I have a platform with a single CompactFlash socket connected to a
Broadcom HT1000's PATA port. With libata's pata_serverworks, it ends
up using drive-side 80-conductor cable detection (Broadcom provides no
cable bits for the BIOS to report what is attached). The
CompactFlashes I am using mis-report the cable type, and
pata_serverworks limits to UDMA2. I tried to use the recent addition
of libata.force, but it does not seem to work like I would expect it
to. An excerpt from dmesg:
scsi4 : pata_serverworks
scsi5 : pata_serverworks
ata5: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata6: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata5: FORCE: cable set to 80c
ata5.00: ATA-4: CF CARD, 20080308, max UDMA/66
ata5.00: 15662304 sectors, multi 0: LBA
ata5.00: limited to UDMA/33 due to 40-wire cable
ata5.00: configured for UDMA/33
The force parameter is certainly getting accepted, but then 3 lines
later, it believes it has a 40 conductor cable.
I have attached the full dmesg. This is vanilla 2.6.25.3 with "options
libata force=80c" added in the initrd.
Yes, I know I should just get a more well-behaved device, but both of
the high-speed (UDMA) CFs I am using mis-report the cable detection. I
would bet many other high-speed CFs do the same. I have already
contacted the CF manufacturer to look into it. For now, though, I'd
like to run UDMA4, and the force parameter seems like it would do what
I want.
Is force=80c what I want? Should it work?
Thanks
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.25.3 (root@xxxxxxxxxxxxxxxxx) (gcc version 4.3.0 20080428 (Red Hat 4.3.0-8) (GCC) ) #1 SMP Wed May 14 12:56:51 EDT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
BIOS-e820: 000000000009d400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ffd0000 (usable)
BIOS-e820: 000000007ffd0000 - 000000007ffde000 (ACPI data)
BIOS-e820: 000000007ffde000 - 000000007ffe0000 (ACPI NVS)
BIOS-e820: 000000007ffe0000 - 000000007ffee000 (reserved)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec03000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at [c00ff780] 000ff780
Entering add_active_range(0, 0, 524240) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 524240
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 524240
On node 0 totalpages: 524240
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 2303 pages used for memmap
HighMem zone: 292561 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI present.
Using APIC driver default
ACPI: RSDP 000F8EB0, 0014 (r0 ACPIAM)
ACPI: RSDT 7FFD0000, 003C (r1 050908 RSDT1229 20080509 MSFT 97)
ACPI: FACP 7FFD0200, 0084 (r1 050908 FACP1229 20080509 MSFT 97)
ACPI: DSDT 7FFD04F0, 406A (r1 B0B0_ B0B0_009 9 INTL 20051117)
ACPI: FACS 7FFDE000, 0040
ACPI: APIC 7FFD0390, 00CA (r1 050908 APIC1229 20080509 MSFT 97)
ACPI: MCFG 7FFD0460, 003C (r1 050908 OEMMCFG 20080509 MSFT 97)
ACPI: OEMB 7FFDE040, 008E (r1 050908 OEMB1229 20080509 MSFT 97)
ACPI: HPET 7FFD4560, 0038 (r1 050908 OEMHPET 20080509 MSFT 97)
ACPI: SSDT 7FFD45A0, 043E (r1 A M I POWERNOW 1 AMD 1)
Detected use of extended apic ids on hypertransport bus
Detected use of extended apic ids on hypertransport bus
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x508
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Processor #2 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
Processor #4 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
Processor #5 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x86] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x87] disabled)
ACPI: LAPIC (acpi_id[0x09] lapic_id[0x88] disabled)
ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x89] disabled)
ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x8a] disabled)
ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x8b] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x06] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 6, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x07] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 7, version 17, address 0xfec01000, GSI 16-31
ACPI: IOAPIC (id[0x08] address[0xfec02000] gsi_base[32])
IOAPIC[2]: apic_id 8, version 17, address 0xfec02000, GSI 32-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 3 I/O APICs
ACPI: HPET id: 0x0 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000
PM: Registered nosave memory: 00000000000e6000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520145
Kernel command line: ro root=UUID=f00d22b0-1376-4e78-9e25-579d6e784d92 libata.force=5:80c
Unknown boot option `libata.force=5:80c': ignoring
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
mapped IOAPIC to ffff9000 (fec01000)
mapped IOAPIC to ffff8000 (fec02000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07b4000 soft=c0794000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2200.178 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2070536k/2096960k available (2226k kernel code, 25168k reserved, 1115k data, 280k init, 1179456k highmem)
virtual kernel memory layout:
fixmap : 0xffc53000 - 0xfffff000 (3760 kB)
pkmap : 0xff400000 - 0xff800000 (4096 kB)
vmalloc : 0xf8800000 - 0xff3fe000 ( 107 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc074b000 - 0xc0791000 ( 280 kB)
.data : 0xc062c8ca - 0xc07437f8 (1115 kB)
.text : 0xc0400000 - 0xc062c8ca (2226 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=6, Nodes=1
hpet clockevent registered
Calibrating delay using timer specific routine.. 4402.84 BogoMIPS (lpj=2201424)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(2) -> Core 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
CPU0: AMD Dual-Core AMD Opteron(tm) Processor 8214 HE stepping 03
Booting processor 1/1 ip 4000
CPU 1 irqstacks, hard=c07b5000 soft=c0795000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4338.37 BogoMIPS (lpj=2169185)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1(2) -> Core 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Dual-Core AMD Opteron(tm) Processor 8214 HE stepping 03
Booting processor 2/2 ip 4000
CPU 2 irqstacks, hard=c07b6000 soft=c0796000
Initializing CPU#2
Calibrating delay using timer specific routine.. 4400.16 BogoMIPS (lpj=2200084)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2(2) -> Core 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: AMD Dual-Core AMD Opteron(tm) Processor 8214 HE stepping 03
Booting processor 3/3 ip 4000
CPU 3 irqstacks, hard=c07b7000 soft=c0797000
Initializing CPU#3
Calibrating delay using timer specific routine.. 4400.16 BogoMIPS (lpj=2200082)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3(2) -> Core 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: AMD Dual-Core AMD Opteron(tm) Processor 8214 HE stepping 03
Booting processor 4/4 ip 4000
CPU 4 irqstacks, hard=c07b8000 soft=c0798000
Initializing CPU#4
Calibrating delay using timer specific routine.. 4400.13 BogoMIPS (lpj=2200068)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 4(2) -> Core 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#4.
CPU4: AMD Dual-Core AMD Opteron(tm) Processor 8214 HE stepping 03
Booting processor 5/5 ip 4000
CPU 5 irqstacks, hard=c07b9000 soft=c0799000
Initializing CPU#5
Calibrating delay using timer specific routine.. 4400.16 BogoMIPS (lpj=2200084)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 5(2) -> Core 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#5.
CPU5: AMD Dual-Core AMD Opteron(tm) Processor 8214 HE stepping 03
Total of 6 processors activated (26341.85 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 6 CPUs
CPU0 attaching sched-domain:
domain 0: span 0000003f
groups: 00000001 00000002 00000004 00000008 00000010 00000020
CPU1 attaching sched-domain:
domain 0: span 0000003f
groups: 00000002 00000004 00000008 00000010 00000020 00000001
CPU2 attaching sched-domain:
domain 0: span 0000003f
groups: 00000004 00000008 00000010 00000020 00000001 00000002
CPU3 attaching sched-domain:
domain 0: span 0000003f
groups: 00000008 00000010 00000020 00000001 00000002 00000004
CPU4 attaching sched-domain:
domain 0: span 0000003f
groups: 00000010 00000020 00000001 00000002 00000004 00000008
CPU5 attaching sched-domain:
domain 0: span 0000003f
groups: 00000020 00000001 00000002 00000004 00000008 00000010
net_namespace: 548 bytes
Booting paravirtualized kernel on bare hardware
Time: 18:02:05 Date: 05/14/08
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=12
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: Error attaching device data
ACPI: Error attaching device data
ACPI: Error attaching device data
ACPI: Error attaching device data
ACPI: Error attaching device data
ACPI: Error attaching device data
ACPI: Error attaching device data
ACPI: Error attaching device data
ACPI: Error attaching device data
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: Enabling HT MSI Mapping
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR14._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR1E._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR28._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR32._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR3C._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1.P1P2._PRT]
ACPI: PCI Interrupt Link [LN00] (IRQs 3 4 7 9 *11 12 14 15)
ACPI: PCI Interrupt Link [LN01] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN02] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN03] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN04] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN05] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN06] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN07] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN08] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN09] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN10] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN11] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN12] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN13] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN14] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN15] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN16] (IRQs 1 3 4 6 7 *9 11 12 14 15)
ACPI: PCI Interrupt Link [LN17] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN18] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN19] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN20] (IRQs 1 *3 4 6 7 9 11 12 14 15)
ACPI: PCI Interrupt Link [LN21] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN22] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN23] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN24] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN25] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN26] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN27] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN28] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN29] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LN30] (IRQs 1 3 4 6 7 9 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNUS] (IRQs *10)
ACPI: PCI Interrupt Link [LNSA] (IRQs *5)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 73, should be 72 [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI Error (evxfevnt-0186): Could not enable RealTimeClock event [20070126]
ACPI Warning (evxface-0145): Could not enable fixed event 4 [20070126]
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 4
Switched to high resolution mode on CPU 5
system 00:05: ioport range 0x4d0-0x4d1 has been reserved
system 00:05: ioport range 0xc00-0xc01 has been reserved
system 00:05: ioport range 0xcd6-0xcd7 has been reserved
system 00:05: ioport range 0xcd4-0xcd5 has been reserved
system 00:05: ioport range 0xcd8-0xcdf has been reserved
system 00:05: ioport range 0x40b-0x40b has been reserved
system 00:05: ioport range 0x4d6-0x4d6 has been reserved
system 00:05: ioport range 0xc06-0xc07 has been reserved
system 00:05: ioport range 0xc14-0xc14 has been reserved
system 00:05: ioport range 0xc49-0xc49 has been reserved
system 00:05: ioport range 0xc4a-0xc4a has been reserved
system 00:05: ioport range 0xc50-0xc51 has been reserved
system 00:05: ioport range 0xc52-0xc52 has been reserved
system 00:05: ioport range 0xc6c-0xc6c has been reserved
system 00:05: ioport range 0xc6f-0xc6f has been reserved
system 00:05: ioport range 0x500-0x57f has been reserved
system 00:09: ioport range 0xa40-0xa5f has been reserved
system 00:09: ioport range 0xa20-0xa3f has been reserved
system 00:09: ioport range 0xa00-0xa0f has been reserved
system 00:09: ioport range 0xa04-0xa13 could not be reserved
system 00:09: ioport range 0xa10-0xa1f has been reserved
system 00:09: ioport range 0xa60-0xa7f has been reserved
system 00:09: ioport range 0xa80-0xa8f has been reserved
system 00:09: ioport range 0xaa0-0xabf has been reserved
system 00:09: ioport range 0xac0-0xadf has been reserved
system 00:09: ioport range 0xae0-0xaff has been reserved
system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0b: iomem range 0x0-0x9ffff could not be reserved
system 00:0b: iomem range 0xc0000-0xcffff could not be reserved
system 00:0b: iomem range 0xe0000-0xfffff could not be reserved
system 00:0b: iomem range 0x100000-0xd7ffffff could not be reserved
system 00:0b: iomem range 0xff780000-0xffffffff could not be reserved
PCI: Bridge: 0000:01:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:01.0
IO window: c000-dfff
MEM window: 0xdfd00000-0xdfdfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:04:01.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:04:02.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:04:03.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:04:04.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:03:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
IO window: disabled.
MEM window: 0xdfe00000-0xdfefffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:08.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:09.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0a.0
IO window: e000-efff
MEM window: 0xdff00000-0xdfffffff
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:00:06.0 to 64
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:03:00.0 to 64
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:04:01.0 to 64
ACPI: PCI Interrupt 0000:04:02.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:04:02.0 to 64
ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:04:03.0 to 64
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:04:04.0 to 64
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:00:07.0 to 64
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:00:08.0 to 64
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:00:09.0 to 64
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 32 (level, low) -> IRQ 32
PCI: Setting latency timer of device 0000:00:0a.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3218k freed
apm: BIOS not found.
audit: initializing netlink socket (disabled)
type=2000 audit(1210788124.820:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:04.0: Boot video device
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
PCI: Setting latency timer of device 0000:00:07.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
PCI: Setting latency timer of device 0000:00:08.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:08.0:pcie00]
PCI: Setting latency timer of device 0000:00:09.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:09.0:pcie00]
PCI: Setting latency timer of device 0000:00:0a.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0a.0:pcie00]
PCI: Setting latency timer of device 0000:03:00.0 to 64
assign_interrupt_mode Found MSI capability
PCI: Setting latency timer of device 0000:04:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:04:01.0:pcie22]
PCI: Setting latency timer of device 0000:04:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:04:02.0:pcie22]
PCI: Setting latency timer of device 0000:04:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:04:03.0:pcie22]
PCI: Setting latency timer of device 0000:04:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:04:04.0:pcie22]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: ACPI0007:01 is registered as cooling_device1
ACPI: ACPI0007:02 is registered as cooling_device2
ACPI: ACPI0007:03 is registered as cooling_device3
ACPI: ACPI0007:04 is registered as cooling_device4
ACPI: ACPI0007:05 is registered as cooling_device5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Magic number: 8:914:38
hash matches device 00:0a
Freeing unused kernel memory: 280k freed
Write protecting the kernel read-only data: 904k
ACPI: PCI Interrupt 0000:00:03.2[A] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.2: irq 10, io mem 0xdfcfd000
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25.3 ehci_hcd
usb usb1: SerialNumber: 0000:00:03.2
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 10, io mem 0xdfcff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.25.3 ohci_hcd
usb usb2: SerialNumber: 0000:00:03.0
ACPI: PCI Interrupt 0000:00:03.1[A] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.1: irq 10, io mem 0xdfcfe000
hub 1-0:1.0: unable to enumerate USB device on port 3
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.25.3 ohci_hcd
usb usb3: SerialNumber: 0000:00:03.1
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
libata version 3.00 loaded.
sata_svw 0000:01:0e.0: version 2.3
ACPI: PCI Interrupt 0000:01:0e.0[A] -> GSI 5 (level, low) -> IRQ 5
scsi0 : sata_svw
scsi1 : sata_svw
scsi2 : sata_svw
scsi3 : sata_svw
ata1: SATA max UDMA/133 mmio m8192@0xdfdfe000 port 0xdfdfe000 irq 5
ata2: SATA max UDMA/133 mmio m8192@0xdfdfe000 port 0xdfdfe100 irq 5
ata3: SATA max UDMA/133 mmio m8192@0xdfdfe000 port 0xdfdfe200 irq 5
ata4: SATA max UDMA/133 mmio m8192@0xdfdfe000 port 0xdfdfe300 irq 5
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: FORCE: cable set to 80c
ata1.00: ATAPI: PLEXTOR DVDR PX-755A, 1.04, max UDMA/66
ata1.00: configured for UDMA/66
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2: FORCE: cable set to 80c
ata2.00: ATA-7: WDC WD1600YD-01NVB1, 10.02E01, max UDMA/133
ata2.00: 321672960 sectors, multi 16: LBA48 NCQ (depth 0/1)
ata2.00: configured for UDMA/133
ata3: SATA link down (SStatus 4 SControl 300)
ata3: FORCE: cable set to 80c
ata4: SATA link down (SStatus 4 SControl 300)
ata4: FORCE: cable set to 80c
scsi 0:0:0:0: CD-ROM PLEXTOR DVDR PX-755A 1.04 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access ATA WDC WD1600YD-01N 10.0 PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 1:0:0:0: [sda] Attached SCSI disk
ACPI: PCI Interrupt 0000:01:0e.1[A] -> GSI 5 (level, low) -> IRQ 5
hub 3-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 3-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
type=1404 audit(1210788133.711:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
SELinux:8192 avtab hash slots allocated. Num of rules:172315
SELinux:8192 avtab hash slots allocated. Num of rules:172315
security: 8 users, 12 roles, 2301 types, 116 bools, 1 sens, 1024 cats
security: 72 classes, 172315 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: policy loaded with handle_unknown=allow
type=1403 audit(1210788134.289:3): policy loaded auid=4294967295 ses=4294967295
hub 3-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
piix4_smbus 0000:00:02.0: Found 0000:00:02.0 device
input: PC Speaker as /devices/platform/pcspkr/input/input2
sr 0:0:0:0: Attached scsi generic sg0 type 5
sd 1:0:0:0: Attached scsi generic sg1 type 0
e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
e1000e: Copyright (c) 1999-2007 Intel Corporation.
ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 36 (level, low) -> IRQ 36
PCI: Setting latency timer of device 0000:0c:00.0 to 64
eth0: (PCI Express:2.5GB/s:Width x4) 00:09:1f:00:10:24
eth0: Intel(R) PRO/1000 Network Connection
eth0: MAC: 0, PHY: 4, PBA No: 123456-078
ACPI: PCI Interrupt 0000:0c:00.1[B] -> GSI 36 (level, low) -> IRQ 36
PCI: Setting latency timer of device 0000:0c:00.1 to 64
eth1: (PCI Express:2.5GB/s:Width x4) 00:09:1f:00:10:25
eth1: Intel(R) PRO/1000 Network Connection
eth1: MAC: 0, PHY: 4, PBA No: 123456-078
scsi4 : pata_serverworks
scsi5 : pata_serverworks
ata5: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata6: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata5: FORCE: cable set to 80c
ata5.00: ATA-4: CF CARD, 20080308, max UDMA/66
ata5.00: 15662304 sectors, multi 0: LBA
ata5.00: limited to UDMA/33 due to 40-wire cable
ata5.00: configured for UDMA/33
ata6: FORCE: cable set to 80c
scsi 4:0:0:0: Direct-Access ATA CF CARD 2008 PQ: 0 ANSI: 5
sd 4:0:0:0: [sdb] 15662304 512-byte hardware sectors (8019 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sdb] 15662304 512-byte hardware sectors (8019 MB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 4:0:0:0: [sdb] Attached SCSI disk
sd 4:0:0:0: Attached scsi generic sg2 type 0
device-mapper: multipath: version 1.0.5 loaded
hub 3-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
hub 3-0:1.0: unable to enumerate USB device on port 1
loop: module loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-1 extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
powernow-k8: Found 1 Dual-Core AMD Opteron(tm) Processor 8214 HE processors (6 cpu cores) (version 2.20.00)
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0xe
powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x10
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0xe
powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x10
powernow-k8: 0 : fid 0xe (2200 MHz), vid 0xe
powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x10
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
Clocksource tsc unstable (delta = -95467594 ns)
ip_tables: (C) 2000-2006 Netfilter Core Team
ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0: Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
fuse init (API version 7.9)
SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
SELinux: initialized (dev fuse, type fuse), uses genfs_contexts
SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts
hub 1-0:1.0: unable to enumerate USB device on port 3
usb 3-1: new low speed USB device using ohci_hcd and address 6
usb 3-1: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:03.1/usb3/3-1/3-1:1.0/input/input3
input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:03.1-1
usb 3-1: New USB device found, idVendor=046d, idProduct=c040
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-1: Product: USB-PS/2 Optical Mouse
usb 3-1: Manufacturer: Logitech
