Well, I feel foolish.
One problem is that the prebuilt kernel is using an initrd
image, so I made your patch changes, and put them into
/lib/modules/`uname -r`/kernel/drivers/ata/sata_sil.ko,
and guess what, they never got loaded. Foolishness on my
part.
Anyway, this time I got to the single boot prompt, where I did
a 'rmmod sata_sil', and a 'modprobe sata_sil', and I know
it loaded the new version, because you can see the
'sata_sil 0000:02:0b.0: version 2.2b', which I put in
to verify what the heck is going on.
This machine is pretty slow to compile the kernel, which is
why I was trying to short cut the build/install some, but
I might try to build the kernel on a faster machine and see if
I can get the initrd image rebuilt also.
Tejun Heo wrote:
Mark Paulus wrote:
I applied the patch, and not much difference. Still the same issue, and
here
is the new dmesg output.
Weird, okay, here's updated patch. Please try this one and report the
dmesg. FYI, it won't fix the problem. It's just to find out what's
going on.
--
Mark Paulus
2424 Garden of the Gods Rd | Phone: v622-5578 / 719-535-5578
0419/117 - LEC Access ; D5-1010 | FAX: 719-535-1665
Colo Springs, CO 80919 | 1800PageMCI / 1406052
AIM : mgpaulus1 / sametime : mark.paulus
Linux version 2.6.22-3-686 (Debian 2.6.22-5~bpo.1) (norbert@xxxxxxxxxxxxx) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Wed Oct 31 16:15:58 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
BIOS-e820: 000000001ffd0000 - 000000001fff0000 (ACPI NVS)
BIOS-e820: 000000001fff0000 - 0000000020000000 (usable)
BIOS-e820: 00000000feea0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
512MB LOWMEM available.
found SMP MP-table at 000f9bf0
Entering add_active_range(0, 0, 131072) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 131072
HighMem 131072 -> 131072
early_node_map[1] active PFN ranges
0: 0 -> 131072
On node 0 totalpages: 131072
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 992 pages used for memmap
Normal zone: 125984 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000E0010, 0014 (r0 COMPAQ)
ACPI: RSDT 000E0080, 005C (r1 COMPAQ CPQ0005 20020913 0)
ACPI: FACP 000E0130, 0074 (r1 COMPAQ SOLANO 1 0)
ACPI: DSDT 000E0204, 12F5 (r1 COMPAQ DSDT 1 MSFT 100000D)
ACPI: FACS 000E0040, 0040
ACPI: SSDT 000E14F9, 0174 (r1 COMPAQ CORE_UTL 1 MSFT 100000D)
ACPI: SSDT 000E166D, 0D1C (r1 COMPAQ VILLTBL1 1 MSFT 100000D)
ACPI: SSDT 000E33B3, 005D (r1 COMPAQ FHUB 1 MSFT 100000D)
ACPI: APIC 000E01A4, 0060 (r1 COMPAQ SOLANO 1 0)
ACPI: SSDT 000E333D, 0076 (r1 COMPAQ APIC 1 MSFT 100000D)
ACPI: SSDT 000E2389, 06AD (r1 COMPAQ PNP_PRSS 1 MSFT 100000D)
ACPI: SSDT 000E2A94, 01A4 (r1 COMPAQ S3 1 MSFT 100000D)
ACPI: SSDT 000E2C38, 0158 (r1 COMPAQ PIDETM 1 MSFT 100000D)
ACPI: SSDT 000E2EED, 010B (r1 COMPAQ GTF0 1 MSFT 100000D)
ACPI: SSDT 000E2FF8, 0117 (r1 COMPAQ GTF1 1 MSFT 100000D)
ACPI: SSDT 000E2D90, 015D (r1 COMPAQ SIDETM 1 MSFT 100000D)
ACPI: SSDT 000E310F, 0117 (r1 COMPAQ GTF2 1 MSFT 100000D)
ACPI: SSDT 000E349B, 004E (r1 COMPAQ FINIS 1 MSFT 100000D)
ACPI: PM-Timer IO Port: 0xf808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:deea0000)
Built 1 zonelists. Total pages: 130048
Kernel command line: root=/dev/hda1 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 996.822 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510088k/524288k available (1689k kernel code, 13380k reserved, 648k data, 244k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
.init : 0xc034f000 - 0xc038c000 ( 244 kB)
.data : 0xc02a65d7 - 0xc03487e4 ( 648 kB)
.text : 0xc0100000 - 0xc02a65d7 (1689 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1995.21 BogoMIPS (lpj=3990423)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
ACPI: Core revision 20070126
CPU0: Intel Pentium III (Coppermine) stepping 0a
Total of 1 processors activated (1995.21 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xe838d, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region f800-f87f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region fa00-fa3f claimed by ICH4 GPIO
PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: RTC can wake from S4
pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0e: ioport range 0x400-0x41f has been reserved
pnp: 00:0e: ioport range 0x420-0x43f has been reserved
pnp: 00:0e: ioport range 0x440-0x45f has been reserved
pnp: 00:0e: ioport range 0x460-0x47f has been reserved
pnp: 00:0e: ioport range 0xf800-0xf81f has been reserved
pnp: 00:0e: ioport range 0xf820-0xf83f has been reserved
pnp: 00:0e: ioport range 0xf840-0xf85f has been reserved
pnp: 00:0e: ioport range 0xf860-0xf87f has been reserved
pnp: 00:0f: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0f: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0f: iomem range 0x100000-0x1fffffff could not be reserved
pnp: 00:0f: iomem range 0xfff80000-0xffffffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:1e.0
IO window: 1000-1fff
MEM window: 40000000-413fffff
PREFETCH window: 41500000-4fffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 786432 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs...<6>Switched to high resolution mode on CPU 0
it is
Freeing initrd memory: 5901k freed
audit: initializing netlink socket (disabled)
audit(1196838639.324:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:02:04.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 244k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Processor [CPU0] (supports 8 throttling states)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 1
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2460-0x2467, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x2468-0x246f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
SCSI subsystem initialized
libata version 2.21 loaded.
hda: Maxtor 34098H4, ATA DISK drive
hdb: WDC WD200BB-00DEA0, ATA DISK drive
hda: selected mode 0x45
hdb: selected mode 0x45
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: COMPAQ SC-148F, ATAPI CD/DVD-ROM drive
hdc: selected mode 0x22
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: UHCI Host Controller
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.4: irq 16, io base 0x00002440
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 17
e100: eth0: e100_probe: addr 0x41000000, irq 17, MAC addr 00:02:A5:10:5A:37
sata_sil 0000:02:0b.0: version 2.2
ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 22 (level, low) -> IRQ 18
scsi0 : sata_sil
scsi1 : sata_sil
ata1: SATA max UDMA/100 cmd 0xe0812080 ctl 0xe081208a bmdma 0xe0812000 irq 18
ata2: SATA max UDMA/100 cmd 0xe08120c0 ctl 0xe08120ca bmdma 0xe0812008 irq 18
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=4)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=3)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=2)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to set xfermode (err_mask=0x40)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after completion, repeating EH (cnt=1)
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata1.00: 19541088 sectors, multi 16: LBA
ata1.00: applying bridge limits
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: revalidation failed (errno=-5)
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: limiting speed to UDMA/100:PIO3
ata1: failed to recover some devices, retrying in 5 secs
ata1: hard resetting port
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: failed to set xfermode (err_mask=0x40)
ata1.00: disabled
ata1: EH pending after 5 tries, giving up
ata1: EH complete
ata2: SATA link down (SStatus 0 SControl 310)
hda: max request size: 128KiB
hda: 80043264 sectors (40982 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 >
hdb: max request size: 128KiB
hdb: 39102336 sectors (20020 MB) w/8192KiB Cache, CHS=38792/16/63, UDMA(100)
hdb: cache flushes not supported
hdb: hdb1
hdc: ATAPI 48X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset.
agpgart: AGP aperture is 64M @ 0x0
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
input: PC Speaker as /class/input/input1
Floppy drive(s): fd0 is 1.44M
Real Time Clock Driver v1.12ac
FDC 0 is a post-1991 82077
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH2 TCO device (Version=1, TCOBASE=0xf860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Intel 82802 RNG detected
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.5 to 64
input: PS2++ Logitech MX Mouse as /class/input/input2
intel8x0_measure_ac97_clock: measured 52055 usecs
intel8x0: clocking to 41158
Adding 1642496k swap on /dev/hda5. Priority:-1 extents:1 across:1642496k
EXT3 FS on hda1, internal journal
ACPI: PCI interrupt for device 0000:02:0b.0 disabled
sata_sil 0000:02:0b.0: version 2.2b
ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 22 (level, low) -> IRQ 18
scsi2 : sata_sil
scsi3 : sata_sil
ata3: SATA max UDMA/100 cmd 0xe0886080 ctl 0xe088608a bmdma 0xe0886000 irq 18
ata4: SATA max UDMA/100 cmd 0xe08860c0 ctl 0xe08860ca bmdma 0xe0886008 irq 18
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata3.00: 19541088 sectors, multi 16: LBA
ata3.00: applying bridge limits
ata3.00: failed to set xfermode (err_mask=0x40)
ata3: failed to recover some devices, retrying in 5 secs
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata3.00: revalidation failed (errno=-5)
ata3.00: limiting speed to UDMA/100:PIO3
ata3: failed to recover some devices, retrying in 5 secs
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata3.00: revalidation failed (errno=-5)
ata3.00: disabled
ata3: EH pending after completion, repeating EH (cnt=4)
ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata3.00: 19541088 sectors, multi 16: LBA
ata3.00: applying bridge limits
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata3.00: revalidation failed (errno=-5)
ata3: failed to recover some devices, retrying in 5 secs
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to set xfermode (err_mask=0x40)
ata3.00: limiting speed to UDMA/100:PIO3
ata3: failed to recover some devices, retrying in 5 secs
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata3.00: revalidation failed (errno=-5)
ata3.00: disabled
ata3: EH pending after completion, repeating EH (cnt=3)
ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata3.00: 19541088 sectors, multi 16: LBA
ata3.00: applying bridge limits
ata3.00: failed to set xfermode (err_mask=0x40)
ata3: failed to recover some devices, retrying in 5 secs
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to set xfermode (err_mask=0x40)
ata3.00: limiting speed to UDMA/100:PIO3
ata3: failed to recover some devices, retrying in 5 secs
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to set xfermode (err_mask=0x40)
ata3.00: disabled
ata3: EH pending after completion, repeating EH (cnt=2)
ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata3.00: 19541088 sectors, multi 16: LBA
ata3.00: applying bridge limits
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata3.00: revalidation failed (errno=-5)
ata3: failed to recover some devices, retrying in 5 secs
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata3.00: revalidation failed (errno=-5)
ata3.00: limiting speed to UDMA/100:PIO3
ata3: failed to recover some devices, retrying in 5 secs
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to set xfermode (err_mask=0x40)
ata3.00: disabled
ata3: EH pending after completion, repeating EH (cnt=1)
ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: ATA-5: ST310216A, 3.01, max UDMA/100
ata3.00: 19541088 sectors, multi 16: LBA
ata3.00: applying bridge limits
ata3.00: failed to set xfermode (err_mask=0x40)
ata3: failed to recover some devices, retrying in 5 secs
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata3.00: revalidation failed (errno=-5)
ata3.00: limiting speed to UDMA/100:PIO3
ata3: failed to recover some devices, retrying in 5 secs
ata3: hard resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3: XXX SATA_IRQ, serror=0x0
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata3.00: revalidation failed (errno=-5)
ata3.00: disabled
ata3: EH pending after 5 tries, giving up
ata3: EH complete
ata4: SATA link down (SStatus 0 SControl 310)
begin:vcard
fn:Mark Paulus
n:Paulus;Mark
org:MCI;Lec Interfaces / 40419
adr;dom:;;2424 Garden of the Gods Rd;Colorado Springs;CO;80919
email;internet:mark.paulus@xxxxxxxxxxxxxxxxxxx
title:Mark Paulus
tel;work:719-535-5578
tel;pager:800-pagemci / 1406052
tel;home:v622-5578
version:2.1
end:vcard
