Various cosmetic changes in preparation for the IRQ coalescing feature.
Note that the various MV_IRQ_COAL_* definitions are restored/renamed
in the folloup patch which adds IRQ coalescing to the driver.
Signed-off-by: Mark Lord <mlord@xxxxxxxxx>
---
This is for libata-dev #upstream
--- old/drivers/ata/sata_mv.c 2009-03-10 18:20:20.000000000 -0400
+++ new/drivers/ata/sata_mv.c 2009-03-10 18:26:54.000000000 -0400
@@ -1,10 +1,13 @@
/*
* sata_mv.c - Marvell SATA support
*
- * Copyright 2008: Marvell Corporation, all rights reserved.
+ * Copyright 2008-2009: Marvell Corporation, all rights reserved.
* Copyright 2005: EMC Corporation, all rights reserved.
* Copyright 2005 Red Hat, Inc. All rights reserved.
*
+ * Originally written by Brett Russ.
+ * Extensive overhaul and enhancement by Mark Lord <mlord@xxxxxxxxx>.
+ *
* Please ALWAYS copy linux-ide@xxxxxxxxxxxxxxx on emails.
*
* This program is free software; you can redistribute it and/or modify
@@ -25,8 +28,6 @@
/*
* sata_mv TODO list:
*
- * --> Errata workaround for NCQ device errors.
- *
* --> More errata workarounds for PCI-X.
*
* --> Complete a full errata audit for all chipsets to identify others.
@@ -68,6 +69,16 @@
#define DRV_NAME "sata_mv"
#define DRV_VERSION "1.26"
+/*
+ * module options
+ */
+
+static int msi;
+#ifdef CONFIG_PCI
+module_param(msi, int, S_IRUGO);
+MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)");
+#endif
+
enum {
/* BAR's are enumerated in terms of pci_resource_start() terms */
MV_PRIMARY_BAR = 0, /* offset 0x10: memory space */
@@ -78,12 +89,6 @@
MV_MINOR_REG_AREA_SZ = 0x2000, /* 8KB */
MV_PCI_REG_BASE = 0,
- MV_IRQ_COAL_REG_BASE = 0x18000, /* 6xxx part only */
- MV_IRQ_COAL_CAUSE = (MV_IRQ_COAL_REG_BASE + 0x08),
- MV_IRQ_COAL_CAUSE_LO = (MV_IRQ_COAL_REG_BASE + 0x88),
- MV_IRQ_COAL_CAUSE_HI = (MV_IRQ_COAL_REG_BASE + 0x8c),
- MV_IRQ_COAL_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xcc),
- MV_IRQ_COAL_TIME_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xd0),
MV_SATAHC0_REG_BASE = 0x20000,
MV_FLASH_CTL_OFS = 0x1046c,
@@ -115,16 +120,14 @@
/* Host Flags */
MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
- MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO | ATA_FLAG_PIO_POLLING,
MV_GEN_I_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NO_ATAPI,
- MV_GEN_II_FLAGS = MV_COMMON_FLAGS | MV_FLAG_IRQ_COALESCE |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ,
+ MV_GEN_II_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NCQ |
+ ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA,
MV_GEN_IIE_FLAGS = MV_GEN_II_FLAGS | ATA_FLAG_AN,
@@ -179,16 +182,16 @@
PCI_HC_MAIN_IRQ_MASK_OFS = 0x1d64,
SOC_HC_MAIN_IRQ_CAUSE_OFS = 0x20020,
SOC_HC_MAIN_IRQ_MASK_OFS = 0x20024,
- ERR_IRQ = (1 << 0), /* shift by port # */
- DONE_IRQ = (1 << 1), /* shift by port # */
+ ERR_IRQ = (1 << 0), /* shift by (2 * port #) */
+ DONE_IRQ = (1 << 1), /* shift by (2 * port #) */
HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */
HC_SHIFT = 9, /* bits 9-17 = HC1's ports */
PCI_ERR = (1 << 18),
- TRAN_LO_DONE = (1 << 19), /* 6xxx: IRQ coalescing */
- TRAN_HI_DONE = (1 << 20), /* 6xxx: IRQ coalescing */
- PORTS_0_3_COAL_DONE = (1 << 8),
- PORTS_4_7_COAL_DONE = (1 << 17),
- PORTS_0_7_COAL_DONE = (1 << 21), /* 6xxx: IRQ coalescing */
+ TRAN_COAL_LO_DONE = (1 << 19), /* transaction coalescing */
+ TRAN_COAL_HI_DONE = (1 << 20), /* transaction coalescing */
+ PORTS_0_3_COAL_DONE = (1 << 8), /* HC0 IRQ coalescing */
+ PORTS_4_7_COAL_DONE = (1 << 17), /* HC1 IRQ coalescing */
+ ALL_PORTS_COAL_DONE = (1 << 21), /* GEN_II(E) IRQ coalescing */
GPIO_INT = (1 << 22),
SELF_INT = (1 << 23),
TWSI_INT = (1 << 24),
@@ -621,7 +624,7 @@
.softreset = mv_softreset,
.error_handler = mv_pmp_error_handler,
- .sff_check_status = mv_sff_check_status,
+ .sff_check_status = mv_sff_check_status,
.sff_irq_clear = mv_sff_irq_clear,
.check_atapi_dma = mv_check_atapi_dma,
.bmdma_setup = mv_bmdma_setup,
@@ -1255,8 +1258,8 @@
}
/**
- * mv_bmdma_enable - set a magic bit on GEN_IIE to allow bmdma
- * @ap: Port being initialized
+ * mv_bmdma_enable - set a magic bit on GEN_IIE to allow bmdma
+ * @ap: Port being initialized
*
* There are two DMA modes on these chips: basic DMA, and EDMA.
*
@@ -2000,7 +2003,7 @@
struct mv_host_priv *hpriv = ap->host->private_data;
/*
* Workaround for 88SX60x1 FEr SATA#25 (part 2).
- *
+ *
* After any NCQ error, the READ_LOG_EXT command
* from libata-eh *must* use mv_qc_issue_fis().
* Otherwise it might fail, due to chip errata.
@@ -3704,12 +3707,6 @@
.remove = ata_pci_remove_one,
};
-/*
- * module options
- */
-static int msi; /* Use PCI msi; either zero (off, default) or non-zero */
-
-
/* move to PCI layer or libata core? */
static int pci_go_64(struct pci_dev *pdev)
{
@@ -3891,10 +3888,5 @@
MODULE_VERSION(DRV_VERSION);
MODULE_ALIAS("platform:" DRV_NAME);
-#ifdef CONFIG_PCI
-module_param(msi, int, 0444);
-MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)");
-#endif
-
module_init(mv_init);
module_exit(mv_exit);
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
