] [ 0.374596] pci_bus 0000:04: resource 1 mem: [0x0-0x0] [ 0.374598] pci_bus 0000:04: resource 2 mem: [0x0-0x0] [ 0.374600] pci_bus 0000:04: resource 3 mem: [0x0-0x0] [ 0.374602] pci_bus 0000:05: resource 0 io: [0x9000-0x9fff] [ 0.374604] pci_bus 0000:05: resource 1 mem: [0xe8000000-0xe8ffffff] [ 0.374606] pci_bus 0000:05: resource 2 mem: [0xec000000-0xec0fffff] [ 0.374608] pci_bus 0000:05: resource 3 mem: [0x0-0x0] [ 0.374610] pci_bus 0000:06: resource 0 io: [0xa000-0xafff] [ 0.374612] pci_bus 0000:06: resource 1 mem: [0xe9000000-0xe9ffffff] [ 0.374614] pci_bus 0000:06: resource 2 mem: [0xec100000-0xec1fffff] [ 0.374616] pci_bus 0000:06: resource 3 mem: [0x0-0x0] [ 0.374618] pci_bus 0000:07: resource 0 io: [0xb000-0xbfff] [ 0.374620] pci_bus 0000:07: resource 1 mem: [0xea000000-0xeaffffff] [ 0.374622] pci_bus 0000:07: resource 2 mem: [0xec200000-0xec2fffff] [ 0.374624] pci_bus 0000:07: resource 3 mem: [0x0-0x0] [ 0.374626] pci_bus 0000:08: resource 0 io: [0xc000-0xcfff] [ 0.374628] pci_bus 0000:08: resource 1 mem: [0xeb000000-0xebffffff] [ 0.374630] pci_bus 0000:08: resource 2 mem: [0xec300000-0xec3fffff] [ 0.374632] pci_bus 0000:08: resource 3 mem: [0x0-0x0] [ 0.374634] pci_bus 0000:09: resource 0 mem: [0x0-0x0] [ 0.374635] pci_bus 0000:09: resource 1 mem: [0x0-0x0] [ 0.374637] pci_bus 0000:09: resource 2 mem: [0x0-0x0] [ 0.374639] pci_bus 0000:09: resource 3 mem: [0x0-0x0] [ 0.374641] pci_bus 0000:0a: resource 0 io: [0xd000-0xdfff] [ 0.374644] pci_bus 0000:0a: resource 1 mem: [0xec400000-0xec4fffff] [ 0.374646] pci_bus 0000:0a: resource 2 mem: [0x0-0x0] [ 0.374649] pci_bus 0000:0a: resource 3 mem: [0x0-0x0] [ 0.374651] pci_bus 0000:0b: resource 0 mem: [0x0-0x0] [ 0.374653] pci_bus 0000:0b: resource 1 mem: [0xec500000-0xec5fffff] [ 0.374656] pci_bus 0000:0b: resource 2 mem: [0x0-0x0] [ 0.374658] pci_bus 0000:0b: resource 3 io: [0x00-0xffff] [ 0.374661] pci_bus 0000:0b: resource 4 mem: [0x000000-0xffffffff] [ 0.374685] NET: Registered protocol family 2 [ 0.386573] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.386958] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.387446] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.387758] TCP: Hash tables configured (established 131072 bind 65536) [ 0.387901] TCP reno registered [ 0.390646] NET: Registered protocol family 1 [ 0.393094] audit: initializing netlink socket (disabled) [ 0.393237] type=2000 audit(1245410950.392:1): initialized [ 0.398705] highmem bounce pool size: 64 pages [ 0.398853] HugeTLB registered 4 MB page size, pre-allocated 0 pages [ 0.404767] fuse init (API version 7.11) [ 0.405223] msgmni has been set to 1699 [ 0.405617] cryptomgr_test used greatest stack depth: 7096 bytes left [ 0.406027] cryptomgr_test used greatest stack depth: 6836 bytes left [ 0.406189] alg: No test for stdrng (krng) [ 0.406482] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.406729] io scheduler noop registered [ 0.406870] io scheduler cfq registered (default) [ 0.407180] pci 0000:01:00.0: Boot video device [ 0.407348] pcieport-driver 0000:00:01.0: setting latency timer to 64 [ 0.407391] pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X [ 0.407560] pcieport-driver 0000:00:1c.0: setting latency timer to 64 [ 0.407617] pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X [ 0.407878] pcieport-driver 0000:00:1c.4: setting latency timer to 64 [ 0.407924] pcieport-driver 0000:00:1c.4: irq 26 for MSI/MSI-X [ 0.408188] pcieport-driver 0000:02:00.0: setting latency timer to 64 [ 0.408439] pcieport-driver 0000:03:01.0: setting latency timer to 64 [ 0.408531] pcieport-driver 0000:03:01.0: irq 27 for MSI/MSI-X [ 0.408836] pcieport-driver 0000:03:02.0: setting latency timer to 64 [ 0.408943] pcieport-driver 0000:03:02.0: irq 28 for MSI/MSI-X [ 0.409166] pcieport-driver 0000:03:03.0: setting latency timer to 64 [ 0.409257] pcieport-driver 0000:03:03.0: irq 29 for MSI/MSI-X [ 0.409454] pcieport-driver 0000:03:04.0: setting latency timer to 64 [ 0.409552] pcieport-driver 0000:03:04.0: irq 30 for MSI/MSI-X [ 0.409728] pcieport-driver 0000:03:05.0: setting latency timer to 64 [ 0.409854] pcieport-driver 0000:03:05.0: irq 31 for MSI/MSI-X [ 0.410087] pcieport-driver 0000:03:06.0: setting latency timer to 64 [ 0.410177] pcieport-driver 0000:03:06.0: irq 32 for MSI/MSI-X [ 0.415367] Non-volatile memory driver v1.3 [ 0.416002] uvesafb: failed to execute /sbin/v86d [ 0.416137] uvesafb: make sure that the v86d helper is installed and executable [ 0.416366] uvesafb: Getting VBE info block failed (eax=0x4f00, err=-2) [ 0.416509] uvesafb: vbe_init() failed with -22 [ 0.416646] uvesafb: probe of uvesafb.0 failed with error -22 [ 0.417441] ACPI: SSDT CFEE80C0, 022A (r1 PmRef Cpu0Ist 3000 INTL 20040311) [ 0.417996] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 0.418338] processor ACPI_CPU:00: registered as cooling_device0 [ 0.418491] ACPI: Processor [CPU0] (supports 8 throttling states) [ 0.418873] ACPI: SSDT CFEE8580, 0152 (r1 PmRef Cpu1Ist 3000 INTL 20040311) [ 0.421093] ACPI: CPU1 (power states: C1[C1] C2[C2]) [ 0.421380] processor ACPI_CPU:01: registered as cooling_device1 [ 0.421524] ACPI: Processor [CPU1] (supports 8 throttling states) [ 0.422001] ACPI: SSDT CFEE86E0, 0152 (r1 PmRef Cpu2Ist 3000 INTL 20040311) [ 0.422550] ACPI: CPU2 (power states: C1[C1] C2[C2]) [ 0.422874] processor ACPI_CPU:02: registered as cooling_device2 [ 0.423079] ACPI: Processor [CPU2] (supports 8 throttling states) [ 0.423494] ACPI: SSDT CFEE8840, 0152 (r1 PmRef Cpu3Ist 3000 INTL 20040311) [ 0.424004] ACPI: CPU3 (power states: C1[C1] C2[C2]) [ 0.424282] processor ACPI_CPU:03: registered as cooling_device3 [ 0.424425] ACPI: Processor [CPU3] (supports 8 throttling states) [ 0.426498] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.673237] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.674067] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.675476] loop: module loaded [ 0.675753] PPP generic driver version 2.4.2 [ 0.675996] PPP Deflate Compression module registered [ 0.676135] PPP BSD Compression module registered [ 0.676504] PPP MPPE Compression module registered [ 0.676662] NET: Registered protocol family 24 [ 0.676881] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 0.677053] r8169 0000:05:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 0.677213] r8169 0000:05:00.0: setting latency timer to 64 [ 0.677299] r8169 0000:05:00.0: irq 33 for MSI/MSI-X [ 0.677603] eth0: RTL8168c/8111c at 0xf7c2c000, 00:1f:d0:a0:cb:61, XID 3c4000c0 IRQ 33 [ 0.680657] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 0.680806] r8169 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.680979] r8169 0000:06:00.0: setting latency timer to 64 [ 0.681049] r8169 0000:06:00.0: irq 34 for MSI/MSI-X [ 0.681333] eth1: RTL8168c/8111c at 0xf7c28000, 00:1f:d0:a0:cb:63, XID 3c4000c0 IRQ 34 [ 0.684386] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 0.684533] r8169 0000:07:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.684689] r8169 0000:07:00.0: setting latency timer to 64 [ 0.684759] r8169 0000:07:00.0: irq 35 for MSI/MSI-X [ 0.685063] eth2: RTL8168c/8111c at 0xf7c30000, 00:1f:d0:a0:cb:71, XID 3c4000c0 IRQ 35 [ 0.688116] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 0.688264] r8169 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.688420] r8169 0000:08:00.0: setting latency timer to 64 [ 0.688490] r8169 0000:08:00.0: irq 36 for MSI/MSI-X [ 0.688801] eth3: RTL8168c/8111c at 0xf7c34000, 00:1f:d0:a0:cb:73, XID 3c4000c0 IRQ 36 [ 0.691966] Driver 'sd' needs updating - please use bus_type methods [ 0.692153] Driver 'sr' needs updating - please use bus_type methods [ 0.692422] ahci 0000:00:1f.2: version 3.0 [ 0.692430] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.692596] ahci 0000:00:1f.2: irq 37 for MSI/MSI-X [ 0.692630] ahci: SSS flag set, parallel bus scan disabled [ 0.692795] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 0.693040] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part ems [ 0.693273] ahci 0000:00:1f.2: setting latency timer to 64 [ 0.693543] scsi0 : ahci [ 0.693851] scsi1 : ahci [ 0.694155] scsi2 : ahci [ 0.694417] scsi3 : ahci [ 0.694718] scsi4 : ahci [ 0.694982] scsi5 : ahci [ 0.695348] ata1: SATA max UDMA/133 abar m2048@0xec606000 port 0xec606100 irq 37 [ 0.695580] ata2: SATA max UDMA/133 abar m2048@0xec606000 port 0xec606180 irq 37 [ 0.695820] ata3: SATA max UDMA/133 abar m2048@0xec606000 port 0xec606200 irq 37 [ 0.696072] ata4: SATA max UDMA/133 abar m2048@0xec606000 port 0xec606280 irq 37 [ 0.696300] ata5: SATA max UDMA/133 abar m2048@0xec606000 port 0xec606300 irq 37 [ 0.696530] ata6: SATA max UDMA/133 abar m2048@0xec606000 port 0xec606380 irq 37 [ 0.870906] Switched to high resolution mode on CPU 3 [ 0.870909] Switched to high resolution mode on CPU 0 [ 0.870911] Switched to high resolution mode on CPU 1 [ 0.870914] Switched to high resolution mode on CPU 2 [ 0.999149] ata1: SATA link down (SStatus 0 SControl 300) [ 1.314270] ata2: SATA link down (SStatus 0 SControl 300) [ 1.783021] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.811733] ata3.00: HPA detected: current 312579695, native 312581808 [ 1.811883] ata3.00: ATA-8: ST3160813AS, CC2H, max UDMA/133 [ 1.812033] ata3.00: 312579695 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 1.853943] ata3.00: configured for UDMA/133 [ 1.864120] scsi 2:0:0:0: Direct-Access ATA ST3160813AS CC2H PQ: 0 ANSI: 5 [ 1.864617] sd 2:0:0:0: [sda] 312579695 512-byte hardware sectors: (160 GB/149 GiB) [ 1.864863] sd 2:0:0:0: [sda] Write Protect is off [ 1.865010] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.865030] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.865322] sd 2:0:0:0: [sda] 312579695 512-byte hardware sectors: (160 GB/149 GiB) [ 1.865601] sd 2:0:0:0: [sda] Write Protect is off [ 1.865736] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.865755] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.865992] sda: sda1 sda2 sda3 [ 1.889827] sd 2:0:0:0: [sda] Attached SCSI disk [ 1.890145] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 2.348022] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.349562] ata4.00: HPA detected: current 976771055, native 976773168 [ 2.349711] ata4.00: ATA-8: ST3500320AS, SD81, max UDMA/133 [ 2.349862] ata4.00: 976771055 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 2.351788] ata4.00: configured for UDMA/133 [ 2.362135] scsi 3:0:0:0: Direct-Access ATA ST3500320AS SD81 PQ: 0 ANSI: 5 [ 2.362671] sd 3:0:0:0: [sdb] 976771055 512-byte hardware sectors: (500 GB/465 GiB) [ 2.362913] sd 3:0:0:0: [sdb] Write Protect is off [ 2.363049] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2.363069] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.363373] sd 3:0:0:0: [sdb] 976771055 512-byte hardware sectors: (500 GB/465 GiB) [ 2.363612] sd 3:0:0:0: [sdb] Write Protect is off [ 2.363747] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2.363767] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.364003] sdb: sdb1 sdb2 sdb3 [ 2.376366] sd 3:0:0:0: [sdb] Attached SCSI disk [ 2.376670] sd 3:0:0:0: Attached scsi generic sg1 type 0 [ 2.834021] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.834739] ata5.00: HPA detected: current 488395055, native 488397168 [ 2.834915] ata5.00: ATA-7: ST3250410AS, 3.AAA, max UDMA/133 [ 2.835071] ata5.00: 488395055 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 2.835979] ata5.00: configured for UDMA/133 [ 2.846100] scsi 4:0:0:0: Direct-Access ATA ST3250410AS 3.AA PQ: 0 ANSI: 5 [ 2.846633] sd 4:0:0:0: [sdc] 488395055 512-byte hardware sectors: (250 GB/232 GiB) [ 2.846883] sd 4:0:0:0: [sdc] Write Protect is off [ 2.847018] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 2.847038] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.847334] sd 4:0:0:0: [sdc] 488395055 512-byte hardware sectors: (250 GB/232 GiB) [ 2.847573] sd 4:0:0:0: [sdc] Write Protect is off [ 2.847708] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 2.847727] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.847963] sdc: sdc1 [ 2.863608] sd 4:0:0:0: [sdc] Attached SCSI disk [ 2.863850] sd 4:0:0:0: Attached scsi generic sg2 type 0 [ 3.321021] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 3.321762] ata6.00: HPA detected: current 488395055, native 488397168 [ 3.321928] ata6.00: ATA-7: ST3250410AS, 3.AAC, max UDMA/133 [ 3.322082] ata6.00: 488395055 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 3.322931] ata6.00: configured for UDMA/133 [ 3.333102] scsi 5:0:0:0: Direct-Access ATA ST3250410AS 3.AA PQ: 0 ANSI: 5 [ 3.333632] sd 5:0:0:0: [sdd] 488395055 512-byte hardware sectors: (250 GB/232 GiB) [ 3.333882] sd 5:0:0:0: [sdd] Write Protect is off [ 3.334017] sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [ 3.334037] sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.334334] sd 5:0:0:0: [sdd] 488395055 512-byte hardware sectors: (250 GB/232 GiB) [ 3.334574] sd 5:0:0:0: [sdd] Write Protect is off [ 3.334710] sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [ 3.334729] sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.334966] sdd: sdd1 [ 3.351081] sdd: p1 size 488406082 limited to end of disk [ 3.351458] sd 5:0:0:0: [sdd] Attached SCSI disk [ 3.351701] sd 5:0:0:0: Attached scsi generic sg3 type 0 [ 3.351972] ahci 0000:0a:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.362282] ahci 0000:0a:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode [ 3.362546] ahci 0000:0a:00.0: flags: 64bit ncq pm led clo pmp pio slum part [ 3.362695] ahci 0000:0a:00.0: setting latency timer to 64 [ 3.362862] scsi6 : ahci [ 3.363235] scsi7 : ahci [ 3.363564] ata7: SATA max UDMA/133 abar m8192@0xec400000 port 0xec400100 irq 16 [ 3.363794] ata8: SATA max UDMA/133 abar m8192@0xec400000 port 0xec400180 irq 16 [ 9.635033] ata7: link is slow to respond, please be patient (ready=0) [ 13.409073] ata7: softreset failed (device not ready) [ 13.409222] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 13.409376] ata7: link online but device misclassified, retrying [ 19.681032] ata7: link is slow to respond, please be patient (ready=0) [ 23.455072] ata7: softreset failed (device not ready) [ 23.455220] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 23.455375] ata7: link online but device misclassified, retrying [ 29.727052] ata7: link is slow to respond, please be patient (ready=0) [ 58.491032] ata7: softreset failed (device not ready) [ 58.491180] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 58.491336] ata7: link online but device misclassified, retrying [ 58.491492] ata7: limiting SATA link speed to 1.5 Gbps [ 63.539032] ata7: softreset failed (device not ready) [ 63.539181] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 63.539336] ata7: link online but device misclassified, device detection might fail [ 69.822052] ata8: link is slow to respond, please be patient (ready=0) [ 73.596052] ata8: softreset failed (device not ready) [ 73.596200] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 73.596354] ata8: link online but device misclassified, retrying [ 79.868029] ata8: link is slow to respond, please be patient (ready=0) [ 83.643073] ata8: softreset failed (device not ready) [ 83.643221] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 83.643375] ata8: link online but device misclassified, retrying [ 89.915032] ata8: link is slow to respond, please be patient (ready=0) [ 118.682072] ata8: softreset failed (device not ready) [ 118.682220] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 118.682376] ata8: link online but device misclassified, retrying [ 118.682532] ata8: limiting SATA link speed to 1.5 Gbps [ 123.730073] ata8: softreset failed (device not ready) [ 123.730221] ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 123.730377] ata8: link online but device misclassified, device detection might fail [ 123.741402] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 123.741572] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 123.741734] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 123.741737] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 123.741981] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 123.746112] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported [ 123.746125] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xec605000 [ 123.755266] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 123.755434] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 123.755581] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 123.755822] usb usb1: Product: EHCI Host Controller [ 123.755957] usb usb1: Manufacturer: Linux 2.6.29-gentoo-r5 ehci_hcd [ 123.756122] usb usb1: SerialNumber: 0000:00:1a.7 [ 123.756390] usb usb1: configuration #1 chosen from 1 choice [ 123.756630] hub 1-0:1.0: USB hub found [ 123.756785] hub 1-0:1.0: 6 ports detected [ 123.757174] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 123.757383] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 123.757386] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 123.757614] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 123.761738] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 123.761748] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xec604000 [ 123.771017] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 123.771183] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 123.771355] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 123.771596] usb usb2: Product: EHCI Host Controller [ 123.771731] usb usb2: Manufacturer: Linux 2.6.29-gentoo-r5 ehci_hcd [ 123.771873] usb usb2: SerialNumber: 0000:00:1d.7 [ 123.772107] usb usb2: configuration #1 chosen from 1 choice [ 123.772365] hub 2-0:1.0: USB hub found [ 123.772530] hub 2-0:1.0: 6 ports detected [ 123.772911] uhci_hcd: USB Universal Host Controller Interface driver [ 123.773111] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 123.773278] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 123.773281] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 123.773485] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 123.773771] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e100 [ 123.773934] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 123.774084] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 123.774360] usb usb3: Product: UHCI Host Controller [ 123.774514] usb usb3: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 123.774656] usb usb3: SerialNumber: 0000:00:1a.0 [ 123.774878] usb usb3: configuration #1 chosen from 1 choice [ 123.775107] hub 3-0:1.0: USB hub found [ 123.775291] hub 3-0:1.0: 2 ports detected [ 123.775616] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 123.775764] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 123.775767] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 123.775971] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 123.776288] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000e200 [ 123.776451] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 123.776605] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 123.776833] usb usb4: Product: UHCI Host Controller [ 123.776969] usb usb4: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 123.777116] usb usb4: SerialNumber: 0000:00:1a.1 [ 123.777386] usb usb4: configuration #1 chosen from 1 choice [ 123.777624] hub 4-0:1.0: USB hub found [ 123.777780] hub 4-0:1.0: 2 ports detected [ 123.778087] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 123.778262] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 123.778274] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 123.778509] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 123.778787] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000e000 [ 123.778950] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 123.779093] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 123.779342] usb usb5: Product: UHCI Host Controller [ 123.779497] usb usb5: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 123.779639] usb usb5: SerialNumber: 0000:00:1a.2 [ 123.779862] usb usb5: configuration #1 chosen from 1 choice [ 123.780091] hub 5-0:1.0: USB hub found [ 123.780255] hub 5-0:1.0: 2 ports detected [ 123.780582] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 123.780741] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 123.780744] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 123.780948] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 123.781259] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e300 [ 123.781430] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 123.781585] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 123.781814] usb usb6: Product: UHCI Host Controller [ 123.781950] usb usb6: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 123.782114] usb usb6: SerialNumber: 0000:00:1d.0 [ 123.782352] usb usb6: configuration #1 chosen from 1 choice [ 123.782611] hub 6-0:1.0: USB hub found [ 123.782756] hub 6-0:1.0: 2 ports detected [ 123.783067] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 123.783241] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 123.783244] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 123.783474] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 123.783766] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e400 [ 123.783929] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 123.784073] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 123.784331] usb usb7: Product: UHCI Host Controller [ 123.784476] usb usb7: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 123.784617] usb usb7: SerialNumber: 0000:00:1d.1 [ 123.784850] usb usb7: configuration #1 chosen from 1 choice [ 123.785079] hub 7-0:1.0: USB hub found [ 123.785243] hub 7-0:1.0: 2 ports detected [ 123.785575] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 123.785733] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 123.785736] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 123.785956] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 123.786258] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e500 [ 123.786430] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 123.786584] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 123.786812] usb usb8: Product: UHCI Host Controller [ 123.786948] usb usb8: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 123.787113] usb usb8: SerialNumber: 0000:00:1d.2 [ 123.787362] usb usb8: configuration #1 chosen from 1 choice [ 123.787613] hub 8-0:1.0: USB hub found [ 123.787758] hub 8-0:1.0: 2 ports detected [ 123.788127] Initializing USB Mass Storage driver... [ 123.788384] usbcore: registered new interface driver usb-storage [ 123.788556] USB Mass Storage support registered. [ 123.788941] PNP: No PS/2 controller found. Probing ports directly. [ 123.789529] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 123.789670] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 123.789919] mice: PS/2 mouse device common for all mice [ 123.790282] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 123.791244] cpuidle: using governor ladder [ 123.792391] cpuidle: using governor menu [ 123.792559] No iBFT detected. [ 123.794200] usbcore: registered new interface driver hiddev [ 123.794461] usbcore: registered new interface driver usbhid [ 123.794632] usbhid: v2.6:USB HID core driver [ 123.794873] Advanced Linux Sound Architecture Driver Version 1.0.18a. [ 123.795544] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 123.795805] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 123.806164] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS... [ 123.833077] ALSA device list: [ 123.833216] #0: HDA Intel at 0xec600000 irq 22 [ 123.833662] TCP cubic registered [ 123.833791] Initializing XFRM netlink socket [ 123.833929] NET: Registered protocol family 17 [ 123.839058] Using IPI No-Shortcut mode [ 123.839498] registered taskstats version 1 [ 123.966765] EXT3-fs: sda3: couldn't mount because of unsupported optional features (240). [ 123.967669] EXT2-fs: sda3: couldn't mount because of unsupported optional features (240). [ 123.977215] EXT4-fs: barriers enabled [ 123.997996] kjournald2 starting: pid 809, dev sda3:8, commit interval 5 seconds [ 123.998252] EXT4-fs: delayed allocation enabled [ 123.998401] EXT4-fs: file extents enabled [ 124.008390] EXT4-fs: mballoc enabled [ 124.008520] EXT4-fs: mounted filesystem sda3 with ordered data mode [ 124.008669] VFS: Mounted root (ext4 filesystem) readonly on device 8:3. [ 124.008901] Freeing unused kernel memory: 324k freed [ 124.009114] Write protecting the kernel text: 3788k [ 124.009295] Write protecting the kernel read-only data: 1320k [ 124.046852] khelper used greatest stack depth: 6436 bytes left [ 124.262025] usb 2-2: new high speed USB device using ehci_hcd and address 2 [ 124.378479] usb 2-2: New USB device found, idVendor=058f, idProduct=6387 [ 124.378629] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 124.378788] usb 2-2: Product: Mass Storage Device [ 124.378923] usb 2-2: Manufacturer: JetFlash [ 124.379058] usb 2-2: SerialNumber: Q3NWCT2T [ 124.379313] usb 2-2: configuration #1 chosen from 1 choice [ 124.379803] scsi8 : SCSI emulation for USB Mass Storage devices [ 124.381830] usb-storage: device found at 2 [ 124.381833] usb-storage: waiting for device to settle before scanning [ 124.417633] stty used greatest stack depth: 6052 bytes left [ 124.587147] usb 4-1: new full speed USB device using uhci_hcd and address 2 [ 124.757540] usb 4-1: New USB device found, idVendor=046d, idProduct=c51a [ 124.757544] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 124.757548] usb 4-1: Product: USB Receiver [ 124.757550] usb 4-1: Manufacturer: Logitech [ 124.757631] usb 4-1: configuration #1 chosen from 1 choice [ 124.765808] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/input/input0 [ 124.772304] generic-usb 0003:046D:C51A.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1a.1-1/input0 [ 124.777648] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.1/input/input1 [ 124.783228] generic-usb 0003:046D:C51A.0002: input,hiddev96,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1a.1-1/input1 [ 124.990160] usb 5-1: new full speed USB device using uhci_hcd and address 2 [ 125.143186] usb 5-1: New USB device found, idVendor=046d, idProduct=c223 [ 125.143190] usb 5-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 125.143193] usb 5-1: Product: G11 Keyboard [ 125.143267] usb 5-1: configuration #1 chosen from 1 choice [ 125.146447] hub 5-1:1.0: USB hub found [ 125.148070] hub 5-1:1.0: 4 ports detected [ 125.428103] usb 5-1.1: new low speed USB device using uhci_hcd and address 3 [ 125.550104] usb 5-1.1: New USB device found, idVendor=046d, idProduct=c221 [ 125.550109] usb 5-1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 125.550113] usb 5-1.1: Product: Gaming Keyboard [ 125.550226] usb 5-1.1: configuration #1 chosen from 1 choice [ 125.567367] input: Gaming Keyboard as /devices/pci0000:00/0000:00:1a.2/usb5/5-1/5-1.1/5-1.1:1.0/input/input2 [ 125.575081] generic-usb 0003:046D:C221.0003: input,hidraw2: USB HID v1.10 Keyboard [Gaming Keyboard] on usb-0000:00:1a.2-1.1/input0 [ 125.608182] input: Gaming Keyboard as /devices/pci0000:00/0000:00:1a.2/usb5/5-1/5-1.1/5-1.1:1.1/input/input3 [ 125.615243] generic-usb 0003:046D:C221.0004: input,hiddev97,hidraw3: USB HID v1.10 Device [Gaming Keyboard] on usb-0000:00:1a.2-1.1/input1 [ 125.668440] nvidia: module license 'NVIDIA' taints kernel. [ 125.682124] usb 5-1.4: new full speed USB device using uhci_hcd and address 4 [ 125.806130] usb 5-1.4: New USB device found, idVendor=046d, idProduct=c225 [ 125.806136] usb 5-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 125.806139] usb 5-1.4: Product: G11 Keyboard [ 125.806206] usb 5-1.4: configuration #1 chosen from 1 choice [ 125.815210] input: G11 Keyboard as /devices/pci0000:00/0000:00:1a.2/usb5/5-1/5-1.4/5-1.4:1.0/input/input4 [ 125.922379] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 125.922385] nvidia 0000:01:00.0: setting latency timer to 64 [ 125.923159] NVRM: loading NVIDIA UNIX x86 Kernel Module 180.29 Wed Feb 4 23:44:25 PST 2009 [ 125.929512] generic-usb 0003:046D:C225.0005: input,hiddev98,hidraw4: USB HID v1.11 Keypad [G11 Keyboard] on usb-0000:00:1a.2-1.4/input0 [ 126.143864] EXT4 FS on sda3, internal journal on sda3:8 [ 126.200002] mount used greatest stack depth: 5464 bytes left [ 127.548103] Adding 530136k swap on /dev/sda2. Priority:-1 extents:1 across:530136k [ 129.382049] scsi 8:0:0:0: Direct-Access JetFlash Transcend 8GB 8.07 PQ: 0 ANSI: 2 [ 129.384778] sd 8:0:0:0: [sde] 15687680 512-byte hardware sectors: (8.03 GB/7.48 GiB) [ 129.385276] sd 8:0:0:0: [sde] Write Protect is off [ 129.385278] sd 8:0:0:0: [sde] Mode Sense: 03 00 00 00 [ 129.385280] sd 8:0:0:0: [sde] Assuming drive cache: write through [ 129.386896] sd 8:0:0:0: [sde] 15687680 512-byte hardware sectors: (8.03 GB/7.48 GiB) [ 129.387680] sd 8:0:0:0: [sde] Write Protect is off [ 129.387682] sd 8:0:0:0: [sde] Mode Sense: 03 00 00 00 [ 129.387684] sd 8:0:0:0: [sde] Assuming drive cache: write through [ 129.387686] sde: sde1 [ 129.799064] sd 8:0:0:0: [sde] Attached SCSI removable disk [ 129.799124] sd 8:0:0:0: Attached scsi generic sg4 type 0 [ 129.803121] usb-storage: device scan complete [ 134.456698] r8169: eth0: link up [ 134.456704] r8169: eth0: link up [ 144.502372] IRQ 16/nvidia: IRQF_DISABLED is not guaranteed on shared IRQs
# dmidecode 2.9 SMBIOS 2.4 present. 37 structures occupying 1196 bytes. Table at 0x000F0100. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: Award Software International, Inc. Version: F12 Release Date: 09/30/2008 Address: 0xE0000 Runtime Size: 128 kB ROM Size: 1024 kB Characteristics: PCI is supported PNP is supported BIOS is upgradeable BIOS shadowing is allowed Boot from CD is supported Selectable boot is supported EDD is supported 5.25"/360 KB floppy services are supported (int 13h) 5.25"/1.2 MB floppy services are supported (int 13h) 3.5"/720 KB floppy services are supported (int 13h) 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported Targeted content distribution is supported Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: Gigabyte Technology Co., Ltd. Product Name: EP45-DQ6 Version: Serial Number: UUID: 00000000-0000-0000-0000-001FD0A0CB73 Wake-up Type: Power Switch SKU Number: Family: Handle 0x0002, DMI type 2, 8 bytes Base Board Information Manufacturer: Gigabyte Technology Co., Ltd. Product Name: EP45-DQ6 Version: x.x Serial Number: Handle 0x0003, DMI type 3, 17 bytes Chassis Information Manufacturer: Gigabyte Technology Co., Ltd. Type: Desktop Lock: Not Present Version: Serial Number: Asset Tag: Boot-up State: Unknown Power Supply State: Unknown Thermal State: Unknown Security Status: Unknown OEM Information: 0x00000000 Handle 0x0004, DMI type 4, 35 bytes Processor Information Socket Designation: Socket 775 Type: Central Processor Family: Other Manufacturer: Intel ID: F7 06 00 00 FF FB EB BF Version: Intel(R) Core(TM)2 Quad CPU Voltage: 1.0 V External Clock: 266 MHz Max Speed: 4000 MHz Current Speed: 2133 MHz Status: Populated, Enabled Upgrade: Socket 478 L1 Cache Handle: 0x000A L2 Cache Handle: 0x000B L3 Cache Handle: Not Provided Serial Number: Asset Tag: Part Number: Handle 0x0005, DMI type 5, 24 bytes Memory Controller Information Error Detecting Method: 8-bit Parity Error Correcting Capabilities: None Supported Interleave: One-way Interleave Current Interleave: One-way Interleave Maximum Memory Module Size: 1024 MB Maximum Total Memory Size: 4096 MB Supported Speeds: Other Supported Memory Types: Other Memory Module Voltage: 5.0 V Associated Memory Slots: 4 0x0006 0x0007 0x0008 0x0009 Enabled Error Correcting Capabilities: None Handle 0x0006, DMI type 6, 12 bytes Memory Module Information Socket Designation: A0 Bank Connections: 1 Current Speed: Unknown Type: Other Installed Size: 1024 MB (Single-bank Connection) Enabled Size: 1024 MB (Single-bank Connection) Error Status: OK Handle 0x0007, DMI type 6, 12 bytes Memory Module Information Socket Designation: A1 Bank Connections: 2 Current Speed: Unknown Type: Other Installed Size: 1024 MB (Single-bank Connection) Enabled Size: 1024 MB (Single-bank Connection) Error Status: OK Handle 0x0008, DMI type 6, 12 bytes Memory Module Information Socket Designation: A2 Bank Connections: 3 Current Speed: Unknown Type: Other Installed Size: 1024 MB (Single-bank Connection) Enabled Size: 1024 MB (Single-bank Connection) Error Status: OK Handle 0x0009, DMI type 6, 12 bytes Memory Module Information Socket Designation: A3 Bank Connections: 4 Current Speed: Unknown Type: Other Installed Size: 1024 MB (Single-bank Connection) Enabled Size: 1024 MB (Single-bank Connection) Error Status: OK Handle 0x000A, DMI type 7, 19 bytes Cache Information Socket Designation: Internal Cache Configuration: Enabled, Not Socketed, Level 1 Operational Mode: Write Back Location: Internal Installed Size: 64 KB Maximum Size: 64 KB Supported SRAM Types: Synchronous Installed SRAM Type: Synchronous Speed: Unknown Error Correction Type: Unknown System Type: Unknown Associativity: Unknown Handle 0x000B, DMI type 7, 19 bytes Cache Information Socket Designation: External Cache Configuration: Enabled, Not Socketed, Level 2 Operational Mode: Write Back Location: Internal Installed Size: 4096 KB Maximum Size: 2048 KB Supported SRAM Types: Synchronous Installed SRAM Type: Synchronous Speed: Unknown Error Correction Type: Unknown System Type: Unknown Associativity: Unknown Handle 0x000C, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: PRIMARY IDE Internal Connector Type: On Board IDE External Reference Designator: External Connector Type: None Port Type: Other Handle 0x000D, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: SECONDARY IDE Internal Connector Type: On Board IDE External Reference Designator: External Connector Type: None Port Type: Other Handle 0x000E, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: FDD Internal Connector Type: On Board Floppy External Reference Designator: External Connector Type: None Port Type: 8251 FIFO Compatible Handle 0x000F, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: COM1 Internal Connector Type: 9 Pin Dual Inline (pin 10 cut) External Reference Designator: External Connector Type: DB-9 male Port Type: Serial Port 16450 Compatible Handle 0x0010, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: COM2 Internal Connector Type: 9 Pin Dual Inline (pin 10 cut) External Reference Designator: External Connector Type: DB-9 male Port Type: Serial Port 16450 Compatible Handle 0x0011, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: LPT1 Internal Connector Type: DB-25 female External Reference Designator: External Connector Type: DB-25 female Port Type: Parallel Port ECP/EPP Handle 0x0012, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Keyboard Internal Connector Type: Other External Reference Designator: External Connector Type: PS/2 Port Type: Keyboard Port Handle 0x0013, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: PS/2 Mouse Internal Connector Type: PS/2 External Reference Designator: Detected External Connector Type: PS/2 Port Type: Mouse Port Handle 0x0014, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: USB Internal Connector Type: None External Reference Designator: External Connector Type: Access Bus (USB) Port Type: USB Handle 0x0015, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: USB Internal Connector Type: None External Reference Designator: External Connector Type: Access Bus (USB) Port Type: USB Handle 0x0016, DMI type 9, 13 bytes System Slot Information Designation: PCI Type: 32-bit PCI Current Usage: Available Length: Long ID: 0 Characteristics: 5.0 V is provided 3.3 V is provided PME signal is supported SMBus signal is supported Handle 0x0017, DMI type 13, 22 bytes BIOS Language Information Installable Languages: 3 n|US|iso8859-1 n|US|iso8859-1 r|CA|iso8859-1 Currently Installed Language: n|US|iso8859-1 Handle 0x0018, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 4 GB Error Information Handle: Not Provided Number Of Devices: 4 Handle 0x0019, DMI type 17, 27 bytes Memory Device Array Handle: 0x0018 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 1024 MB Form Factor: DIMM Set: None Locator: A0 Bank Locator: Bank0/1 Type: Unknown Type Detail: None Speed: 800 MHz (1.2 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x001A, DMI type 17, 27 bytes Memory Device Array Handle: 0x0018 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 1024 MB Form Factor: DIMM Set: None Locator: A1 Bank Locator: Bank2/3 Type: Unknown Type Detail: None Speed: 800 MHz (1.2 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x001B, DMI type 17, 27 bytes Memory Device Array Handle: 0x0018 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 1024 MB Form Factor: DIMM Set: None Locator: A2 Bank Locator: Bank4/5 Type: Unknown Type Detail: None Speed: 800 MHz (1.2 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x001C, DMI type 17, 27 bytes Memory Device Array Handle: 0x0018 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 1024 MB Form Factor: DIMM Set: None Locator: A3 Bank Locator: Bank6/7 Type: Unknown Type Detail: None Speed: 800 MHz (1.2 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x001D, DMI type 19, 15 bytes Memory Array Mapped Address Starting Address: 0x00000000000 Ending Address: 0x000FFFFFFFF Range Size: 4 GB Physical Array Handle: 0x0018 Partition Width: 32 Handle 0x001E, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00000000000 Ending Address: 0x0003FFFFFFF Range Size: 1 GB Physical Device Handle: 0x0019 Memory Array Mapped Address Handle: 0x001D Partition Row Position: 1 Handle 0x001F, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00040000000 Ending Address: 0x0007FFFFFFF Range Size: 1 GB Physical Device Handle: 0x001A Memory Array Mapped Address Handle: 0x001D Partition Row Position: 1 Handle 0x0020, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00080000000 Ending Address: 0x000BFFFFFFF Range Size: 1 GB Physical Device Handle: 0x001B Memory Array Mapped Address Handle: 0x001D Partition Row Position: 1 Handle 0x0021, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x000C0000000 Ending Address: 0x000FFFFFFFF Range Size: 1 GB Physical Device Handle: 0x001C Memory Array Mapped Address Handle: 0x001D Partition Row Position: 1 Handle 0x0022, DMI type 32, 11 bytes System Boot Information Status: No errors detected Handle 0x0023, DMI type 64, 49 bytes Unknown Type Header and Data: 40 31 23 00 00 1F D0 A0 CB 61 FF FF B9 00 1F D0 A0 CB 63 FF FF BB 00 1F D0 A0 CB 71 FF FF C9 00 1F D0 A0 CB 73 FF FF CB 00 1F D0 00 00 2F 7E C5 61 Strings: Handle 0x0024, DMI type 127, 4 bytes End Of Table
