I've been experiencing some odd behavior with 2.6.26 and 2.6.28 on a Debian Lenny system with two SATA drives, its as if the kernel initially sees the partitions on the second device, but then forgets about them later. On boot, the kernel sees the partition tables for /dev/sdb, a SATA WDC WD5000YS drive, I can tell because I see in the dmesg the device and its parititions: [ 34.375757] sdb: sdb1 sdb2 sdb3 Also, if I debug the initramfs, I can see the partitions exist: (initramfs) ls -l /dev/[hs]d* brw-rw---- 1 0 0 22, 0 Mar 17 21:13 /dev/hdc brw-rw---- 1 0 0 8, 0 Mar 17 21:13 /dev/sda brw-rw---- 1 0 0 8, 1 Mar 17 21:13 /dev/sda1 brw-rw---- 1 0 0 8, 2 Mar 17 21:13 /dev/sda2 brw-rw---- 1 0 0 8, 3 Mar 17 21:13 /dev/sda3 brw-rw---- 1 0 0 8, 16 Mar 17 21:13 /dev/sdb brw-rw---- 1 0 0 8, 17 Mar 17 21:13 /dev/sdb1 brw-rw---- 1 0 0 8, 18 Mar 17 21:13 /dev/sdb2 brw-rw---- 1 0 0 8, 19 Mar 17 21:13 /dev/sdb3 However, once the system is fully up, the partitions do not exist in /dev/sdb* (although /dev/sdb exists): brw-rw---- 1 root disk 8, 16 2009-03-17 15:10 /dev/sdb One feels the urge to blame udev, but udev relies on what is in /sys, and /sys/block/sdb doesn't contain any partitions: bdi capability dev device ext_range holders power queue range removable ro size slaves stat subsystem uevent compare with /sys/block/sda: bdi dev ext_range power range ro sda2 size stat uevent capability device holders queue removable sda1 sda3 slaves subsystem No files, no events for udev to trigger on. Additionally, /proc/partitions doesn't show any partitions for /dev/sdb: # cat /proc/partitions major minor #blocks name 8 0 488386584 sda 8 1 489951 sda1 8 2 979965 sda2 8 3 486914085 sda3 8 16 488386584 sdb 9 0 489856 md0 9 1 486913984 md1 253 0 486912956 dm-0 253 1 1048576 dm-1 253 2 5242880 dm-2 253 3 5242880 dm-3 253 4 475377664 dm-4 253 5 979965 dm-5 Oddly, I can open up the partition table with fdisk/cfdisk and I can see that /dev/sdb has valid partitions: Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 61 489951 fd Linux raid autodetect /dev/sdb2 62 183 979965 83 Linux /dev/sdb3 184 60801 486914085 fd Linux raid autodetect Even more strange is that if I run: blockdev --rereadpt /dev/sdb suddenly they show up again! On the console I see: [ 866.514569] sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB) [ 866.517793] sd 2:0:0:0: [sdb] Write Protect is off [ 866.521806] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 866.530926] sdb: sdb1 sdb2 sdb3 and udev triggers and /dev/sdb* exist now: brw-rw---- 1 root disk 8, 16 2009-03-17 15:10 /dev/sdb brw-rw---- 1 root disk 8, 17 2009-03-17 15:24 /dev/sdb1 brw-rw---- 1 root disk 8, 18 2009-03-17 15:24 /dev/sdb2 brw-rw---- 1 root disk 8, 19 2009-03-17 15:24 /dev/sdb3 This is the complete dmesg output: root (hd0,0) Filesystem type is ext2fs, partition type 0xfd kernel /vmlinuz-2.6.26-1-686 root=/dev/mapper/vg_shoveler0-root ro console=tty 0 console=ttyS0,115200n8 [Linux-bzImage, setup=0x3000, size=0x16c890] initrd /initrd.img-2.6.26-1-686 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-13) (waldi@xxxxxxxxxx) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Sat Jan 10 18:29:31 UTC 2009 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000f7ef9000 (usable) [ 0.000000] BIOS-e820: 00000000f7ef9000 - 00000000f7f00000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000f7f00000 - 00000000f7f80000 (usable) [ 0.000000] BIOS-e820: 00000000f7f80000 - 00000000f8000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved) [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000404000000 (usable) [ 0.000000] Warning only 4GB will be used. [ 0.000000] Use a HIGHMEM64G enabled kernel. [ 0.000000] 3200MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at [c00f6330] 000f6330 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 1048576 [ 0.000000] DMI present. [ 0.000000] ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080321] [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] Virtual Wire compatibility mode. [ 0.000000] MPTABLE: OEM ID: Product ID: Kings Canyon <6>MPTABLE: Product ID: Kings Canyon <6>MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] Processor #6 [ 0.000000] Processor #1 [ 0.000000] Processor #7 [ 0.000000] I/O APIC #2 Version 32 at 0xFEC00000. [ 0.000000] I/O APIC #3 Version 32 at 0xFEC80000. [ 0.000000] I/O APIC #4 Version 32 at 0xFEC80400. [ 0.000000] I/O APIC #5 Version 32 at 0xFEC81000. [ 0.000000] I/O APIC #8 Version 32 at 0xFEC81400. [ 0.000000] Enabling APIC mode: Flat. Using 5 I/O APICs [ 0.000000] Processors: 4 [ 0.000000] Allocating PCI resources starting at f8800000 (gap: f8000000:06c00000) [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000 [ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000 [ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384 [ 0.000000] Kernel command line: root=/dev/mapper/vg_shoveler0-root ro console=tty0 console=ttyS0,115200n8 [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 3189.489 MHz processor. [ 0.004000] Console: colour VGA+ 80x25 [ 0.004000] console [tty0] enabled [ 0.004000] console [ttyS0] enabled [ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.004000] Memory: 4017032k/4194304k available (1769k kernel code, 44444k reserved, 752k data, 244k init, 3145188k highmem) [ 0.004000] virtual kernel memory layout: [ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB) [ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB) [ 0.004000] .data : 0xc02ba4ab - 0xc0376620 ( 752 kB) [ 0.004000] .text : 0xc0100000 - 0xc02ba4ab (1769 kB) [ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.084173] Calibrating delay using timer specific routine.. 6385.02 BogoMIPS (lpj=12770043) [ 0.092770] Security Framework initialized [ 0.096929] SELinux: Disabled at boot. [ 0.100821] Capability LSM initialized [ 0.104640] Mount-cache hash table entries: 512 [ 0.109426] Initializing cgroup subsys ns [ 0.113497] Initializing cgroup subsys cpuacct [ 0.117999] Initializing cgroup subsys devices [ 0.122517] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 0.127767] CPU: L2 cache: 512K [ 0.130964] CPU: L3 cache: 1024K [ 0.134249] CPU: Physical Processor ID: 0 [ 0.138313] Intel machine check architecture supported. [ 0.143590] Intel machine check reporting enabled on CPU#0. [ 0.148009] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available [ 0.152009] CPU0: Thermal monitoring enabled [ 0.156009] Checking 'hlt' instruction... OK. [ 0.174377] ACPI: Core revision 20080321 [ 0.178393] ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20080321] [ 0.188754] ACPI: Unable to load the System Description Tables [ 0.195131] ExtINT not setup in hardware but reported by MP table [ 0.200012] ENABLING IO-APIC IRQs [ 0.203606] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0 [ 0.247725] CPU0: Intel(R) Xeon(TM) CPU 3.20GHz stepping 05 [ 0.364022] Booting processor 1/6 ip 6000 [ 0.376023] Initializing CPU#1 [ 0.376023] Calibrating delay using timer specific routine.. 6379.17 BogoMIPS (lpj=12758343) [ 0.376023] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 0.376023] CPU: L2 cache: 512K [ 0.376023] CPU: L3 cache: 1024K [ 0.376023] CPU: Physical Processor ID: 3 [ 0.376023] Intel machine check architecture supported. [ 0.376023] Intel machine check reporting enabled on CPU#1. [ 0.376023] CPU1: Intel P4/Xeon Extended MCE MSRs (12) available [ 0.376023] CPU1: Thermal monitoring enabled [ 0.456028] CPU1: Intel(R) Xeon(TM) CPU 3.20GHz stepping 05 [ 0.463891] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 0.468029] Booting processor 2/1 ip 6000 [ 0.484030] Initializing CPU#2 [ 0.484030] Calibrating delay using timer specific routine.. 6379.13 BogoMIPS (lpj=12758277) [ 0.484030] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 0.484030] CPU: L2 cache: 512K [ 0.484030] CPU: L3 cache: 1024K [ 0.484030] CPU: Physical Processor ID: 0 [ 0.484030] Intel machine check architecture supported. [ 0.484030] Intel machine check reporting enabled on CPU#2. [ 0.484030] CPU2: Intel P4/Xeon Extended MCE MSRs (12) available [ 0.484030] CPU2: Thermal monitoring enabled [ 0.561948] CPU2: Intel(R) Xeon(TM) CPU 3.20GHz stepping 05 [ 0.572032] checking TSC synchronization [CPU#0 -> CPU#2]: passed. [ 0.576148] Booting processor 3/7 ip 6000 [ 0.592027] Initializing CPU#3 [ 0.592027] Calibrating delay using timer specific routine.. 6379.17 BogoMIPS (lpj=12758342) [ 0.592027] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 0.592027] CPU: L2 cache: 512K [ 0.592027] CPU: L3 cache: 1024K [ 0.592027] CPU: Physical Processor ID: 3 [ 0.592027] Intel machine check architecture supported. [ 0.592027] Intel machine check reporting enabled on CPU#3. [ 0.592027] CPU3: Intel P4/Xeon Extended MCE MSRs (12) available [ 0.592027] CPU3: Thermal monitoring enabled [ 0.672411] CPU3: Intel(R) Xeon(TM) CPU 3.20GHz stepping 05 [ 0.681559] checking TSC synchronization [CPU#0 -> CPU#3]: passed. [ 0.685559] Brought up 4 CPUs [ 0.688581] Total of 4 processors activated (25522.50 BogoMIPS). [ 0.693559] net_namespace: 660 bytes [ 0.697193] Booting paravirtualized kernel on bare hardware [ 0.701559] NET: Registered protocol family 16 [ 0.705559] PCI: PCI BIOS revision 2.10 entry at 0xfd875, last bus=7 [ 0.710082] PCI: Using configuration type 1 for base access [ 0.714082] Setting up standard PCI resources [ 0.746082] ACPI: Interpreter disabled. [ 0.749978] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.754082] pnp: PnP ACPI: disabled [ 0.758086] PnPBIOS: Scanning system for PnP BIOS support... [ 0.762540] PnPBIOS: Found PnP BIOS installation structure at 0xc00f63c0 [ 0.770070] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x8ebc, dseg 0x400 [ 0.781811] PnPBIOS: 21 nodes reported by PnP BIOS; 21 recorded by driver [ 0.785812] PCI: Probing PCI hardware [ 0.789811] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO [ 0.793812] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4 GPIO [ 0.797812] PCI: Transparent bridge - 0000:00:1e.0 [ 0.801812] PCI: Discovered primary peer bus 10 [IRQ] [ 0.807657] PCI: Discovered primary peer bus 11 [IRQ] [ 0.811657] PCI: Discovered primary peer bus 12 [IRQ] [ 0.817802] PCI: Using IRQ router PIIX/ICH [8086/2480] at 0000:00:1f.0 [ 0.821802] PCI->APIC IRQ transform: 0000:00:1d.0[A] -> IRQ 16 [ 0.825802] PCI->APIC IRQ transform: 0000:00:1d.1[B] -> IRQ 19 [ 0.829802] PCI->APIC IRQ transform: 0000:00:1d.2[C] -> IRQ 18 [ 0.833802] PCI->APIC IRQ transform: 0000:03:01.0[A] -> IRQ 24 [ 0.837802] PCI->APIC IRQ transform: 0000:03:02.0[A] -> IRQ 28 [ 0.841802] PCI->APIC IRQ transform: 0000:03:02.1[B] -> IRQ 29 [ 0.845802] PCI->APIC IRQ transform: 0000:06:02.0[A] -> IRQ 76 [ 0.849802] PCI->APIC IRQ transform: 0000:06:02.1[B] -> IRQ 77 [ 0.853802] PCI->APIC IRQ transform: 0000:07:01.0[A] -> IRQ 16 [ 0.865803] system 00:00: iomem range 0xfff00000-0xffffffff could not be reserved [ 0.873431] system 00:00: iomem range 0xfebffc00-0xfebfffff has been reserved [ 0.881437] system 00:01: iomem range 0x0-0x9ffff could not be reserved [ 0.888854] system 00:01: iomem range 0xe4000-0xfffff could not be reserved [ 0.895872] system 00:09: iomem range 0xe0000-0xe3fff has been reserved [ 0.902541] system 00:0b: ioport range 0x4d0-0x4d1 has been reserved [ 0.909217] system 00:0b: ioport range 0x1000-0x105f has been reserved [ 0.915788] system 00:0b: ioport range 0x1060-0x107f has been reserved [ 0.922202] system 00:0b: ioport range 0x1180-0x11bf has been reserved [ 0.928791] system 00:0e: iomem range 0xfec00000-0xfec0ffff could not be reserved [ 0.936329] system 00:0e: iomem range 0xfee00000-0xfee00fff could not be reserved [ 0.943867] system 00:0f: iomem range 0xd1800-0xd3fff could not be reserved [ 0.956176] PCI: Bridge: 0000:01:1d.0 [ 0.957463] IO window: disabled. [ 0.960181] MEM window: disabled. [ 0.964179] PREFETCH window: disabled. [ 0.968180] PCI: Bridge: 0000:01:1f.0 [ 0.972176] IO window: 3000-3fff [ 0.976176] MEM window: 0xfc200000-0xfc7fffff [ 0.980762] PREFETCH window: disabled. [ 0.984737] PCI: Bridge: 0000:00:02.0 [ 0.988449] IO window: 3000-3fff [ 0.992173] MEM window: 0xfc100000-0xfc7fffff [ 0.996759] PREFETCH window: disabled. [ 1.000736] PCI: Bridge: 0000:04:1d.0 [ 1.004444] IO window: disabled. [ 1.008174] MEM window: disabled. [ 1.011718] PREFETCH window: disabled. [ 1.015697] PCI: Bridge: 0000:04:1f.0 [ 1.019403] IO window: 4000-4fff [ 1.022859] MEM window: 0xfc900000-0xfc9fffff [ 1.027440] PREFETCH window: 0x00000000f8800000-0x00000000f88fffff [ 1.033845] PCI: Bridge: 0000:00:03.0 [ 1.037555] IO window: 4000-4fff [ 1.041015] MEM window: 0xfc800000-0xfc9fffff [ 1.045599] PREFETCH window: 0x00000000f8800000-0x00000000f88fffff [ 1.053060] PCI: Bridge: 0000:00:1e.0 [ 1.056769] IO window: 5000-5fff [ 1.060227] MEM window: 0xfca00000-0xfdffffff [ 1.063219] PREFETCH window: 0x00000000f8900000-0x00000000f89fffff [ 1.069718] NET: Registered protocol family 2 [ 1.090206] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 1.097757] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 1.106011] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 1.113643] TCP: Hash tables configured (established 131072 bind 65536) [ 1.118129] TCP reno registered [ 1.129461] NET: Registered protocol family 1 [ 1.134270] checking if image is initramfs... it is [ 1.696156] Freeing initrd memory: 7404k freed [ 1.703731] audit: initializing netlink socket (disabled) [ 1.707759] type=2000 audit(1237322534.682:1): initialized [ 1.716156] highmem bounce pool size: 64 pages [ 1.720162] Total HugeTLB memory allocated, 0 [ 1.725470] VFS: Disk quotas dquot_6.5.1 [ 1.729483] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.733722] msgmni has been set to 1718 [ 1.740225] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.745472] io scheduler noop registered [ 1.749472] io scheduler anticipatory registered [ 1.754142] io scheduler deadline registered [ 1.758482] io scheduler cfq registered (default) [ 1.767817] isapnp: Scanning for PnP cards... [ 2.128128] isapnp: No Plug & Play device found [ 2.138797] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 2.148319] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.154508] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.160694] 00:11: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.167191] 00:12: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.174897] brd: module loaded [ 2.180023] PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12 [ 2.187694] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.192719] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.200967] mice: PS/2 mouse device common for all mice [ 2.209263] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 [ 2.215424] rtc0: alarms up to one day [ 2.219382] cpuidle: using governor ladder [ 2.223385] cpuidle: using governor menu [ 2.227364] No iBFT detected. [ 2.231221] TCP cubic registered [ 2.234499] NET: Registered protocol family 17 [ 2.239498] Using IPI No-Shortcut mode [ 2.247302] registered taskstats version 1 [ 2.251486] rtc_cmos 00:05: setting system clock to 2009-03-17 20:42:16 UTC (1237322536) [ 2.259806] Freeing unused kernel memory: 244k freed Loading, please wait... Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... FATAL: Error inserting fan (/lib/modules/2.6.26-1-686/kernel/drivers/acpi/fan.ko): No such device WARNING: Error i[ 2.384460] thermal: Unknown symbol acpi_processor_set_thermal_limit nserting processor (/lib/modules/2.6.26-1-686/kernel/drivers/acpi/processor.ko): No such device FATAL: Error inserting thermal (/lib/modules/2.6.26-1-686/kernel/drivers/acpi/thermal.ko): Unknown symbol in module, or unknown parameter (see dmesg) [ 2.595390] usbcore: registered new interface driver usbfs [ 2.600139] usbcore: registered new interface driver hub [ 2.608131] usbcore: registered new device driver usb [ 2.616130] SCSI subsystem initialized [ 2.635255] USB Universal Host Controller Interface driver v3.0 [ 2.643228] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.649604] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 2.655072] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00002000 [ 2.661564] usb usb1: configuration #1 chosen from 1 choice [ 2.669099] hub 1-0:1.0: USB hub found [ 2.672978] hub 1-0:1.0: 2 ports detected [ 2.694969] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 2.701614] Copyright (c) 1999-2006 Intel Corporation. [ 2.732435] Floppy drive(s): fd0 is 1.44M [ 2.754112] FDC 0 is a post-1991 82077 [ 2.793348] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.798126] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.808773] usb usb1: Product: UHCI Host Controller [ 2.813753] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd [ 2.819776] usb usb1: SerialNumber: 0000:00:1d.0 [ 2.827774] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.832512] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 2.841394] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002020 [ 2.849461] usb usb2: configuration #1 chosen from 1 choice [ 2.855194] hub 2-0:1.0: USB hub found [ 2.859161] hub 2-0:1.0: 2 ports detected [ 2.967244] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.973920] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.980961] usb usb2: Product: UHCI Host Controller [ 2.988318] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd [ 2.993284] usb usb2: SerialNumber: 0000:00:1d.1 [ 3.000315] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 3.005708] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 3.015910] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 [ 3.021902] usb usb3: configuration #1 chosen from 1 choice [ 3.027731] hub 3-0:1.0: USB hub found [ 3.031707] hub 3-0:1.0: 2 ports detected [ 3.050009] usb 1-1: new low speed USB device using uhci_hcd and address 2 [ 3.142951] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.149897] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.159020] usb usb3: Product: UHCI Host Controller [ 3.164022] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd [ 3.170068] usb usb3: SerialNumber: 0000:00:1d.2 [ 3.246118] usb 1-1: configuration #1 chosen from 1 choice [ 3.459637] e1000: 0000:03:02.0: e1000_probe: (PCI-X:133MHz:64-bit) 00:30:48:2d:07:3a [ 3.464467] usb 1-1: New USB device found, idVendor=0624, idProduct=0341 [ 3.471681] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.479659] usb 1-1: Product: HP 336047-B21 [ 3.484547] usb 1-1: Manufacturer: Avocent [ 3.495265] usbcore: registered new interface driver hiddev [ 3.515257] input: Avocent HP 336047-B21 as /class/input/input0 [ 3.516687] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [ 3.542769] input,hidraw0: USB HID v1.10 Keyboard [Avocent HP 336047-B21] on usb-0000:00:1d.0-1 [ 3.570737] input: Avocent HP 336047-B21 as /class/input/input1 [ 3.810741] e1000: 0000:03:02.1: e1000_probe: (PCI-X:133MHz:64-bit) 00:30:48:2d:07:3b [ 3.823924] input,hidraw1: USB HID v1.10 Mouse [Avocent HP 336047-B21] on usb-0000:00:1d.0-1 [ 3.829324] usbcore: registered new interface driver usbhid [ 3.837313] usbhid: v2.6:USB HID core driver [ 3.862257] e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection [ 3.885736] sata_mv 0000:03:01.0: version 1.24 [ 3.890508] sata_mv 0000:03:01.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx [ 3.902011] scsi0 : sata_mv [ 3.905326] scsi1 : sata_mv [ 3.909939] scsi2 : sata_mv [ 3.909939] scsi3 : sata_mv [ 3.917251] scsi4 : sata_mv [ 3.920300] scsi5 : sata_mv [ 3.923342] scsi6 : sata_mv [ 3.923342] scsi7 : sata_mv [ 3.927381] ata1: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc222000 irq 24 [ 3.935344] ata2: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc224000 irq 24 [ 3.943345] ata3: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc226000 irq 24 [ 3.951344] ata4: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc228000 irq 24 [ 3.959344] ata5: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc232000 irq 24 [ 3.967344] ata6: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc234000 irq 24 [ 3.975344] ata7: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc236000 irq 24 [ 3.983342] ata8: SATA max UDMA/133 mmio m1048576@0xfc200000 port 0xfc238000 irq 24 [ 4.467422] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.503642] ata1.00: ATA-8: WDC WD5002ABYS-01B1B0, 02.03B02, max UDMA/133 [ 4.511595] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 4.519603] ata1.00: max_sectors limited to 256 for NCQ [ 4.547241] ata1.00: max_sectors limited to 256 for NCQ [ 4.551748] ata1.00: configured for UDMA/133 [ 5.031650] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.069430] ata2.00: ATA-7: WDC WD5000YS-01MPB1, 09.02E09, max UDMA/133 [ 5.073434] ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 5.080273] ata2.00: max_sectors limited to 256 for NCQ [ 5.111746] ata2.00: max_sectors limited to 256 for NCQ [ 5.116074] ata2.00: configured for UDMA/133 [ 5.439140] ata3: SATA link down (SStatus 0 SControl 300) [ 5.764452] ata4: SATA link down (SStatus 0 SControl 300) [ 6.089202] ata5: SATA link down (SStatus 0 SControl 300) [ 6.413260] ata6: SATA link down (SStatus 0 SControl 300) [ 6.737318] ata7: SATA link down (SStatus 0 SControl 300) [ 7.060647] ata8: SATA link down (SStatus 0 SControl 300) [ 7.068439] scsi 0:0:0:0: Direct-Access ATA WDC WD5002ABYS-0 02.0 PQ: 0 ANSI: 5 [ 7.076597] scsi 1:0:0:0: Direct-Access ATA WDC WD5000YS-01M 09.0 PQ: 0 ANSI: 5 [ 19.019773] scsi8 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 19.019776] <Adaptec AIC7902 Ultra320 SCSI adapter> [ 19.019778] aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs [ 34.163649] scsi9 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 34.163652] <Adaptec AIC7902 Ultra320 SCSI adapter> [ 34.163653] aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs [ 34.202685] Uniform Multi-Platform E-IDE driver [ 34.204182] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 34.221183] ICH3: IDE controller (0x8086:0x248b rev 0x02) at PCI slot 0000:00:1f.1 [ 34.229208] ICH3: not 100% native mode: will probe irqs later [ 34.235228] ide0: BM-DMA at 0x2060-0x2067 [ 34.242726] ide1: BM-DMA at 0x2068-0x206f [ 34.255769] Driver 'sd' needs updating - please use bus_type methods [ 34.260403] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) [ 34.271258] sd 0:0:0:0: [sda] Write Protect is off [ 34.278648] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 34.288602] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) [ 34.296556] sd 0:0:0:0: [sda] Write Protect is off [ 34.303902] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 34.310041] sda: sda1 sda2 sda3 [ 34.324592] sd 0:0:0:0: [sda] Attached SCSI disk [ 34.328662] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 34.336111] sd 1:0:0:0: [sdb] Write Protect is off [ 34.344592] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 34.357052] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 34.364309] sd 1:0:0:0: [sdb] Write Protect is off [ 34.370429] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 34.375757] sdb: sdb1 sdb2 sdb3 [ 34.390429] sd 1:0:0:0: [sdb] Attached SCSI disk [ 35.601071] hdc: CD-224E, ATAPI CD/DVD-ROM drive [ 36.277324] hdc: UDMA/33 mode selected [ 36.282605] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 36.286878] ide1 at 0x170-0x177,0x376 on irq 15 [ 36.312299] hdc: ATAPI 24X CD-ROM drive, 128kB Cache [ 36.317578] Uniform CD-ROM driver Revision: 3.20 done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... Begin: Loading[ 36.401305] md: raid1 personality registered for level 1 Success: loaded module raid1. done. Begin: Assembling all MD arrays ... [ 36.417883] md: md0 stopped. [ 36.499256] md: could not open unknown-block(8,17). [ 36.503264] md: md_import_device returned -6 mdadm: failed to[ 36.507819] md: bind<sda1> add /dev/sdb1 to /dev/md0: No such device or address [ 36.524325] raid1: raid set md0 active with 1 out of 2 mirrors mdadm: /dev/md0 [ 36.530810] md: md1 stopped. has been started with 1 drive (out of 2). [ 36.543977] md: bind<sda3> [ 36.559183] raid1: raid set md1 active with 1 out of 2 mirrors mdadm: /dev/md1 has been started with 1 drive (out of 2). Success: assembled all arrays. done. Begin: Waiting for udev to process events ... done. [ 36.635782] device-mapper: uevent: version 1.0.3 [ 36.639775] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx Volume group "vg_shoveler0" not found Enter passphrase to unlock the disk /dev/md1 (md1_crypt): key slot 0 unlocked. Command successful. File descriptor 3 left open 4 logical volume(s) in volume group "vg_shoveler0" now active cryptsetup: md1_crypt setup successfully done. Begin: Running /scripts/local-premount ... done. [ 41.119869] kjournald starting. Commit interval 5 seconds Begin: Running /[ 41.119869] EXT3-fs: mounted filesystem with ordered data mode. scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.86 booting Starting the hotplug events dispatcher: udevd[ 42.134635] udevd version 125 started . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...[ 42.670909] EDAC MC: Ver: 2.1.0 Jan 10 2009 [ 42.686611] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 42.706153] input: PC Speaker as /class/input/input2 [ 42.743895] EDAC e7xxx: tolm = f8000, remapbase = 3fc000, remaplimit = 404000 [ 42.754953] EDAC MC0: Giving out device to 'e7xxx_edac' 'E7501': DEV 0000:00:00.0 [ 42.758991] EDAC PCI0: Giving out device to module 'e7xxx_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED) [ 42.784928] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 42.878770] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) [ 42.887797] iTCO_wdt: Found a ICH3-S TCO device (Version=1, TCOBASE=0x1060) [ 42.895736] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 43.002068] PCI: No IRQ known for interrupt pin B of device 0000:00:1f.3. Probably buggy MP table. [ 43.129537] Intel 82802 RNG detected [ 43.205068] parport_pc 00:15: reported by Plug and Play BIOS [ 43.212367] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP] [ 43.251994] Error: Driver 'pcspkr' is already registered, aborting... done. Setting the system clock. Checking root file system...fsck 1.41.3 (12-Oct-2008) /dev/mapper/vg_shoveler0-root: clean, 12115/65536 files, 77966/262144 blocks done. [ 43.970669] EXT3 FS on dm-1, internal journal Setting the system clock. Cleaning up ifupdown.... Loading kernel modules...[ 44.203508] loop: module loaded done. Generating udev events for MD arrays...done. Starting early crypto disks...sda2_crypt (starting). done. Setting up LVM Volume Groups Reading all physical volumes. This may take a while... Found volume group "vg_shoveler0" using metadata type lvm2 4 logical volume(s) in volume group "vg_shoveler0" now active . Starting remaining crypto disks...done. Checking file systems...fsck 1.41.3 (12-Oct-2008) /dev/md0: clean, 47/122880 files, 97056/489856 blocks /dev/mapper/vg_shoveler0-usr: clean, 19614/327680 files, 141986/1310720 blocks /dev/mapper/vg_shoveler0-var: clean, 2404/327680 files, 162666/1310720 blocks done. Setting kernel variables (/etc/sysctl.conf)...done. Mounting local filesystems...[ 46.987408] kjournald starting. Commit interval 5 seconds [ 47.053398] EXT3 FS on md0, internal journal [ 47.057403] EXT3-fs: mounted filesystem with ordered data mode. [ 47.109475] kjournald starting. Commit interval 5 seconds [ 47.109475] EXT3 FS on dm-2, internal journal [ 47.109475] EXT3-fs: mounted filesystem with ordered data mode. [ 47.152371] kjournald starting. Commit interval 5 seconds done. [ 47.152575] EXT3 FS on dm-3, internal journal [ 47.152580] EXT3-fs: mounted filesystem with ordered data mode. Activating swapfile swap...[ 47.497038] Adding 979956k swap on /dev/mapper/sda2_crypt. Priority:-1 extents:1 across:979956k done. Setting up networking.... Configuring network interfaces...[ 48.905311] NET: Registered protocol family 10 [ 48.909308] lo: Disabled Privacy Extensions [ 48.984339] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 48.985275] e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX [ 49.000331] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready if-up.d/mountnfs[eth0]: waiting for interface eth1 before doing NFS mounts (warning). [ 49.101671] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 49.104158] e1000: eth1: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX [ 49.115883] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready done. Setting console screen modes and fonts. INIT: Entering runlevel: 2 Starting enhanced syslogd: rsyslogd. Starting system message bus: dbus. Starting domain name service...: bind9. Starting virtual private network daemon: phoenix. Starting OpenBSD Secure Shell server: sshd. Starting MTA: exim4. Starting nagios-statd-server: nagios-statd. Starting puppet configuration management tool[ 57.307052] tun: Universal TUN/TAP device driver, 1.6 [ 57.311052] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> [ 57.324824] tun0: Disabled Privacy Extensions . Starting NTP server: ntpd. Starting MD monitoring service: mdadm --monitor . Starting periodic command scheduler: crond. Starting Munin-Node: done. [ 65.159188] warning: `ntpd' uses 32-bit capabilities (legacy support in use) output from scripts/ver_linux: Linux shoveler 2.6.28-1-686-bigmem #1 SMP Mon Feb 23 04:05:37 UTC 2009 i686 GNU/Linux Gnu C ./ver_linux: Gnu make 3.81 binutils 2.18.0.20080103 util-linux 2.13.1.1 mount 2.13.1.1 module-init-tools 3.4 e2fsprogs 1.41.3 Linux C Library 2.7 Dynamic linker (ldd) 2.7 Procps 3.2.7 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 6.10 udev 125 Modules Loaded tun ipv6 loop parport_pc parport psmouse serio_raw pcspkr intel_rng rng_core i2c_i801 i2c_core iTCO_wdt evdev joydev shpchp pci_hotplug e7xxx_edac edac_core ext3 jbd mbcache serpent xts gf128mul dm_crypt dm_mirror dm_region_hash dm_log dm_snapshot dm_mod raid1 md_mod sd_mod crc_t10dif ide_cd_mod cdrom ide_pci_generic usbhid hid piix ide_core ata_generic sata_mv floppy aic79xx scsi_transport_spi uhci_hcd libata e1000 scsi_mod usbcore thermal_sys -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html