Hello, I've had a problem since 2.6.24.7-rt14 that has kept me from updating. I'm not sure when it started, that's to say this could have begun in 2.6.26 and I wouldn't know for sure, as I don't upgrade often on this computer. As far as I know, I can't bisect this problem as it refuses to allow me to unmount my large filesystem and I would like to prevent any problems as far as that goes. I'd like to make as few boots into this kernel as possible, and I need to know what is necessary to debug this problem or is this just a symptom of hardware going bad? If it's a symptom of hardware going bad, I guess this wasn't checked for in the 2.6.24.7-rt14 kernel? BTW- 2.6.24.7-rt14 kernel has been up 50 days at a time, with no instability, only coming down for upgrade attempts or moves. Thanks! Help! ;) http://avuton.googlepages.com/linux-2.6.24.7-rt14.config http://avuton.googlepages.com/linux-2.6.29-rc6-rt3.config before dmesg: Linux version 2.6.24.7-rt14 (root@shapeshifter) (gcc version 4.3.3 (Gentoo 4.3.3 p1.0, pie-10.1.5) ) #18 SMP PREEMPT RT Fri Feb 27 09:20:44 PST 2009 Command line: root=/dev/sdf3 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000beff0000 (usable) BIOS-e820: 00000000beff0000 - 00000000beff3000 (ACPI NVS) BIOS-e820: 00000000beff3000 - 00000000bf000000 (ACPI data) BIOS-e820: 00000000bf000000 - 00000000c0000000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 782320) 1 entries of 256 used end_pfn_map = 1048576 DMI 2.3 present. ACPI: RSDP 000F6BC0, 0014 (r0 GBT ) ACPI: RSDT BEFF3000, 0030 (r1 GBT AWRDACPI 42302E31 AWRD 1010101) ACPI: FACP BEFF3040, 0074 (r1 GBT AWRDACPI 42302E31 AWRD 1010101) ACPI: DSDT BEFF30C0, 4D2C (r1 GBT AWRDACPI 1000 MSFT 100000C) ACPI: FACS BEFF0000, 0040 ACPI: MCFG BEFF7E80, 003C (r1 GBT AWRDACPI 42302E31 AWRD 1010101) ACPI: APIC BEFF7E00, 0072 (r1 GBT AWRDACPI 42302E31 AWRD 1010101) Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 782320) 1 entries of 256 used [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0 [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0 [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0 [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0 [ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0 [ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0 [ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0 [ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002e00000 on node 0 [ffffe20001000000-ffffe200011fffff] PMD ->ffff810003200000 on node 0 [ffffe20001200000-ffffe200013fffff] PMD ->ffff810003600000 on node 0 [ffffe20001400000-ffffe200015fffff] PMD ->ffff810003a00000 on node 0 [ffffe20001600000-ffffe200017fffff] PMD ->ffff810003e00000 on node 0 [ffffe20001800000-ffffe200019fffff] PMD ->ffff810004200000 on node 0 [ffffe20001a00000-ffffe20001bfffff] PMD ->ffff810004600000 on node 0 [ffffe20001c00000-ffffe20001dfffff] PMD ->ffff810004a00000 on node 0 [ffffe20001e00000-ffffe20001ffffff] PMD ->ffff810004e00000 on node 0 [ffffe20002000000-ffffe200021fffff] PMD ->ffff810005200000 on node 0 [ffffe20002200000-ffffe200023fffff] PMD ->ffff810005600000 on node 0 [ffffe20002400000-ffffe200025fffff] PMD ->ffff810005a00000 on node 0 [ffffe20002600000-ffffe200027fffff] PMD ->ffff810005e00000 on node 0 [ffffe20002800000-ffffe200029fffff] PMD ->ffff810006200000 on node 0 Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0 -> 159 0: 256 -> 782320 On node 0 totalpages: 782223 DMA zone: 56 pages used for memmap DMA zone: 1866 pages reserved DMA zone: 2077 pages, LIFO batch:0 DMA32 zone: 10639 pages used for memmap DMA32 zone: 767585 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Movable zone: 0 pages used for memmap Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at c4000000 (gap: c0000000:30000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 31768 bytes of per cpu data Real-Time Preemption Support (C) 2004-2007 Ingo Molnar Built 1 zonelists in Zone order, mobility grouping on. Total pages: 769662 Kernel command line: root=/dev/sdf3 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) TSC calibrated against PM_TIMER Marking TSC unstable due to TSCs unsynchronized time.c: Detected 2210.053 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Checking aperture... CPU 0: aperture @ a20000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Memory: 3071152k/3129280k available (4694k kernel code, 57108k reserved, 1897k data, 248k init) Calibrating delay using timer specific routine.. 4424.99 BogoMIPS (lpj=7371185) Security Framework initialized Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20070126 Using local APIC timer interrupts. APIC timer calibration result 12557140 Detected 12.557 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 4421.33 BogoMIPS (lpj=7366943) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01 Brought up 2 CPUs CPU0 attaching sched-domain: domain 0: span 3 groups: 1 2 CPU1 attaching sched-domain: domain 0: span 3 groups: 2 1 net_namespace: 144 bytes NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: Using MMCONFIG at f0000000 - ffffffff ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:10.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMAC] (IRQs 5 *7 9 10 11 14 15) ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LAZA] (IRQs 5 *7 9 10 11 14 15) ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 5 *7 9 10 11 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0 ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0 ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0 ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0 ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0 ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0 Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 9 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report system 00:01: ioport range 0x1000-0x107f has been reserved system 00:01: ioport range 0x1080-0x10ff has been reserved system 00:01: ioport range 0x1400-0x147f has been reserved system 00:01: ioport range 0x1480-0x14ff has been reserved system 00:01: ioport range 0x1800-0x187f has been reserved system 00:01: ioport range 0x1880-0x18ff has been reserved system 00:01: ioport range 0x2000-0x207f has been reserved system 00:01: ioport range 0x2080-0x20ff has been reserved system 00:01: iomem range 0xfefe0000-0xfefe01ff has been reserved system 00:01: iomem range 0xbf000000-0xbfffffff could not be reserved system 00:01: iomem range 0xf0000000-0xf1ffffff could not be reserved system 00:02: ioport range 0x4d0-0x4d1 has been reserved system 00:02: ioport range 0x290-0x29f has been reserved system 00:08: iomem range 0xd3000-0xd3fff has been reserved system 00:08: iomem range 0xf0000-0xf7fff could not be reserved system 00:08: iomem range 0xf8000-0xfbfff could not be reserved system 00:08: iomem range 0xfc000-0xfffff could not be reserved system 00:08: iomem range 0xbeff0000-0xbeffffff could not be reserved system 00:08: iomem range 0xffff0000-0xffffffff has been reserved system 00:08: iomem range 0x0-0x9ffff could not be reserved system 00:08: iomem range 0x100000-0xbefeffff could not be reserved system 00:08: iomem range 0xbf000000-0xbfffffff could not be reserved system 00:08: iomem range 0xfec00000-0xfec00fff has been reserved system 00:08: iomem range 0xfee00000-0xfee00fff could not be reserved PCI: Bridge: 0000:00:03.0 IO window: 9000-afff MEM window: f7000000-f8ffffff PREFETCH window: c4000000-c40fffff PCI: Bridge: 0000:00:10.0 IO window: 8000-8fff MEM window: f3000000-f4ffffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:03.0 to 64 PCI: Setting latency timer of device 0000:00:10.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 10, 4194304 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered krcupreemptd setsched 0 prio = 98 RCU Preempt markers registered Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). fuse init (API version 7.9) SGI XFS with large block/inode numbers, no debug enabled io scheduler noop registered io scheduler cfq registered (default) Boot video device is 0000:00:05.0 PCI: Setting latency timer of device 0000:00:03.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:03.0:pcie00] Allocate Port Service[0000:00:03.0:pcie03] input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] lp: driver loaded but no devices found Real Time Clock Driver v1.12ac Linux agpgart interface v0.102 loop: module loaded forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:14.0 to 64 forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x3f1 @ 7, addr 00:14:85:35:ce:4d forcedeth 0000:00:14.0: highdma pwrctl timirq gbit lnktim desc-v3 r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16 eth1: RTL8110s at 0xffffc20000014000, 00:40:f4:a6:5c:ea, XID 04000000 IRQ 16 usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver rndis_host usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus Driver 'sd' needs updating - please use bus_type methods ahci 0000:02:00.0: version 3.0 ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16 ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 16 ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:02:00.0 to 64 scsi0 : ahci scsi1 : ahci ata1: SATA max UDMA/133 abar m8192@0xf8000000 port 0xf8000100 irq 16 ata2: SATA max UDMA/133 abar m8192@0xf8000000 port 0xf8000180 irq 16 ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-8: WDC WD10EACS-00ZJB0, 01.01B01, max UDMA/133 ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD10EACS-00Z 01.0 PQ: 0 ANSI: 5 sd 1:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: unknown partition table sd 1:0:0:0: [sda] Attached SCSI disk sd 1:0:0:0: Attached scsi generic sg0 type 0 sata_nv 0000:00:0e.0: version 3.5 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:0e.0 to 64 scsi2 : sata_nv scsi3 : sata_nv ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 22 ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 22 ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-7: Maxtor 3H500F0, HA431BV0, max UDMA/133 ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata3.00: configured for UDMA/133 ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: ATA-7: Maxtor 3H500F0, HA431BV0, max UDMA/133 ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata4.00: configured for UDMA/133 scsi 2:0:0:0: Direct-Access ATA Maxtor 3H500F0 HA43 PQ: 0 ANSI: 5 sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: unknown partition table sd 2:0:0:0: [sdb] Attached SCSI disk sd 2:0:0:0: Attached scsi generic sg1 type 0 scsi 3:0:0:0: Direct-Access ATA Maxtor 3H500F0 HA43 PQ: 0 ANSI: 5 sd 3:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: unknown partition table sd 3:0:0:0: [sdc] Attached SCSI disk sd 3:0:0:0: Attached scsi generic sg2 type 0 ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:0f.0 to 64 scsi4 : sata_nv scsi5 : sata_nv ata5: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc000 irq 21 ata6: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc008 irq 21 ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata5.00: ATA-7: WDC WD5000AAKS-00TMA0, 12.01C01, max UDMA/133 ata5.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata5.00: configured for UDMA/133 ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata6.00: ATA-7: Maxtor 6H500F0, HA431DD0, max UDMA/133 ata6.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata6.00: configured for UDMA/133 scsi 4:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 12.0 PQ: 0 ANSI: 5 sd 4:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) sd 4:0:0:0: [sdd] Write Protect is off sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 4:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) sd 4:0:0:0: [sdd] Write Protect is off sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdd: unknown partition table sd 4:0:0:0: [sdd] Attached SCSI disk sd 4:0:0:0: Attached scsi generic sg3 type 0 scsi 5:0:0:0: Direct-Access ATA Maxtor 6H500F0 HA43 PQ: 0 ANSI: 5 sd 5:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB) sd 5:0:0:0: [sde] Write Protect is off sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 5:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB) sd 5:0:0:0: [sde] Write Protect is off sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: unknown partition table sd 5:0:0:0: [sde] Attached SCSI disk sd 5:0:0:0: Attached scsi generic sg4 type 0 pata_amd 0000:00:0d.0: version 0.3.10 PCI: Setting latency timer of device 0000:00:0d.0 to 64 scsi6 : pata_amd scsi7 : pata_amd ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 ata7.00: ATA-7: Maxtor 2F040L0, VAM51JJ0, max UDMA/133 ata7.00: 80293248 sectors, multi 16: LBA ata7.00: configured for UDMA/133 scsi 6:0:0:0: Direct-Access ATA Maxtor 2F040L0 VAM5 PQ: 0 ANSI: 5 sd 6:0:0:0: [sdf] 80293248 512-byte hardware sectors (41110 MB) sd 6:0:0:0: [sdf] Write Protect is off sd 6:0:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 6:0:0:0: [sdf] 80293248 512-byte hardware sectors (41110 MB) sd 6:0:0:0: [sdf] Write Protect is off sd 6:0:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdf: sdf1 sdf2 sdf3 sd 6:0:0:0: [sdf] Attached SCSI disk sd 6:0:0:0: Attached scsi generic sg5 type 0 PCI: Enabling device 0000:02:00.1 (0000 -> 0001) ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16 ACPI: PCI Interrupt 0000:02:00.1[B] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:02:00.1 to 64 scsi8 : pata_jmicron scsi9 : pata_jmicron ata9: PATA max UDMA/100 cmd 0x9000 ctl 0x9400 bmdma 0xa000 irq 16 ata10: PATA max UDMA/100 cmd 0x9800 ctl 0x9c00 bmdma 0xa008 irq 16 ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:0b.1 to 64 ehci_hcd 0000:00:0b.1: EHCI Host Controller ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0b.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:0b.1 ehci_hcd 0000:00:0b.1: irq 20, io mem 0xf9008000 ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:0b.0 to 64 ohci_hcd 0000:00:0b.0: OHCI Host Controller ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0b.0: irq 23, io mem 0xf9007000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 8 ports detected Initializing USB Mass Storage driver... usb 2-4: new low speed USB device using ohci_hcd and address 2 usb 2-4: configuration #1 chosen from 1 choice usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice gameport: EMU10K1 is pci0000:01:07.1/gameport0, io 0x8800, speed 1087kHz input: AT Translated Set 2 keyboard as /class/input/input2 rtc-test rtc-test.0: rtc core: registered test as rtc0 rtc-test rtc-test.1: rtc core: registered test as rtc1 i2c /dev entries driver i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00 i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c80 i2c-parport: adapter type unspecified i2c-parport-light: adapter type unspecified i2c-adapter i2c-1: detect fail: address match, 0x2e pc87360: PC8736x not detected, module not inserted. w83627ehf: Found W83627EHG chip at 0x290 device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@xxxxxxxxxx cpuidle: using governor ladder input: Wireless INC TW Wireless USB Device as /class/input/input3 input: USB HID v1.10 Keyboard [Wireless INC TW Wireless USB Device] on usb-0000:00:0b.0-4 input: Wireless INC TW Wireless USB Device as /class/input/input4 input: USB HID v1.10 Mouse [Wireless INC TW Wireless USB Device] on usb-0000:00:0b.0-4 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20 19:16:42 2007 UTC). ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17 ALSA sound/pci/emu10k1/emufx.c:1545: Installing spdif_bug patch: Audigy 2 ZS [SB0350] usbcore: registered new interface driver snd-usb-audio ALSA device list: #0: Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) at 0x8400, irq 17 Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) ctnetlink v0.93: registering with nfnetlink. ip_tables: (C) 2000-2006 Netfilter Core Team TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 RPC: Registered udp transport module. RPC: Registered tcp transport module. powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ processors (2 cpu cores) (version 2.20.00) powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8 powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12 rtc-test rtc-test.0: setting system clock to 2009-02-27 17:33:18 UTC (1235755998) UDF-fs: No VRS found XFS mounting filesystem sdf3 Starting XFS recovery on filesystem: sdf3 (logdev: internal) Ending XFS recovery on filesystem: sdf3 (logdev: internal) VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 248k freed udev: renamed network interface eth0 to eth3 udev: renamed network interface eth1 to eth2 Filesystem "dm-0": Disabling barriers, not supported by the underlying device XFS mounting filesystem dm-0 Starting XFS recovery on filesystem: dm-0 (logdev: internal) Ending XFS recovery on filesystem: dm-0 (logdev: internal) ip6_tables: (C) 2000-2006 Netfilter Core Team r8169: eth2: link up Clocksource tsc unstable (delta = -101766520 ns) Adding 498004k swap on /dev/sdf2. Priority:-1 extents:1 across:498004k .. snip firewall stuff .. after dmesg: Linux version 2.6.29-rc6-rt3 (root@shapeshifter) (gcc version 4.3.3 (Gentoo 4.3.3 p1.0, pie-10.1.5) ) #2 SMP PREEMPT RT Tue Feb 24 10:18:10 PST 2009 Command line: root=/dev/sdf3 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000beff0000 (usable) BIOS-e820: 00000000beff0000 - 00000000beff3000 (ACPI NVS) BIOS-e820: 00000000beff3000 - 00000000bf000000 (ACPI data) BIOS-e820: 00000000bf000000 - 00000000c0000000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) DMI 2.3 present. last_pfn = 0xbeff0 max_arch_pfn = 0x100000000 init_memory_mapping: 0000000000000000-00000000beff0000 0000000000 - 00bee00000 page 2M 00bee00000 - 00beff0000 page 4k kernel direct mapping tables up to beff0000 @ 8000-d000 last_map_addr: beff0000 end: beff0000 ACPI: RSDP 000F6BC0, 0014 (r0 GBT ) ACPI: RSDT BEFF3000, 0030 (r1 GBT AWRDACPI 42302E31 AWRD 1010101) ACPI: FACP BEFF3040, 0074 (r1 GBT AWRDACPI 42302E31 AWRD 1010101) FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) ACPI: DSDT BEFF30C0, 4D2C (r1 GBT AWRDACPI 1000 MSFT 100000C) ACPI: FACS BEFF0000, 0040 ACPI: MCFG BEFF7E80, 003C (r1 GBT AWRDACPI 42302E31 AWRD 1010101) ACPI: APIC BEFF7E00, 0072 (r1 GBT AWRDACPI 42302E31 AWRD 1010101) ACPI: Local APIC address 0xfee00000 (5 early reservations) ==> bootmem [0000000000 - 00beff0000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #2 [0000200000 - 00009d5d90] TEXT DATA BSS ==> [0000200000 - 00009d5d90] #3 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000] #4 [0000008000 - 000000b000] PGTABLE ==> [0000008000 - 000000b000] found SMP MP-table at [ffff8800000f5210] f5210 [ffffe20000000000-ffffe200029fffff] PMD -> [ffff880001200000-ffff880003bfffff] on node 0 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x00100000 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000000 -> 0x0000009f 0: 0x00000100 -> 0x000beff0 On node 0 totalpages: 782223 DMA zone: 56 pages used for memmap DMA zone: 2109 pages reserved DMA zone: 1834 pages, LIFO batch:0 DMA32 zone: 10640 pages used for memmap DMA32 zone: 767584 pages, LIFO batch:31 Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Using ACPI (MADT) for SMP configuration information SMP: Allowing 2 CPUs, 0 hotplug CPUs nr_irqs_gsi: 24 Allocating PCI resources starting at c4000000 (gap: c0000000:30000000) NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1 PERCPU: Allocating 73728 bytes of per cpu data Real-Time Preemption Support (C) 2004-2007 Ingo Molnar Built 1 zonelists in Zone order, mobility grouping on. Total pages: 769418 Kernel command line: root=/dev/sdf3 Initializing CPU#0 Preemptible RCU implementation. NR_IRQS:320 PID hash table entries: 4096 (order: 12, 32768 bytes) Fast TSC calibration using PIT Detected 2209.886 MHz processor. spurious 8259A interrupt: IRQ7. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Checking aperture... No AGP bridge found Node 0: aperture @ 1620000000 size 32 MB Aperture beyond 4GB. Ignoring. Memory: 3070716k/3129280k available (4912k kernel code, 388k absent, 57716k reserved, 2040k data, 388k init) Calibrating delay loop (skipped), value calculated using timer frequency.. 4421.92 BogoMIPS (lpj=7366286) Security Framework initialized Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) tseg: 0000000000 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 ACPI: Core revision 20081204 Setting APIC routing to flat ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1 CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01 Booting processor 1 APIC 0x1 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4421.01 BogoMIPS (lpj=7366419) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01 Brought up 2 CPUs Total of 2 processors activated (8843.94 BogoMIPS). CPU0 attaching sched-domain: domain 0: span 0-1 level CPU groups: 0 1 CPU1 attaching sched-domain: domain 0: span 0-1 level CPU groups: 1 0 net_namespace: 1880 bytes NET: Registered protocol family 16 node 0 link 0: io port [3000, fffff] TOM: 00000000c0000000 aka 3072M node 0 link 0: mmio [f0000000, f1ffffff] node 0 link 0: mmio [a0000, bffff] node 0 link 0: mmio [c0000000, ffb7ffff] bus: [00,ff] on node 0 link 0 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [c0000000, fcffffffff] bus: 00 index 2 mmio: [a0000, bffff] ACPI: bus type pci registered PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 PCI: MCFG area at f0000000 reserved in E820 PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 31 PCI: Using MMCONFIG at f0000000 - f1ffffff PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0 ACPI: EC: Look up EC in DSDT ACPI Warning (dsobject-0502): Package List length (6) larger than NumElements count (2), truncated [20081204] ACPI Warning (dsobject-0502): Package List length (6) larger than NumElements count (2), truncated [20081204] ACPI: Denied BIOS AML access to invalid port 0x4d0+0x2 (ELCR) ACPI Exception (dsopcode-0419): AE_AML_ILLEGAL_ADDRESS, During address validation of OpRegion [ELCR] [20081204] ACPI: Interpreter enabled ACPI: (supports S0 S1 S5) ACPI: Using IOAPIC for interrupt routing ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:03.0: PME# disabled pci 0000:00:05.0: reg 10 32bit mmio: [0xf2000000-0xf2ffffff] pci 0000:00:05.0: reg 14 64bit mmio: [0xe0000000-0xefffffff] pci 0000:00:05.0: reg 1c 64bit mmio: [0xf5000000-0xf5ffffff] pci 0000:00:05.0: reg 30 32bit mmio: [0x000000-0x01ffff] HPET not enabled in BIOS. You might try hpet=force boot option pci 0000:00:0a.1: reg 20 io port: [0x1c00-0x1c3f] pci 0000:00:0a.1: reg 24 io port: [0x1c80-0x1cbf] pci 0000:00:0a.1: PME# supported from D3hot D3cold pci 0000:00:0a.1: PME# disabled pci 0000:00:0b.0: reg 10 32bit mmio: [0xf9007000-0xf9007fff] pci 0000:00:0b.0: supports D1 D2 pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:0b.0: PME# disabled pci 0000:00:0b.1: reg 10 32bit mmio: [0xf9008000-0xf90080ff] pci 0000:00:0b.1: supports D1 D2 pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:0b.1: PME# disabled pci 0000:00:0d.0: reg 20 io port: [0xf000-0xf00f] pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7] pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3] pci 0000:00:0e.0: reg 18 io port: [0x970-0x977] pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73] pci 0000:00:0e.0: reg 20 io port: [0xd400-0xd40f] pci 0000:00:0e.0: reg 24 32bit mmio: [0xf9006000-0xf9006fff] pci 0000:00:0f.0: reg 10 io port: [0x9e0-0x9e7] pci 0000:00:0f.0: reg 14 io port: [0xbe0-0xbe3] pci 0000:00:0f.0: reg 18 io port: [0x960-0x967] pci 0000:00:0f.0: reg 1c io port: [0xb60-0xb63] pci 0000:00:0f.0: reg 20 io port: [0xc000-0xc00f] pci 0000:00:0f.0: reg 24 32bit mmio: [0xf9005000-0xf9005fff] pci 0000:00:10.1: reg 10 32bit mmio: [0xf9000000-0xf9003fff] pci 0000:00:10.1: PME# supported from D3hot D3cold pci 0000:00:10.1: PME# disabled pci 0000:00:14.0: reg 10 32bit mmio: [0xf9004000-0xf9004fff] pci 0000:00:14.0: reg 14 io port: [0xe000-0xe007] pci 0000:00:14.0: supports D1 D2 pci 0000:00:14.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:14.0: PME# disabled pci 0000:02:00.0: reg 24 32bit mmio: [0xf8000000-0xf8001fff] pci 0000:02:00.0: reg 30 32bit mmio: [0x000000-0x00ffff] pci 0000:02:00.0: PME# supported from D3hot pci 0000:02:00.0: PME# disabled pci 0000:02:00.1: reg 10 io port: [0x9000-0x9007] pci 0000:02:00.1: reg 14 io port: [0x9400-0x9403] pci 0000:02:00.1: reg 18 io port: [0x9800-0x9807] pci 0000:02:00.1: reg 1c io port: [0x9c00-0x9c03] pci 0000:02:00.1: reg 20 io port: [0xa000-0xa00f] pci 0000:00:03.0: bridge io port: [0x9000-0xafff] pci 0000:00:03.0: bridge 32bit mmio: [0xf7000000-0xf8ffffff] pci 0000:01:06.0: reg 10 io port: [0x8000-0x80ff] pci 0000:01:06.0: reg 14 32bit mmio: [0xf4005000-0xf40050ff] pci 0000:01:06.0: reg 30 32bit mmio: [0x000000-0x01ffff] pci 0000:01:06.0: supports D1 D2 pci 0000:01:06.0: PME# supported from D1 D2 D3hot D3cold pci 0000:01:06.0: PME# disabled pci 0000:01:07.0: reg 10 io port: [0x8400-0x843f] pci 0000:01:07.0: supports D1 D2 pci 0000:01:07.1: reg 10 io port: [0x8800-0x8807] pci 0000:01:07.1: supports D1 D2 pci 0000:01:07.2: reg 10 32bit mmio: [0xf4004000-0xf40047ff] pci 0000:01:07.2: reg 14 32bit mmio: [0xf4000000-0xf4003fff] pci 0000:01:07.2: supports D1 D2 pci 0000:01:07.2: PME# supported from D0 D1 D2 D3hot pci 0000:01:07.2: PME# disabled pci 0000:00:10.0: transparent bridge pci 0000:00:10.0: bridge io port: [0x8000-0x8fff] pci 0000:00:10.0: bridge 32bit mmio: [0xf3000000-0xf4ffffff] pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMAC] (IRQs 5 *7 9 10 11 14 15) ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LAZA] (IRQs 5 *7 9 10 11 14 15) ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 5 *7 9 10 11 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0 ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0 ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0 ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0 ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0 ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0 SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 9 devices ACPI: ACPI bus type pnp unregistered system 00:01: ioport range 0x1000-0x107f has been reserved system 00:01: ioport range 0x1080-0x10ff has been reserved system 00:01: ioport range 0x1400-0x147f has been reserved system 00:01: ioport range 0x1480-0x14ff has been reserved system 00:01: ioport range 0x1800-0x187f has been reserved system 00:01: ioport range 0x1880-0x18ff has been reserved system 00:01: ioport range 0x2000-0x207f has been reserved system 00:01: ioport range 0x2080-0x20ff has been reserved system 00:01: iomem range 0xfefe0000-0xfefe01ff has been reserved system 00:01: iomem range 0xbf000000-0xbfffffff has been reserved system 00:01: iomem range 0xf0000000-0xf1ffffff has been reserved system 00:02: ioport range 0x4d0-0x4d1 has been reserved system 00:02: ioport range 0x290-0x29f has been reserved system 00:08: iomem range 0xd3000-0xd3fff has been reserved system 00:08: iomem range 0xf0000-0xf7fff could not be reserved system 00:08: iomem range 0xf8000-0xfbfff could not be reserved system 00:08: iomem range 0xfc000-0xfffff could not be reserved system 00:08: iomem range 0xbeff0000-0xbeffffff could not be reserved system 00:08: iomem range 0xffff0000-0xffffffff has been reserved system 00:08: iomem range 0x0-0x9ffff could not be reserved system 00:08: iomem range 0x100000-0xbefeffff could not be reserved system 00:08: iomem range 0xbf000000-0xbfffffff has been reserved system 00:08: iomem range 0xfec00000-0xfec00fff has been reserved system 00:08: iomem range 0xfee00000-0xfee00fff has been reserved pci 0000:00:03.0: PCI bridge, secondary bus 0000:02 pci 0000:00:03.0: IO window: 0x9000-0xafff pci 0000:00:03.0: MEM window: 0xf7000000-0xf8ffffff pci 0000:00:03.0: PREFETCH window: 0x000000c4000000-0x000000c40fffff pci 0000:00:10.0: PCI bridge, secondary bus 0000:01 pci 0000:00:10.0: IO window: 0x8000-0x8fff pci 0000:00:10.0: MEM window: 0xf3000000-0xf4ffffff pci 0000:00:10.0: PREFETCH window: 0x000000c4100000-0x000000c41fffff pci 0000:00:03.0: setting latency timer to 64 pci 0000:00:10.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x00-0xffff] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] pci_bus 0000:02: resource 0 io: [0x9000-0xafff] pci_bus 0000:02: resource 1 mem: [0xf7000000-0xf8ffffff] pci_bus 0000:02: resource 2 mem: [0xc4000000-0xc40fffff] pci_bus 0000:02: resource 3 mem: [0x0-0x0] pci_bus 0000:01: resource 0 io: [0x8000-0x8fff] pci_bus 0000:01: resource 1 mem: [0xf3000000-0xf4ffffff] pci_bus 0000:01: resource 2 mem: [0xc4100000-0xc41fffff] pci_bus 0000:01: resource 3 io: [0x00-0xffff] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 10, 4194304 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered NET: Registered protocol family 1 Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). fuse init (API version 7.11) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 5998 alg: No test for stdrng (krng) io scheduler noop registered io scheduler cfq registered (default) pci 0000:00:00.0: Enabling HT MSI Mapping pci 0000:00:03.0: Enabling HT MSI Mapping pci 0000:00:05.0: Boot video device pci 0000:00:09.0: Enabling HT MSI Mapping pci 0000:00:0e.0: Enabling HT MSI Mapping pci 0000:00:0f.0: Enabling HT MSI Mapping pci 0000:00:10.0: Enabling HT MSI Mapping pci 0000:00:10.1: Enabling HT MSI Mapping pcieport-driver 0000:00:03.0: setting latency timer to 64 pcieport-driver 0000:00:03.0: irq 24 for MSI/MSI-X input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] processor ACPI_CPU:00: registered as cooling_device0 processor ACPI_CPU:01: registered as cooling_device1 lp: driver loaded but no devices found Linux agpgart interface v0.103 loop: module loaded forcedeth: Reverse Engineered nForce ethernet driver. Version 0.62. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 forcedeth 0000:00:14.0: PCI INT A -> Link[APCH] -> GSI 23 (level, low) -> IRQ 23 forcedeth 0000:00:14.0: setting latency timer to 64 nv_probe: set workaround bit for reversed mac addr forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x3f1 @ 7, addr 00:14:85:35:ce:4d forcedeth 0000:00:14.0: highdma pwrctl timirq gbit lnktim desc-v3 r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 r8169 0000:01:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16 r8169 0000:01:06.0: no PCI Express capability eth1: RTL8110s at 0xffffc2000001e000, 00:40:f4:a6:5c:ea, XID 04000000 IRQ 16 usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver rndis_host usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus Driver 'sd' needs updating - please use bus_type methods ahci 0000:02:00.0: version 3.0 ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16 ahci 0000:02:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16 ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part ahci 0000:02:00.0: setting latency timer to 64 scsi0 : ahci scsi1 : ahci ata1: SATA max UDMA/133 abar m8192@0xf8000000 port 0xf8000100 irq 16 ata2: SATA max UDMA/133 abar m8192@0xf8000000 port 0xf8000180 irq 16 ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-8: WDC WD10EACS-00ZJB0, 01.01B01, max UDMA/133 ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD10EACS-00Z 01.0 PQ: 0 ANSI: 5 sd 1:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: unknown partition table sd 1:0:0:0: [sda] Attached SCSI disk sd 1:0:0:0: Attached scsi generic sg0 type 0 sata_nv 0000:00:0e.0: version 3.5 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22 sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 22 (level, low) -> IRQ 22 sata_nv 0000:00:0e.0: Using SWNCQ mode sata_nv 0000:00:0e.0: setting latency timer to 64 scsi2 : sata_nv scsi3 : sata_nv ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 22 ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 22 ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-7: Maxtor 3H500F0, HA431BV0, max UDMA/133 ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133 isa bounce pool size: 16 pages scsi 2:0:0:0: Direct-Access ATA Maxtor 3H500F0 HA43 PQ: 0 ANSI: 5 ata3.00: Disabling SWNCQ mode (depth 1) sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: unknown partition table sd 2:0:0:0: [sdb] Attached SCSI disk sd 2:0:0:0: Attached scsi generic sg1 type 0 ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: ATA-7: Maxtor 3H500F0, HA431BV0, max UDMA/133 ata4.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.00: configured for UDMA/133 scsi 3:0:0:0: Direct-Access ATA Maxtor 3H500F0 HA43 PQ: 0 ANSI: 5 ata4.00: Disabling SWNCQ mode (depth 1) sd 3:0:0:0: [sdc] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdc] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: unknown partition table sd 3:0:0:0: [sdc] Attached SCSI disk sd 3:0:0:0: Attached scsi generic sg2 type 0 ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21 sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 21 (level, low) -> IRQ 21 sata_nv 0000:00:0f.0: Using SWNCQ mode sata_nv 0000:00:0f.0: setting latency timer to 64 scsi4 : sata_nv scsi5 : sata_nv ata5: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc000 irq 21 ata6: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc008 irq 21 ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata5.00: ATA-7: WDC WD5000AAKS-00TMA0, 12.01C01, max UDMA/133 ata5.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata5.00: configured for UDMA/133 scsi 4:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 12.0 PQ: 0 ANSI: 5 sd 4:0:0:0: [sdd] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 4:0:0:0: [sdd] Write Protect is off sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 4:0:0:0: [sdd] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 4:0:0:0: [sdd] Write Protect is off sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdd: unknown partition table sd 4:0:0:0: [sdd] Attached SCSI disk sd 4:0:0:0: Attached scsi generic sg3 type 0 ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata6.00: ATA-7: Maxtor 6H500F0, HA431DD0, max UDMA/133 ata6.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata6.00: configured for UDMA/133 scsi 5:0:0:0: Direct-Access ATA Maxtor 6H500F0 HA43 PQ: 0 ANSI: 5 ata6.00: Disabling SWNCQ mode (depth 1) sd 5:0:0:0: [sde] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 5:0:0:0: [sde] Write Protect is off sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 5:0:0:0: [sde] 976773168 512-byte hardware sectors: (500 GB/465 GiB) sd 5:0:0:0: [sde] Write Protect is off sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: unknown partition table sd 5:0:0:0: [sde] Attached SCSI disk sd 5:0:0:0: Attached scsi generic sg4 type 0 pata_amd 0000:00:0d.0: version 0.3.11 pata_amd 0000:00:0d.0: setting latency timer to 64 scsi6 : pata_amd scsi7 : pata_amd ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 ata7.00: ATA-7: Maxtor 2F040L0, VAM51JJ0, max UDMA/133 ata7.00: 80293248 sectors, multi 16: LBA ata7: nv_mode_filter: 0x7f39f&0x7f01f->0x7f01f, BIOS=0x7f000 (0xc7000000) ACPI=0x7f01f (15:600:0x13) ata7.00: configured for UDMA/133 scsi 6:0:0:0: Direct-Access ATA Maxtor 2F040L0 VAM5 PQ: 0 ANSI: 5 sd 6:0:0:0: [sdf] 80293248 512-byte hardware sectors: (41.1 GB/38.2 GiB) sd 6:0:0:0: [sdf] Write Protect is off sd 6:0:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 6:0:0:0: [sdf] 80293248 512-byte hardware sectors: (41.1 GB/38.2 GiB) sd 6:0:0:0: [sdf] Write Protect is off sd 6:0:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdf: sdf1 sdf2 sdf3 sd 6:0:0:0: [sdf] Attached SCSI disk sd 6:0:0:0: Attached scsi generic sg5 type 0 pata_jmicron 0000:02:00.1: enabling device (0000 -> 0001) ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16 pata_jmicron 0000:02:00.1: PCI INT B -> Link[APC6] -> GSI 16 (level, low) -> IRQ 16 pata_jmicron 0000:02:00.1: setting latency timer to 64 scsi8 : pata_jmicron scsi9 : pata_jmicron ata9: PATA max UDMA/100 cmd 0x9000 ctl 0x9400 bmdma 0xa000 irq 16 ata10: PATA max UDMA/100 cmd 0x9800 ctl 0x9c00 bmdma 0xa008 irq 16 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20 ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 20 (level, low) -> IRQ 20 ehci_hcd 0000:00:0b.1: setting latency timer to 64 ehci_hcd 0000:00:0b.1: EHCI Host Controller ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0b.1: debug port 1 ehci_hcd 0000:00:0b.1: cache line size of 64 is not supported ehci_hcd 0000:00:0b.1: irq 20, io mem 0xf9008000 ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.29-rc6-rt3 ehci_hcd usb usb1: SerialNumber: 0000:00:0b.1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23 ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23 ohci_hcd 0000:00:0b.0: setting latency timer to 64 ohci_hcd 0000:00:0b.0: OHCI Host Controller ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0b.0: irq 23, io mem 0xf9007000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.29-rc6-rt3 ohci_hcd usb usb2: SerialNumber: 0000:00:0b.0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 8 ports detected PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp serio: i8042 KBD port at 0x60,0x64 irq 1 gameport: EMU10K1 is pci0000:01:07.1/gameport0, io 0x8800, speed 1088kHz mice: PS/2 mouse device common for all mice rtc-test rtc-test.0: rtc core: registered test as rtc0 rtc-test rtc-test.1: rtc core: registered test as rtc1 i2c /dev entries driver i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00 i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c80 i2c-parport: adapter type unspecified i2c-parport-light: adapter type unspecified input: AT Translated Set 2 keyboard as /class/input/input2 usb 2-4: new low speed USB device using ohci_hcd and address 2 usb 2-4: New USB device found, idVendor=0a91, idProduct=3801 usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-4: Product: Wireless USB Device usb 2-4: Manufacturer: Wireless INC TW usb 2-4: configuration #1 chosen from 1 choice i2c-adapter i2c-1: detect fail: address match, 0x2e pc87360: PC8736x not detected, module not inserted. w83627ehf: Found W83627EHG chip at 0x290 device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@xxxxxxxxxx cpuidle: using governor ladder input: Wireless INC TW Wireless USB Device as /class/input/input3 generic-usb 0003:0A91:3801.0001: input: USB HID v1.10 Keyboard [Wireless INC TW Wireless USB Device] on usb-0000:00:0b.0-4/input0 input: Wireless INC TW Wireless USB Device as /class/input/input4 generic-usb 0003:0A91:3801.0002: input: USB HID v1.10 Mouse [Wireless INC TW Wireless USB Device] on usb-0000:00:0b.0-4/input1 usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.18a. ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 EMU10K1_Audigy 0000:01:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17 ALSA sound/pci/emu10k1/emufx.c:1546: Installing spdif_bug patch: SB Audigy 2 ZS [SB0350] usbcore: registered new interface driver snd-usb-audio ALSA device list: #0: SB Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) at 0x8400, irq 17 Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ctnetlink v0.93: registering with nfnetlink. ip_tables: (C) 2000-2006 Netfilter Core Team TCP bic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 RPC: Registered udp transport module. RPC: Registered tcp transport module. powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ processors (2 cpu cores) (version 2.20.00) powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8 powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12 rtc-test rtc-test.0: setting system clock to 2009-02-27 17:13:18 UTC (1235754798) UDF-fs: No VRS found XFS mounting filesystem sdf3 Ending clean XFS mount for filesystem: sdf3 VFS: Mounted root (xfs filesystem) readonly on device 8:83. Freeing unused kernel memory: 388k freed udev: renamed network interface eth0 to eth3 udev: renamed network interface eth1 to eth2 Filesystem "dm-0": Disabling barriers, trial barrier write failed XFS mounting filesystem dm-0 Ending clean XFS mount for filesystem: dm-0 ip6_tables: (C) 2000-2006 Netfilter Core Team r8169: eth2: link up Clocksource tsc unstable (delta = -271719379 ns) eth3: no link during initialization. ADDRCONF(NETDEV_UP): eth3: link is not ready eth3: link up. ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready eth2: no IPv6 routers present .. snip more firewall stuff .. Adding 498004k swap on /dev/sdf2. Priority:-1 extents:1 across:498004k eth3: no IPv6 routers present .. snip firewall stuff .. ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata4.00: cmd 35/00:10:b0:70:75/00:00:1f:00:00/e0 tag 0 dma 8192 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata4.00: status: { DRDY } ata4: hard resetting link ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: configured for UDMA/133 ata4: EH complete .. snip more firewall stuff.. ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata4.00: cmd 35/00:10:b0:70:75/00:00:1f:00:00/e0 tag 0 dma 8192 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata4.00: status: { DRDY } ata4: hard resetting link ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: configured for UDMA/133 ata4: EH complete Connection attempt (UNPRIV): IN=eth3 OUT= MAC=00:14:85:35:ce:4d:00:0f:35:bf:d8:01:08:00 SRC=218.174.129.152 DST=98.224.98.19 LEN=126 TOS=0x00 PREC=0x20 TTL=108 ID=59452 PROTO=UDP SPT=30164 DPT=6881 LEN=106 INFO: task rtorrent:3649 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. rtorrent T (004) [ffff8800b41e9060] ffffffff8028305b 0 3649 3647 ffff8800bebba850 0000000000000086 ffff8800be1b9528 ffff8800be1b0a00 000000000000ea40 ffff8800be1b0a00 ffff8800be1c6800 000000000000ea40 ffff8800b41e9060 ffff8800b41e92f8 00000001be1c6a58 00000000ffffa9ad Call Trace: [<ffffffff80285bc0>] ? sync_page+0x0/0x70 [<ffffffff80285bc0>] ? sync_page+0x0/0x70 [<ffffffff806c7a5a>] ? schedule+0xa/0x30 [<ffffffff806c7ab4>] ? io_schedule+0x34/0x50 [<ffffffff80285bf5>] ? sync_page+0x35/0x70 [<ffffffff806c7d3a>] ? __wait_on_bit_lock+0x4a/0xa0 [<ffffffff80285b9e>] ? __lock_page+0x5e/0x70 [<ffffffff80257fd0>] ? wake_bit_function+0x0/0x30 [<ffffffff80285d30>] ? find_lock_page+0x60/0x80 [<ffffffff802864fa>] ? filemap_fault+0x33a/0x4c0 [<ffffffff8029a395>] ? __do_fault+0x65/0x440 [<ffffffff805d34ba>] ? __qdisc_run+0xda/0x2d0 [<ffffffff8029c7c6>] ? handle_mm_fault+0x1f6/0x770 [<ffffffff8022ac5c>] ? do_page_fault+0x10c/0x320 [<ffffffff8022ac5c>] ? do_page_fault+0x10c/0x320 [<ffffffff806c9acf>] ? page_fault+0x1f/0x30 [<ffffffff806a19fc>] ? csum_partial_copy_from_user+0xac/0x100 [<ffffffff8060ac12>] ? tcp_sendmsg+0x1e2/0xb40 [<ffffffff805b2d6b>] ? sock_sendmsg+0xcb/0x100 [<ffffffff80282e45>] ? perf_counter_task_sched_in+0x65/0x1b0 [<ffffffff80257fa0>] ? autoremove_wake_function+0x0/0x30 [<ffffffff8024b884>] ? lock_timer_base+0x34/0x70 [<ffffffff8024c378>] ? del_timer_sync+0x18/0x30 [<ffffffff805b2322>] ? sockfd_lookup_light+0x22/0x90 [<ffffffff805b3229>] ? sys_sendto+0x119/0x180 [<ffffffff802b320e>] ? fget+0x7e/0xa0 [<ffffffff802e2296>] ? sys_epoll_wait+0x106/0x5a0 [<ffffffff8020c31b>] ? system_call_fastpath+0x16/0x1b .. snip more firewall stuff .. ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata4.00: cmd 35/00:10:b0:70:75/00:00:1f:00:00/e0 tag 0 dma 8192 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata4.00: status: { DRDY } ata4: hard resetting link ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: configured for UDMA/133 ata4: EH complete -- avuton -- | (\_/) This is Bunny. Copy and paste Bunny | (='.'=) into your signature to help him gain | (")_(") world domination. -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
