* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base().
* Factor out code for forcing host out of "simplex" mode from
ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper.
* Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229),
amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and
serverworks (for CSB5) host drivers.
* Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag
instead of checking dev->device (BTW the code was buggy because it didn't
check for dev->vendor, luckily none of these PCI Device IDs was used by
some other vendor for PCI IDE controller).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
---
drivers/ide/pci/alim15x3.c | 7 ++-
drivers/ide/pci/amd74xx.c | 1
drivers/ide/pci/cmd64x.c | 4 +-
drivers/ide/pci/generic.c | 3 +
drivers/ide/pci/serverworks.c | 4 +-
drivers/ide/setup-pci.c | 77 ++++++++++++++++++------------------------
include/linux/ide.h | 2 +
7 files changed, 49 insertions(+), 49 deletions(-)
Index: b/drivers/ide/pci/alim15x3.c
===================================================================
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -775,7 +775,7 @@ static int __devinit alim15x3_init_one(s
};
struct ide_port_info d = ali15x3_chipset;
- u8 rev = dev->revision;
+ u8 rev = dev->revision, idx = id->driver_data;
if (pci_dev_present(ati_rs100))
printk(KERN_WARNING "alim15x3: ATI Radeon IGP Northbridge is not yet fully tested.\n");
@@ -798,6 +798,9 @@ static int __devinit alim15x3_init_one(s
d.udma_mask = ATA_UDMA6;
}
+ if (idx == 0)
+ d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
+
#if defined(CONFIG_SPARC64)
d.init_hwif = init_hwif_common_ali15x3;
#endif /* CONFIG_SPARC64 */
@@ -807,7 +810,7 @@ static int __devinit alim15x3_init_one(s
static const struct pci_device_id alim15x3_pci_tbl[] = {
{ PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5229), 0 },
- { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5228), 0 },
+ { PCI_VDEVICE(AL, PCI_DEVICE_ID_AL_M5228), 1 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, alim15x3_pci_tbl);
Index: b/drivers/ide/pci/amd74xx.c
===================================================================
--- a/drivers/ide/pci/amd74xx.c
+++ b/drivers/ide/pci/amd74xx.c
@@ -295,6 +295,7 @@ static int __devinit amd74xx_probe(struc
if (idx == 1) {
if (dev->revision <= 7)
d.swdma_mask = 0;
+ d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
} else if (idx == 4) {
if (dev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
dev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
Index: b/drivers/ide/pci/cmd64x.c
===================================================================
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -443,7 +443,9 @@ static const struct ide_port_info cmd64x
.init_chipset = init_chipset_cmd64x,
.init_hwif = init_hwif_cmd64x,
.enablebits = {{0x00,0x00,0x00}, {0x51,0x08,0x08}},
- .host_flags = IDE_HFLAG_ABUSE_PREFETCH | IDE_HFLAG_BOOTABLE,
+ .host_flags = IDE_HFLAG_CLEAR_SIMPLEX |
+ IDE_HFLAG_ABUSE_PREFETCH |
+ IDE_HFLAG_BOOTABLE,
.pio_mask = ATA_PIO5,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = 0x00, /* no udma */
Index: b/drivers/ide/pci/generic.c
===================================================================
--- a/drivers/ide/pci/generic.c
+++ b/drivers/ide/pci/generic.c
@@ -104,7 +104,8 @@ static const struct ide_port_info generi
{ /* 14 */
.name = "Revolution",
- .host_flags = IDE_HFLAG_TRUST_BIOS_FOR_DMA |
+ .host_flags = IDE_HFLAG_CLEAR_SIMPLEX |
+ IDE_HFLAG_TRUST_BIOS_FOR_DMA |
IDE_HFLAG_OFF_BOARD,
.swdma_mask = ATA_SWDMA2,
.mwdma_mask = ATA_MWDMA2,
Index: b/drivers/ide/pci/serverworks.c
===================================================================
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -418,7 +418,9 @@ static int __devinit svwks_init_one(stru
d = serverworks_chipsets[idx];
- if (idx == 2 || idx == 3) {
+ if (idx == 1)
+ d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
+ else if (idx == 2 || idx == 3) {
if ((PCI_FUNC(dev->devfn) & 1) == 0) {
if (pci_resource_start(dev, 0) != 0x01f1)
d.host_flags &= ~IDE_HFLAG_BOOTABLE;
Index: b/drivers/ide/setup-pci.c
===================================================================
--- a/drivers/ide/setup-pci.c
+++ b/drivers/ide/setup-pci.c
@@ -140,6 +140,16 @@ static int ide_setup_pci_baseregs (struc
}
#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
+static void ide_pci_clear_simplex(unsigned long dma_base, const char *name)
+{
+ u8 dma_stat = inb(dma_base + 2);
+
+ outb(dma_stat & 0x60, dma_base + 2);
+ dma_stat = inb(dma_base + 2);
+ if (dma_stat & 0x80)
+ printk(KERN_INFO "%s: simplex device: DMA forced\n", name);
+}
+
/**
* ide_get_or_set_dma_base - setup BMIBA
* @d: IDE port info
@@ -154,6 +164,7 @@ static unsigned long ide_get_or_set_dma_
{
unsigned long dma_base = 0;
struct pci_dev *dev = hwif->pci_dev;
+ u8 dma_stat = 0;
if (hwif->mmio)
return hwif->dma_base;
@@ -174,52 +185,30 @@ static unsigned long ide_get_or_set_dma_
if (hwif->channel)
dma_base += 8;
- if ((d->host_flags & IDE_HFLAG_CS5520) == 0) {
- u8 simplex_stat = 0;
+ if (d->host_flags & IDE_HFLAG_CS5520)
+ goto out;
- switch(dev->device) {
- case PCI_DEVICE_ID_AL_M5219:
- case PCI_DEVICE_ID_AL_M5229:
- case PCI_DEVICE_ID_AMD_VIPER_7409:
- case PCI_DEVICE_ID_CMD_643:
- case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
- case PCI_DEVICE_ID_REVOLUTION:
- simplex_stat = inb(dma_base + 2);
- outb(simplex_stat & 0x60, dma_base + 2);
- simplex_stat = inb(dma_base + 2);
- if (simplex_stat & 0x80) {
- printk(KERN_INFO "%s: simplex device: "
- "DMA forced\n",
- d->name);
- }
- break;
- default:
- /*
- * If the device claims "simplex" DMA,
- * this means only one of the two interfaces
- * can be trusted with DMA at any point in time.
- * So we should enable DMA only on one of the
- * two interfaces.
- */
- simplex_stat = hwif->INB(dma_base + 2);
- if (simplex_stat & 0x80) {
- /* simplex device? */
-/*
- * At this point we haven't probed the drives so we can't make the
- * appropriate decision. Really we should defer this problem
- * until we tune the drive then try to grab DMA ownership if we want
- * to be the DMA end. This has to be become dynamic to handle hot
- * plug.
- */
- if (hwif->mate && hwif->mate->dma_base) {
- printk(KERN_INFO "%s: simplex device: "
- "DMA disabled\n",
- d->name);
- dma_base = 0;
- }
- }
- }
+ if (d->host_flags & IDE_HFLAG_CLEAR_SIMPLEX) {
+ ide_pci_clear_simplex(dma_base, d->name);
+ goto out;
}
+
+ /*
+ * If the device claims "simplex" DMA, this means that only one of
+ * the two interfaces can be trusted with DMA at any point in time
+ * (so we should enable DMA only on one of the two interfaces).
+ *
+ * FIXME: At this point we haven't probed the drives so we can't make
+ * the appropriate decision. Really we should defer this problem until
+ * we tune the drive then try to grab DMA ownership if we want to be
+ * the DMA end. This has to be become dynamic to handle hot-plug.
+ */
+ dma_stat = hwif->INB(dma_base + 2);
+ if ((dma_stat & 0x80) && hwif->mate && hwif->mate->dma_base) {
+ printk(KERN_INFO "%s: simplex device: DMA disabled\n", d->name);
+ dma_base = 0;
+ }
+out:
return dma_base;
}
#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
Index: b/include/linux/ide.h
===================================================================
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -1096,6 +1096,8 @@ enum {
IDE_HFLAG_ABUSE_SET_DMA_MODE = (1 << 26),
/* host is CY82C693 */
IDE_HFLAG_CY82C693 = (1 << 27),
+ /* force host out of "simplex" mode */
+ IDE_HFLAG_CLEAR_SIMPLEX = (1 << 28),
};
#ifdef CONFIG_BLK_DEV_OFFBOARD
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
