Hi, I have a laptop with an ICH6M SATA Controller and a Hitachi hard drive. While it worked well using the ahci module and Linux 2.6.25, it get randomly 'stuck' for several seconds to several minutes with 2.6.26-rc8. Successive errors progressively reduce the ATA link speed. Passing the libata.noacpi parameter is an effective workaround. Please note that it's not the first time i have this kind of issue, see: http://marc.info/?l=linux-ide&m=117305595312399&w=2 This was found to be a bad interaction between my _GTF taskfile, which enable the "Enable Device-Initiated Interface Power State Transitions" feature, and NCQ. The driver was later NCQ blacklisted to correct the problem. Device detection: [ 0.567684] ahci 0000:00:1f.2: version 3.0 [ 1.568027] ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0x5 impl IDE mode [ 1.568091] ahci 0000:00:1f.2: flags: 64bit ncq pm led slum part [ 1.568695] ata1: SATA max UDMA/133 abar m1024@0xb8000c00 port 0xb8000d00 irq 19 [ 1.873016] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.874045] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1.875000] ata1.00: ATA-7: HTS541010G9SA00, MBZOC60D, max UDMA/100 [ 1.875000] ata1.00: 195371568 sectors, multi 0: LBA48 NCQ (not used) [ 1.875000] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1.875000] ata1.00: configured for UDMA/100 Typical error: [ 499.178040] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 499.178105] ata1.00: cmd ca/00:3e:76:45:81/00:00:00:00:00/e1 tag 0 dma 31744 out [ 499.178106] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 499.178168] ata1.00: status: { DRDY } [ 499.178220] ata1: hard resetting link [ 499.942034] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 499.943540] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 499.946056] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 499.947174] ata1.00: configured for UDMA/100 [ 499.947174] ata1: EH complete Full dmesg is attached. -- Mathieu Bérard
[ 0.000000] Linux version 2.6.26-rc8 (mathieu@manwe) (gcc version 4.3.1 (Ubuntu 4.3.1-3ubuntu1) ) #1 PREEMPT Mon Jun 30 01:12:00 CEST 2008 [ 0.000000] PAT disabled. Not yet verified on this CPU type. [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved) [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fee0000 (usable) [ 0.000000] BIOS-e820: 000000003fee0000 - 000000003feea000 (ACPI data) [ 0.000000] BIOS-e820: 000000003feea000 - 000000003ff00000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved) [ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved) [ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved) [ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) [ 0.000000] 126MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] Entering add_active_range(0, 0, 261856) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 261856 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 261856 [ 0.000000] On node 0 totalpages: 261856 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 254 pages used for memmap [ 0.000000] HighMem zone: 32226 pages, LIFO batch:7 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP 000F6950, 0014 (r0 TOSCPL) [ 0.000000] ACPI: RSDT 3FEE1FCA, 0044 (r1 TOSCPL RSDT 6040000 LTP 0) [ 0.000000] ACPI: APIC 3FEE9E88, 0068 (r1 INTEL ALVISO 6040000 LOHR 5F) [ 0.000000] ACPI: FACP 3FEE9EF0, 0074 (r1 TOSCPL ALVISO 6040000 LOHR 32) [ 0.000000] ACPI: DSDT 3FEE2A72, 7416 (r1 TOSCPL ALVISO 6040000 MSFT 3000000) [ 0.000000] ACPI: FACS 3FEFAFC0, 0040 [ 0.000000] ACPI: BOOT 3FEE9FD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) [ 0.000000] ACPI: MCFG 3FEE9F9C, 003C (r1 INTEL ALVISO 6040000 LOHR 5F) [ 0.000000] ACPI: SSDT 3FEE2840, 022E (r1 SataRe SataAhci 1000 INTL 20030224) [ 0.000000] ACPI: SSDT 3FEE2405, 022B (r1 PmRef Cpu0Ist 3000 INTL 20030224) [ 0.000000] ACPI: SSDT 3FEE2227, 01DE (r1 PmRef Cpu0Cst 3001 INTL 20030224) [ 0.000000] ACPI: SSDT 3FEE200E, 0219 (r1 PmRef CpuPm 3000 INTL 20030224) [ 0.000000] ACPI: DMI detected: Toshiba [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000 [ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000 [ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000 [ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259810 [ 0.000000] Kernel command line: root=UUID=8aa84942-b9a7-4622-a512-c180ce3095db ro savedefault single [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] Preemptible RCU implementation. [ 0.000000] CPU 0 irqstacks, hard=c03b8000 soft=c03b7000 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 1729.103 MHz processor. [ 0.000999] Console: colour VGA+ 80x25 [ 0.000999] console [tty0] enabled [ 0.000999] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000999] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000999] Memory: 1030072k/1047424k available (1773k kernel code, 16608k reserved, 799k data, 188k init, 129920k highmem) [ 0.000999] virtual kernel memory layout: [ 0.000999] fixmap : 0xfffa8000 - 0xfffff000 ( 348 kB) [ 0.000999] pkmap : 0xffa00000 - 0xffc00000 (2048 kB) [ 0.000999] vmalloc : 0xf8800000 - 0xff9fe000 ( 113 MB) [ 0.000999] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 0.000999] .init : 0xc0385000 - 0xc03b4000 ( 188 kB) [ 0.000999] .data : 0xc02bb5f8 - 0xc0383538 ( 799 kB) [ 0.000999] .text : 0xc0100000 - 0xc02bb5f8 (1773 kB) [ 0.000999] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated [ 0.000999] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.061050] Calibrating delay using timer specific routine.. 3460.32 BogoMIPS (lpj=1730163) [ 0.061163] Mount-cache hash table entries: 512 [ 0.061341] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.061427] CPU: L2 cache: 2048K [ 0.061476] Intel machine check architecture supported. [ 0.061529] Intel machine check reporting enabled on CPU#0. [ 0.061586] CPU: Intel(R) Pentium(R) M processor 1.73GHz stepping 08 [ 0.061711] Checking 'hlt' instruction... OK. [ 0.065337] Freeing SMP alternatives: 0k freed [ 0.065387] ACPI: Core revision 20080321 [ 0.077988] ENABLING IO-APIC IRQs [ 0.077988] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.087986] net_namespace: 480 bytes [ 0.087986] NET: Registered protocol family 16 [ 0.087986] ACPI: bus type pci registered [ 0.087986] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.087986] PCI: MCFG area at e0000000 reserved in E820 [ 0.087986] PCI: Using MMCONFIG for extended config space [ 0.087986] PCI: Using configuration type 1 for base access [ 0.087986] Setting up standard PCI resources [ 0.092423] ACPI: EC: Look up EC in DSDT [ 0.095508] ACPI: Interpreter enabled [ 0.095558] ACPI: (supports S0 S3 S4 S5) [ 0.095759] ACPI: Using IOAPIC for interrupt routing [ 0.140766] ACPI: EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62 [ 0.140822] ACPI: EC: driver started in poll mode [ 0.140891] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.141686] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 0.141693] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO [ 0.141757] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO [ 0.142803] PCI: Transparent bridge - 0000:00:1e.0 [ 0.142908] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.143252] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT] [ 0.143413] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] [ 0.143566] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] [ 0.143730] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] [ 0.150741] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15) [ 0.151338] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 [ 0.151970] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 [ 0.152604] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15) [ 0.153196] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 [ 0.153830] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15) [ 0.154422] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 [ 0.154976] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15) [ 0.155634] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.155696] pnp: PnP ACPI init [ 0.155747] ACPI: bus type pnp registered [ 0.178303] pnp: PnP ACPI: found 9 devices [ 0.178353] ACPI: ACPI bus type pnp unregistered [ 0.178449] PCI: Using ACPI for IRQ routing [ 0.182234] hpet clockevent registered [ 0.182241] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.182433] hpet0: 3 64-bit timers, 14318180 Hz [ 0.189107] system 00:01: ioport range 0xfe00-0xfe7f has been reserved [ 0.189163] system 00:01: ioport range 0xfe80-0xfeff has been reserved [ 0.189217] system 00:01: ioport range 0xff00-0xff7f has been reserved [ 0.189272] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved [ 0.189334] system 00:01: iomem range 0xf0000000-0xf0003fff could not be reserved [ 0.189395] system 00:01: iomem range 0xf0004000-0xf0004fff could not be reserved [ 0.189457] system 00:01: iomem range 0xf0005000-0xf0005fff could not be reserved [ 0.189519] system 00:01: iomem range 0xf0008000-0xf000bfff could not be reserved [ 0.189581] system 00:01: iomem range 0xfed20000-0xfed8ffff could not be reserved [ 0.189651] system 00:05: ioport range 0x800-0x80f has been reserved [ 0.189705] system 00:05: ioport range 0x1000-0x107f has been reserved [ 0.189758] system 00:05: ioport range 0x1180-0x11bf has been reserved [ 0.189812] system 00:05: ioport range 0x1640-0x164f has been reserved [ 0.219963] PCI: region 0000:06:04.0/9 too large: 0x0000000000000000-0x0000000003ffffff [ 0.220032] PCI: Bridge: 0000:00:01.0 [ 0.220080] IO window: 3000-3fff [ 0.220129] MEM window: 0xb8100000-0xb81fffff [ 0.220181] PREFETCH window: 0x00000000c8000000-0x00000000cfffffff [ 0.220236] PCI: Bridge: 0000:00:1c.0 [ 0.220285] IO window: 4000-4fff [ 0.220336] MEM window: 0xbc000000-0xbfffffff [ 0.220389] PREFETCH window: 0x00000000d0000000-0x00000000d3ffffff [ 0.220447] PCI: Bridge: 0000:00:1c.1 [ 0.220496] IO window: 5000-5fff [ 0.220547] MEM window: 0xc0000000-0xc3ffffff [ 0.220600] PREFETCH window: 0x00000000d4000000-0x00000000d7ffffff [ 0.220661] PCI: Bus 7, cardbus bridge: 0000:06:04.0 [ 0.220711] IO window: 0x00006400-0x000064ff [ 0.220763] IO window: 0x00006800-0x000068ff [ 0.220816] MEM window: 0x50000000-0x53ffffff [ 0.220869] PCI: Bridge: 0000:00:1e.0 [ 0.220918] IO window: 6000-6fff [ 0.220970] MEM window: 0xc4000000-0xc40fffff [ 0.221023] PREFETCH window: disabled. [ 0.221086] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 0.221185] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 0.221205] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17 [ 0.221305] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 0.221326] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16 [ 0.221425] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 0.221438] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 0.221454] ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 0.221559] NET: Registered protocol family 2 [ 0.239044] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.239958] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.240787] TCP bind hash table entries: 65536 (order: 6, 262144 bytes) [ 0.241114] TCP: Hash tables configured (established 131072 bind 65536) [ 0.241169] TCP reno registered [ 0.247066] NET: Registered protocol family 1 [ 0.247241] Unpacking initramfs... done [ 0.479151] Freeing initrd memory: 4484k freed [ 0.479252] Simple Boot Flag at 0x36 set to 0x1 [ 0.479684] highmem bounce pool size: 64 pages [ 0.479743] Total HugeTLB memory allocated, 0 [ 0.480987] msgmni has been set to 1767 [ 0.481151] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.481214] io scheduler noop registered [ 0.481270] io scheduler cfq registered (default) [ 0.481425] pci 0000:01:00.0: Boot video device [ 0.481507] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 0.481535] assign_interrupt_mode Found MSI capability [ 0.481610] Allocate Port Service[0000:00:01.0:pcie00] [ 0.481628] Allocate Port Service[0000:00:01.0:pcie03] [ 0.481675] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 0.481716] assign_interrupt_mode Found MSI capability [ 0.481806] Allocate Port Service[0000:00:1c.0:pcie00] [ 0.481820] Allocate Port Service[0000:00:1c.0:pcie02] [ 0.481833] Allocate Port Service[0000:00:1c.0:pcie03] [ 0.481915] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 0.481956] assign_interrupt_mode Found MSI capability [ 0.482045] Allocate Port Service[0000:00:1c.1:pcie00] [ 0.482060] Allocate Port Service[0000:00:1c.1:pcie02] [ 0.482073] Allocate Port Service[0000:00:1c.1:pcie03] [ 0.483062] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 0.483403] i8042.c: Detected active multiplexing controller, rev 1.1. [ 0.483522] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.483575] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 0.483627] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 0.483678] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 0.483730] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 0.483796] mice: PS/2 mouse device common for all mice [ 0.483867] cpuidle: using governor ladder [ 0.483919] cpuidle: using governor menu [ 0.484282] TCP cubic registered [ 0.484331] Using IPI Shortcut mode [ 0.484418] registered taskstats version 1 [ 0.484726] Freeing unused kernel memory: 188k freed [ 0.487357] input: AT Translated Set 2 keyboard as /class/input/input0 [ 0.552083] No dock devices found. [ 0.558425] SCSI subsystem initialized [ 0.566002] libata version 3.00 loaded. [ 0.567684] ahci 0000:00:1f.2: version 3.0 [ 0.567713] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 [ 0.682859] Switched to high resolution mode on CPU 0 [ 1.568027] ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0x5 impl IDE mode [ 1.568091] ahci 0000:00:1f.2: flags: 64bit ncq pm led slum part [ 1.568146] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 1.568283] scsi0 : ahci [ 1.568398] scsi1 : ahci [ 1.568482] scsi2 : ahci [ 1.568568] scsi3 : ahci [ 1.568695] ata1: SATA max UDMA/133 abar m1024@0xb8000c00 port 0xb8000d00 irq 19 [ 1.568756] ata2: DUMMY [ 1.568803] ata3: SATA max UDMA/133 abar m1024@0xb8000c00 port 0xb8000e00 irq 19 [ 1.568864] ata4: DUMMY [ 1.873016] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.874045] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1.875000] ata1.00: ATA-7: HTS541010G9SA00, MBZOC60D, max UDMA/100 [ 1.875000] ata1.00: 195371568 sectors, multi 0: LBA48 NCQ (not used) [ 1.875000] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1.875000] ata1.00: configured for UDMA/100 [ 2.205015] ata3: SATA link down (SStatus 0 SControl 300) [ 2.227086] scsi 0:0:0:0: Direct-Access ATA HTS541010G9SA00 MBZO PQ: 0 ANSI: 5 [ 2.233881] fuse init (API version 7.9) [ 2.252219] device-mapper: uevent: version 1.0.3 [ 2.252347] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx [ 2.520087] usbcore: registered new interface driver usbfs [ 2.520163] usbcore: registered new interface driver hub [ 2.520470] usbcore: registered new device driver usb [ 2.521427] USB Universal Host Controller Interface driver v3.0 [ 2.521525] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23 [ 2.521630] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 2.521634] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.521771] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 2.521863] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800 [ 2.521984] usb usb1: configuration #1 chosen from 1 choice [ 2.522064] hub 1-0:1.0: USB hub found [ 2.522116] hub 1-0:1.0: 2 ports detected [ 2.562082] 8139too Fast Ethernet driver 0.9.28 [ 2.623248] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23 [ 2.623368] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 2.623372] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.623444] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 2.627410] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.627465] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 2.627472] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb8000000 [ 2.637010] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 2.637157] usb usb2: configuration #1 chosen from 1 choice [ 2.637237] hub 2-0:1.0: USB hub found [ 2.637291] hub 2-0:1.0: 8 ports detected [ 2.738128] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 2.738240] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 2.738244] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.738317] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.738406] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820 [ 2.738536] usb usb3: configuration #1 chosen from 1 choice [ 2.738614] hub 3-0:1.0: USB hub found [ 2.738667] hub 3-0:1.0: 2 ports detected [ 2.815997] ata_piix 0000:00:1f.1: version 2.12 [ 2.815997] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18 [ 2.815997] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 2.815997] scsi4 : ata_piix [ 2.815997] scsi5 : ata_piix [ 2.840100] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18c0 irq 14 [ 2.840157] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18c8 irq 15 [ 2.994584] ata5.00: ATAPI: MATSHITADVD-RAM UJ-841S, 1.50, max UDMA/33 [ 3.000504] ata5.00: configured for UDMA/33 [ 3.000582] ata6: port disabled. ignoring. [ 3.002000] scsi 4:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-841S 1.50 PQ: 0 ANSI: 5 [ 3.002001] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 3.002001] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 3.002001] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 3.002001] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 3.002001] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840 [ 3.003055] usb usb4: configuration #1 chosen from 1 choice [ 3.003132] hub 4-0:1.0: USB hub found [ 3.003184] hub 4-0:1.0: 2 ports detected [ 3.103998] ACPI: PCI Interrupt 0000:06:04.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 3.103998] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16 [ 3.103998] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 3.103998] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 3.103998] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 [ 3.103998] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860 [ 3.103998] usb usb5: configuration #1 chosen from 1 choice [ 3.105031] hub 5-0:1.0: USB hub found [ 3.105084] hub 5-0:1.0: 2 ports detected [ 3.160006] usb 1-1: new low speed USB device using uhci_hcd and address 2 [ 3.161007] firewire_ohci: Added fw-ohci device 0000:06:04.2, OHCI version 1.10 [ 3.161120] ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 3.161820] eth0: RealTek RTL8139 at 0xf88da000, 00:0f:b0:a5:9a:81, IRQ 21 [ 3.161874] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 3.211688] Driver 'sd' needs updating - please use bus_type methods [ 3.211834] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 3.211901] sd 0:0:0:0: [sda] Write Protect is off [ 3.211952] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 3.211973] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.212086] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 3.212154] sd 0:0:0:0: [sda] Write Protect is off [ 3.212206] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 3.212228] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.212295] sda:<4>Driver 'sr' needs updating - please use bus_type methods [ 3.300999] usb 1-1: configuration #1 chosen from 1 choice [ 3.343274] usbcore: registered new interface driver hiddev [ 3.358385] input: Logitech USB Receiver as /class/input/input1 [ 3.363033] input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1 [ 3.393030] input: Logitech USB Receiver as /class/input/input2 [ 3.398051] input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1 [ 3.398339] usbcore: registered new interface driver usbhid [ 3.398392] usbhid: v2.6:USB HID core driver [ 3.591462] sda1 sda2 < sda5 sda6 > sda3 [ 3.608998] sd 0:0:0:0: [sda] Attached SCSI disk [ 3.629031] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 3.629031] Uniform CD-ROM driver Revision: 3.20 [ 3.629031] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 3.632962] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 3.633040] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 3.661086] firewire_core: created device fw0: GUID 00023f5b8140757f, S400 [ 4.122469] PM: Starting manual resume from disk [ 4.130170] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 4.132481] Filesystem "dm-0": Disabling barriers, not supported by the underlying device [ 4.132729] XFS mounting filesystem dm-0 [ 4.214681] Ending clean XFS mount for filesystem: dm-0 [ 8.611728] Linux agpgart interface v0.103 [ 8.626735] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) [ 8.626874] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060) [ 8.626957] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 8.709000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3]) [ 8.709262] ACPI: ACPI0007:00 is registered as cooling_device0 [ 8.709317] ACPI: Processor [CPU0] (supports 8 throttling states) [ 8.725918] input: Power Button (FF) as /class/input/input3 [ 8.752060] ACPI: Power Button (FF) [PWRF] [ 8.752177] input: Lid Switch as /class/input/input4 [ 8.764121] ACPI: Lid Switch [LID0] [ 8.764225] input: Power Button (CM) as /class/input/input5 [ 8.788047] ACPI: Power Button (CM) [PWRB] [ 9.173654] ieee80211_crypt: registered algorithm 'NULL' [ 9.270000] Marking TSC unstable due to: TSC halts in idle. [ 9.414207] ACPI: AC Adapter [ACAD] (on-line) [ 9.667778] ACPI: Battery Slot [BAT1] (battery present) [ 9.689219] sdhci: Secure Digital Host Controller Interface driver [ 9.689279] sdhci: Copyright(c) Pierre Ossman [ 9.689359] sdhci: SDHCI controller found at 0000:06:04.4 [104c:8034] (rev 0) [ 9.689432] ACPI: PCI Interrupt 0000:06:04.4[D] -> GSI 19 (level, low) -> IRQ 19 [ 9.689551] mmc0: Will use DMA mode even though HW doesn't fully claim to support it. [ 9.689712] mmc0: SDHCI at 0xc4009400 irq 19 DMA [ 9.689772] mmc1: Will use DMA mode even though HW doesn't fully claim to support it. [ 9.689862] mmc1: SDHCI at 0xc4009000 irq 19 DMA [ 9.689921] mmc2: Will use DMA mode even though HW doesn't fully claim to support it. [ 9.690021] mmc2: SDHCI at 0xc4006400 irq 19 DMA [ 9.744484] input: PC Speaker as /class/input/input6 [ 9.751333] Real Time Clock Driver v1.12ac [ 9.769279] ACPI: PCI Interrupt 0000:06:04.3[B] -> GSI 17 (level, low) -> IRQ 17 [ 9.782047] input: Video Bus as /class/input/input7 [ 9.800258] Yenta: CardBus bridge found at 0000:06:04.0 [1179:ff00] [ 9.800339] PCI: Bus 7, cardbus bridge: 0000:06:04.0 [ 9.800390] IO window: 0x00006400-0x000064ff [ 9.800443] IO window: 0x00006800-0x000068ff [ 9.800496] PREFETCH window: 0x54000000-0x543fffff [ 9.800550] MEM window: 0x50000000-0x53ffffff [ 9.800605] Yenta: Enabling burst memory read transactions [ 9.800660] Yenta: Using CSCINT to route CSC interrupts to PCI [ 9.800712] Yenta: Routing CardBus interrupts to PCI [ 9.800766] Yenta TI: socket 0000:06:04.0, mfunc 0x10aa1b22, devctl 0x66 [ 9.805070] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) [ 9.805445] input: Video Bus as /class/input/input8 [ 9.816499] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 9.816558] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@xxxxxxxxxxxxxxx> [ 9.829066] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no) [ 9.840479] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq [ 9.840547] ipw2200: Copyright(c) 2003-2006 Intel Corporation [ 10.023833] Yenta: ISA IRQ mask 0x0cf8, PCI irq 16 [ 10.023892] Socket status: 30000006 [ 10.023942] Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a [ 10.024005] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff [ 10.024072] pcmcia: parent PCI bridge Memory window: 0xc4000000 - 0xc40fffff [ 10.031338] input: PS/2 Mouse as /class/input/input9 [ 10.034886] ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 10.044815] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection [ 10.044913] firmware: requesting ipw2200-bss.fw [ 10.067714] input: AlpsPS/2 ALPS GlidePoint as /class/input/input10 [ 10.534594] ipw2200: Radio Frequency Kill Switch is On: [ 10.534597] Kill switch must be turned off for wireless networking to work. [ 10.535092] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels) [ 10.535210] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 17 [ 10.535334] PCI: Setting latency timer of device 0000:00:1e.2 to 64 [ 11.182157] Clocksource tsc unstable (delta = -77135590 ns) [ 11.350030] intel8x0_measure_ac97_clock: measured 50736 usecs [ 11.350082] intel8x0: clocking to 48000 [ 12.172322] Non-volatile memory driver v1.2 [ 12.185343] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found [ 12.190783] firmware: requesting intel-ucode/06-0d-08 [ 12.217045] IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx> [ 12.229021] Machine check exception polling timer started. [ 12.286418] Adding 1461844k swap on /dev/sda5. Priority:-1 extents:1 across:1461844k [ 12.523578] Filesystem "dm-0": Disabling barriers, not supported by the underlying device [ 12.939611] kjournald starting. Commit interval 5 seconds [ 12.945052] EXT3 FS on sda1, internal journal [ 12.945052] EXT3-fs: mounted filesystem with ordered data mode. [ 12.977320] Filesystem "dm-3": Disabling barriers, not supported by the underlying device [ 12.997772] XFS mounting filesystem dm-3 [ 13.098262] Ending clean XFS mount for filesystem: dm-3 [ 13.143503] Filesystem "dm-1": Disabling barriers, not supported by the underlying device [ 13.163812] XFS mounting filesystem dm-1 [ 13.237413] Ending clean XFS mount for filesystem: dm-1 [ 13.238065] Filesystem "dm-2": Disabling barriers, not supported by the underlying device [ 13.238211] XFS mounting filesystem dm-2 [ 13.452498] Ending clean XFS mount for filesystem: dm-2 [ 17.686089] ip_tables: (C) 2000-2006 Netfilter Core Team [ 23.810166] usb 2-5: new high speed USB device using ehci_hcd and address 3 [ 23.925029] usb 2-5: configuration #1 chosen from 1 choice [ 23.963473] Initializing USB Mass Storage driver... [ 23.964288] scsi6 : SCSI emulation for USB Mass Storage devices [ 23.964454] usbcore: registered new interface driver usb-storage [ 23.964457] USB Mass Storage support registered. [ 23.965619] usb-storage: device found at 3 [ 23.965621] usb-storage: waiting for device to settle before scanning [ 24.565378] NET: Registered protocol family 17 [ 26.130297] atkbd.c: Unknown key pressed (translated set 2, code 0x95 on isa0060/serio0). [ 26.130297] atkbd.c: Use 'setkeycodes e015 <keycode>' to make it known. [ 26.130462] atkbd.c: Unknown key released (translated set 2, code 0x95 on isa0060/serio0). [ 26.130462] atkbd.c: Use 'setkeycodes e015 <keycode>' to make it known. [ 26.247963] ACPI: EC: non-query interrupt received, switching to interrupt mode [ 28.965258] usb-storage: device scan complete [ 28.965597] scsi 6:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2 [ 28.978447] sd 6:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB) [ 28.982239] sd 6:0:0:0: [sdb] Write Protect is off [ 28.982243] sd 6:0:0:0: [sdb] Mode Sense: 0b 00 00 08 [ 28.982245] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 28.984431] sd 6:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB) [ 28.985075] sd 6:0:0:0: [sdb] Write Protect is off [ 28.985075] sd 6:0:0:0: [sdb] Mode Sense: 0b 00 00 08 [ 28.985075] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 28.985075] sdb: sdb1 [ 28.985840] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 28.985840] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 105.379430] tun: Universal TUN/TAP device driver, 1.6 [ 105.379435] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx> [ 332.992622] warning: `ntpd' uses 32-bit capabilities (legacy support in use) [ 499.178040] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 499.178105] ata1.00: cmd ca/00:3e:76:45:81/00:00:00:00:00/e1 tag 0 dma 31744 out [ 499.178106] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 499.178168] ata1.00: status: { DRDY } [ 499.178220] ata1: hard resetting link [ 499.942034] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 499.943540] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 499.946056] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 499.947174] ata1.00: configured for UDMA/100 [ 499.947174] ata1: EH complete [ 499.947443] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 499.947443] sd 0:0:0:0: [sda] Write Protect is off [ 499.947443] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 499.947443] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 529.963038] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 529.963102] ata1.00: cmd ca/00:18:17:0b:94/00:00:00:00:00/e0 tag 0 dma 12288 out [ 529.963103] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 529.963166] ata1.00: status: { DRDY } [ 529.963217] ata1: hard resetting link [ 530.778173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 530.779373] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 530.781865] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 530.782983] ata1.00: configured for UDMA/100 [ 530.782983] ata1: EH complete [ 530.784112] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 530.784232] sd 0:0:0:0: [sda] Write Protect is off [ 530.784235] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 530.784474] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 560.791039] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 560.791104] ata1.00: cmd ca/00:28:1f:7f:99/00:00:00:00:00/e0 tag 0 dma 20480 out [ 560.791106] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 560.791168] ata1.00: status: { DRDY } [ 560.791219] ata1: hard resetting link [ 561.606033] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 561.607234] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 561.609720] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 561.610838] ata1.00: configured for UDMA/100 [ 561.610838] ata1: EH complete [ 561.611190] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 561.611354] sd 0:0:0:0: [sda] Write Protect is off [ 561.611354] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 561.612087] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 682.780718] ieee80211_crypt: registered algorithm 'CCMP' [ 683.768096] ieee80211_crypt: registered algorithm 'TKIP' [ 814.838039] ata1: limiting SATA link speed to 1.5 Gbps [ 814.838046] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 814.838109] ata1.00: cmd ca/00:10:57:b6:17/00:00:00:00:00/e2 tag 0 dma 8192 out [ 814.838110] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 814.838172] ata1.00: status: { DRDY } [ 814.838224] ata1: hard resetting link [ 815.602032] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 815.603229] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 815.606466] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 815.607598] ata1.00: configured for UDMA/100 [ 815.607598] ata1: EH complete [ 815.607806] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 815.607887] sd 0:0:0:0: [sda] Write Protect is off [ 815.607887] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 815.608242] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 845.624027] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 845.624087] ata1.00: cmd ca/00:10:df:17:79/00:00:00:00:00/e0 tag 0 dma 8192 out [ 845.624089] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 845.624150] ata1.00: status: { DRDY } [ 845.624199] ata1: hard resetting link [ 846.439166] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 846.440368] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 846.442863] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 846.443980] ata1.00: configured for UDMA/100 [ 846.443980] ata1: EH complete [ 846.444412] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 846.444783] sd 0:0:0:0: [sda] Write Protect is off [ 846.444783] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 846.444977] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 876.459037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 876.459103] ata1.00: cmd ca/00:01:87:08:71/00:00:00:00:00/e3 tag 0 dma 512 out [ 876.459105] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 876.459166] ata1.00: status: { DRDY } [ 876.459218] ata1: hard resetting link [ 877.325032] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 877.326233] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 877.329234] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 877.330350] ata1.00: configured for UDMA/100 [ 877.330350] ata1: EH complete [ 877.334027] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 877.334086] sd 0:0:0:0: [sda] Write Protect is off [ 877.334089] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 877.334125] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 970.438986] usb 2-5: USB disconnect, address 3 [ 1154.161035] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1154.161100] ata1.00: cmd ca/00:30:2f:19:f6/00:00:00:00:00/e2 tag 0 dma 24576 out [ 1154.161102] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1154.161164] ata1.00: status: { DRDY } [ 1154.161215] ata1: hard resetting link [ 1154.772159] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1154.773358] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1154.775851] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1154.776967] ata1.00: configured for UDMA/100 [ 1154.776967] ata1: EH complete [ 1154.777379] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1154.777571] sd 0:0:0:0: [sda] Write Protect is off [ 1154.777571] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1154.777766] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1186.493044] ata1.00: limiting speed to UDMA/66:PIO4 [ 1186.493050] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1186.493113] ata1.00: cmd ca/00:10:17:25:f6/00:00:00:00:00/e2 tag 0 dma 8192 out [ 1186.493115] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1186.493177] ata1.00: status: { DRDY } [ 1186.493228] ata1: hard resetting link [ 1187.155167] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1187.156365] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1187.158855] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1187.159972] ata1.00: configured for UDMA/66 [ 1187.159972] ata1: EH complete [ 1187.161154] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1187.161283] sd 0:0:0:0: [sda] Write Protect is off [ 1187.161286] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1187.161567] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1217.172036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1217.172098] ata1.00: cmd 35/00:00:47:01:f8/00:04:02:00:00/e0 tag 0 dma 524288 out [ 1217.172100] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1217.172162] ata1.00: status: { DRDY } [ 1217.172212] ata1: hard resetting link [ 1217.936036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1217.937237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1217.940440] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1217.941572] ata1.00: configured for UDMA/66 [ 1217.941572] ata1: EH complete [ 1217.949939] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1217.954021] sd 0:0:0:0: [sda] Write Protect is off [ 1217.954021] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1217.961634] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1315.895050] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1315.895088] ata1.00: cmd ca/00:20:d7:23:f8/00:00:00:00:00/e2 tag 0 dma 16384 out [ 1315.895090] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1315.895119] ata1.00: status: { DRDY } [ 1315.895138] ata1: hard resetting link [ 1316.557036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1316.558237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1316.561473] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1316.562606] ata1.00: configured for UDMA/66 [ 1316.562606] ata1: EH complete [ 1316.562820] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1316.562820] sd 0:0:0:0: [sda] Write Protect is off [ 1316.562820] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1316.562820] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1346.570036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1346.570064] ata1.00: cmd ca/00:08:57:0a:49/00:00:00:00:00/e0 tag 0 dma 4096 out [ 1346.570065] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1346.570095] ata1.00: status: { DRDY } [ 1346.570112] ata1: hard resetting link [ 1347.334036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1347.335237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1347.338409] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1347.339542] ata1.00: configured for UDMA/66 [ 1347.339542] ata1: EH complete [ 1347.339715] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1347.339793] sd 0:0:0:0: [sda] Write Protect is off [ 1347.339793] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1347.339976] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1377.351032] ata1.00: limiting speed to UDMA/33:PIO4 [ 1377.351036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1377.351063] ata1.00: cmd ca/00:08:cf:09:cd/00:00:00:00:00/e0 tag 0 dma 4096 out [ 1377.351064] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1377.351093] ata1.00: status: { DRDY } [ 1377.351111] ata1: hard resetting link [ 1378.166173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1378.167377] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1378.170232] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1378.171349] ata1.00: configured for UDMA/33 [ 1378.171349] ata1: EH complete [ 1378.171518] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1378.171593] sd 0:0:0:0: [sda] Write Protect is off [ 1378.171593] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1378.171656] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1408.178032] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1408.178060] ata1.00: cmd ca/00:10:c7:94:f1/00:00:00:00:00/e2 tag 0 dma 8192 out [ 1408.178061] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1408.178090] ata1.00: status: { DRDY } [ 1408.178108] ata1: hard resetting link [ 1408.993173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1408.994375] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1408.996870] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1408.997988] ata1.00: configured for UDMA/33 [ 1408.997988] ata1: EH complete [ 1408.998203] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1408.998340] sd 0:0:0:0: [sda] Write Protect is off [ 1408.998340] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1408.998523] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1439.006036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1439.006066] ata1.00: cmd ca/00:10:27:13:91/00:00:00:00:00/e2 tag 0 dma 8192 out [ 1439.006067] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1439.006097] ata1.00: status: { DRDY } [ 1439.006116] ata1: hard resetting link [ 1439.821174] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1439.822375] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1439.824872] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1439.825988] ata1.00: configured for UDMA/33 [ 1439.825988] ata1: EH complete [ 1439.826156] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1439.826252] sd 0:0:0:0: [sda] Write Protect is off [ 1439.826252] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1439.826488] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1469.836037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1469.836065] ata1.00: cmd ca/00:08:7f:4e:f8/00:00:00:00:00/e2 tag 0 dma 4096 out [ 1469.836067] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1469.836096] ata1.00: status: { DRDY } [ 1469.836114] ata1: hard resetting link [ 1470.651175] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1470.652376] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1470.654877] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1470.655994] ata1.00: configured for UDMA/33 [ 1470.655994] ata1: EH complete [ 1470.656164] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1470.656240] sd 0:0:0:0: [sda] Write Protect is off [ 1470.656240] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1470.656398] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1500.664044] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1500.664071] ata1.00: cmd ca/00:10:2f:72:f8/00:00:00:00:00/e2 tag 0 dma 8192 out [ 1500.664072] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1500.664101] ata1.00: status: { DRDY } [ 1500.664119] ata1: hard resetting link [ 1501.428036] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1501.429237] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1501.432423] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1501.433555] ata1.00: configured for UDMA/33 [ 1501.433555] ata1: EH complete [ 1501.433855] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1501.433951] sd 0:0:0:0: [sda] Write Protect is off [ 1501.433951] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1501.434106] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1531.443037] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1531.443064] ata1.00: cmd ca/00:08:e7:91:f8/00:00:00:00:00/e2 tag 0 dma 4096 out [ 1531.443066] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1531.443095] ata1.00: status: { DRDY } [ 1531.443112] ata1: hard resetting link [ 1532.207034] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1532.208235] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1532.211421] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1532.212554] ata1.00: configured for UDMA/33 [ 1532.212554] ata1: EH complete [ 1532.212758] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1532.212867] sd 0:0:0:0: [sda] Write Protect is off [ 1532.212867] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1532.213025] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1562.219036] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1562.219064] ata1.00: cmd ca/00:08:2f:ac:f8/00:00:00:00:00/e2 tag 0 dma 4096 out [ 1562.219066] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1562.219095] ata1.00: status: { DRDY } [ 1562.219113] ata1: hard resetting link [ 1562.983062] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1562.984249] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1562.987424] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1562.988556] ata1.00: configured for UDMA/33 [ 1562.988556] ata1: EH complete [ 1562.988748] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1562.988851] sd 0:0:0:0: [sda] Write Protect is off [ 1562.988851] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1562.989049] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1592.996034] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1592.996062] ata1.00: cmd ca/00:10:5f:c9:f8/00:00:00:00:00/e2 tag 0 dma 8192 out [ 1592.996063] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1592.996093] ata1.00: status: { DRDY } [ 1592.996110] ata1: hard resetting link [ 1593.760172] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1593.761372] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1593.763862] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded [ 1593.764977] ata1.00: configured for UDMA/33 [ 1593.764977] ata1: EH complete [ 1593.765183] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) [ 1593.765206] sd 0:0:0:0: [sda] Write Protect is off [ 1593.765206] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1593.765206] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1617.738192] usb 2-5: new high speed USB device using ehci_hcd and address 4 [ 1617.852903] usb 2-5: configuration #1 chosen from 1 choice [ 1617.859032] scsi7 : SCSI emulation for USB Mass Storage devices [ 1617.862832] usb-storage: device found at 4 [ 1617.862834] usb-storage: waiting for device to settle before scanning [ 1622.862353] usb-storage: device scan complete [ 1622.862703] scsi 7:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2 [ 1622.864004] sd 7:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB) [ 1622.864615] sd 7:0:0:0: [sdb] Write Protect is off [ 1622.864618] sd 7:0:0:0: [sdb] Mode Sense: 0b 00 00 08 [ 1622.864621] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 1622.866735] sd 7:0:0:0: [sdb] 257792 512-byte hardware sectors (132 MB) [ 1622.867362] sd 7:0:0:0: [sdb] Write Protect is off [ 1622.867365] sd 7:0:0:0: [sdb] Mode Sense: 0b 00 00 08 [ 1622.867367] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 1622.867420] sdb: sdb1 [ 1622.868538] sd 7:0:0:0: [sdb] Attached SCSI removable disk [ 1622.868580] sd 7:0:0:0: Attached scsi generic sg2 type 0