Eric Moore wrote:
> The SG tools will work with mpt fusion if your passing the ATA_12
> (opcode=0xA1) and ATA_16 (opcode=0x85). This is implemented in
> fusion firmware. If your failing, then your probably having old
> firmware. I suggest that you upgrading by going to the download
> site located here: http://www.lsi.com/cm/DownloadSearch.do?locale=EN.
> Ken Stewart is from support, he should be able to assist you with
> upgrading the firmware if you encounter any problems.
Hi Eric,
I have already logged a bug with Fedora, but can you think of anything
that would have changed between 2.6.25.4 and 2.6.25.6 that would have
broken this?
I have just updated from 2.6.25.4-30.fc9.x86_64 to
2.6.25.6-55.fc9.x86_64 and smartmontools now causes LSISAS1068E
controller resets, where it was working perfectly before:
mptscsih: ioc0: attempting task abort! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: ATA command pass through(16): 85 08 0e 00 00 00
01 00 00
00 00 00 00 00 ec 00
mptbase: ioc0: LogInfo(0x31140000): Originator={PL}, Code={IO Executed},
SubCode(0x0000)
mptscsih: ioc0: task abort: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting task abort! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: Test Unit Ready: 00 00 00 00 00 00
mptbase: ioc0: LogInfo(0x31130000): Originator={PL}, Code={IO Not Yet
Executed},
SubCode(0x0000)
mptscsih: ioc0: task abort: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting target reset! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: ATA command pass through(16): 85 08 0e 00 00 00
01 00 00
00 00 00 00 00 ec 00
mptscsih: ioc0: target reset: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting task abort! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: Test Unit Ready: 00 00 00 00 00 00
mptbase: ioc0: LogInfo(0x31130000): Originator={PL}, Code={IO Not Yet
Executed},
SubCode(0x0000)
mptscsih: ioc0: task abort: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting bus reset! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: ATA command pass through(16): 85 08 0e 00 00 00
01 00 00
00 00 00 00 00 ec 00
mptscsih: ioc0: bus reset: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting task abort! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: Test Unit Ready: 00 00 00 00 00 00
mptbase: ioc0: LogInfo(0x31130000): Originator={PL}, Code={IO Not Yet
Executed},
SubCode(0x0000)
mptscsih: ioc0: task abort: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting host reset! (sc=ffff81023d0c6b40)
mptbase: ioc0: Initiating recovery
mptscsih: ioc0: host reset: SUCCESS (sc=ffff81023d0c6b40)
sd 4:0:0:0: Device offlined - not ready after error recovery
program smartd is using a deprecated SCSI ioctl, please convert it to SG_IO
smartd.conf entries are in the form:
/dev/sdc -d sat,16 -a -I 194 -s L/../../1/01
and all drives behind the controller do the same.
Regards,
Richard
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html