I'd like to know one thing: Is this a hardware bug or a software bug. When I write a DVD-RW with growisofs and there's some (media) error, I get some ata errors and DVD's led stays green, and I can't reset the drive, eject disk with software or by pressing drive's eject button. It does not matter if I open the drive door and put in some other disc. I have SATA drive HL-DT-ST DVD-RAM GH22NS30 1.01, one SATA hard disk, one PATA hard disk, Intel motherboard DQ965GF version CO96510J.86A.6079.2008.0727.2220, Linux x86_64 2.6.27.10. I already wrote to LG (manufacturer of DVD drive) a couple of weeks ago but I have not heard back. At around 01:57:08.431689628 I opened case and replugged power cable from the DVD drive. Kernel detected it, but then after some seconds I got something like "hda: command timed out" and then hard freeze (had to power cycle). No kernel messages were available after 01:57:55.999123925. 2008-12-23 01:44:55.656343805 <3>[17524.249147] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen 2008-12-23 01:44:55.656346265 <3>[17524.249158] ata4.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 2008-12-23 01:44:55.656347206 <3>[17524.249159] cdb 54 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2008-12-23 01:44:55.656348135 <3>[17524.249161] res 40/00:03:00:18:00/00:00:00:00:00/a0 Emask 0x4 (timeout) 2008-12-23 01:44:55.656349088 <3>[17524.249164] ata4.00: status: { DRDY } 2008-12-23 01:44:55.656349714 <6>[17524.249171] ata4: hard resetting link 2008-12-23 01:44:55.961280094 <6>[17524.554144] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 2008-12-23 01:44:55.964089698 <6>[17524.556852] ata4.00: configured for UDMA/100 2008-12-23 01:44:55.964091029 <6>[17524.556875] ata4: EH complete 2008-12-23 01:45:55.966348828 <3>[17584.559149] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen 2008-12-23 01:45:55.966351426 <3>[17584.559161] ata4.00: cmd a0/01:00:00:00:80/00:00:00:00:00/a0 tag 0 dma 32768 out 2008-12-23 01:45:55.966352479 <3>[17584.559163] cdb 2a 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 2008-12-23 01:45:55.966353405 <3>[17584.559164] res 40/00:03:00:18:00/00:00:00:00:00/a0 Emask 0x4 (timeout) 2008-12-23 01:45:55.966354339 <3>[17584.559167] ata4.00: status: { DRDY } 2008-12-23 01:45:55.966354962 <6>[17584.559174] ata4: hard resetting link 2008-12-23 01:45:56.271288460 <6>[17584.864145] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 2008-12-23 01:45:56.275602728 <6>[17584.866809] ata4.00: configured for UDMA/100 2008-12-23 01:45:56.275606194 <6>[17584.866831] ata4: EH complete 2008-12-23 01:49:58.286330148 <4>[17826.879146] ata4: limiting SATA link speed to 1.5 Gbps 2008-12-23 01:49:58.286366841 <3>[17826.879154] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen 2008-12-23 01:49:58.286390100 <3>[17826.879162] ata4.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 2008-12-23 01:49:58.286412270 <3>[17826.879163] cdb 1b 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 2008-12-23 01:49:58.286434918 <3>[17826.879165] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout) 2008-12-23 01:49:58.286456553 <3>[17826.879168] ata4.00: status: { DRDY } 2008-12-23 01:49:58.286477612 <6>[17826.879174] ata4: hard resetting link 2008-12-23 01:49:58.591286039 <6>[17827.184144] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 2008-12-23 01:49:58.593975535 <6>[17827.186848] ata4.00: configured for UDMA/100 2008-12-23 01:49:58.593998258 <6>[17827.186861] ata4: EH complete 2008-12-23 01:50:28.593347236 <3>[17857.186147] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen 2008-12-23 01:50:28.593349616 <3>[17857.186159] ata4.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 2008-12-23 01:50:28.593350529 <3>[17857.186160] cdb 1b 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 2008-12-23 01:50:28.593351407 <3>[17857.186162] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout) 2008-12-23 01:50:28.593352291 <3>[17857.186165] ata4.00: status: { DRDY } 2008-12-23 01:50:28.593352886 <6>[17857.186172] ata4: hard resetting link 2008-12-23 01:50:28.898286191 <6>[17857.491144] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 2008-12-23 01:50:28.901031752 <6>[17857.493899] ata4.00: configured for UDMA/100 2008-12-23 01:50:28.901032973 <6>[17857.493913] ata4: EH complete 2008-12-23 01:50:58.900353887 <3>[17887.493149] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen 2008-12-23 01:50:58.900356575 <3>[17887.493161] ata4.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 2008-12-23 01:50:58.900357474 <3>[17887.493162] cdb 1b 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 2008-12-23 01:50:58.900358367 <3>[17887.493163] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout) 2008-12-23 01:50:58.900359250 <3>[17887.493167] ata4.00: status: { DRDY } 2008-12-23 01:50:58.900359846 <6>[17887.493173] ata4: hard resetting link 2008-12-23 01:50:59.205287636 <6>[17887.798145] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 2008-12-23 01:50:59.208045366 <6>[17887.800847] ata4.00: configured for UDMA/100 2008-12-23 01:50:59.208046752 <6>[17887.800867] ata4: EH complete 2008-12-23 01:50:59.208047308 <3>[17887.800878] sr0: CDROM (ioctl) error, command: Start/Stop Unit 1b 00 00 00 03 00 2008-12-23 01:50:59.208048206 <6>[17887.800888] sr: Sense Key : Aborted Command [current] [descriptor] 2008-12-23 01:50:59.208049019 <6>[17887.800894] sr: Add. Sense: No additional sense information 2008-12-23 01:57:08.431689628 <4>[18257.024504] ata4.00: limiting speed to UDMA/66:PIO4 2008-12-23 01:57:08.431691932 <3>[18257.024511] ata4: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xe frozen 2008-12-23 01:57:08.431692873 <3>[18257.024514] ata4: irq_stat 0x00400000, PHY RDY changed 2008-12-23 01:57:08.431693654 <3>[18257.024518] ata4: SError: { PHYRdyChg } 2008-12-23 01:57:08.431694295 <6>[18257.024525] ata4: hard resetting link 2008-12-23 01:57:09.154282182 <6>[18257.747142] ata4: SATA link down (SStatus 0 SControl 310) 2008-12-23 01:57:14.154273371 <6>[18262.747136] ata4: hard resetting link 2008-12-23 01:57:14.459278255 <6>[18263.052141] ata4: SATA link down (SStatus 0 SControl 310) 2008-12-23 01:57:19.459276252 <6>[18268.052136] ata4: hard resetting link 2008-12-23 01:57:19.766261425 <6>[18268.357141] ata4: SATA link down (SStatus 0 SControl 310) 2008-12-23 01:57:19.766264578 <4>[18268.357150] ata4.00: disabled 2008-12-23 01:57:19.766265221 <6>[18268.357161] ata4: EH complete 2008-12-23 01:57:19.766265872 <6>[18268.357173] ata4.00: detaching (SCSI 3:0:0:0) here I gave the stupid drive some power 2008-12-23 01:57:55.266490475 <3>[18303.859302] ata4: exception Emask 0x10 SAct 0x0 SErr 0x4050002 action 0xe frozen 2008-12-23 01:57:55.266493160 <3>[18303.859309] ata4: irq_stat 0x00000040, connection status changed 2008-12-23 01:57:55.266494069 <3>[18303.859313] ata4: SError: { RecovComm PHYRdyChg CommWake DevExch } 2008-12-23 01:57:55.266494925 <6>[18303.859322] ata4: hard resetting link 2008-12-23 01:57:55.989291809 <6>[18304.582144] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 2008-12-23 01:57:55.990426641 <6>[18304.583305] ata4.00: ATAPI: HL-DT-STDVD-RAM GH22NS30, 1.01, max UDMA/100 2008-12-23 01:57:55.991877936 <6>[18304.584755] ata4.00: configured for UDMA/100 2008-12-23 01:57:55.991879143 <6>[18304.584765] ata4: EH complete 2008-12-23 01:57:55.993043771 <5>[18304.585931] scsi 3:0:0:0: CD-ROM HL-DT-ST DVD-RAM GH22NS30 1.01 PQ: 0 ANSI: 5 2008-12-23 01:57:55.998279657 <4>[18304.591138] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray 2008-12-23 01:57:55.998469034 <7>[18304.591361] sr 3:0:0:0: Attached scsi CD-ROM sr0 2008-12-23 01:57:55.999123925 <5>[18304.592000] sr 3:0:0:0: Attached scsi generic sg1 type 5 CPU0 CPU1 0: 29 0 IO-APIC-edge timer 1: 2 0 IO-APIC-edge i8042 4: 2 0 IO-APIC-edge 7: 0 0 IO-APIC-edge parport0 8: 1 0 IO-APIC-edge rtc0 9: 0 0 IO-APIC-fasteoi acpi 12: 7 0 IO-APIC-edge i8042 14: 0 0 IO-APIC-edge ide2 15: 0 0 IO-APIC-edge ide3 16: 255281 38243 IO-APIC-fasteoi uhci_hcd:usb1, i915@pci:0000:00:02.0 17: 802 3089 IO-APIC-fasteoi ide0, ide1 18: 2 0 IO-APIC-fasteoi ehci_hcd:usb3, uhci_hcd:usb6 19: 15804 10247 IO-APIC-fasteoi uhci_hcd:usb5, ohci1394 21: 48 0 IO-APIC-fasteoi uhci_hcd:usb2 23: 3 0 IO-APIC-fasteoi uhci_hcd:usb4, ehci_hcd:usb7 504: 3109 12186 PCI-MSI-edge HDA Intel 505: 70 7239 PCI-MSI-edge eth0 506: 11427 24155 PCI-MSI-edge ahci NMI: 0 0 Non-maskable interrupts LOC: 2097539 2126841 Local timer interrupts RES: 4740 3811 Rescheduling interrupts CAL: 31978 737 function call interrupts TLB: 669 831 TLB shootdowns TRM: 0 0 Thermal event interrupts THR: 0 0 Threshold APIC interrupts SPU: 0 0 Spurious interrupts ERR: 0 -- "If it bleeds, we can kill it." - Arnold Schwarzenegger
Linux version 2.6.27.10 (safari@xxxxxxxxxxxxxxxxxx) (gcc version 4.3.2 20081105 (Red Hat 4.3.2-7) (GCC) ) #26 SMP Mon Dec 22 03:06:48 EET 2008 Command line: grub_kernel=bzImage-2.6.27.10-012 ro root=/dev/sda6 ide-pci-generic.all-generic-ide vga=6 noisapnp enforcing=0 selinux=0 printk.time=1 log_buf_len=512k KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000008f000 (usable) BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000be584000 (usable) BIOS-e820: 00000000be584000 - 00000000be591000 (reserved) BIOS-e820: 00000000be591000 - 00000000be620000 (usable) BIOS-e820: 00000000be620000 - 00000000be6df000 (ACPI NVS) BIOS-e820: 00000000be6df000 - 00000000be6f0000 (usable) BIOS-e820: 00000000be6f0000 - 00000000be6f2000 (ACPI NVS) BIOS-e820: 00000000be6f2000 - 00000000be6ff000 (ACPI data) BIOS-e820: 00000000be6ff000 - 00000000be700000 (usable) BIOS-e820: 00000000be700000 - 00000000bf000000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f8000000 (reserved) BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) DMI 2.4 present. last_pfn = 0xbe700 max_arch_pfn = 0x3ffffffff x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 init_memory_mapping 0000000000 - 00be600000 page 2M 00be600000 - 00be700000 page 4k kernel direct mapping tables up to be700000 @ 8000-d000 last_map_addr: be700000 end: be700000 ACPI: RSDP 000FE020, 0014 (r0 INTEL ) ACPI: RSDT BE6FD038, 0040 (r1 INTEL DQ965GF 17BF 1000013) ACPI: FACP BE6FC000, 0074 (r1 INTEL DQ965GF 17BF MSFT 1000013) ACPI: DSDT BE6F7000, 4304 (r1 INTEL DQ965GF 17BF MSFT 1000013) ACPI: FACS BE687000, 0040 ACPI: APIC BE6F6000, 0078 (r1 INTEL DQ965GF 17BF MSFT 1000013) ACPI: WDDT BE6F5000, 0040 (r1 INTEL DQ965GF 17BF MSFT 1000013) ACPI: MCFG BE6F4000, 003C (r1 INTEL DQ965GF 17BF MSFT 1000013) ACPI: ASF! BE6F3000, 00A6 (r32 INTEL DQ965GF 17BF MSFT 1000013) ACPI: HPET BE6F2000, 0038 (r1 INTEL DQ965GF 17BF MSFT 1000013) ACPI: TCPA BE620000, 0032 (r2 INTEL TIANO 2 MSFT 1000013) (5 early reservations) ==> bootmem [0000000000 - 00be700000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #2 [0000200000 - 0000980fa8] TEXT DATA BSS ==> [0000200000 - 0000980fa8] #3 [000009e000 - 0000100000] BIOS reserved ==> [000009e000 - 0000100000] #4 [0000008000 - 000000b000] PGTABLE ==> [0000008000 - 000000b000] found SMP MP-table at [ffff8800000fe200] 000fe200 [ffffe20000000000-ffffe200029fffff] PMD -> [ffff880001200000-ffff880003bfffff] on node 0 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x00100000 Movable zone start PFN for each node early_node_map[5] active PFN ranges 0: 0x00000000 -> 0x0000008f 0: 0x00000100 -> 0x000be584 0: 0x000be591 -> 0x000be620 0: 0x000be6df -> 0x000be6f0 0: 0x000be6ff -> 0x000be700 On node 0 totalpages: 779700 DMA zone: 1901 pages, LIFO batch:0 DMA32 zone: 765108 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information SMP: Allowing 4 CPUs, 2 hotplug CPUs Allocating PCI resources starting at c0000000 (gap: bf000000:31000000) PERCPU: Allocating 43424 bytes of per cpu data NR_CPUS: 8, nr_cpu_ids: 4, nr_node_ids 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 767009 Kernel command line: grub_kernel=bzImage-2.6.27.10-012 ro root=/dev/sda6 ide-pci-generic.all-generic-ide vga=6 noisapnp enforcing=0 selinux=0 printk.time=1 log_buf_len=512k [ 0.000000] log_buf_len: 524288 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] TSC: PIT calibration confirmed by PMTIMER. [ 0.000000] TSC: using PMTIMER calibration value [ 0.000000] Detected 2797.147 MHz processor. [ 0.000999] Console: colour VGA+ 80x60 [ 0.000999] console [tty0] enabled [ 0.000999] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000999] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000999] Checking aperture... [ 0.000999] No AGP bridge found [ 0.000999] Memory: 3060364k/3120128k available (4866k kernel code, 57732k reserved, 1889k data, 352k init) [ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated [ 0.000999] hpet clockevent registered [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 5594.29 BogoMIPS (lpj=2797147) [ 0.000999] Security Framework initialized [ 0.000999] SELinux: Disabled at boot. [ 0.000999] Mount-cache hash table entries: 256 [ 0.000999] CPU: Trace cache: 12K uops, L1 D cache: 16K [ 0.000999] CPU: L2 cache: 1024K [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 0 [ 0.000999] CPU0: Thermal monitoring enabled (TM1) [ 0.000999] using mwait in idle threads. [ 0.000999] ACPI: Core revision 20080609 [ 0.010386] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.020966] CPU0: Intel(R) Pentium(R) D CPU 2.80GHz stepping 07 [ 0.021045] Using local APIC timer interrupts. [ 0.022002] APIC timer calibration result 12487291 [ 0.022004] Detected 12.487 MHz APIC timer. [ 0.022204] Booting processor 1/1 ip 6000 [ 0.000999] Initializing CPU#1 [ 0.000999] Calibrating delay using timer specific routine.. 5594.30 BogoMIPS (lpj=2797151) [ 0.000999] CPU: Trace cache: 12K uops, L1 D cache: 16K [ 0.000999] CPU: L2 cache: 1024K [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 1 [ 0.000999] CPU1: Thermal monitoring enabled (TM1) [ 0.000999] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 [ 0.093768] CPU1: Intel(R) Pentium(R) D CPU 2.80GHz stepping 07 [ 0.094107] checking TSC synchronization [CPU#0 -> CPU#1]: [ 0.094999] Measured 3990 cycles TSC warp between CPUs, turning off TSC clock. [ 0.094999] Marking TSC unstable due to check_tsc_sync_source failed [ 0.095013] Brought up 2 CPUs [ 0.095067] Total of 2 processors activated (11188.59 BogoMIPS). [ 0.096046] net_namespace: 1456 bytes [ 0.096181] NET: Registered protocol family 16 [ 0.096548] No dock devices found. [ 0.096731] ACPI: bus type pci registered [ 0.096916] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 127 [ 0.096979] PCI: MCFG area at f0000000 reserved in E820 [ 0.099887] PCI: Using MMCONFIG at f0000000 - f7ffffff [ 0.099943] PCI: Using configuration type 1 for base access [ 0.103432] ACPI: EC: Look up EC in DSDT [ 0.107885] ACPI: Interpreter enabled [ 0.107941] ACPI: (supports S0 S3 S5) [ 0.108070] ACPI: Using IOAPIC for interrupt routing [ 0.115226] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.115422] PCI: 0000:00:02.0 reg 10 32bit mmio: [d0200000, d02fffff] [ 0.115433] PCI: 0000:00:02.0 reg 18 64bit mmio: [c0000000, cfffffff] [ 0.115438] PCI: 0000:00:02.0 reg 20 io port: [2410, 2417] [ 0.115483] PCI: 0000:00:03.0 reg 10 64bit mmio: [d0326100, d032610f] [ 0.115513] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold [ 0.115573] pci 0000:00:03.0: PME# disabled [ 0.115685] PCI: 0000:00:19.0 reg 10 32bit mmio: [d0300000, d031ffff] [ 0.115692] PCI: 0000:00:19.0 reg 14 32bit mmio: [d0324000, d0324fff] [ 0.115699] PCI: 0000:00:19.0 reg 18 io port: [20e0, 20ff] [ 0.115731] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 0.115791] pci 0000:00:19.0: PME# disabled [ 0.115886] PCI: 0000:00:1a.0 reg 20 io port: [20c0, 20df] [ 0.115936] PCI: 0000:00:1a.1 reg 20 io port: [20a0, 20bf] [ 0.115993] PCI: 0000:00:1a.7 reg 10 32bit mmio: [d0325c00, d0325fff] [ 0.116045] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 0.116105] pci 0000:00:1a.7: PME# disabled [ 0.116190] PCI: 0000:00:1b.0 reg 10 64bit mmio: [d0320000, d0323fff] [ 0.116229] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 0.116288] pci 0000:00:1b.0: PME# disabled [ 0.116390] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.116450] pci 0000:00:1c.0: PME# disabled [ 0.116549] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 0.116609] pci 0000:00:1c.1: PME# disabled [ 0.116710] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.116770] pci 0000:00:1c.2: PME# disabled [ 0.116869] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold [ 0.116929] pci 0000:00:1c.3: PME# disabled [ 0.117035] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 0.117095] pci 0000:00:1c.4: PME# disabled [ 0.117184] PCI: 0000:00:1d.0 reg 20 io port: [2080, 209f] [ 0.117236] PCI: 0000:00:1d.1 reg 20 io port: [2060, 207f] [ 0.117285] PCI: 0000:00:1d.2 reg 20 io port: [2040, 205f] [ 0.117343] PCI: 0000:00:1d.7 reg 10 32bit mmio: [d0325800, d0325bff] [ 0.117391] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.117451] pci 0000:00:1d.7: PME# disabled [ 0.117620] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO [ 0.117703] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO [ 0.117805] PCI: 0000:00:1f.2 reg 10 io port: [2408, 240f] [ 0.117811] PCI: 0000:00:1f.2 reg 14 io port: [241c, 241f] [ 0.117817] PCI: 0000:00:1f.2 reg 18 io port: [2400, 2407] [ 0.117823] PCI: 0000:00:1f.2 reg 1c io port: [2418, 241b] [ 0.117829] PCI: 0000:00:1f.2 reg 20 io port: [2020, 203f] [ 0.117835] PCI: 0000:00:1f.2 reg 24 32bit mmio: [d0325000, d03257ff] [ 0.117858] pci 0000:00:1f.2: PME# supported from D3hot [ 0.117915] pci 0000:00:1f.2: PME# disabled [ 0.117982] PCI: 0000:00:1f.3 reg 10 32bit mmio: [d0326000, d03260ff] [ 0.118005] PCI: 0000:00:1f.3 reg 20 io port: [2000, 201f] [ 0.118119] PCI: 0000:02:00.0 reg 10 io port: [1018, 101f] [ 0.118128] PCI: 0000:02:00.0 reg 14 io port: [1024, 1027] [ 0.118138] PCI: 0000:02:00.0 reg 18 io port: [1010, 1017] [ 0.118147] PCI: 0000:02:00.0 reg 1c io port: [1020, 1023] [ 0.118155] PCI: 0000:02:00.0 reg 20 io port: [1000, 100f] [ 0.118163] PCI: 0000:02:00.0 reg 24 32bit mmio: [d0100000, d01001ff] [ 0.118196] pci 0000:02:00.0: supports D1 [ 0.118198] pci 0000:02:00.0: PME# supported from D0 D1 D3hot [ 0.118258] pci 0000:02:00.0: PME# disabled [ 0.118342] PCI: bridge 0000:00:1c.1 io port: [1000, 1fff] [ 0.118346] PCI: bridge 0000:00:1c.1 32bit mmio: [d0100000, d01fffff] [ 0.118528] PCI: 0000:06:03.0 reg 10 32bit mmio: [d0004000, d00047ff] [ 0.118535] PCI: 0000:06:03.0 reg 14 32bit mmio: [d0000000, d0003fff] [ 0.118577] pci 0000:06:03.0: supports D1 [ 0.118579] pci 0000:06:03.0: supports D2 [ 0.118581] pci 0000:06:03.0: PME# supported from D0 D1 D2 D3hot [ 0.118641] pci 0000:06:03.0: PME# disabled [ 0.118729] pci 0000:00:1e.0: transparent bridge [ 0.118786] PCI: bridge 0000:00:1e.0 32bit mmio: [d0000000, d00fffff] [ 0.118819] bus 00 -> node 0 [ 0.118827] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.119411] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 0.119837] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 0.120010] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 0.120182] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT] [ 0.120350] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT] [ 0.120520] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 0.128442] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12) [ 0.128871] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12) [ 0.129300] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12) [ 0.129736] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12) [ 0.130147] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *9 10 11 12) [ 0.130573] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12) [ 0.131019] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12) [ 0.131447] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12) [ 0.132038] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.132141] pnp: PnP ACPI init [ 0.132201] ACPI: bus type pnp registered [ 0.136720] pnp: PnP ACPI: found 13 devices [ 0.136774] ACPI: ACPI bus type pnp unregistered [ 0.137119] SCSI subsystem initialized [ 0.137249] libata version 3.00 loaded. [ 0.137498] usbcore: registered new interface driver usbfs [ 0.137664] usbcore: registered new interface driver hub [ 0.137782] usbcore: registered new device driver usb [ 0.138073] PCI: Using ACPI for IRQ routing [ 0.145035] PCI-GART: No AMD northbridge found. [ 0.145093] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.145236] hpet0: 3 64-bit timers, 14318180 Hz [ 0.146051] ACPI: RTC can wake from S4 [ 0.147015] Switched to high resolution mode on CPU 0 [ 0.147584] Switched to high resolution mode on CPU 1 [ 0.149028] system 00:01: iomem range 0xf0000000-0xf7ffffff could not be reserved [ 0.150693] system 00:01: iomem range 0xfed13000-0xfed13fff has been reserved [ 0.150755] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved [ 0.150817] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved [ 0.150878] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved [ 0.150940] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 0.151007] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved [ 0.151070] system 00:01: iomem range 0xfed45000-0xfed99fff has been reserved [ 0.151134] system 00:01: iomem range 0xc0000-0xdffff has been reserved [ 0.151194] system 00:01: iomem range 0xe0000-0xfffff could not be reserved [ 0.151265] system 00:06: ioport range 0x500-0x53f has been reserved [ 0.151325] system 00:06: ioport range 0x400-0x47f has been reserved [ 0.151384] system 00:06: ioport range 0x360-0x361 has been reserved [ 0.151443] system 00:06: ioport range 0x680-0x6ff has been reserved [ 0.151508] system 00:07: iomem range 0xfed40000-0xfed44fff has been reserved [ 0.156731] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 [ 0.156790] pci 0000:00:1c.0: IO window: disabled [ 0.156847] pci 0000:00:1c.0: MEM window: disabled [ 0.156904] pci 0000:00:1c.0: PREFETCH window: disabled [ 0.156964] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 [ 0.157029] pci 0000:00:1c.1: IO window: 0x1000-0x1fff [ 0.157088] pci 0000:00:1c.1: MEM window: 0xd0100000-0xd01fffff [ 0.157150] pci 0000:00:1c.1: PREFETCH window: disabled [ 0.157210] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:03 [ 0.157267] pci 0000:00:1c.2: IO window: disabled [ 0.157324] pci 0000:00:1c.2: MEM window: disabled [ 0.157380] pci 0000:00:1c.2: PREFETCH window: disabled [ 0.157440] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:04 [ 0.157497] pci 0000:00:1c.3: IO window: disabled [ 0.157554] pci 0000:00:1c.3: MEM window: disabled [ 0.157610] pci 0000:00:1c.3: PREFETCH window: disabled [ 0.157669] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:05 [ 0.157726] pci 0000:00:1c.4: IO window: disabled [ 0.157783] pci 0000:00:1c.4: MEM window: disabled [ 0.157839] pci 0000:00:1c.4: PREFETCH window: disabled [ 0.157900] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:06 [ 0.157956] pci 0000:00:1e.0: IO window: disabled [ 0.158020] pci 0000:00:1e.0: MEM window: 0xd0000000-0xd00fffff [ 0.158081] pci 0000:00:1e.0: PREFETCH window: disabled [ 0.158154] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.158217] pci 0000:00:1c.0: setting latency timer to 64 [ 0.158226] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 0.158288] pci 0000:00:1c.1: setting latency timer to 64 [ 0.158297] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.158358] pci 0000:00:1c.2: setting latency timer to 64 [ 0.158367] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.158428] pci 0000:00:1c.3: setting latency timer to 64 [ 0.158436] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.158497] pci 0000:00:1c.4: setting latency timer to 64 [ 0.158504] pci 0000:00:1e.0: setting latency timer to 64 [ 0.158508] bus: 00 index 0 io port: [0, ffff] [ 0.158561] bus: 00 index 1 mmio: [0, ffffffffffffffff] [ 0.158617] bus: 01 index 0 mmio: [0, 0] [ 0.158668] bus: 01 index 1 mmio: [0, 0] [ 0.158719] bus: 01 index 2 mmio: [0, 0] [ 0.158770] bus: 01 index 3 mmio: [0, 0] [ 0.158822] bus: 02 index 0 io port: [1000, 1fff] [ 0.158876] bus: 02 index 1 mmio: [d0100000, d01fffff] [ 0.158931] bus: 02 index 2 mmio: [0, 0] [ 0.158982] bus: 02 index 3 mmio: [0, 0] [ 0.159042] bus: 03 index 0 mmio: [0, 0] [ 0.159094] bus: 03 index 1 mmio: [0, 0] [ 0.159148] bus: 03 index 2 mmio: [0, 0] [ 0.159199] bus: 03 index 3 mmio: [0, 0] [ 0.159250] bus: 04 index 0 mmio: [0, 0] [ 0.159301] bus: 04 index 1 mmio: [0, 0] [ 0.159353] bus: 04 index 2 mmio: [0, 0] [ 0.159404] bus: 04 index 3 mmio: [0, 0] [ 0.159455] bus: 05 index 0 mmio: [0, 0] [ 0.159506] bus: 05 index 1 mmio: [0, 0] [ 0.159557] bus: 05 index 2 mmio: [0, 0] [ 0.159608] bus: 05 index 3 mmio: [0, 0] [ 0.159660] bus: 06 index 0 mmio: [0, 0] [ 0.159711] bus: 06 index 1 mmio: [d0000000, d00fffff] [ 0.159766] bus: 06 index 2 mmio: [0, 0] [ 0.159817] bus: 06 index 3 io port: [0, ffff] [ 0.159870] bus: 06 index 4 mmio: [0, ffffffffffffffff] [ 0.159964] NET: Registered protocol family 2 [ 0.171021] random: early call rand_initialize [ 0.171075] random: rand_initialize starting [ 0.171128] random: rand_initialize OK (random_debug=0/debug_max=31 POOLBITS=8192) [ 0.171165] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.171781] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 0.174108] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.174735] TCP: Hash tables configured (established 262144 bind 65536) [ 0.174799] TCP reno registered [ 0.177134] NET: Registered protocol family 1 [ 0.178331] IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx> [ 0.178922] audit: initializing netlink socket (disabled) [ 0.178995] type=2000 audit(1229993307.178:1): initialized [ 0.179399] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.179612] VFS: Disk quotas dquot_6.5.1 [ 0.179683] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.179882] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 0.180227] SGI XFS Quota Management subsystem [ 0.180289] msgmni has been set to 5978 [ 0.180450] io scheduler noop registered [ 0.180503] io scheduler anticipatory registered (default) [ 0.180559] io scheduler deadline registered [ 0.180634] io scheduler cfq registered [ 0.180697] pci 0000:00:02.0: Boot video device [ 0.181173] pcieport-driver 0000:00:1c.0: setting latency timer to 64 [ 0.181208] pcieport-driver 0000:00:1c.0: found MSI capability [ 0.181302] pci_express 0000:00:1c.0:pcie00: allocate port service [ 0.181356] pci_express 0000:00:1c.0:pcie02: allocate port service [ 0.181405] pci_express 0000:00:1c.0:pcie03: allocate port service [ 0.181508] pcieport-driver 0000:00:1c.1: setting latency timer to 64 [ 0.181542] pcieport-driver 0000:00:1c.1: found MSI capability [ 0.181631] pci_express 0000:00:1c.1:pcie00: allocate port service [ 0.181679] pci_express 0000:00:1c.1:pcie02: allocate port service [ 0.181726] pci_express 0000:00:1c.1:pcie03: allocate port service [ 0.181826] pcieport-driver 0000:00:1c.2: setting latency timer to 64 [ 0.181860] pcieport-driver 0000:00:1c.2: found MSI capability [ 0.181949] pci_express 0000:00:1c.2:pcie00: allocate port service [ 0.181999] pci_express 0000:00:1c.2:pcie02: allocate port service [ 0.182051] pci_express 0000:00:1c.2:pcie03: allocate port service [ 0.182162] pcieport-driver 0000:00:1c.3: setting latency timer to 64 [ 0.182196] pcieport-driver 0000:00:1c.3: found MSI capability [ 0.182286] pci_express 0000:00:1c.3:pcie00: allocate port service [ 0.182333] pci_express 0000:00:1c.3:pcie02: allocate port service [ 0.182383] pci_express 0000:00:1c.3:pcie03: allocate port service [ 0.182483] pcieport-driver 0000:00:1c.4: setting latency timer to 64 [ 0.182517] pcieport-driver 0000:00:1c.4: found MSI capability [ 0.182606] pci_express 0000:00:1c.4:pcie00: allocate port service [ 0.182655] pci_express 0000:00:1c.4:pcie02: allocate port service [ 0.182706] pci_express 0000:00:1c.4:pcie03: allocate port service [ 0.182901] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.182959] cpcihp_zt5550: ZT5550 CompactPCI Hot Plug Driver version: 0.2 [ 0.183085] cpcihp_generic: Generic port I/O CompactPCI Hot Plug Driver version: 0.1 [ 0.183172] cpcihp_generic: not configured, disabling. [ 0.183450] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.183574] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 0.184120] processor ACPI0007:00: registered as cooling_device0 [ 0.184186] ACPI: Processor [CPU0] (supports 8 throttling states) [ 0.184407] processor ACPI0007:01: registered as cooling_device1 [ 0.184470] ACPI: Processor [CPU1] (supports 8 throttling states) [ 0.190025] random: skipping rand_initialize: already initialized [ 0.190233] hpet_resources: 0xfed00000 is busy [ 0.190423] Linux agpgart interface v0.103 [ 0.190495] agpgart-intel 0000:00:00.0: Intel 965Q Chipset [ 0.190948] agpgart-intel 0000:00:00.0: detected 7676K stolen memory [ 0.206738] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000 [ 0.207051] [drm] Initialized drm 1.1.0 20060810 [ 0.207108] Serial: 8250/16550 driver4 ports, IRQ sharing enabled [ 0.451293] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.451905] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.454042] brd: module loaded [ 0.454177] Uniform Multi-Platform E-IDE driver [ 0.455430] ide_pci_generic 0000:02:00.0: IDE controller (0x11ab:0x6101 rev 0xb1) [ 0.455523] PCI_IDE 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.455599] ide_pci_generic 0000:02:00.0: 100% native mode on irq 17 [ 0.455663] ide0: BM-DMA at 0x1000-0x1007 [ 0.455721] ide1: BM-DMA at 0x1008-0x100f [ 0.455775] Probing IDE interface ide0... [ 0.719432] hda: ST3160023A, ATA DISK drive [ 1.331205] Probing IDE interface ide1... [ 3.074211] ide0 at 0x1018-0x101f,0x1026 on irq 17 [ 3.074314] isa bounce pool size: 16 pages [ 3.074379] ide1 at 0x1010-0x1017,0x1022 on irq 17 [ 3.074587] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports [ 3.074683] Probing IDE interface ide2... [ 3.587191] Probing IDE interface ide3... [ 4.100204] ide2 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 4.100297] ide3 at 0x170-0x177,0x376 on irq 15 [ 4.100506] hda: max request size: 512KiB [ 4.101076] hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63 [ 4.101354] hda: cache flushes supported [ 4.101474] hda: hda1 hda2 < hda5 hda6 > [ 4.126369] ide-floppy driver 1.00 [ 4.127151] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded [ 4.127301] stex: Promise SuperTrak EX Driver version: 3.6.0000.1 [ 4.127416] st: Version 20080504, fixed bufsize 32768, s/g segs 256 [ 4.129096] Driver 'st' needs updating - please use bus_type methods [ 4.129204] osst :I: Tape driver with OnStream support version 0.99.4 [ 4.129205] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $ [ 4.129362] Driver 'osst' needs updating - please use bus_type methods [ 4.129508] Driver 'sd' needs updating - please use bus_type methods [ 4.129608] Driver 'sr' needs updating - please use bus_type methods [ 4.129790] ahci 0000:00:1f.2: version 3.0 [ 4.129806] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.129987] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 4.130079] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pio slum part ems [ 4.130166] ahci 0000:00:1f.2: setting latency timer to 64 [ 4.130522] scsi0 : ahci [ 4.130778] scsi1 : ahci [ 4.130966] scsi2 : ahci [ 4.131164] scsi3 : ahci [ 4.131364] scsi4 : ahci [ 4.131550] scsi5 : ahci [ 4.131835] ata1: SATA max UDMA/133 abar m2048@0xd0325000 port 0xd0325100 irq 506 [ 4.131917] ata2: SATA max UDMA/133 abar m2048@0xd0325000 port 0xd0325180 irq 506 [ 4.131997] ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 506 [ 4.132087] ata4: SATA max UDMA/133 irq_stat 0x00000040, connection status changed irq 506 [ 4.132171] ata5: SATA max UDMA/133 abar m2048@0xd0325000 port 0xd0325300 irq 506 [ 4.132251] ata6: SATA max UDMA/133 abar m2048@0xd0325000 port 0xd0325380 irq 506 [ 4.437142] ata1: SATA link down (SStatus 0 SControl 300) [ 4.742139] ata2: SATA link down (SStatus 0 SControl 300) [ 5.465141] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.506396] ata3.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 5.506455] ata3.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 5.564704] ata3.00: configured for UDMA/133 [ 6.287018] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 6.288219] ata4.00: ATAPI: HL-DT-STDVD-RAM GH22NS30, 1.01, max UDMA/100 [ 6.289677] ata4.00: configured for UDMA/100 [ 6.594016] ata5: SATA link down (SStatus 0 SControl 300) [ 6.899016] ata6: SATA link down (SStatus 0 SControl 300) [ 6.899178] scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 [ 6.899523] sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB) [ 6.899601] sd 2:0:0:0: [sda] Write Protect is off [ 6.899656] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.899687] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.899850] sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB) [ 6.899925] sd 2:0:0:0: [sda] Write Protect is off [ 6.899981] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.900019] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.900104] sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 > [ 6.964811] sd 2:0:0:0: [sda] Attached SCSI disk [ 6.965017] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 6.966178] scsi 3:0:0:0: CD-ROM HL-DT-ST DVD-RAM GH22NS30 1.01 PQ: 0 ANSI: 5 [ 6.969584] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 6.969666] Uniform CD-ROM driver Revision: 3.20 [ 6.969881] sr 3:0:0:0: Attached scsi CD-ROM sr0 [ 6.970018] sr 3:0:0:0: Attached scsi generic sg1 type 5 [ 6.972031] PNP: No PS/2 controller found. Probing ports directly. [ 6.974979] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 6.975045] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 6.975172] mice: PS/2 mouse device common for all mice [ 6.975423] EDAC MC: Ver: 2.1.0 Dec 18 2008 [ 6.976054] usbcore: registered new interface driver hiddev [ 6.976164] usbcore: registered new interface driver usbhid [ 6.976223] usbhid: v2.6:USB HID core driver [ 6.976358] TCP bic registered [ 6.976408] Initializing XFRM netlink socket [ 6.976528] NET: Registered protocol family 10 [ 6.976761] lo: Disabled Privacy Extensions [ 6.976850] IPv6 over IPv4 tunneling driver [ 6.977104] sit0: Disabled Privacy Extensions [ 6.977175] NET: Registered protocol family 17 [ 6.977576] drivers/rtc/hctosys.c: unable to open rtc device (rtc) [ 7.684230] md: Autodetecting RAID arrays. [ 7.684284] md: Scanned 0 and added 0 devices. [ 7.684336] md: autorun ... [ 7.684384] md: ... autorun DONE. [ 7.729403] XFS mounting filesystem sda6 [ 7.779501] Ending clean XFS mount for filesystem: sda6 [ 7.779543] VFS: Mounted root (xfs filesystem) readonly. [ 7.779616] Freeing unused kernel memory: 352k freed [ 7.779831] Write protecting the kernel read-only data: 6384k [ 10.137155] USB Universal Host Controller Interface driver v3.0 [ 10.137238] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 10.137248] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 10.137252] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 10.137315] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 10.137353] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020c0 [ 10.137487] usb usb1: configuration #1 chosen from 1 choice [ 10.137526] hub 1-0:1.0: USB hub found [ 10.137535] hub 1-0:1.0: 2 ports detected [ 10.208233] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 10.221197] ACPI: Power Button (FF) [PWRF] [ 10.221278] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 10.232084] ACPI: Sleep Button (CM) [SLPB] [ 10.238269] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.238273] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.238276] usb usb1: Product: UHCI Host Controller [ 10.238278] usb usb1: Manufacturer: Linux 2.6.27.10 uhci_hcd [ 10.238280] usb usb1: SerialNumber: 0000:00:1a.0 [ 10.238320] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 10.238332] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 10.238336] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 10.238372] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 [ 10.238411] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020a0 [ 10.238523] usb usb2: configuration #1 chosen from 1 choice [ 10.238562] hub 2-0:1.0: USB hub found [ 10.238570] hub 2-0:1.0: 2 ports detected [ 10.252393] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6 [ 10.252397] e1000e: Copyright (c) 1999-2008 Intel Corporation. [ 10.324060] parport_pc 00:09: reported by Plug and Play ACPI [ 10.324172] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] [ 10.382955] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after [ 10.440188] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.440193] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.440196] usb usb2: Product: UHCI Host Controller [ 10.440199] usb usb2: Manufacturer: Linux 2.6.27.10 uhci_hcd [ 10.440201] usb usb2: SerialNumber: 0000:00:1a.1 [ 10.440339] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 10.440349] e1000e 0000:00:19.0: setting latency timer to 64 [ 10.542029] usb 2-1: new low speed USB device using uhci_hcd and address 2 [ 10.568144] iTCO_vendor_support: vendor-support=0 [ 10.590461] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) [ 10.590570] iTCO_wdt: Found a ICH8DO TCO device (Version=2, TCOBASE=0x0460) [ 10.590633] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 10.624403] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:19:d1:00:5f:01 [ 10.624407] 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 10.624433] 0000:00:19.0: eth0: MAC: 5, PHY: 6, PBA No: ffffff-0ff [ 10.624536] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 10.624556] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 10.624560] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 10.624604] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3 [ 10.628505] ehci_hcd 0000:00:1a.7: debug port 1 [ 10.628512] ehci_hcd 0000:00:1a.7: cache line size of 128 is not supported [ 10.628531] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xd0325c00 [ 10.656017] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 10.656158] usb usb3: configuration #1 chosen from 1 choice [ 10.656198] hub 3-0:1.0: USB hub found [ 10.656209] hub 3-0:1.0: 4 ports detected [ 10.858185] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 10.858189] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.858192] usb usb3: Product: EHCI Host Controller [ 10.858195] usb usb3: Manufacturer: Linux 2.6.27.10 ehci_hcd [ 10.858198] usb usb3: SerialNumber: 0000:00:1a.7 [ 10.858281] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 10.858293] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 10.858297] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 10.858335] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4 [ 10.858375] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080 [ 10.858517] usb usb4: configuration #1 chosen from 1 choice [ 10.858557] hub 4-0:1.0: USB hub found [ 10.858567] hub 4-0:1.0: 2 ports detected [ 10.867863] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 10.867891] rtc0: alarms up to one month, hpet irqs [ 10.894540] input: PC Speaker as /devices/platform/pcspkr/input/input2 [ 10.959234] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.959238] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.959242] usb usb4: Product: UHCI Host Controller [ 10.959245] usb usb4: Manufacturer: Linux 2.6.27.10 uhci_hcd [ 10.959247] usb usb4: SerialNumber: 0000:00:1d.0 [ 10.959312] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 10.959324] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 10.959328] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 10.959365] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5 [ 10.959404] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 [ 10.959519] usb usb5: configuration #1 chosen from 1 choice [ 10.959558] hub 5-0:1.0: USB hub found [ 10.959566] hub 5-0:1.0: 2 ports detected [ 11.058023] usb 2-1: device not accepting address 2, error -71 [ 11.109097] hub 2-0:1.0: unable to enumerate USB device on port 1 [ 11.161180] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 11.161184] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.161187] usb usb5: Product: UHCI Host Controller [ 11.161189] usb usb5: Manufacturer: Linux 2.6.27.10 uhci_hcd [ 11.161191] usb usb5: SerialNumber: 0000:00:1d.1 [ 11.161871] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 11.161882] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 11.161886] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 11.161930] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6 [ 11.161957] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 [ 11.162090] usb usb6: configuration #1 chosen from 1 choice [ 11.162129] hub 6-0:1.0: USB hub found [ 11.162138] hub 6-0:1.0: 2 ports detected [ 11.260240] ppdev: user-space parallel port driver [ 11.263192] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 11.263196] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.263199] usb usb6: Product: UHCI Host Controller [ 11.263202] usb usb6: Manufacturer: Linux 2.6.27.10 uhci_hcd [ 11.263204] usb usb6: SerialNumber: 0000:00:1d.2 [ 11.264073] usb 5-1: new low speed USB device using uhci_hcd and address 2 [ 11.264125] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 11.264160] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 11.264166] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 11.264232] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7 [ 11.268153] ehci_hcd 0000:00:1d.7: debug port 1 [ 11.268161] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported [ 11.268314] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd0325800 [ 11.278147] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 11.278320] usb usb7: configuration #1 chosen from 1 choice [ 11.278365] hub 7-0:1.0: USB hub found [ 11.278376] hub 7-0:1.0: 6 ports detected [ 11.329055] hub 5-0:1.0: unable to enumerate USB device on port 1 [ 11.480329] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002 [ 11.480334] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.480337] usb usb7: Product: EHCI Host Controller [ 11.480339] usb usb7: Manufacturer: Linux 2.6.27.10 ehci_hcd [ 11.480341] usb usb7: SerialNumber: 0000:00:1d.7 [ 11.481409] ohci1394 0000:06:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 11.530969] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 11.532278] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[d0004000-d00047ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 11.684028] usb 2-1: new low speed USB device using uhci_hcd and address 4 [ 11.843587] usb 2-1: configuration #1 chosen from 1 choice [ 11.859570] hiddev96: USB HID v1.11 Device [OMRON 87XXUPS] on usb-0000:00:1a.1-1 [ 11.859711] usb 2-1: New USB device found, idVendor=06da, idProduct=0003 [ 11.859715] usb 2-1: New USB device strings: Mfr=3, Product=1, SerialNumber=0 [ 11.859717] usb 2-1: Product: 87XXUPS [ 11.859719] usb 2-1: Manufacturer: OMRON [ 12.067425] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 12.067501] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 12.220019] usb 5-1: new low speed USB device using uhci_hcd and address 3 [ 12.293507] TCP cubic registered [ 12.431112] md: Autodetecting RAID arrays. [ 12.431117] md: Scanned 0 and added 0 devices. [ 12.431119] md: autorun ... [ 12.431121] md: ... autorun DONE. [ 12.477788] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@xxxxxxxxxx [ 12.493594] usb 5-1: configuration #1 chosen from 1 choice [ 12.548033] input: Chicony Saitek Eclipse II Keyboard as /devices/pci0000:00/0000:00:1d.1/usb5/5-1/5-1:1.0/input/input3 [ 12.557084] input: USB HID v1.11 Keyboard [Chicony Saitek Eclipse II Keyboard] on usb-0000:00:1d.1-1 [ 12.703154] input: Chicony Saitek Eclipse II Keyboard as /devices/pci0000:00/0000:00:1d.1/usb5/5-1/5-1:1.1/input/input4 [ 12.716252] input,hiddev97: USB HID v1.11 Device [Chicony Saitek Eclipse II Keyboard] on usb-0000:00:1d.1-1 [ 12.716397] usb 5-1: New USB device found, idVendor=06a3, idProduct=8021 [ 12.716400] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 12.716403] usb 5-1: Product: Saitek Eclipse II Keyboard [ 12.716406] usb 5-1: Manufacturer: Chicony [ 12.788736] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0090270001b66bbe] [ 12.850899] loop: loaded (max 8 devices) [ 12.923146] usb 5-2: new full speed USB device using uhci_hcd and address 4 [ 13.081593] usb 5-2: configuration #1 chosen from 1 choice [ 13.089745] input: Tempest Habu Mouse as /devices/pci0000:00/0000:00:1d.1/usb5/5-2/5-2:1.0/input/input5 [ 13.104211] input: USB HID v10.01 Mouse [Tempest Habu Mouse] on usb-0000:00:1d.1-2 [ 13.109023] input: Tempest Habu Mouse as /devices/pci0000:00/0000:00:1d.1/usb5/5-2/5-2:1.1/input/input6 [ 13.121780] input: USB HID v10.01 Keyboard [Tempest Habu Mouse] on usb-0000:00:1d.1-2 [ 13.122744] usb 5-2: New USB device found, idVendor=1532, idProduct=0009 [ 13.122749] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 13.122752] usb 5-2: Product: Habu Mouse [ 13.122755] usb 5-2: Manufacturer: Tempest [ 13.436105] XFS mounting filesystem sda1 [ 13.478935] Ending clean XFS mount for filesystem: sda1 [ 13.538792] XFS mounting filesystem sda7 [ 13.697341] Ending clean XFS mount for filesystem: sda7 [ 13.756435] XFS mounting filesystem sda8 [ 13.822554] Ending clean XFS mount for filesystem: sda8 [ 13.924133] XFS mounting filesystem sda10 [ 14.028436] Ending clean XFS mount for filesystem: sda10 [ 20.937478] Adding 3911784k swap on /dev/loop6. Priority:10 extents:1 across:3911784k